Chapter 6:
Topologies and Access Methods
Network+ Guide to Networks
2
Objectives
Describe the basic and hybrid LAN physical
topologies, and their uses, advantages, and
disadvantages
Descri...
3
Objectives (continued)
Understand the transmission methods
underlying Ethernet, LocalTalk, Token Ring,
FDDI, and ATM ne...
4
Simple Physical Topologies
• Physical topology is the physical layout,
or pattern, of the nodes on a network
• Physical ...
5
Simple Physical Topologies
(continued)
• Bus
• A bus topology consists of a single cable
connecting all nodes on a netwo...
6
• Ring
• In a ring topology, each node is connected to the
two nearest nodes so that the entire network
forms a circle
•...
7
• In a star topology, every node on the
network is connected through a central
device, such as a hub or switch
• Star to...
8
• Star-Wired Ring
• The star-wired ring topology uses the physical
layout of a star in conjunction with the ring
topolog...
9
• In a star-wired bus topology, groups of
workstations are star-connected to hubs
and then networked via a single bus
• ...
10
• More expensive than using either the star or,
especially, the bus topology alone because it
requires more cabling and...
11
Backbone Networks
• A network backbone is the cabling that connects
the hubs, switches, and routers on a network
• Back...
12
Backbone Networks (continued)
• In networking, the term enterprise refers to an
entire organization, including its loca...
13
• Serial Backbone
• The simplest kind of backbone
• It consists of two or more internetworking devices
connected to eac...
14
• Distributed Backbone
• Consists of a number of connectivity devices connected
to a series of central connectivity dev...
15
• A more complicated distributed backbone connects
multiple LANs or LAN segments using routers
• Provides network admin...
16
• Collapsed Backbone
• Uses a router or switch as the single central
connection point for multiple subnetworks
• A sing...
17
• Parallel Backbone
• The most robust type of network backbone
• The most significant advantage of using a parallel
bac...
18
Logical Topologies
• Logical topology refers to the way in which data is
transmitted between nodes
• The most common lo...
19
Switching
• A component of a network’s logical topology that
determines how connections are created between
nodes
• The...
20
• Circuit Switching
• A connection is established between two network
nodes before they begin transmitting data
• Bandw...
21
• Message Switching
• Establishes a connection between two devices,
transfers the information to the second device, and...
22
• This “store and forward” routine continues until the
message reaches its destination
• Message switching requires tha...
23
• Packet Switching is the most popular
method for connecting nodes on a
network
• Breaks data into packets before they ...
24
Ethernet
• Carrier Sense Multiple Access with
Collision Detection (CSMA/CD)
• The access method used in Ethernet
• The ...
25
Ethernet (continued)
• The term “Multiple Access” refers to the fact that several
Ethernet nodes can be connected to a ...
26
• The NIC will issue a special 32-bit sequence that
indicates to the rest of the network nodes that the
its previous tr...
27
• Switched Ethernet
• Traditional Ethernet LANs, called shared Ethernet,
supply a fixed amount of bandwidth that must b...
28
• Ethernet Frames
• Ethernet networks may use one (or a combination)
of four kinds of data frames: Ethernet_802.2
(“Raw...
29
• Using and Configuring Frames
• You can use multiple frame types on a network, but
you cannot expect interoperability ...
30
• The preamble signals to the receiving node that
data is incoming and indicates when the data flow
is about to begin
•...
31
• Each Ethernet frame also contains a 14-byte header,
which includes a destination address, a source
address, and an ad...
32
• Ethernet_II frame type contains a 2-byte type field.
This type field identifies the Network layer protocol
(such as I...
33
• Power over Ethernet
• Recently, IEEE has finalized a new standard,
802.3af, that specifies a method for supplying
ele...
34
LocalTalk
• LocalTalk is a network access method designed by
Apple Computer, Inc. specifically for networking
Macintosh...
35
Token Ring
• A network technology first developed by IBM in the
1980s
• Token Ring networks have traditionally been mor...
36
• Token Ring Switching
• Token Ring networks can take advantage of
switching to better utilize limited bandwidth
• A To...
37
• Token Ring Frames
• Token Ring networks may use one of two
types of frames: the IEEE 802.5 or the IBM
Token Ring fram...
38
• A network technology whose standard was originally
specified by ANSI in the mid-1980s and later refined
by ISO
• FDDI...
39
Asynchronous Transfer Mode (ATM)
• An ITU networking standard describing Data Link layer
protocols for both network acc...
40
ATM (continued)
• Establishing a reliable connection allows ATM to
guarantee a specific Quality of Service (QoS) for
ce...
41
Wireless Networks
• Each wireless technology is defined by a standard
that describes unique functions at both the
Physi...
42
• 802.11 Another name for Wireless Local
Area Networks (WLAN) standards
committee
• Access Method
• 802.11 standards sp...
43
• Association
• In the context of wireless networking,
communication that occurs between a station and
an access point ...
44
• There are two types of scanning: active and passive
• In active scanning, the station transmits a special
frame, know...
45
• Frames
• For each function, the 802.11 standard specifies a
frame type at the MAC sublayer
• These multiple frame typ...
46
• 802.11b
• Also known as “Wi-Fi,” for Wireless Fidelity
• Uses direct sequence spread spectrum (DSSS)
signaling
• 802....
47
• 802.11a
• 802.11a’s high throughput is attributable to its use
of higher frequencies, its unique method of
encoding d...
48
• 802.11g
• 802.11g benefits from being compatible with 802.11b
networks
• 802.11g has high throughput
• 802.11g’s comp...
49
• Bluetooth
• Bluetooth is a mobile wireless networking standard
that uses DSSS signaling in the 2.4-GHz band to
achiev...
50
• HomeRF
• HomeRF is a wireless networking specification
developed by the HomeRF Working Group
• The most unique aspect...
51
Summary
• Basic and hybrid LAN physical topologies,
and their uses, advantages, and
disadvantages
• Describe the backbo...
52
Summary (continued)
• Transmission methods underlying
Ethernet, LocalTalk, Token Ring, FDDI,
and ATM networks
• Charact...
Upcoming SlideShare
Loading in...5
×

Chapter06 -- topologies and access methods

1,509

Published on

Basic Networking Guide

Published in: Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
1,509
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
61
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Chapter06 -- topologies and access methods

  1. 1. Chapter 6: Topologies and Access Methods Network+ Guide to Networks
  2. 2. 2 Objectives Describe the basic and hybrid LAN physical topologies, and their uses, advantages, and disadvantages Describe the backbone structures that form the foundation for most LANs Compare the different types of switching used in data transmission
  3. 3. 3 Objectives (continued) Understand the transmission methods underlying Ethernet, LocalTalk, Token Ring, FDDI, and ATM networks Describe the characteristics of different wireless network technologies, including the three IEEE 802.11 standards
  4. 4. 4 Simple Physical Topologies • Physical topology is the physical layout, or pattern, of the nodes on a network • Physical topologies are divided into three fundamental geometric shapes: bus, ring, and star
  5. 5. 5 Simple Physical Topologies (continued) • Bus • A bus topology consists of a single cable connecting all nodes on a network without intervening connectivity devices • The single cable is called the bus and can support only one channel for communication • Most bus networks use coaxial cable as their physical medium • At the ends of each bus network are 50-ohm resistors known as terminators
  6. 6. 6 • Ring • In a ring topology, each node is connected to the two nearest nodes so that the entire network forms a circle • Data is transmitted clockwise, in one direction (unidirectional), around the ring • The fact that all workstations participate in delivery makes the ring topology an active topology • A ring topology also differs in that it has no “ends” and data stops at its destination and, twisted-pair or fiber-optic cabling is used as the physical medium22 Simple Physical Topologies (continued)
  7. 7. 7 • In a star topology, every node on the network is connected through a central device, such as a hub or switch • Star topologies are usually built with twisted-pair or fiber-optic cabling • Star topologies require more cabling than ring or bus networks • Each node is separately connected to a central connectivity device, they are more fault-tolerant Simple Physical Topologies (continued)
  8. 8. 8 • Star-Wired Ring • The star-wired ring topology uses the physical layout of a star in conjunction with the ring topology’s data transmission method • Data is sent around the star in a circular pattern • This hybrid topology benefits from the fault tolerance of the star topology Hybrid Physical Topologies
  9. 9. 9 • In a star-wired bus topology, groups of workstations are star-connected to hubs and then networked via a single bus • With this design, you can cover longer distances and easily interconnect or isolate different network segments Hybrid Physical Topologies (continued)
  10. 10. 10 • More expensive than using either the star or, especially, the bus topology alone because it requires more cabling and potentially more connectivity devices • The star-wired bus topology forms the basis for modern Ethernet and Fast Ethernet networks Hybrid Physical Topologies (continued)
  11. 11. 11 Backbone Networks • A network backbone is the cabling that connects the hubs, switches, and routers on a network • Backbones usually are capable of more throughput than the cabling that connects workstations to hubs
  12. 12. 12 Backbone Networks (continued) • In networking, the term enterprise refers to an entire organization, including its local and remote offices, a mixture of computer systems, and a number of departments • The backbone is the most significant building block of enterprise-wide networks
  13. 13. 13 • Serial Backbone • The simplest kind of backbone • It consists of two or more internetworking devices connected to each other by a single cable in a daisy-chain fashion • In networking, a daisy chain is simply a linked series of devices • Hubs and switches are often connected in a daisy chain to extend a network Backbone Networks (continued)
  14. 14. 14 • Distributed Backbone • Consists of a number of connectivity devices connected to a series of central connectivity devices such as hubs, switches, or routers, in a hierarchy • This kind of topology allows for simple expansion and limited capital outlay for growth, because more layers of devices can be added to existing layers Backbone Networks (continued)
  15. 15. 15 • A more complicated distributed backbone connects multiple LANs or LAN segments using routers • Provides network administrators with the ability to segregate workgroups and therefore manage them more easily Backbone Networks (continued)
  16. 16. 16 • Collapsed Backbone • Uses a router or switch as the single central connection point for multiple subnetworks • A single router or switch is the highest layer of the backbone6 • The router or switch that makes up the collapsed backbone must contain multiprocessors to handle the heavy traffic going through it • This arrangement allows you to interconnect different types of subnetworks Backbone Networks (continued)
  17. 17. 17 • Parallel Backbone • The most robust type of network backbone • The most significant advantage of using a parallel backbone is that its redundant (duplicate) links ensure network connectivity to any area of the enterprise • Parallel backbones are more expensive than other enterprise-wide topologies • They make up for the additional cost by offering increased performance and better fault tolerance Backbone Networks (continued)
  18. 18. 18 Logical Topologies • Logical topology refers to the way in which data is transmitted between nodes • The most common logical topologies are bus and ring • In a bus logical topology, signals travel from one network device to all other devices on the network • In a ring logical topology signals follow a circular path between sender and receiver • Logical topologies is useful when troubleshooting and designing networks
  19. 19. 19 Switching • A component of a network’s logical topology that determines how connections are created between nodes • There are three methods for switching: circuit switching, message switching, and packet switching
  20. 20. 20 • Circuit Switching • A connection is established between two network nodes before they begin transmitting data • Bandwidth is dedicated to this connection and remains available until the users terminate communication between the two nodes • While the nodes remain connected, all data follows the same path initially selected by the switch Switching (continued)
  21. 21. 21 • Message Switching • Establishes a connection between two devices, transfers the information to the second device, and then breaks the connection • The information is stored and forwarded from the second device once a connection between that device and a third device on the path is established Switching (continued)
  22. 22. 22 • This “store and forward” routine continues until the message reaches its destination • Message switching requires that each device in the data’s path have sufficient memory and processing power to accept and store the information before passing it to the next node Switching (continued)
  23. 23. 23 • Packet Switching is the most popular method for connecting nodes on a network • Breaks data into packets before they are transported • Packets can travel any path on the network to their destination • When packets reach their destination node, the node reassembles them based on their control information • Does not waste bandwidth by holding a connection open until a message reaches its destination Switching (continued)
  24. 24. 24 Ethernet • Carrier Sense Multiple Access with Collision Detection (CSMA/CD) • The access method used in Ethernet • The term “Carrier Sense” refers to the fact that Ethernet NICs listen on the network and wait until they detect (or sense) that no other nodes are transmitting data over the signal (or carrier) on the communications channel before they begin to transmit
  25. 25. 25 Ethernet (continued) • The term “Multiple Access” refers to the fact that several Ethernet nodes can be connected to a network and can monitor traffic, or access the media, simultaneously • The last part of the term CSMA/CD, “collision detection,” refers to the way nodes respond to a collision • When two transmissions interfere with each other; this is known as a collision
  26. 26. 26 • The NIC will issue a special 32-bit sequence that indicates to the rest of the network nodes that the its previous transmission was faulty and that those data frames are invalid which is called jamming • A collision domain is the portion of a network in which collisions occur if two nodes transmit data at the same time • A data propagation delay is the length of time data takes to travel from one point on the segment to another point Ethernet (continued)
  27. 27. 27 • Switched Ethernet • Traditional Ethernet LANs, called shared Ethernet, supply a fixed amount of bandwidth that must be shared by all devices on a segment, and all nodes on that segment belong to the same collision domain • Switched Ethernet enables multiple nodes to simultaneously transmit and receive data over different logical network segments • Using switched Ethernet increases the effective bandwidth of a network segment because fewer workstations must vie for the same time on the wire Ethernet (continued)
  28. 28. 28 • Ethernet Frames • Ethernet networks may use one (or a combination) of four kinds of data frames: Ethernet_802.2 (“Raw”), Ethernet_802.3 (“Novell proprietary”), Ethernet_II (“DIX”), and Ethernet_SNAP • Each frame type differs slightly in the way it codes and decodes packets of data traveling from one device to another Ethernet (continued)
  29. 29. 29 • Using and Configuring Frames • You can use multiple frame types on a network, but you cannot expect interoperability between the frame types • Frame types are typically specified through a device’s NIC configuration software • Most NICs can automatically sense what types of frames are running on a network and adjust themselves to that specification which is a feature is called autodetect, or autosense Ethernet (continued)
  30. 30. 30 • The preamble signals to the receiving node that data is incoming and indicates when the data flow is about to begin • The start-of-frame delimiter (SFD) identifies where the data field begins Ethernet (continued)
  31. 31. 31 • Each Ethernet frame also contains a 14-byte header, which includes a destination address, a source address, and an additional field that varies in function and size, depending on the frame type • The extra bytes are known as padding and have no significance other than to fill out the frame • Ethernet_II (“DIX”) and Ethernet_SNAP • An Ethernet frame type developed by DEC, Intel, and Xerox (abbreviated as DIX) before the IEEE began to standardize Ethernet Ethernet (continued)
  32. 32. 32 • Ethernet_II frame type contains a 2-byte type field. This type field identifies the Network layer protocol (such as IP,ARP, RARP, or IPX) contained in the frame • The Ethernet_SNAP standard calls for additional control fields • Ethernet_SNAP frames allow less room for data Ethernet (continued)
  33. 33. 33 • Power over Ethernet • Recently, IEEE has finalized a new standard, 802.3af, that specifies a method for supplying electrical power over Ethernet connections, also known as Power over Ethernet (PoE) • The PoE standard specifies two types of devices: power sourcing equipment (PSE) and powered devices (PDs) • Power sourcing equipment (PSE) • Powered devices (PDs) Ethernet (continued)
  34. 34. 34 LocalTalk • LocalTalk is a network access method designed by Apple Computer, Inc. specifically for networking Macintosh computers • It provided a simple, cost-effective way of interconnecting Macintosh devices • LocalTalk uses a transmission method called Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) • LocalTalk relies on the AppleTalk protocol, but it may also support the Macintosh version of TCP/IP called MacTCP
  35. 35. 35 Token Ring • A network technology first developed by IBM in the 1980s • Token Ring networks have traditionally been more expensive to implement than Ethernet networks • The 100-Mbps Token Ring standard, finalized in 1999, is known as High-Speed Token Ring (HSTR) • In token passing, a 3-byte packet, called a token, is transmitted from one node to another in a circular fashion around the ring • The active monitor maintains the timing for ring passing
  36. 36. 36 • Token Ring Switching • Token Ring networks can take advantage of switching to better utilize limited bandwidth • A Token Ring switch can subdivide a large network ring into several smaller network rings • Token Ring technology does not allow collisions Token Ring (continued)
  37. 37. 37 • Token Ring Frames • Token Ring networks may use one of two types of frames: the IEEE 802.5 or the IBM Token Ring frame • Every Token Ring frame includes Start Delimiter (SD), Access Control (AC), and End Delimiter (ED) fields • Token Ring frames use a Frame Status (FS) to provide low-level acknowledgment that the frame was received whole Token Ring (continued)
  38. 38. 38 • A network technology whose standard was originally specified by ANSI in the mid-1980s and later refined by ISO • FDDI (pronounced “fiddy”) uses a double ring of multimode or single mode fiber to transmit data at speeds of 100 Mbps • FDDI is more reliable and more secure than transmission methods that depend on copper wiring • FDDI works well with Ethernet 100BaseTX technology • FDDI technology has a high cost relative to Fast Ethernet Fiber Distributed Data Interface (FDDI)
  39. 39. 39 Asynchronous Transfer Mode (ATM) • An ITU networking standard describing Data Link layer protocols for both network access and signal multiplexing • ATM may run over fiber-optic or CAT 5 or higher UTP or STP cable • In ATM, a packet is called a cell and always consists of 48 bytes of data plus a 5-byte header • ATM technology is that it relies on virtual circuits • ATM a connection-oriented technology using virtual circuits
  40. 40. 40 ATM (continued) • Establishing a reliable connection allows ATM to guarantee a specific Quality of Service (QoS) for certain transmissions • QoS is a standard that specifies that data will be delivered within a certain period of time after it is sent • ATM networks can be integrated with Ethernet or Token Ring networks through the use of LAN Emulation (LANE)
  41. 41. 41 Wireless Networks • Each wireless technology is defined by a standard that describes unique functions at both the Physical and the Data Link layers of the OSI Model • These standards differ in their specified signaling methods, geographic ranges, and frequency usages, among other things. • The most popular wireless standards used on contemporary LANs are those developed by IEEE’s 802.11 committee
  42. 42. 42 • 802.11 Another name for Wireless Local Area Networks (WLAN) standards committee • Access Method • 802.11 standards specify the use of Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) to access a shared medium • Use of ACK packets to verify every transmission • RTS/CTS enables a source node to issue an RTS signal to an access point requesting the exclusive opportunity to transmit Wireless Networks (continued)
  43. 43. 43 • Association • In the context of wireless networking, communication that occurs between a station and an access point to enable the station to connect to the network via that access point • As long as a station is on and has its wireless protocols running, it periodically surveys its surroundings for evidence of an access point, a task known as scanning Wireless Networks (continued)
  44. 44. 44 • There are two types of scanning: active and passive • In active scanning, the station transmits a special frame, known as a probe, on all available channels within its frequency range • In passive scanning, a wireless station listens on all channels within its frequency range for a special signal, known as a beacon frame, issued from an access point • Service Set Identifier (SSID), a unique character string used to identify an access point • A station might choose a different access point through a process called re-association Wireless Networks (continued)
  45. 45. 45 • Frames • For each function, the 802.11 standard specifies a frame type at the MAC sublayer • These multiple frame types are divided into three groups: management, control and data • Management frames are those involved in association and re-association, such as the probe and beacon frames • Control frames are those related to medium access and data delivery, such as the ACK and RTS/CTS frames • Data frames are those that carry the data sent between stations Wireless Networks (continued)
  46. 46. 46 • 802.11b • Also known as “Wi-Fi,” for Wireless Fidelity • Uses direct sequence spread spectrum (DSSS) signaling • 802.11b was the first to take hold and remains the most popular • It is also the least expensive of all the 802.11 WLAN technologies Wireless Networks (continued)
  47. 47. 47 • 802.11a • 802.11a’s high throughput is attributable to its use of higher frequencies, its unique method of encoding data, and more available bandwidth • Higher frequency signals require more power to transmit and travel shorter distances than lower frequency signals • The additional access points, as well as the nature of 802.11a equipment, make this standard more expensive than either 802.11b or 802.11g Wireless Networks (continued)
  48. 48. 48 • 802.11g • 802.11g benefits from being compatible with 802.11b networks • 802.11g has high throughput • 802.11g’s compatibility with the more established 802.11b has caused many network managers to choose it over 802.11a, despite 802.11a’s comparative advantages • Laptops could roam between the ranges of the 802.11b and 802.11g access points without an interruption in service Wireless Networks (continued)
  49. 49. 49 • Bluetooth • Bluetooth is a mobile wireless networking standard that uses DSSS signaling in the 2.4-GHz band to achieve a maximum theoretical throughput of 1 Mbps • Bluetooth was designed to be used on small networks composed of personal communications devices, also known as personal area networks (PANs) • Bluetooth’s low throughput and short range makes it impractical for business LANs. Wireless Networks (continued)
  50. 50. 50 • HomeRF • HomeRF is a wireless networking specification developed by the HomeRF Working Group • The most unique aspect of the HomeRF standard is that it was designed to allow both traditional telephone signals and data signals to be exchanged over the same wireless network • Its working group was disbanded in January 2003 Wireless Networks (continued)
  51. 51. 51 Summary • Basic and hybrid LAN physical topologies, and their uses, advantages, and disadvantages • Describe the backbone structures • Compared the different types of switching used in data transmission
  52. 52. 52 Summary (continued) • Transmission methods underlying Ethernet, LocalTalk, Token Ring, FDDI, and ATM networks • Characteristics of different wireless network technologies, including the three IEEE 802.11 standards
  1. A particular slide catching your eye?

    Clipping is a handy way to collect important slides you want to go back to later.

×