Transcript of "Connecting interactive white_board"
RM Classboard TouchWith Bluetooth Connectivity
PolyVision following computerWhite Board Works with the Interactive configurations: Mac PC with Built in Bluetooth PC with no built in BluetoothMain benefits of the Bluetooth White Board: No cable required to connect the board to the computer.
Caring for your PolyVision Board DO NOT UNDER ANY CIRCUMSTANCES USE DRY ERASE CLEANER ON THE BOARD’S SURFACE. The board is cleaned by using soap and water mixture. If you write on the board use only dry erase markers and clean the board that day to insure you board will last. The board has a five year warranty from RM.
Installing the RM Classboard Bluetooth Bluetooth is held in place by two screws.The RM installers should have connected this during installation.
Loading the PolyVision Software You must have administrative rights to load the software. Use the Polyvision disk that comes in the Polyvision box or Use the Polyvision software from the Web Site http://www.polyvision.com/Support/Downloads/tabid/232/CategoryId/18/DownloadTypeId/106/LangId/158/Default.aspx Choose Mac or PC
Downloading the PolyVision Drivers Once drivers have been loaded, turn off the computer completely. Leave computer shut down for two minutes. Insert the Polyvision Bluetooth into one of your computer’s USB ports. Turn on computer with Bluetooth inserted in the USB port.
Stop and Read Below:If you have a PC, please continue to the next slide for directions onwhiteboard connectivity. If you have a MAC please continue to the NEXTStop Sign in this presentation for connecting using your MAC computer.
Required Bluetooth Setting on Laptops On the “Start” toolbar bar, chose the Control Panel. Once in Control Panel, chose Administrative Tools.
Required Bluetooth Setting onLaptops Choose Services Shortcut.
Required Bluetooth Setting onLaptops Select Bluetooth Support Services.
Required Bluetooth Setting onLaptops On the General tab, hit the stop button.
Required Bluetooth Setting onMove to the Log On Tab, make sure to Go back to the General Tab and hit theLaptopschose LOCAL SYSTEM ACCOUNT. START button.
Connecting to the POLYVISION Adapter to the Classboard Bluetooth- PC DirectionsNow that you the Classboard drivers dowloaded, you areready to connect the board with your computer. Give yourcomputer a chance to recognize the Polyvision bluetooth.You will see this icon pop up in the system tray.Step 1: Right click on the Bluetooth icon in the system tray on your desktop.Step 2: A similar menu will pop up, please select Add Bluetooth Device.
Connectingwill appear, follow directions below: Step 3: This screen to the POLYVISIONAdapter- PC Directions Select the device is ready to be setup and hit the NEXT button.
Connecting to the POLYVISION Step 4: Choose the PV device and follow directions below:Adapter- PC Directions Select and hit the next button
Connecting to the POLYVISIONStep 5: Select the Use Passkey found in documentation and type in thepasscode 1,2,3,4 and hit next. Adapter- PC Directions Passcode is 1, 2, 3,4 Hit next after entering code.
Connecting to the POLYVISIONStep 6: The computer will connect to the RM Classboard Bluetooth . Adapter- PC Directions
Connecting to the POLYVISIONAdapter- PC DirectionsFinal Step: Your Bluetooth is now configured and ready to be used. Click on the finish button.
Configuring the POLYVISION Driver-PC Directions Step 1: Click on the Polyvision board short cut and choose the “Configure Polyvision Driver tab.”
RM Classboard Configuration Preferences- PC DirectionsShort-cut to the board drivercan be found on the desktop to accessthe configuration. Click to launchconfiguration options. Choose the “best” selection on the “projection” tab. This will give you the best calibration.
Connecting to the POLYVISIONAdapter to the ClassboardBluetooth- PC Directions Final step is to connect the whiteboard by clicking the “find serial whiteboard button.” Once the board is connected you will hear the board “chirp.” Now hit the projector button on the board short cuts and this will take you to the calibration screen.
Connecting the POLYVISION Adapter to theIWB Bluetooth- PC DirectionsAfter you go through the previous steps one time, youshould automatically connect to the board as long asyour Polyvision Bluetooth Adapter is inserted in yourcomputer…every time you turn on the board, it willautomatically connect with the “chirp.”Then you hit the projection button and the board is readyto use.
Calibrating the PolyVision Boards Hit the projection short cut button on the board this green calibration screen will pop up. Hit each target to ensure perfect calibration.