HONDA          07-08 FIT/ 07-09 CIVIC                                    ELECTRONIC CRUISE KIT
Part Number: 250-1896      ...
HONDA             07-08 FIT/ 07-09 CIVIC                            ELECTRONIC CRUISE KIT
Part Number: 250-1896           ...
HONDA        07-08 FIT/ 07-09 CIVIC                              ELECTRONIC CRUISE KIT
Part Number: 250-1896              ...
HONDA           07-08 FIT/ 07-09 CIVIC                              ELECTRONIC CRUISE KIT
Part Number: 250-1896           ...
HONDA         07-08 FIT/ 07-09 CIVIC                                ELECTRONIC CRUISE KIT
Part Number: 250-1896           ...
HONDA         07-08 FIT/ 07-09 CIVIC                                 ELECTRONIC CRUISE KIT
Part Number: 250-1896          ...
HONDA          07-08 FIT/ 07-09 CIVIC   ELECTRONIC CRUISE KIT
Section II – Installation Procedure




  Form #5183 Rev: B ...
HONDA         07-08 FIT/ 07-09 CIVIC   ELECTRONIC CRUISE KIT
Section III – Wiring Diagram




  Form #5183 Rev: B   11-06-...
ROSTRA.COM

Form #5183 Rev: B   11-06-08
Upcoming SlideShare
Loading in …5
×

HONDA 07-08 FIT/ 07-09 CIVIC ELECTRONIC CRUISE KIT

313 views

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
313
On SlideShare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
3
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

HONDA 07-08 FIT/ 07-09 CIVIC ELECTRONIC CRUISE KIT

  1. 1. HONDA 07-08 FIT/ 07-09 CIVIC ELECTRONIC CRUISE KIT Part Number: 250-1896 MANUAL AND AUTOMATIC TRANSMISSION Section II – Installation Procedure M/T Vehicles Require Clutch Switch Part # 250-4206 A. Pre-Installation Suggestions Kit Contents/Service Parts of: Item # Qty Description 1. It is advisable to disconnect the negative 1. 250-2740 1 Cruise Control Module battery cable for 3 minutes before beginning 2. 250-2741 1 Switch Interface Module 3. 250-2742 1 Main Wiring Harness installation, to avoid unintended air bag 4. 250-2743 1 Pedal Interface Harness deployment. Note and record any anti-theft 5. 250-2744 1 Hardware Kit radio codes prior to disconnecting. Figure 1 6. 250-2745 1 Control Switch 2. Remove the driver side fuse panel cover. B. Install Electronic Modules 1. There are two electronic modules. The larger one is the Cruise Control Module and the smaller one is the Switch Interface Module. 2. Apply the larger supplied piece of double- sided adhesive tape to the Cruise Control Module, and the smaller piece of double-sided Figure 1 tape to the Switch Interface Module. 3. Assemble 20-pin connector from Main Wiring Harness onto mating connector of Cruise Control Module. Apply the 10 and 4 pin connectors from Pedal Interface Harness to mating connector on Switch Interface Module. Figure 2 Warning: Be sure to use the 4 pin connector that is on the same side of the wire harness fuse as the 10 pin connector. Failure to do so Figure 2 could damage vehicle’s ECM. See the picture insert in Figure 3 for further guidance. 4. Locate the linked harness between the Cruise Control and Switch Interface Modules. Connect the four pin mating connectors. 5. Place the Cruise Control Module and the Switch Interface Module in a secure location behind the driver side dash area. 6. Route the Pedal Interface Harness through steering column and down to the accelerator. Figure 3 Form #5183 Rev: B 11-06-08
  2. 2. HONDA 07-08 FIT/ 07-09 CIVIC ELECTRONIC CRUISE KIT Part Number: 250-1896 MANUAL AND AUTOMATIC TRANSMISSION 7. Locate the 6 pin plug and mate connectors on the Pedal Interface Harness. Remove the accelerator 6-pin connector and apply to mating connector of Pedal Interface Harness. Apply the other connector to the accelerator. Figure 4 C. Honda Fit Wiring Connections 1. Use the supplied self-stripping connectors (T- taps) from hardware pack to apply a T-tap Figure 4 onto the following J/B wires: See Fuse Box Function Fig. Vehicle Color IGN 5 YELLOW/BLUE BRAKE + 6 WHITE/GREEN BRAKE - 6 WHITE/BLACK GROUND 7 BLACK IGN A/T 8 VIOLET M/T VSS 10 WHITE/GREEN Figure 5 NSS for A/T 11 RED/BLACK CLUTCH SWITCH 12 WHITE/BLACK Figure 6 2. Use the following wires from the Main Brake Switch Harness to connect to vehicle T-tapped wire: Cruise Harness Vehicle T- Function Color Tap Wire IGN ORANGE YELLOW/BLUE BRAKE + BROWN WHITE/GREEN BRAKE - BROWN/WHITE WHITE/BLACK VSS BLUE VIOLET/WHITE GROUND GREEN BLACK Fuse Box Ground NSS for A/T VIOLET RED/BLACK CLUTCH SWITCH VIOLET WHITE/BLACK TACH YELLOW NOT USED Form #5183 Rev: B 11-06-08
  3. 3. HONDA 07-08 FIT/ 07-09 CIVIC ELECTRONIC CRUISE KIT Part Number: 250-1896 MANUAL AND AUTOMATIC TRANSMISSION Honda Fit Continued… 3. Automatic Transmission VSS: Locate the Figure 7 ECM behind glove box. Connect the Blue ECM Wire from the Main Wiring Harness to the Violet/White Wire (VSS) of the first white connector at the ECM. Figure 8. 4. Manual Transmission VSS: Remove battery. Figure 9. Route the blue wire from the Main Wiring Harness through the VSS for A/T grommet on the fire wall. Locate the three wire gray connector on the top of the Figure 8 transmission. Connect the Blue Wire from the Main Wiring harness to the White/Green Wire (VSS). Figure 10. 5. NSS for Automatic Transmissions: Remove battery. Locate 10-pin Gray Connector above transmission and behind removed battery. Use the supplied red t-tap to connect the Violet Wire from the Main Wiring Harness to the Red/Black Wire in connector. Figure 11 6. Clutch Switch for Manual Transmissions: Install clutch switch Part# 250-4206. Figure 12. Connect one of the two Violet Wires Figure 9 from the clutch switch to the Brown/White Wire from the Cruise Control Module harness. Connect the other violet wire to the VSS for M/T White/Black Wire (brake negative) of brake switch. 7. Apply the supplied weather sealant to the connections in the engine compartment. Be sure all of connection is sealed properly. 8. Secure Cruise Control and Switch Interface Module harnesses with zip ties away from moving parts. Figure 10 NSS Clutch Switch Figure 12 Figure 11 Form #5183 Rev: B 11-06-08
  4. 4. HONDA 07-08 FIT/ 07-09 CIVIC ELECTRONIC CRUISE KIT Part Number: 250-1896 MANUAL AND AUTOMATIC TRANSMISSION D. Honda Civic Wiring Connections Junction Box 9. Use the supplied self-stripping connectors (T- IGN taps) from hardware pack to apply a T-tap onto the following wires: See Function Fig. Vehicle Color IGN 13 RED Figure 13 BRAKE + 14 WHITE BRAKE - 14 LT. GREEN GROUND 15 BLACK Brake Switch VSS 16 BLUE NSS for A/T 18 RED/BLACK CLUTCH SWITCH 19 WHITE/BLACK 10. Use the following wires from the Main Harness to connect to vehicle T-tapped wire: Figure 14 Cruise Harness Vehicle T- Function Color Tap Wire IGN ORANGE RED Figure 15 Ground BRAKE + BROWN WHITE BRAKE - BROWN/WHITE LT. GREEN VSS BLUE BLUE GROUND GREEN BLACK NSS for A/T VIOLET RED/BLACK CLUTCH SWITCH VIOLET LT. GREEN TACH YELLOW NOT USED Form #5183 Rev: B 11-06-08
  5. 5. HONDA 07-08 FIT/ 07-09 CIVIC ELECTRONIC CRUISE KIT Part Number: 250-1896 MANUAL AND AUTOMATIC TRANSMISSION Honda Civic Continued… 11. VSS: Remove panels below radio, and ahead of shifter. Then remove two 8mm bolts which hold radio in place. Remove lower dash panel, and then look high on driver’s side to VSS remove black screw that holds cluster shroud in place. Pull shroud back toward the wheel to remove. It is clipped in place. Then do the same for the radio. Locate the middle gray connector behind the radio. Connect the Blue Wire from the Main Wiring Harness to the Figure 16 Blue Wire (VSS) of the connector as shown in Figure 8. 12. NSS for Automatic Transmissions: Remove battery. Locate 10-pin Gray Connector above transmission and behind removed battery. Use the supplied red t-tap to connect the Violet Wire from the Main Wiring Harness to the Red/Black Wire in connector. Figure 11 13. Clutch Switch for Manual Transmissions: Install clutch switch Part# 250-4206. Figure 12. Connect one of the two Violet Wires from the clutch switch to the Brown/White Figure 17 Wire from the Cruise Control Module harness. Connect the other violet wire to the LT. Green Wire (brake negative) of brake NSS switch. 14. Apply the supplied weather sealant to the connections in the engine compartment. Be sure all of connection is sealed properly. 15. Secure Cruise Control and Switch Interface Module harnesses with zip ties away from moving parts. Figure 18 Clutch Switch Figure 19 Form #5183 Rev: B 11-06-08
  6. 6. HONDA 07-08 FIT/ 07-09 CIVIC ELECTRONIC CRUISE KIT Part Number: 250-1896 MANUAL AND AUTOMATIC TRANSMISSION D. Install Control Switch Figure 20 Fit 16. Drill a 3/8”hole on the driver side dash in the area as shown in Figure 20. 17. Use the supplied double-sided tape in kit and apply to the back of switch. 18. Route the switch harness through hole and mount the switch on the dash covering the previously drilled hole. Figures 21 & 22 19. Assemble 8-pin connector from the sack parts Drill 3/8” Hole to the mating wire colors on the Control switch harness. Figure 21 20. Connect the assembled Control Switch harness to the mating connector from the Cruise Control harness. D. Testing 1. Reconnect negative battery cable and torque to 35 lbs. Reenter anti-theft radio codes. Fit 2. Turn ignition on. Apply the on/off button of Cruise Control Switch. F. Reassembly Civic 1. Reinstall all removed pieces taking care to ensure harnesses and wiring connections are properly secured. 2. Make sure all harnesses are not pinched or bound by trim pieces. Figure 22 Form #5183 Rev: B 11-06-08
  7. 7. HONDA 07-08 FIT/ 07-09 CIVIC ELECTRONIC CRUISE KIT Section II – Installation Procedure Form #5183 Rev: B 11-06-08
  8. 8. HONDA 07-08 FIT/ 07-09 CIVIC ELECTRONIC CRUISE KIT Section III – Wiring Diagram Form #5183 Rev: B 11-06-08
  9. 9. ROSTRA.COM Form #5183 Rev: B 11-06-08

×