How–To setup Wireless Client Bridge as CPEfor connect WISPAnd Using Broadband Router to Create New Sub-Network (subnet)   ...
| Network Device Requirement   1. Outdoor Wireless Access Point (AP) as CPE          a. Use these devices as wireless clie...
| Step-by-Step   1. Reset your AP to default, I use EnGenius EOC-2610 as CPE   2. Open web console of your AP point your b...
7. Setup Sub Network,      Open Web console of Broadband Router(I use ASUSTEK WL-500gP v2)      Connect byusingdefault IP ...
13. Configure IP Scope for Sub Network and Verify your DHCP Server Setting   14. Click Apply Click Finish click “Save & ...
1.4                                                                            Wireless                                   ...
Upcoming SlideShare
Loading in …5
×

How–to setup wireless client bridge as CPE for connect WISP and using broadband router to create new sub network (subnet) rev2.2

3,213 views
2,912 views

Published on

How–to setup wireless client bridge as CPE for connect WISP and using broadband router to create new sub network (subnet) rev2.2

Published in: Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
3,213
On SlideShare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
42
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

How–to setup wireless client bridge as CPE for connect WISP and using broadband router to create new sub network (subnet) rev2.2

  1. 1. How–To setup Wireless Client Bridge as CPEfor connect WISPAnd Using Broadband Router to Create New Sub-Network (subnet) WISP TOT-WiFi, True-WiFi, WISP CPE 3bbFigure 1. Environment long distance Wireless Internet Access WiFiWi-Fi” LAN admin broadband router WPA Smart Phone, Laptop, Tablet PC Reset WANIP Setting smart phone / PDA tablet pc OutdoorWireless Access Pointbroadband router GatewayBy Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 1 of 6
  2. 2. | Network Device Requirement 1. Outdoor Wireless Access Point (AP) as CPE a. Use these devices as wireless client bridge as CPE. b. Use default IP for setting. 2. Broadband Router for Setup New Sub Network. a. Use this devices as router / dhcp / gateway for create new subnet network b. Use IP address of WISP (WiFi Network) for static IP setting as WAN’s IP 3. Accessory i.e. Camera Stand, Small UPS, 250 Watt DC-AC Converter | Network Diagram WiFi and LAN Switch IP: 192.168.2.1/24 Gateway: 192.168.2.1 RJ45Cablewith DNS:192.168.2.1 1 KM POE injection DHCP Server IP Setting: WISP CP 192.168.2.20-254 EIP Network:192.168.0.0/24Gateway: 192.168.0.1 -Use RJ45 Connect WAN PortDNS:192.168.0.1 Configure as static IP Setting LAN Port to WANDHCPscope: 192.168.0.101-254 Port on Router IP Addr: 192.168.0.54 -This AP will running Mask: 255.255.255.0 “Client bridge” mode Gateway: 192.168.0.1 -Use default setting DNS: 192.168.0.1Figure 2.Network Conceptual DiagramBy Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 2 of 6
  3. 3. | Step-by-Step 1. Reset your AP to default, I use EnGenius EOC-2610 as CPE 2. Open web console of your AP point your browser to http://192.168.1.1 3. Select Operation Mode as “Client Bridge” in system properties Click Apply 4. Go to menu “Wireless Network”  Click “Site Survey” 5. Select WiFi ISP that you want to connect select mac address on “BSSID” Column 6. Click Apply then you can see the connection status on menu “Connection Status” WISP AP Client BridgeBy Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 3 of 6
  4. 4. 7. Setup Sub Network, Open Web console of Broadband Router(I use ASUSTEK WL-500gP v2) Connect byusingdefault IP address http://192.168.1.1 Please change to new ip if the LAN IP of your router same as Outdoor Access Point (AP) 8. Change IP address of Router to new subnet, I use 192.168.2.1 on LAN IP Setting(Option) 9. Click Apply Click Finish click “Save & Restart” and wait for 20sec to restart(Option) 10. Open Web console of Broadband Router by default IP address http://192.168.2.1 11. Change TCP/IP Setting to WAN a. Use static IP(use of WISP subnet IP’s) b. Use Auto Negotiation for Speed c. Setting IP to WAN IP Setting i.e. IP Address, subnet Mask, Default Gateway d. DNS Server 1 use DNS’s IP 12. Click Apply Click Finish click “Save & Restart” and wait for 20sec for router restartBy Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 4 of 6
  5. 5. 13. Configure IP Scope for Sub Network and Verify your DHCP Server Setting 14. Click Apply Click Finish click “Save & Restart” and wait for 20sec for router restart 15. After the router was restart this how-to is completed! 16. Let’s begin Connect you clients Laptop, Smart Phone or PC to New subnet and Access internet You will get TCP/IP setting form your configure like per below a. Get Automatic TCP/IP Settingwith IP Address on 192.168.2.x /24 b. Default Gateway 192.168.2.1 c. DHCP, DNS Server 192.168.2.1 d. Take a look view basic network information when complete should look like below pictureBy Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 5 of 6
  6. 6. 1.4 Wireless Client Bridge Router CP E WISP AP WIFI WISPBy Wichets, Tel +66 89 8821501 | E-SPACE TECHNOLOGIES CORPORATION Rev 2.1 Pg. 6 of 6

×