Red Hat Installation Guide

198
-1

Published on

Red Hat Installation Guide

Published in: Education
0 Comments
1 Like
Statistics
Notes
  • Be the first to comment

No Downloads
Views
Total Views
198
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
0
Comments
0
Likes
1
Embeds 0
No embeds

No notes for slide

Red Hat Installation Guide

  1. 1. RED HATINSTALLATIONGUIDE
  2. 2. REDHAT INSTALL TUTORIAL STEP BY STEPThe installation process is chosen here uses the method of CD-ROM as the master filestorage media installation. To be able to install Redhat 9 Linux operating system from CD-ROM, the first step taken is to set the BIOS to boot from the CD-ROM. Toperform BIOS settings press the [DELETE] on the first computer when booting so thatthe display appears as follows:Figure 1. Computer BIOS Settings menuSelect Advanced BIOS Features menu that will display the BIOS settings as follows:Figure 2. Display Set Boot from CD2
  3. 3. Choose the boot sequence of the first computer from the CDROM as the image aboveand save the BIOS settings.After setting the BIOS insert CD # 1 Master Linux Redhat 9 and then restart thecomputer so the computer will boot from the CD-ROM. After the computer boot from theCD, it would appear the installation mode selection menu display as shown below:Figure 3. Installation Mode Selection Menu Redhat Linux 9In this menu there are 3 choices of installation mode with GUI or text-basedinstallation or option 3. To perform a text-based installation process to select thesecond by writing the Linux text and press the button <ENTER>After selecting the second option is a text mode, it will be brought to the installationmenu Redhat 9 to check the master installation CD that will be used as a masterinstallation. To check the CD master can be selected menu OK. If Redhat 9installation CD Master in good condition can be selected SKIP.Figure 4. Welcome Menu Installing Redhat Linux 9If you select OK then the system will check the installation CD Master is it still good orthere is damage. Checking process requires a long time depending on the read3
  4. 4. speed CDROM to the process of checking this master CD can be skipped so that itwill speed up the installation process.Figure 5. The process of checking CD Master Redhat Linux 9After completing the check or through checking of the CD menu, it would appear awelcome appearance as the following:Figure 6. The process of checking CD Master Redhat Linux 9In this menu there is only one option that is OK and should be selected by pressing thebutton <ENTER>4
  5. 5. Figure 7. Language Selection MenuSelect one language you master to do the installation process. As the default isEnglish.Figure 8. Menu Options Mouse Used Listen Read phonetically5
  6. 6. Figure 9. Menu Options Mouse UsedSystem installation will detect the mouse is used in accordance with that use.Incidentally at the time of installation to use the mouse PS / 2 scroll so that the display willappear as above.Figure 10. Searching for RedHat Linux Installations…Figure 11. Menu Options Functionality SystemsInstalling Red Hat Linux 9 provides a choice of 4 types of installation are as Personal6
  7. 7. Computers, as Workstation, As a Server or Custom. For a network operating systemthen choose as a server like the picture above.Figure 12. Menu Options Partition HarddiskIn Redhat Linux 9 installation, it takes a minimum of disk partition into 2, namely for /root and swap. To create a partition can be either automatic or manually.Figure 13. Hard Disk Partition Creation Menu ConfirmationIf you already have a hard drive partition that is used with other formats such as Fat 16for Windows 97, Fat 32 for win 98, ME or NTFS for Win XP, 2000 and NT, then you canmaintain the previous partition by selecting the option Keep the all partition anduseexisting freespace.Options Remove all partition on this system will delete all partitions on the hard disk sothat all data will be lost. If the hard drive is used to perform the installation is emptyyou should select this menu.7
  8. 8. Figure 14. Failure to Make Partition Error MessagesFigure 15. Error Messages Automatically Partition FailureIf youre having disk partition creation process fails, then the partitioning process can berepeated by returning to the previous menu.Figure 16. Making Menu With Manually Partition Disk DruidDisk partition process can be done manually with disk facility druids like in thepicture above. With the DiskDruidartitioning can be made as needed.8
  9. 9. Figure 17. Making Menu With Manually Partition Disk DruidIn the picture above shows that the hard drive partition that is used has had as many as3, ie each using the NTFS format. To create a new partition menu select [NEW], tochange the format the partition select the [EDIT], and to delete existing partitionsselect [DELETE].Figure 18. Manually partition with Disk DruidFigure 19. Menu Options Manually Partition with Disk Druid9
  10. 10. Figure 20. Settings Manually Partition with Disk DruidFigure 21. Settings Manually Partition with Disk DruidOnce you make a disk partition process then the result will look like the picture abovethe minimum consists of 2 main partition ie / root and swap. In the installation ofLinux-based operating system partitions that are typically used quite a lot that is /root, / boot, / home, / var, / usr and swap.After the partitioning process is done either automatically or manually, then the nextprocess is the selection of Boot Loader.Boot loader is the first software that runs when the computer was first turned on. Thissoftware is functioning at the time of loading and transfer control to operate thesystem software kernel.Setting the boot loader has an important role to be installed if the computer hasanother operating system then can choose which operating system to be used. Redhat 9provides two software boot loader is GRUB and LILO.10
  11. 11. Figure 22. Boot Loader ConfigurationRedhat Linux operating system requires a network configuration settings. The installationprogram will automatically detect the appropriate type of network devices. Next enterthe IP address and netmask.Sample numbering IP Address is 192.168.10.100 As for Subnetmask 255.255.255.0Setting the IP Address and Subnet Mask should be adjusted to the LAN configurationconstructed for each computer to work properly.Figure 23. Network ConfigurationFire Wall ConfigurationIn order to improve computer security at the network, Red Hat Linux provides FirewallProtection. We can choose the security level that desired like in the picture above.11
  12. 12. Figure 24. Firewall ConfigurationHere is provided 3 levels of security• HighThis security level only allows connections in accordance with defult settings sothat only can connect with the DNS replies and DHCP• MediumLevel mediium provide limitations in connection to a particular source system.• No FirewallSelection No firewall security level can be done if it is satisfied that systems arein a network that can be trusted.• TimingThe timing must be done for the time indicated on the computer accordingto the place where the computer is placed.Figure 25. Configuration Time• User SettingsAfter the installation process will display the password setting root (networkadministrator). In this process required setting the root password (administrator).This process is very important in network operating systems because only at thislevel of total access rights can be done.12
  13. 13. Besides the root, can also add users that can use this system with a password as a user.Figure 26. Root Password ConfigurationHaving determined the root password the next step is the process of copying thenecessary files to the hard drive until the installation is finished with a marked displaystating that the installation process has completed.13

×