Fiber Optic Termination

  • 452 views
Uploaded on

My presentation during Fiber Optic class for CFOT certificate

My presentation during Fiber Optic class for CFOT certificate

  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Be the first to comment
No Downloads

Views

Total Views
452
On Slideshare
0
From Embeds
0
Number of Embeds
0

Actions

Shares
Downloads
21
Comments
0
Likes
1

Embeds 0

No embeds

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
    No notes for slide

Transcript

  • 1. ENGINEEER TEAM SULAIM BIN AB QAIS (ENGINEER) WAN MOHD AKIF BIN WAN ABDUL RANI (A.ENGINEER)MOHD DAIM BIN HAMDAN (A.ENGINEER) MOHD FAIZ BIN KAMARUL ZAMAN (A.ENGINEER)
  • 2. PREPARECONNECTO LOAD INSERT CRIMPR FERRULE FIBER INTO CONNECTO WITH CONNECTO RPREPARE R EPOXYFIBER ANDCLEAN CURE EPOXY CLEAN AND CLEAVEINSPECT FINAL EXCESS POLISHFERRULE CONNECTO FIBRE FROM FERRULEAND FIBRE R ASSEMBLY FERRULE END-FACEEND-FACE
  • 3. ARAMICYARN GLASS FIBERJACKE BUFFE RT ¾ inch ¾ inch
  • 4. REMOVE THE OUTER COATING OF THEFIBER CABLEREMOVE ALL THE STRENGHT MEMBERAND THE SUPPORTING MATERIALREMOVE INDEX GEL OR KEVLARSTRIP THE COLOUR-CODED COATING (typ250u)CLEAN THE FIBER USING ALCOHOL
  • 5.  Load the mixed epoxy into a syringe (unless its pre-loaded of course). Inject the epoxy into the back end of the connector ferrule. Insert the prepared cable into the connector such that the bared fiber is inserted into the ferrule hole. Insert until the cable seats inside the connector. The fiber will be protruding out the front of the ferrule by typically ½ inch. Crimp: If the connector is being installed onto jacketed fiber, a crimping operation is required to retain the connector onto the cable strength members and jacket. This is usually accomplished via use of a crimp sleeve and, in order to retain the connector onto the cables strength members as well as the jacket, two crimps are typically required.
  • 6.  Insertthe bare fiber into the connector Perform crimping Cleaving (manual or auto)
  • 7. PATCHCORD
  • 8. A patch cable or patch cord is an electrical or optical cable used to connect ("patch-in") one electronic or optical device to another for signal routing. Firstly, Crimping kevlar sleeve onto the connector Slide the strain relief boot up to the connector
  • 9.  A fibre is a single short, usually unbuffered, optical fibre that has an optical connector on one end and a length of exposed fibre athe other end. The end of the pigtail is stripped and fusion spliced to a single fibre of a multi-fibre trunk to break out the multi- fibre cable into its component fibres for connection to the end equipment. Pigtails can have female connectors and be mounted in a patch panel A plastic boot is normally used for strain relief and protection from moisture.
  • 10. End-surface treatment for proper light propagation
  • 11. Polish film made Diamond, silicon carbide, andaluminum oxide
  • 12. POLISHING TYPE FOR CONNECTOR
  • 13. most popular type . . . UPC (Ultra-Physical Contact), and themore recent APC (Angle Polished Connector). UPC (coded blue/black) APC (Green)
  • 14. 1. Air polish
  • 15. 2. Surface polish
  • 16. 3. Fiber optic micro polisher
  • 17. •Toinspect the quality of the fiber surface. •Using a microscope100x,200x(Multimode Inspection) 400x(Singlemode Inspection)
  • 18.  Insertion Loss & Return Loss Return Loss are two importance data to evaluate the quality of many passive fiber optic components,such as fiber optic path cord and fiber connectors, etc.
  • 19.  Insertion Loss refers to the fiber optic light loss coused when a fiber optic component insert into another one to from the fiber optic link. Insertion loss can result from absorption, misalignment or air gap between the fiber optic components. Return Loss is the fiber optic light gets reflected back at the connection point. The higher return loss means the lower reflection and better the connection. According to industry standard, Ultra PC polished fiber optic connectors return loss should be more than 50dB, Angled polished generally return loss is more than 60dB. PC type should be more than 40dB.