Your SlideShare is downloading. ×
Manual de Recarga Lexmark T430
Upcoming SlideShare
Loading in...5
×

Thanks for flagging this SlideShare!

Oops! An error has occurred.

×
Saving this for later? Get the SlideShare app to save on your phone or tablet. Read anywhere, anytime – even offline.
Text the download link to your phone
Standard text messaging rates apply

Manual de Recarga Lexmark T430

1,212
views

Published on

Manual utilizado nos modelos Lexmark T430.

Manual utilizado nos modelos Lexmark T430.

Published in: Technology

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
1,212
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
30
Comments
0
Likes
0
Embeds 0
No embeds

Report content
Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
No notes for slide

Transcript

  • 1. T420/430TECH Technical Instructions Printers/Supplies Tools 1 Printers: Needlenose Pliers CORPORATE Lexmark T420dn Phillips Screwdriver LOS ANGELES, USA Lexmark T430/430d/430dn Small Flat Blade Screwdriver US 1 800 394.9900 Spring Hook Int’l +1 818 837.8100 FAX 1 800 394.9910 Supplies: X-Acto Knife Int’l +1 818 838.7047 T420 High Yield Return Program Print Cartridge 12A7415 T420 Return Program Print Cartridge 12A7410 Supplies Required: ATLANTA, USA T420 High Yield Print Cartridge 12A7315 Toner US 1 877 676.4223 T420 Print Cartridge 12A7310 Wiper Blade Int’l +1 770 516.9488 Drum FAX 1 877 337.7976 Int’l +1 770 516.7794 T430 High Yield Return Program Print Cartridge 12A8425 Lint free cloth T430 Return Program Print Cartridge 12A8420 99% isopropyl alcohol DALLAS, USA T430 High Yield Print Cartridge 12A8325 Cotton Swabs US 1 877 499.4989 T430 Print Cartridge 12A8320 Int’l +1 972 840.4989 FAX 1 877 774.1750 Int’l +1 972 840.1750 Photo 1 Step 1 MIAMI, USA US 1 800 595.429 Place the cartridge top down on the table with Int’l +1 305 594.3396 the drum facing up and the gear end of the FAX 1 800 522.8640 toner hopper is facing towards you. Using a Int’l +1 305 594.3309 small flat blade screwdriver, pry off the devel- NEW YORK, USA oper roller drive gear and set it aside. US 1 800 431.7884 (See Photo 1) Int’l +1 631 345.0121 FAX 1 800 431.8812 Int’l +1 631345.0690 SANFORD,USA US 1 800 786.9049 Int’l +1 919 775.4584 FAX 1 800 786.9049 Int’l +1 919 775.4584 Photo 2 Step 2 TORONTO, CAN Rotate the cartridge to the right so the toner CAN 1 877 848.0818 hopper is facing you. Using a spring hook or Int’l +1 905 712.9501 needle nose pliers, gently remove the toner FAX 1 877 772.6773 hopper tension springs from the posts at each Int’l +1 905 712.9502 side. (See Photo 2 and 3) BUENOS AIRES, ARG ARG 0810 444.2656 Int’l +011 4583.5900 FAX +011 4584.3100 MELBOURNE, AUS AUS 1 800 003. 100 Int’l +62 03 9561.8102 FAX 1 800 004.302 Int’l +62 03 9561-7751 SYDNEY, AUS Photo 3 AUS 1 800 003.100 Int’l +62 02 9648.2630 FAX 1800 004.302 Int’l +62 02 9548.2635 MONTEVIDEO,URY URY 02 902.7206 Int’l +5982 900.8358 FAX +5982 908.3816 JOHANNESBURG, S.A. S.A. +27 11 974.6155 FAX +27 11 974.3593 E-mail: info@futuregraphicsllc.com Website: www.futuregraphicsllc.com
  • 2. 2 Lexmark T420/430 Technical Instructions Photo 6 Step 5 While holding the drive gear of the drum, pull the drum axle out. (See Photo 6) Step 3 While holding onto the toner hopper with your left hand, carefully bend the waste hopper away from the gear side of the toner hopper using your right hand. Lift the right side of the toner hopper up away from the waste hopper. (See Photo 4) Photo 7 Remove the drum and set it aside, being sure not to lose the spring attached to the small Separate the toner hopper and gear side. (See Photo 7) waste hopper. Set the toner hopper aside. If you plan on reusing the drum, place the drum NOTE: Do not lose toner hopper in a protected area and out of the light. tension springs. Photo 4 Photo 8 Step 6 Fold together two plates of PCR access shutter. Using your right hand, bend the shutter in the middle and, carefully bending the waste hopper away with your left hand, remove the shutter pin from the hopper. Remove the other pin and slid- ing guide of the shutter from the waste hopper. Be careful not to damage the waste hopper recovery blade.(See Photo 8) Photo 9 Step 7 Step 4 Place the waste hopper flat on the work bench. Place the waste hopper with the Using a Philips screwdriver remove the two drum facing up. Using a small flat screws that hold the wiper blade to the waste blade screwdriver remove the “C” hopper.(See Photo 9) clip from the drum axle on the drive (large) gear end of the drum. (See Photo 5) Step 8 Using a small flat blade screwdriver pry the Photo 5 wiper blade away from the waste hopper. (See Photo 10) Photo 10 Remove the wiper blade. (See Photo 11) Photo 11 Need trust-worthy, detailed Technical Instructions for another engine? Visit: www.futuregraphicsllc.com
  • 3. Lexmark T420/430 Technical Instructions 3 Photo 12 Step 9 Dump the waste toner from the hopper. Using dry compressed air or a vacuum, clean the waste hopper. Visually inspect the waste hop- per recovery blade. If the blade is wavy, Step 14 nicked, or torn, the blade will have to be replaced. (See Photo 12) Place the toner hopper on the table (label up) with the developer roller facing you. Carefully remove the doctor blade tension spring from the hopper. (See Photo 17) NOTE: Do not let the tension spring Photo 13 Step 10 slip and hit the developer roller. This Apply a small amount of padding powder to the will scratch the roller and could new wiper blade. Place the new blade onto the cause print defects. waste hopper and install the two screws that hold the blade in place. (See Photo 13) Photo 17 Photo 14 Step 11 Holding PCR access shutter with your left hand, install the shutter pin and sliding guide into the waste hopper. Fold together two plates of PCR access shutter, bend the shutter with your right hand and install the other pin into the hopper. Be careful not to damage the waste hopper recovery blade. (See Photo 14) Step 15 Using a small flat blade screwdriver pry the developer roller contact off the brass contact bearing and slide the bearing from the end of the Photo 15 hopper and off the developer roller. Step 12 (See Photo 18) Apply a small amount of padding powder to the drum. Install the spring on the small gear side. This spring is to prevent the drum from turning backwards. Place the drum into the waste hopper. Slide the drum axle through the Photo 18 drum starting from the large (contact) gear side of the waste hopper. (See Photo 15) Install the “C”clip onto the drum axle. Photo 16 Step 13 Using a Philips screwdriver remove the screw that holds a chip to the waste hopper. (See Photo 16) Install a new chip. Set the waste hopper aside in a protected area out of the light.
  • 4. 4 Lexmark T420/430 Technical Instructions Photo 19 Step 16 While holding the shaft of the developer roller, lift the roller out from the hopper and slide the Notes developer roller axle out from the toner hopper gear end plate. (See Photo 19) Step 17 Remove the Teflon shims from the developer roller and inspect them for damage and wear. Replace the Teflon shims as a set if necessary. Photo 20 Step 18 Turn the toner hopper to the right so the fill plug is facing you. Using a small flat blade screw- driver, pry out the toner fill plug carefully and try not to damage it. Clean the filter inside the fill plug with either vacuum or compressed air. (See Photo 20) Photo 21 Step 19 Dump out the toner from the toner hopper. Using dry compressed air or a vacuum clean the toner hopper. Be very careful not to damage the toner hopper sealing blade. (See Photo 21) Photo 22 Step 20 Using a cotton swab and Isopropyl alcohol, clean the developer roller end seals. (See Photo 22) Photo 23 Step 21 Clean the contacts of the toner hopper using a cotton swab and Isopropyl alcohol. (See Photo 23) E-mail: info@futuregraphicsllc.com Website: www.futuregraphicsllc.com
  • 5. Lexmark T420/430 Technical Instructions 5 Photo 24 Step 22 Clean the underside of the doctor bar with a cotton swab and isopropyl alcohol. (See Photo 24) Notes Step 23 Visually inspect the inner sealing blade. If the blade is damaged it will cause leaking and must be replaced. Photo 25 Step 24 Clean the developer roller with a compressed air. Place the axle of the developer roller into a drill. Take a lint free cloth, add a small amount of alcohol, then soak the cloth with water. Clean the roller using the lint free cloth while the roller is rotating in the drill. (See Photo 25) Photo 26 Step 25 Clean the developer roller shaft with a cotton swab and alcohol. (See Photo 26) Photo 27 Step 26 Install the Teflon shims on each end of the developer roller and slide the keyed end of the developer roller axle into the gear assembly end plate. Lower the other end into position being careful not to damage the Teflon shim on that side. (See Photo 27) Photo 28 Step 27 Using a small flat blade screwdriver or needle nose pliers pry the developer roller contact off the developer roller shaft and install the brass contact bearing onto the end of the developer roller shaft. Slide it into place on the end of the toner hopper. (See Photo 28)
  • 6. 6 Lexmark T420/430 Technical Instructions Photo 31 Step 30 Place the waste hopper top down on the work bench with the waste hopper away from you. Step 28 Turn the toner hopper upside down, install the left side of the toner hopper first. Reinstall the doctor bar tension spring so the“V” stamp on the While holding onto the toner hopper with your spring points away from the toner left hand, carefully bend the waste hopper hopper. (See Photo 29) away from the gear side of the toner hopper using your right hand. Push the right side of the toner hopper toward the waste hopper. (See Photo 31) Photo 29 Photo 32 Step 31 Using a spring hook reattach the tension springs to each end of the toner hopper. (See Photo 32) Photo 33 Step 32 Step 29 Install the developer roller drive gear onto the developer roller axle. (See Photo 33) Fill the toner hopper with the The cartridge is now ready to test. correct amount of toner and reinstall the toner hopper fill plug. (See Photo 30) NOTE: The difference between T-420 and T-430 cartridges is a notch in the center of the front side of the T-430 cartridge waste section. (See Photos 34 and 35) Photo 34 T-420 CARTRIDGE Photo 30 Photo 35 T-430 CARTRIDGE Future Graphics (FG) is a distributor of compatible replacement parts and products for imagining equipment. None of FG's products are genuine OEM replacement parts and no affiliation or spon- sorship is to be implied between FG and any OEM. E-mail: info@futuregraphicsllc.com Website: www.futuregraphicsllc.com