IMPORTANT SAFEGUARDS FOR AUDIO PRODUCTSPLEASE READ CAREFULLY THE FOLLOWING IMPORTANT SAFEGUARDS THAT AREAPPLICABLE TO YOUR EQUIPMENT.1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.2. Retain Instructions - The safety and operating instructions should be retained for future reference.3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.4. Follow Instructions - All operating and use instructions should be followed.5. Water and Moisture - The appliance should not be used near water, for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool and the like.6. Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.7. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.8. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilationopenings, or placed in a built-in installation, such as a bookcase or cabinet that mayimpede the flow of air through the ventilation openings.9. Heat - The appliance should be situated away from heat sources such as radiators, heaters, ovens, cookers or other appliances (including amplifiers) that produce heat.10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.11. Grounding or Polarization - Precautions should be taken so that the grounding or polarization means of an appliance is not impeded.12. Power - Cord Protection – Power supply cords should be routed so that they are not likely to be walked on or squeezed by items placed upon or against them, paying particular attention to where the cord is connected to the power plug, and the point where they exit from the appliance.13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer.14. Antenna - This product is designed for use with the antenna attached and should not be connected to any other external antennas.15. Non-use Periods - The power cord of the appliance should be unplugged from the wall outlet when left unused for a long period of time.16. Object and Liquid Entry - Care should be taken so objects do not fall and liquids are not spilled into the enclosure through openings.17. Damage Requiring Service - The appliance should be serviced by qualified service
personnel only when: a) The power supply cord of the plug has been damaged. b) Objects have fallen, or liquid has been spilled into the appliance. c) The appliance has been exposed to rain. d) The appliance does not appear to operate normally or exhibits a marked change in performance. e) The appliance has been dropped, or the enclosure damaged.18. Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.POWER SOURCE1 Untie the wire on the AC Adaptor2 Plug the AC Adaptor into appropriate wall outlet.3 Plug the small end of the adaptor into the ACADAPTOR JACK on the back of the unit.UNPACKING THE TURNTABLE1. Remove packing materials from unit. Note: Save all packing materials.2. Remove plastic bag covering radio.3. Open lid and remove styrofoam shipping material from turntable.4. Remove black tie-wrap from under the tone arm.5. Remove white protective needle cover by gently pulling towards the front of the unit.6. Untie the FM antenna and allow it to hang down in a straight line for optimum FM reception. If you have trouble tuning in an FM station, move the external FM antenna for best reception. Do not connect FM antenna to outside antenna.TURNTABLE OPERATION1. Select the CD/PHONO/RADIO/TAPE SWITCH to PHONO mode.2. Set the SPEED CONTROL SWITCH to desire speed (33 1/3,45 or 78 rpm). Place the record on the turntable.3. Pull the TONE ARM slightly to the right side until hear the “click” sound to activate the turntable.4. Move the TONE ARM by hand out over the record and slowly lower it. Adjust the VOLUME DOWN/UP KNOB to the desire listening level.5. At the end of the record, the TONE ARM will stop automatically. You must return it to the TONE ARM REST by hand.Accessory: ADAPTER FOR 45 RPM1 Place the 45 RPM adaptor over the spindle.
2 Gently place your 45 RPM record onto the turntable.3 Follow the steps under turntable operation to play your record.ANTENNAAntenna: for FM reception, the unit is provided with a FM WIRE ANTENNA , move the wire until thereception is clear and with no interferences. For AM reception, the unit is provided with a directionalbuild-in ferrite antenna. Rotate the set to find the position in which the best reception is obtained.Do not connect the FM WIRE ANTENNA to any outside antenna.RADIO OPERATION1. Press the POWER BUTTON to power on.2. Select the CD/PHONO/RADIO/TAPE SWITCH to radio position.3. Set the AM/FM BAND SWITCH to the desired radio band (AM or FM)4. Tune in the desired station by rotating the TUNING KNOB as desired.5. Adjust the sound level by turning the VOLUME DOWN/UP KNOB.CASSETTE OPERATION1. Select the CD/PHONO/RADIO/TAPE SWITCH to tape position, then insert a prerecorded tape through the CASSETTE DOOR.2. Adjust the volume level by turning the VOLUME UP/DOWN KNOB.3. For fast forwarding, press the EJECT/F.F. BUTTON half way in. Pressing again, will stop the fast forwarding and return the cassette to the playing mode.4. To stop and eject the cassette, press the EJECT/F.F. BUTTON in completely.5. When one side of the tape finishes playing, the cassette will automatically stop. Note: Remove the tape from the unit when it is not in use or stopped.CD OPERATION1. Select the CD/PHONO/RADIO/TAPE SWITCH or press CD BUTTON to CD position of the CD LED INDICATOR will be on .2. Press OPEN/CLOSE BUTTON to open the door.3. Place a CD disc to the tray and then press OPEN/CLOSE BUTTON to close the door, the display will show "---" for a few second, then total number of the tracks will be show ondisplay.4. Press the PLAY/PAUSE BUTTON to start playback and the PLAY/PAUSE LED INDICATOR will be on.5. Adjust the sound level by turning the VOLUME DOWN/UP KNOB as desired.6. Stop playback temporarily, press the PLAY/PAUSE BUTTON the PLAY/PAUSE LED INDICATOR will flash, press the PLAY/PAUSE BUTTON again resume playback.7. To stop playback, press the STOP BUTTON and the PLAY/PAUSE LED INDICATOR will be off.
SD CARD OR USB OPERATION1. Select the CD/PHONO/RADIO/TAPE SWITCH to CD position of the LED INDICATOR will on and then press the FUNCTION BUTTON repeatedly to select SD or USB of the LED indicator will on. on remote ,press SD BUTTON or USB BUTTON to select SD or USB of the LED indicator will on.2. Load an SD card into the SD card slot or connect the USB memory device to the USB port.3. Then press the PLAY/PAUSE BUTTON to start playback SD card or USB memory device of the PLAY/PAUSE LED INDICATOR and MP3 LED INDICATOR indicator will be on.4. Press the BUTTON or BUTTON to select a desired track.5. Stop playback temporarily, press the PLAY/PAUSE BUTTON the PLAY/PAUSE LED INDICATOR will be flash, press again the PLAY/PAUSE BUTTON again resume playback.REMOVING THE SD CARD OR USB DEVICEPress the STOP BUTTON, then switch to other function mode before removing the device.Note: Do not disconnect the SD card or USB memory device during playback. If do, the data may be damaged.FOLDER/FILE SELECTIONIn the stop mode, press the FOLDER + BUTTON or FOLDER - BUTTON, the folder numberappears briefly to select the desired file.When desired file is selected in stop and then press the PLAY/PAUSE BUTTON to startplayback.SKIP OR SEARCH OF THE TRACKS1. Press the BUTTON or button to desired tracks.2. Press and hold BUTTON or BUTTON search within the current track, release the button to resume play.REPEAT OR RANDOM PLAYBACK1. To select the single track repeat function, choose the track that you want to repeat, then In stop or play mode, Press the MODE BUTTON once, to activate the single track repeat and the REPEAT LED INDICATOR will flash.2. To select the all tracks repeat function, in stop or play mode, Press the MODE BUTTONtwice, to active the all tracks repeat function and the REPEAT LED INDICATOR will remainon. Note: when you press the MODE BUTTON twice to repeat folder function and the FOLDER LED INDICATOR will be flash, if you again to press the MODE BUTTON the LED indicator will be off and continually to repeat all tracks for MP3 only.3. To select the random play function, Press MODE BUTTON twice again to start random play and the RANDOM LED INDICATOR will be on.4. To stop the function, press the MODE BUTTON third to resume normal play.
CD-MP3 SD OR USB PROGRAMMED PLAYBACK1. Press the PROGRAM BUTTON "P01" will show on the display and the PROGRAM LED INDICATOR will flash.2. Press the BUTTON ) or BUTTON to select desired tracks.3. Press the PROGRAM BUTTON again to in-store the selected track number.4. Repeatedly steps 2 and 3 above to program other tracks.5. Press the PLAY/PAUSE BUTTON to start programmed playback and the PROGRAM LED INDICATOR will be on.6. To erase the programmed sequence, press the STOP BUTTON twice or until the PROGRAM LED INDICATOR is off.Note: Maximum of CD 20 tracks can be programmed to play in any order. Maximum of CD MP3 99 tracks can be programmed to play in any order.REMOTE CONTROLPress the +10 TRACK BUTTON or -10 TRACK BUTTON to skip the track of 10 step andmaximum up to 999 tracksASSEMBLY OF THE HORN PROCEDURE1. Push the wire through the Horn holder. Picture (1).2. Rotate the Horn and the Horn Holder according to the picture direction.Picture (2).3. Plug-in the speaker wire together. Picture (3).4. Place the Horn Holder over the Horn Base. Picture (4).5. Rotate the Screw Bushing to tighten according to the picture direction.Picture (5).TROUBLE SHOOTING GUIDE
THERE IS NO POWER1. Make sure the Power source is connected.2. Make sure the unit power on .THERE IS NO SOUND1. Check the volume level by turning the volume knob.2. Make sure the unit under correct function mode.TURNTABLE WILL NOT WORK1. Make sure the unit is set to Phono mode.2. Check the cassette player to make sure a cassette is not playing.3. Make sure the protective needle cover is removed.CD DOES NOT PLAY1. Make sure CD is inserted correctly (label side facing up).2. Check that the surface of the CD is clean.3. Make sure the unit is under CD mode.4. Make sure the CD is not blank.LOCATION OF PARTS1 SPEAKERS2 SD CARD SLOT3 CD LED INDICATOR4 SD LED INDICATOR5 USB LED INDICATOR6 CD/PHONO/RADIO/TAPE SWITCH7 AM/FM BAND SWITCH8 CD DRAWER9 PLAY/PAUSE BUTTON10 REPEAT LED INDICATOR11 STOP BUTTON12 MP3 LED INDICATOR13 * BUTTON14 * BUTTON15 PROGRAM BUTTON16 FOLDER - BUTTON17 RANDOM LED INDICATOR18 FOLDER + BUTTON19 FOLDER LED INDICATOR20 MODE BUTTON21 FUNCTION BUTTON22 POWER BUTTON23 OPEN/CLOSE BUTTON24 USB PORT
25 TUNING KNOB26 PROGRAM LED INDICATOR27 LED DISPLAY28 DIAL SCALE29 SENSOR30 PLAY/PAUSE LED INDICATOR31 VOLUME DOWN/UP KNOB32 SCREW BUSHING33 AC ADAPTOR JACK34 HORN BASE35 EXTERNAL ANTENNA36 HORN37 HORN HOLDER38 TONE ARM39 CUE LEVER40 SPEED CONTROL SWITCH (331/3, 45, 78 RPM)41 SECURITY HOOK42 ARM REST43 EJECT/F.F. BUTTON44 CASSETTE DOOR45 ADAPTER FOR 45 RPM RECORD46 SPINDLE47 TURNTABLE48 PLAY/PAUSE BUTTON49 SD BUTTON50 CD BUTTON51 STOP BUTTON52 PROGRAM BUTTON53 +10 TRACK BUTTON54 * BUTTON55 * BUTTON56 -10 TRACK BUTTON57 USB BUTTON58 MODE BUTTON59 FOLDER + BUTTON60 FOLDER - BUTTONWARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT
REMOVE COVER. PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE PARTS INSIDE. REFERSERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to SHOCK DO NOT OPEN The exclamation point within an equilateral triangle is intended to alert user to the alert user to the presence of uninsulated presence of important operating and "dangerous voltage" within the products CAUTION: TO REDUCE THE RISK OF maintenance (servicing) instruction in the enclosure that may be of sufficient magnitude ELECTRIC SHOCK, DO NOT REMOVE literature accompanying the appliance. to constitute risk of electric shock to persons. COVER (OR BACK). NO USER – SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.SPECIFICATIONFREQUENCY RANGE : FM 88 - 108 MHz : AM 530 - 1600 KHzPOWER SOURCE : DC 12V DC 1.2A *ANTENNAS : External antenna for FM : Built-in ferrite bar for AMTURNTABLE SPEED : 33 1/3 /45 /78 RPMUSB 2.0 PORT : Up to 8G byte MAXSPEAKER : 3” x 4” 8ohm Dynamic type x 2*DESIGN AND SPECIFICATION SUBJECT TO CHANGE WITHOUT NOTICE. 910-121121-0010-100