By Mike  O’Dell 10/16/2011 <ul><li>Field Failures & Customer Complaints </li></ul><ul><li>Cost and Improvement </li></ul><...
<ul><li>Burned contacts </li></ul><ul><li>Burned coils </li></ul><ul><li>Open coils </li></ul><ul><li>Stripped Screws/term...
<ul><li>Mismatch between device current/voltage ratings and load </li></ul><ul><li>Low voltage at the coil causing chatter...
<ul><li>Low voltage to the coil – below contactor pickup volts </li></ul><ul><li>High voltage to the coil – exceeding coil...
<ul><li>Reliability issue with magnet wire termination – bad solder or crimp joint  </li></ul><ul><li>Voltage surge causin...
<ul><li>Threads not per specification </li></ul><ul><li>Screws not started correctly </li></ul><ul><li>Excessive tightenin...
Approximate material cost breakdown of typical contactor device
<ul><li>Expensive silver alloys formulated and sized for required electrical life. </li></ul><ul><li>Silver Oxide has low ...
<ul><li>Mass of copper magnet wire – specific gages for different voltages. </li></ul><ul><li>Stamped and formed terminals...
<ul><li>Special alloy core-plated steel selected for specific application.  Few steel mills produce this type of steel.  T...
<ul><li>Stamping, assembly and finishing magnet (grinding) is costly. </li></ul><ul><li>Often have copper/aluminum shading...
<ul><li>Special insulative and track/arc resistive molding compound for contact boards and cross-arms. </li></ul><ul><li>M...
<ul><li>Brass or copper, stamped, formed, plated, drilled and tapped </li></ul>Springs Contact Carriers Labor cost to asse...
<ul><li>Reduce or eliminate silver contacts – eliminate Cd </li></ul><ul><li>Reduce coil size or eliminate coil completely...
L1 L2 T1 T2 LINE LOAD CONTROL CIRCUIT
<ul><li>Solid State (MOSFET) and Semiconductor (Thyristor) Relays and Contactors – issues with heat, leakage and transient...
<ul><li>Grandfathered materials/ratings in UL 508, IEC 60947 or other relevant standard such as ARI 780/790 </li></ul><ul>...
<ul><li>UL 508 – Standard of Safety for Industrial Control Equipment </li></ul><ul><li>Intended for control and accessory ...
ARMATURE MAGNET A SMALL GAP IS LEFT TO BREAK THE MAGNETIC FIELD AND ALLOW ARMATURE TO DROP AWAY FREELY AFTER COIL IS DE-EN...
 
 
 
 
 
 
<ul><li>Inrush current – current during the first few cycles of coil energization – before the armature closes onto the ma...
<ul><li>Low voltage – produces low currents and low magnetic pull.  When the voltage is greater than the pick up voltage a...
<ul><li>Copper & Aluminum wire </li></ul><ul><li>Round, Rectangular or Square X-Section </li></ul><ul><li>Ratings from 105...
<ul><li>Windings </li></ul><ul><li>Precision wound – turns are laid side by side & wire traverses </li></ul><ul><li>from o...
<ul><li>Coils can be encapsulated, over molded, varnished </li></ul><ul><li>AC coils must withstand inrush current until t...
<ul><li>Very common today at low voltage <12 volts.  Design become costly at higher voltages. </li></ul><ul><li>Depends on...
<ul><li>“ True” DC coil </li></ul><ul><li>One large (tall) single winding to absorb/dissipate heat. </li></ul><ul><li>Two ...
<ul><li>Arcing phenomena varies with electrode/contact material and contamination </li></ul><ul><li>To breakdown a large a...
AC arc suppression <ul><li>Arcing occurs at greater than 12VAC and is greatest when opening contacts </li></ul><ul><li>AC ...
DC arc suppression <ul><li>DC requires only one set of contacts per device </li></ul><ul><li>Rapid opening of contacts wit...
Upcoming SlideShare
Loading in …5
×

Contactor Generalizations

531 views

Published on

Contactor issues learned with job experience

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
531
On SlideShare
0
From Embeds
0
Number of Embeds
2
Actions
Shares
0
Downloads
13
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Contactor Generalizations

  1. 1. By Mike O’Dell 10/16/2011 <ul><li>Field Failures & Customer Complaints </li></ul><ul><li>Cost and Improvement </li></ul><ul><li>Agencies and Standards </li></ul><ul><li>Magnetic Circuit </li></ul><ul><li>Coil Design and Issues </li></ul><ul><li>Contacts </li></ul>
  2. 2. <ul><li>Burned contacts </li></ul><ul><li>Burned coils </li></ul><ul><li>Open coils </li></ul><ul><li>Stripped Screws/terminal threads or loose connection </li></ul><ul><li>Noise </li></ul><ul><li>Loose/misaligned springs </li></ul>
  3. 3. <ul><li>Mismatch between device current/voltage ratings and load </li></ul><ul><li>Low voltage at the coil causing chattering and excessive arcing of contacts </li></ul><ul><li>Bad riveting of contacts to carrier </li></ul><ul><li>Environmental causes (temperature, humidity, minerals) </li></ul>Burned Contacts Severity of Failure <ul><li>Arcing may propagate and create further damage and fire </li></ul><ul><li>Costly to replace in field installed equipment </li></ul><ul><li>Critical systems would require backup or redundant system </li></ul>
  4. 4. <ul><li>Low voltage to the coil – below contactor pickup volts </li></ul><ul><li>High voltage to the coil – exceeding coil rating </li></ul><ul><li>Many nicked wire turns – insulation removed causing shorts </li></ul><ul><li>Environmental causes </li></ul>Burned Coils Severity of Failure <ul><li>Burned coils release toxic gases and may potentially contribute to a fire </li></ul><ul><li>Costly to replace in field installed equipment </li></ul><ul><li>Critical systems would require backup or redundant system </li></ul>
  5. 5. <ul><li>Reliability issue with magnet wire termination – bad solder or crimp joint </li></ul><ul><li>Voltage surge causing terminations to break </li></ul><ul><li>Coil opens at another location such as outer winding due to previous damage </li></ul><ul><li>Environmental causes </li></ul>Open Coils Severity of Failure <ul><li>Failure to operate may be intermittent depending on nature of break </li></ul><ul><li>Open coils are not normally a safety problem for the equipment </li></ul><ul><li>Costly to replace in field installed equipment </li></ul><ul><li>Critical systems would require backup or redundant system </li></ul>
  6. 6. <ul><li>Threads not per specification </li></ul><ul><li>Screws not started correctly </li></ul><ul><li>Excessive tightening torque </li></ul><ul><li>Environmental causes (corrosion) </li></ul>Stripped Screws – Customer Connections Severity of Failure <ul><li>Customer connection may not be secure. Potential fire hazard. </li></ul><ul><li>Costly to replace in field installed equipment </li></ul>
  7. 7. Approximate material cost breakdown of typical contactor device
  8. 8. <ul><li>Expensive silver alloys formulated and sized for required electrical life. </li></ul><ul><li>Silver Oxide has low resistance </li></ul><ul><li>Good mechanical strength and wear resistance </li></ul><ul><li>Can be brazed or riveted to contact carrier </li></ul><ul><li>Arc quenching parts/materials are added when needed </li></ul>Silver Contacts
  9. 9. <ul><li>Mass of copper magnet wire – specific gages for different voltages. </li></ul><ul><li>Stamped and formed terminals to meet customer connection requirements. Brass terminals typically tin-plated for soldering. </li></ul><ul><li>Termination process costly – special tooling for strip/crimp or materials/labor for solder termination. </li></ul><ul><li>Bobbin molds, material and time to mold add cost. </li></ul><ul><li>Overmolds, housings, varnish, sealants </li></ul>Coils
  10. 10. <ul><li>Special alloy core-plated steel selected for specific application. Few steel mills produce this type of steel. Typically soft iron material that is magnetized when magnetic field created. </li></ul><ul><li>Magnets used with AC coils are comprised of thin laminated sheets which limit the eddy current and heat. </li></ul><ul><li>DC coil may use solid steel due to one way current – no eddy current </li></ul>High Cost Components and Processes in Contactors and Relays
  11. 11. <ul><li>Stamping, assembly and finishing magnet (grinding) is costly. </li></ul><ul><li>Often have copper/aluminum shading rings for AC. </li></ul>High Cost Components and Processes in Contactors and Relays
  12. 12. <ul><li>Special insulative and track/arc resistive molding compound for contact boards and cross-arms. </li></ul><ul><li>Molds and material are expensive and time to mold is costly. </li></ul>Plastic
  13. 13. <ul><li>Brass or copper, stamped, formed, plated, drilled and tapped </li></ul>Springs Contact Carriers Labor cost to assemble
  14. 14. <ul><li>Reduce or eliminate silver contacts – eliminate Cd </li></ul><ul><li>Reduce coil size or eliminate coil completely </li></ul><ul><li>Eliminate or reduce coil inrush current </li></ul><ul><li>Reduce, reconfigure or eliminate the magnet/armature assembly </li></ul><ul><li>Reduce housing size </li></ul><ul><li>Less mechanical motion – fewer/smaller springs </li></ul><ul><li>Survive non-standard voltages to coil </li></ul><ul><li>Maintain or improve resistance to environmental issues </li></ul>
  15. 15. L1 L2 T1 T2 LINE LOAD CONTROL CIRCUIT
  16. 16. <ul><li>Solid State (MOSFET) and Semiconductor (Thyristor) Relays and Contactors – issues with heat, leakage and transients </li></ul><ul><li>Latching relay – reduces coil size/no hum. Used often for lighting control . </li></ul>
  17. 17. <ul><li>Grandfathered materials/ratings in UL 508, IEC 60947 or other relevant standard such as ARI 780/790 </li></ul><ul><li>Compatibility of field replacement with existing products </li></ul><ul><li>Coil (control voltage) ratings </li></ul><ul><li>Customer/end user mounting requirements </li></ul><ul><li>Number of poles and contact arrangement required in applications. </li></ul><ul><li>Auxiliary contact requirements </li></ul><ul><li>Labeling </li></ul><ul><li>RoHS and REACH </li></ul><ul><li>Specific Engineering Test Requirements not covered in the Standards </li></ul>
  18. 18. <ul><li>UL 508 – Standard of Safety for Industrial Control Equipment </li></ul><ul><li>Intended for control and accessory devices for starting, stopping, regulating, controlling or protecting electric motors. </li></ul><ul><li>Requirements for construction, electrical clearances, insulation, grounding, marking, wiring. </li></ul><ul><li>Overload, endurance, dielectric withstand, short circuit, over &under voltage and temperature are important tests. </li></ul><ul><li>IEC 60947 (part 4 for contactors)-similar to UL508 with exception of IEC ratings </li></ul><ul><li>ARI 780/790-97 – inactive standard intended for Definite Purpose contactors (used in air conditioning equipment). OEM’s request testing to the requirements of this standard – the electrical and mechanical life test minimums and temperature rise requirements are more stringent than UL 508. </li></ul><ul><li>Other standards as applicable to specific product. </li></ul>
  19. 19. ARMATURE MAGNET A SMALL GAP IS LEFT TO BREAK THE MAGNETIC FIELD AND ALLOW ARMATURE TO DROP AWAY FREELY AFTER COIL IS DE-ENERGIZED SHADING COIL
  20. 26. <ul><li>Inrush current – current during the first few cycles of coil energization – before the armature closes onto the magnet. Inrush can be simulated by holding the armature in position. </li></ul><ul><li>Sealed current – Current when armature is pulled in completely at coil rated voltage. </li></ul><ul><li>Inrush current is much large than sealed current. Magnetic circuit when sealed increases impedance in coil circuit thereby reducing current. </li></ul><ul><li>Pickup voltage – minimum control voltage which will cause the armature to start to move </li></ul><ul><li>Seal in voltage – minimum control voltage required to cause the armature to seat against the pole faces of the magnet </li></ul><ul><li>Drop out voltage – exists when the voltage is reduced to allow the contactor to open </li></ul>
  21. 27. <ul><li>Low voltage – produces low currents and low magnetic pull. When the voltage is greater than the pick up voltage and less than the seal voltage the contactor may pick up but will not seal. As the coil is not designed to carry the greater current continuously, it will get hot and will either be damaged or burn out. The armature will chatter – creating noise and wearing magnetic pole faces. </li></ul><ul><li>High voltage – Drawing higher than rated current will cause damage and possible failure. The excessive force of the armature closing will wear the pole faces prematurely. </li></ul><ul><li>AC Hum – due to changing magnetic field, inducing mechanical vibration. Excessive noise can be caused by: broken shading coil, low voltage to coil, wrong coil, misalignment between magnet and armature. </li></ul>
  22. 28. <ul><li>Copper & Aluminum wire </li></ul><ul><li>Round, Rectangular or Square X-Section </li></ul><ul><li>Ratings from 105C to 220C </li></ul><ul><li>Many insulation materials ranging from Polyvinyl (105) to Aromatic Polyamide (220) </li></ul><ul><li>Insulation thickness can vary </li></ul><ul><li>Wire gages from 4/0 to 46 AWG </li></ul>Magnet Wire
  23. 29. <ul><li>Windings </li></ul><ul><li>Precision wound – turns are laid side by side & wire traverses </li></ul><ul><li>from one end of the bobbin to the other and back again during </li></ul><ul><li>winding. Reduces voltage gradient with the coils and prevent </li></ul><ul><li>accidental shorts. Winding thickness consistent </li></ul><ul><li>Random wound – Wire traverses back and forth across the bobbin but consecutive turns are not always adjacent. Winding thickness varies. Packs more copper in smaller space due to tighter nesting. Less costly because of higher winding speed. </li></ul>
  24. 30. <ul><li>Coils can be encapsulated, over molded, varnished </li></ul><ul><li>AC coils must withstand inrush current until the contactor closes </li></ul><ul><li>Volts/turn useful parameter to help select wire gage and number of turns based on limits of bobbin design </li></ul><ul><li>I²R heating, surface area and wire insulation affect wire size selection </li></ul><ul><li>Various coil voltages are used in the same coil/contactor family </li></ul><ul><li>UL listed insulation systems often required for contactors in N.A. </li></ul>
  25. 31. <ul><li>Very common today at low voltage <12 volts. Design become costly at higher voltages. </li></ul><ul><li>Depends on magnet/armature design – ideally a DC coil will have a solid magnet/armature (not always the case due to product extensions). </li></ul><ul><li>DC coil needs high resistance due to lack of inductance in magnet circuit – thinner magnet wire than equivalent AC coil. </li></ul><ul><li>Higher numbers of amp-turns are needed than in AC coils due to lower current. </li></ul><ul><li>Diodes often used to reduce DC spike during de-energization of coil </li></ul>
  26. 32. <ul><li>“ True” DC coil </li></ul><ul><li>One large (tall) single winding to absorb/dissipate heat. </li></ul><ul><li>Two winding DC coil </li></ul><ul><li>One “pickup” winding to absorb inrush current. </li></ul><ul><li>One “hold” winding capable of lower power after contactor closes. </li></ul><ul><li>Late break auxiliary contact removes pickup winding from circuit during contact closure. </li></ul><ul><li>Electronic DC coil </li></ul><ul><li>Primarily 24VDC product </li></ul>
  27. 33. <ul><li>Arcing phenomena varies with electrode/contact material and contamination </li></ul><ul><li>To breakdown a large air gap a minimum of 320V is needed </li></ul><ul><li>Very small gaps will generate an arc with an intense electric field </li></ul><ul><li>Minimum voltage to sustain an arc in air with small gaps is around 12 volts for most contact materials (less for Gold) </li></ul><ul><li>Above the minimum arc voltage: </li></ul><ul><li>Properly designed and operating device some arcing when contacts come together and more arcing at contact separation </li></ul><ul><li>DC arc can be sustained at gaps roughly proportional to voltage – 10 to 20 V/cm. </li></ul>
  28. 34. AC arc suppression <ul><li>Arcing occurs at greater than 12VAC and is greatest when opening contacts </li></ul><ul><li>AC may have several sets of contacts to make/break all legs </li></ul><ul><li>Self extinguishing due to current crossing zero. </li></ul><ul><li>Anode/Cathode side is random – movable and stationary contacts erode at equal rates </li></ul><ul><li>Higher currents and voltage require additional means to quench the arc after the first half cycle </li></ul>
  29. 35. DC arc suppression <ul><li>DC requires only one set of contacts per device </li></ul><ul><li>Rapid opening of contacts with enough air gap is necessary to break arc </li></ul><ul><li>Arc splitters commonly used with low voltage contactors </li></ul><ul><li>Rapid closing may cause contact bounce and accelerated erosion </li></ul><ul><li>Current flows in one direction and one contact will be anode and the other will be cathode </li></ul>

×