• Share
  • Email
  • Embed
  • Like
  • Save
  • Private Content

Loading…

Flash Player 9 (or above) is needed to view presentations.
We have detected that you do not have it on your computer. To install it, go here.

Like this presentation? Why not share!

Using OmniPeek to capture 802.11 traffic from a Cisco access point

on

  • 6,405 views

Turn a Cisco access point into a sniffer and capture its traffic remotely with WildPackets OmniPeek.

Turn a Cisco access point into a sniffer and capture its traffic remotely with WildPackets OmniPeek.

Statistics

Views

Total Views
6,405
Views on SlideShare
3,762
Embed Views
2,643

Actions

Likes
2
Downloads
0
Comments
2

12 Embeds 2,643

http://blog.sudonetworks.com 2174
http://www.cisco-club.com.cn 311
http://www.swilliamsgroup.com 102
http://wwwin-blogs.cisco.com 21
http://translate.googleusercontent.com 16
http://www.linkedin.com 6
http://webcache.googleusercontent.com 5
http://cache.baidu.com 2
http://www.google.com.pk 2
http://static.slidesharecdn.com 2
http://www.youtube.com 1
http://web.archive.org 1
More...

Accessibility

Categories

Upload Details

Uploaded via as Microsoft PowerPoint

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel

12 of 2 previous next

  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment
  • On choisit le plugin Cisco Remote Adapter
  • On assigne un nom à notre plugin. Laissez l’IP en blanc.
  • L’IP source des paquets correspond à l’adresse du contrôleur WLC et non pas de l’AP

Using OmniPeek to capture 802.11 traffic from a Cisco access point Using OmniPeek to capture 802.11 traffic from a Cisco access point Presentation Transcript

  • OmniPeek and Cisco AP Sniffer Combo
    Steve Williams – Sudo Networks
    GCIH, CISSP
    Blog:blog.sudonetworks.com/wifi-edge
    LinkedIn: linkedin.com/in/sudosteve
    Twitter: twitter.com/stevewilliams_
    Sudo Networks Inc.
    1
  • OmnipeekConfiguring a Cisco AP to capture 802.11 traffic
    Steps
    Select a Cisco AP to capture traffic from
    Configure it for sniffing, select desired channel and OmniPeek workstation IP address
    Configure OmniPeek with Cisco Remote Adapter
    Start sniffing with OmniPeek
    Sudo Networks Inc.
    2
  • OmnipeekWLC: Select an AP for Sniffing
    Sudo Networks Inc.
    3
  • OmnipeekWLC: change AP Mode to Sniffer
    Sudo Networks Inc.
    4
  • OmnipeekWLC: AP will reboot
    Sudo Networks Inc.
    5
  • OmnipeekWLC: Select the band
    Sudo Networks Inc.
    6
  • OmnipeekWLC: Check the ‘Sniff’checkbox
    Sudo Networks Inc.
    7
  • OmnipeekWLC: select a channel to sniff and Omnipeek workstation IP address
    Sudo Networks Inc.
    8
  • OmnipeekConfiguring OmniPeek for sniffing Cisco AP
    Sudo Networks Inc.
    9
  • OmnipeekAdd <Cisco Remote Adapter> module to Omnipeek
    Sudo Networks Inc.
    10
  • OmnipeekStart Capture
    Sudo Networks Inc.
    11
  • OmnipeekSelect Omnipeek Adapter
    Sudo Networks Inc.
    12
  • OmnipeekDouble click Cisco Remote Adapter Module
    Sudo Networks Inc.
    13
  • OmnipeekSelect New Adapter and provide a name, leave IP address blank
    Sudo Networks Inc.
    14
  • OmnipeekSave changes
    Sudo Networks Inc.
    15
  • OmnipeekOmniPeek capture button changed to: Start Cisco Capture
    Sudo Networks Inc.
    16
  • OmnipeekOmniPeek now capturing from Cisco AP on channel 11
    Sudo Networks Inc.
    17
  • OmnipeekWindump shows UDP packets from WLC at 10.199.200.80
    Sudo Networks Inc.
    18