Data communication part1

339 views

Published on

Unlike other data communication slide i think this one is the simplest.
Found in the internet,i had no intention to change anything.Though i know the color sucks.. :P

Published in: Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
339
On SlideShare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
18
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Data communication part1

  1. 1. Introduction • • • • • Data Communication Networks Protocols and Standards Standard Organizations Basic Concepts
  2. 2. Introdution to Computer Networks Computer Networks Computer network connects two or more autonomous computers.
  3. 3. Introduction to Computer Networks Applications of Networks Resource Sharing Hardware (computing resources, disks, printers) Software (application software) Information Sharing Easy accessibility from anywhere (files, databases) Search Capability (WWW) Communication Email Message broadcast Remote computing
  4. 4. Data Communication System Components
  5. 5. Basic Concepts • • • • • Line Configuration Topology Transmission Mode Categories of Networks Internetworks
  6. 6. Point-to-Point Line Configuration
  7. 7. Point-to-Point Line Configuration
  8. 8. Point-to-Point Line Configuration
  9. 9. Multipoint Line Configuration
  10. 10. Simplex
  11. 11. Half-Duplex
  12. 12. Full-Duplex
  13. 13. LAN, MAN & WAN Network in small geographical Area (Room, Building or a Campus) is called LAN (Local Area Network) Network in a City is call MAN (Metropolitan Area Network) Network spread geographically (Country or across Globe) is called WAN (Wide Area Network)
  14. 14. Local Area Network
  15. 15. Local Area Network
  16. 16. Metropolitan Area Network
  17. 17. Wide Area Network
  18. 18. Figure 2-19 WCB/McGraw-Hill Internetwork (Internet) © The McGraw-Hill Companies, Inc., 1998
  19. 19. Introduction to Comuter Networks Network Topology The network topology defines the way in which computers, printers, and other devices are connected. A network topology describes the layout of the wire and devices as well as the paths used by data transmissions.
  20. 20. Introduction to Computer Networks Mesh Topology The mesh topology connects all devices (nodes) to each other for redundancy and fault tolerance. It is used in WANs to interconnect LANs and for mission critical networks like those used by banks and financial institutions. Implementing the mesh topology is expensive and difficult.
  21. 21. Mesh Topology Merits Demerits • No congestion • Cable length problem • Impractical for large • No MAC protocols networks are needed • More Secure • It is Robust • Fault identification is easy
  22. 22. Itroduction to Computer Networks Star & Tree Topology The star topology is the most commonly used architecture in Ethernet LANs. When installed, the star topology resembles spokes in a bicycle wheel. Larger networks use the extended star topology also called tree topology. When used with network devices that filter frames or packets, like bridges, switches, and routers, this topology significantly reduces the traffic on the wires by sending packets only to the wires of the destination host.
  23. 23. Star & Tree Topology Merits • Cheaper than Mesh Topology • Relatively easier to install, maitain & configure Demerits • If hub goes down the entire network becomes defunct
  24. 24. Introduction to Computer Networks Ring Topology A frame travels around the ring, stopping at each node. If a node wants to transmit data, it adds the data as well as the destination address to the frame. The frame then continues around the ring until it finds the destination node, which takes the data out of the frame. Single ring – All the devices on the network share a single cable Dual ring – The dual ring topology allows data to be sent in both directions.
  25. 25. Ring topology Merits • Easy to reconfigure and install. • Fault isolation is relatively easy in a ring. Demerits • If a node in a simple ring fails, the whole ring can not function.
  26. 26. Bus Topology Commonly referred to as a linear bus, all the devices on a bus topology are connected by one single cable.
  27. 27. Bus Topology Merits • Easy to install • Uses less cable Demerits • Relatively difficult to add new nodes. • Even if a portion of the bus breaks down, the whole bus can not function.

×