This document provides an overview of IPv6 addressing and key concepts. It defines IPv6, discusses the benefits of its larger 128-bit address space, and covers address types including unicast, multicast, and anycast. The document also describes IPv6 address formatting and allocation, interface identifier mapping, autoconfiguration, and renumbering capabilities. Concepts are explained through examples and comparisons to IPv4 addressing.
2. Before we start…
_____ IPng _____
_____ IPv6 _____
_____ CIDR _____
_____ NAT _____
_____ Autoconfiguration_____
_____ Unicast _____
_____ Multicast _____
_____ Anycast _____
_____ IPv4-Compatible _____
_____ IANA _____
_____ VLSM _____
_____ ICANN _____
_____ Dual-Stack _____
_____ Tunneling _____
_____ Translation _____
_____ Node _____
_____ Packet _____
Please write down the following Key Terms on a blank piece of paper leaving a small
underline before and after each word. Label your paper IPv6 Pre/Post Concept Check.
3. Pre Check of Knowledge
1. Rate yourself as to your perceived knowledge
of these key words.
2. Assess how much you already know about
these terms by placing a (+), a check (√), or a
zero (0) in the space to the left of each word.
Plus (+) = Expert
Check (√) = Heard of it
Zero (0) = Have not heard of it.
We will do a Post Check at the end of this chapter.
4. 4
1- Overview
IPv6 Defined
Internet Protocol version 6
Originally known as IPng, or IP Next Generation
Network Layer protocol for packet switched
networks
Successor of IPv4 which supports about 4.3 billion
addresses (232 addresses)
IPv6 increased the number of addresses to (2128
addresses)
5. Benefits
IPv6 longer address length is needed for:
Routing Aggregation
Autoconfiguration of Addresses
Easier allocation of address blocks
Flexibility of ISPs to subdivide blocks for
customers
Organizations can subdivide blocks for internal
networks
Embedded Quality of Service (QoS) to support
services like VoIP & IP Video
Improved scalability for multicast routing
More efficient packet forwarding
6. Okay, so what happened to
IPv5?
IPv5 was NOT a successor to IPv6
Known as Internet ST (Stream Protocol)
Experimental protocol….Not in public use
7. What’s driving the need for
IPv6??
Internet growth
Mobile devices
PDAs
Mobile phones
Tablet PCs
Gaming
Voice/Video
Security Monitoring
Appliances
Medical Imaging
Animal Tags
Media Services
Traffic Control
Planes
Automobiles
Hotspots
8. 8
2- INTRODUCTION
What is the IPv6 address?
An IPv6 address is 128 bits or 16 bytes (8 octets) long
as shown in this figure. The address length in IPv6 is
four times the length address in IPv4.
10. 10
Show the unabbreviated colon hex notation for the following IPv6
addresses:
a. An address with 64 0s followed by 64 1s.
b. An address with 128 0s.
c. An address with 128 1s.
d. An address with 128 alternative 1s and 0s.
Solution
a. 0000:0000:0000:0000:FFFF:FFFF:FFFF:FFFF
b. 0000:0000:0000:0000:0000:0000:0000:0000
c. FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF
d. AAAA:AAAA:AAAA:AAAA:AAAA:AAAA:AAAA:AAAA
Example 1
11. 11
The following shows the zero contraction version of addresses in
Example 1 (part c and d cannot be abbreviated)
a. :: FFFF:FFFF:FFFF:FFFF
b. ::
c. FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF
d. AAAA:AAAA:AAAA:AAAA:AAAA:AAAA:AAAA:AAAA
Example 2
12. 12
Show abbreviations for the following addresses:
a. 0000:0000:FFFF:0000:0000:0000:0000:0000
b. 1234:2346:0000:0000:0000:0000:0000:1111
c. 0000:0001:0000:0000:0000:0000:1200:1000
d. 0000:0000:0000:0000:0000:FFFF:24.123.12.6
Example 3
Solution:
a. 0:0:FFFF::
b. 1234:2346::1111
c. 0:1::1200:1000
d. ::FFFF:24.123.12.6
13. 13
Decompress the following addresses and show the complete
unabbreviated IPv6 address:
a. 1111::2222
b. ::
c. 0:1::
d. AAAA:A:AA::1234
Solution
a. 1111:0000:0000:0000:0000:0000:0000:2222
b. 0000:0000:0000:0000:0000:0000:0000:0000
c. 0000:0001:0000:0000:0000:0000:0000:0000
d. AAAA:000A:00AA:0000:0000:0000:0000:1234
Example 4
14. IPv6 Number of Addresses
To give some idea about the number of IPv6
addresses, let us assume that the number of people
on the planet earth is soon to be 234 (more than 16
billion). Each person can have 294 addresses to use.
If we assign 260 addresses to the users each year
(almost one billion each second), it takes 268 years
to deplete addresses.
15. 15
3- ADDRESS SPACE ALLOCATION
• Like the address space of IPv4, the address space of IPv6 is divided into
several blocks of varying size and each block is allocated for special
purpose.
• Most of the blocks are still unassigned and have been left aside for future
use.
• To better understand the allocation and the location of each block in
address space, we first divide the whole address space into eight equal
ranges.
• This division shows where each actual block is located .
17. 17
Compare the unspecified address in IPv4 to the unspecified
addresses in IPv6.
Solution
In both architectures, an unspecified address is an all-zero
address. In IPv4 this address is part of class A address; in IPv6
this address is part of the reserved block.
Example 5
19. 19
Compare the loop addresses in IPv4 to the loopback address in
IPv6.
Solution
There are two differences in this case. In classful addressing, a
whole block is allocated for loopback addresses; it is the
127.0.0.0/8 - 127.255.255.255 , in IPv6 only one address is
allocated as the loopback address; it is the ::1/128. In addition, the
loopback block in classful addressing is part of the class A block. In
IPv6, it is only one single address in the reserved block.
You can find more about IP Reserved, Loopback and Private
Addresses by visiting this website:
http://www.tcpipguide.com/free/t_IPReservedPrivateandLoopback
Addresses-3.htm
Example 6
21. 21
The Three Levels of Hierarchy
Global Routing Prefix (48 bits) is like the network ID in IPv4
22. 22
Mapping for EUI (Extended Unique Identifier)-64
• One of IPv6's key benefits over IPv4 is its capability for
automatic interface addressing.
• By implementing the IEEE's 64-bit Extended Unique
Identifier (EUI-64) format, a host can automatically assign
itself a unique 64-bit IPv6 interface identifier without the
need for manual configuration or DHCP.
• This is accomplished on Ethernet interfaces by referencing the
already unique 48-bit MAC address, and reformatting that
value to match the EUI-64 specification.
23. This can be described as having two steps:
The first step is to convert the 48-bit MAC
address to a 64-bit value. To do this, we
break the MAC address into its two 24-bit
halves: the Organizationally Unique
Identifier (OUI) and the NIC specific part.
The 16-bit hex value FFFE is then inserted
between these two halves to form a 64-bit
address.
Why FFFE? this is a reserved value which
equipment manufacturers cannot include in
"real" EUI-64 address assignments. In other
words, any EUI-64 address having FFFE
immediately following its OUI portion can
be recognized as having been generated
from an EUI-48 (or MAC) address.
23
Mapping for Ethernet MAC
24. 24
Find the interface identifier if the Ethernet physical address is (F5-
A9-23-14-7A-D2)16 using the format we defined for Ethernet
addresses.
Solution
We only need to change the seventh bit of the first octet from 0 to
1, insert two octet FFFE and change the format to colon hex
notation. The result is F7A9:23FF:FE14:7AD2 in colon hex.
Example 7
25. 25
An organization is assigned the block 2000:1456:2474/48. What is
the CIDR notation for the blocks in the first and second subnets in
this organization?
Solution
Theoretically, the first and second subnets should use the block
with subnet identifier 000116 and 000216. This means that the
blocks are
2000:1456:2474:0001/64
and
2000:1456:2474:0002/64.
Example 8
26. 26
An organization is assigned the block 2000:1456:2474/48. What is
the IPv6 address of an interface in the third subnet if the IEEE
physical address of the computer is (F5-A9-23-14-7A-D2)16.
Solution
The interface identifier is F7A9:23FF:FE14:7AD2 (see Example 7). If
we add this identifier to the global prefix and the subnet identifier,
we get:
Example 9
27. 27
4- AUTOCONFIGURATION
• One of the interesting features of IPv6 addressing is
the autoconfiguration of hosts.
• As we discussed in IPv4, the host and routers are
originally configured manually by the network
manager using static addresses, however, the
Dynamic Host Configuration Protocol, DHCP, can
also be used to allocate an IPv4 address to a host
that joins the network.
• In IPv6, DHCP protocol can still be used to allocate
an IPv6 address to a host, but a host can also
configure itself.
28. 28
Assume a host with Ethernet address (F5-A9-23-11-9B-E2)16 has
joined the network. What would be its global unicast address if the
global unicast prefix of the organization is 3A21:1216:2165 and the
subnet identifier is 1232 ?
Solution
The host first creates its interface identifier as
F7A9:23FF:FE11:9BE2
using the Ethernet MAC address read from its NIC card.
Assuming that this address is unique, the host sends a router
solicitation message and receives the router advertisement
message that announces the combination of global unicast prefix
and the subnet identifier as 3A21:1216:2165:1232. The host then
appends its interface identifier to this prefix to find and store its
global unicast address as:
Example 10
3A21:1216:2165:1232:F7A9:23FF:FE11:9BE2
29. 29
5- RENUMBERING , ADDRESS TYPES
and MIGRATION
• To allow sites to change the service provider, renumbering of the address
prefix (n) was built into IPv6 addressing.
• As we discussed before, each site is given a prefix by the service provider
to which it is connected. If the site changes the provider, the address
prefix needs to be changed.
• A router to which the site is connected to can advertise a new prefix and
let the site use the old prefix for a short time before disabling it. In other
words, during the transition period, a site has two prefixes.
30. IPv6 Provider-Based Addresses
The first IPv6 addresses will be allocated to a provider-
based plan
Type: Set to “010” for provider-based addresses
Registry: identifies the agency that registered the address
The following fields have a variable length (recommended lengths are in“()” )
Provider: Id of Internet access provider (16 bits)
Subscriber: Id of the organization at provider (24 bits)
Subnetwork: Id of subnet within organization (32 bits)
Interface: identifies an interface at a node (48 bits)
Registry
ID
Provider
ID
010
Subscriber
ID
Interface
ID
Subnetwork
ID
31. IPv6 Address Types
Unicast – identifies a single interface on a single
node. A unicast packet is delivered to the
identified single interface.
Multicast - identifies a set of interfaces that
belong to different nodes. A multicast packet is
delivered to all identified interfaces.
Anycast – a global unicast address such as DNS
that is assigned to a set of interfaces that belong
to different nodes. An anycast packet is
delivered to the closest interface.
For more information on Unicast, Multicast and Anycast, you may visit the
website:
http://www.omnisecu.com/tcpip/ipv6/unicast-multicast-anycast-types-of-
network-communication-in-ipv6.php
Broadcast – Not in IPv6!!!
32. IPv6 Unicast Addresses
64 bits for Global Routing and Subnet + 64 bits
for Interface ID
Prefix + Subnet ID + Interface ID = 128 bit IPv6
Address
Prefix is the Global Routing Prefix (48 bits)
Subnet ID is the subnet identifier within a site (16 bits)
Interface ID is the interface identifier for a particular host or
other device (64 bits)
From ONE: To ONE:
SOURCE -----------------------------Unicast Destination
33. IPv6 Multicast Addresses
1st 8 bits are all 1’s i.e., 1111 1111; Translate into Hex: FF
Indicator (8 bits) + Flags (4 bits) + Scope ID (4 bits) + Group ID
(112 bits) = IPv6 128 bit Multicast Address
Indicator – 1st eight bits set to 1’s signifying a multicast
packet.
Flags – 1st three are 0’s. The last is either a “0” for a
permanent/well known multicast address or a “1” for a
temporary multicast address.
Scopes – Globally across the Internet or Locally within the
organization
Group – Defines a particular group within a scope.
From ONE: To MANY:
SOURCE Multicast Destinations
Multicast Destinations
Multicast Destinations
34. Multicast Scopes
Node-Local
(within a
node)Scope (1)
Link-Local (within
a local network)
Scope (2)
Site-Local (within
a local site)
Scope (5)
Organization-
Local (within an
organization)
Scope (8)
Global (across
the Internet)
Scope (14)
Note: As the Scope ID Value Increases, the Scope
expands to cover larger areas.
35. Well Known Multicast
Addresses
FF01:0:0:0:0:0:1 used to multicast to all nodes for node-local.
(Notice: FF signifies multicast, scope id of 1 signifies node-local, and group
id of 1 signifies all nodes)
FF02:0:0:0:0:0:1 used to multicast to all nodes for link-local. (Notice:
FF signifies multicast, scope id of 2 signifies link-local, and group id of 1
signifies all nodes)
FF01:0:0:0:0:0:2 used to multicast to all routers for node-local.
(Notice: FF signifies multicast, scope id of 1 signifies node-local, and group
id of 2 signifies all routers)
FF02:0:0:0:0:0:2 used to multicast to all routers for link-local.
(Notice: FF signifies multicast, scope id of 2 signifies link-local, and group
id of 2 signifies all routers)
FF05:0:0:0:0:0:2 used to multicast to all routers for node-local.
(Notice: FF signifies multicast, scope id of 5 signifies site-local, and group
id of 2 signifies all routers)
Multicasting to “all nodes” replaces IPv4 Broadcasts.
36. IPv6 Anycast Addresses
Anycast Packets are new to IPv6
Automatically sends packet to the closest member within a group.
Provides flexibility when requesting a service provided by several
different routers.
Designed for devices within the same network.
Addresses assigned from Unicast Addressing space.
From ONE: To ONE of Many:
SOURCE ------------------------------- Multicast Destination
------------------------------- Multicast Destination
----------------------------- CLOSEST Multicast Destination
37. IPv6 Special Addresses
Reserved – reserved by IETF for special uses. First
eight bits are 00000000.
Private – private addresses are local to a particular site
or company network and are never routed outside that
network. First nine bits are: 111111101
Loopback – used for testing the “loop back” of the
device. 0:0:0:0:0:0:0:1/128 or ::1/128
Unspecified – used in certain cases such as default
routes but this address should not be assigned to any
host. All 128 bits are zeroes noted as 0:0:0:0:0:0:0:0,
or ::, or 0::0.
38. Who’s in charge?
IANA – Internet Assigned Numbers Authority is in
charge of all IP address assignment and internet
parameters. (owned and ran by ICANN)
ICANN – Internet Corporation for Assigned Names and
Numbers is a private, non-profit company responsible for
all registration tasks such as IP address assignment,
domain name assignment, and protocol parameters
management. (ICANN has allowed accredited registrars
to register names in many of the top-level domains)
Often referred to as: IANA/ICANN or ICANN/IANA
39. Migrating from IPv4 to IPv6
Methods that make the migration easier:
Dual-Stack – running both IPv4 and IPv6
simultaneously. Applications talk to both.
Tunneling – wrapping or packaging one type of
packet into another to be sent on dissimilar network
i.e., tunneling ipV6 packets on IPv4 network.
Translation – converting IPv4 to IPv6 and vice versa
which can be complex and result in problems.
Required for devices that only support one version.
(temporary solution until more devices make the
move to IPv6)
IPv6/IPv4 Address Embedding – embeds the
IPv4 addresses within the IPv6 address structure
40. Dual-Stack
Devices speak both IPv6
and IPv4.
Both IPv4 and IPv6 are
operational on all
components(hosts, servers,
routers, switches, and
firewalls) attached to the
network.
Dual Stack is the primary
approach for introducing
IPv6 into an IPv4 network
41. Tunneling
Enables interconnection of
IP networks.
IPv6 networks can be
connected through an IPv4
WAN link.
IPv6 packets are
encapsulated and de-
capsulated by border routers
for transmission over the
IPv4 WAN link.
Thus, IPv6 packets are
tunneled through the IPv4
network cloud.
42. Translation
Required when IPv6 host
needs to communicate with
IPv4 host.
Application Level Gateways
(ALGs) are required to
translate.
Can be implemented in
border routers and hosts.
Temporary Solution
Complexity and overhead
issues
43. IPv6/IPv4 Address Embedding
These are special addresses assigned
to IPv6-capable devices, such as so-
called “dual stack” devices that
speak both IPv4 and IPv6.
The first 80 bits are zeroes.
They have also all zeroes for the
middle 16 bits; thus, they start off
with a string of 96 zeroes, followed
by the IPv4 address
IPv4 addresses are put in special
format IPv6 address so they are
recognized as IPv4 addresses by
IPv6 devices.
44. 44
IPv4 Addressing Concepts and Their IPv6 Equivalents
IPv4 Address IPv6 Address
Address Length – 32 bits 128 bits
Address Representation - decimal hexadecimal
Internet address classes Not applicable in IPv6
Multicast addresses (224.0.0.0/4) IPv6 multicast addresses (FF00::/8)
Broadcast addresses Not applicable in IPv6
Unspecified address is 0.0.0.0 Unspecified address is ::
Loopback address is 127.0.0.1 Loopback address is ::1
Public IP addresses Global unicast addresses
Private IP addresses (10.0.0.0/8,
172.16.0.0/12, and 192.168.0.0/16)
Site-local addresses (FEC0::/10)
Autoconfigured addresses (169.254.0.0/16) Link-local addresses (FE80::/64)
Need private addressing and Network
Address Translation (NAT)
Does not need NAT
Network bits representation: Subnet
mask in dotted decimal notation or prefix
length.
Network bits representation: Prefix
length notation only.
45. IPv6 Post Check
Now, go back to your IPv6 Pre/Post
Concept Check paper with your Key Terms
Rate your understanding of the Key Terms
on the Right Side. Remember:
(+) = Expert
(√ ) = Heard of it
(-) = Have not heard of it
Reflection as a group.
46. Summary
IPv6 or Internet Protocol Version 6 is the successor to IPv4 or
Internet Protocol Version 4. It is needed to address the need
for additional address space with an ever growing Internet
population as well as new internet devices.
IPv6 addresses are written in Colon Hex notation.
IPv6 addresses are Unicast, Multicast, and Anycast.
Broadcast is not part of IPv6.
IPv6 has four special addresses: Reserved, Private,
Loopback, and Unspecified.
Two colons in an address represent successive leading zeroes.
Full IPv6 deployment will take years. IPv4 and IPv6 must
coexist in the meantime. Dual-Stack, Tunneling, Translation,
and IPv6/IPv4 Address Embedding all make the migration
easier.