How to Fix a Motorola Atrix 2 MB865
visit www.StriveMobile.com to purchase your DIY kit
Release the following popconnectors by prying thecables up with a pry tool:   Speaker / Camera Flex Cable   Touch Screen...
With all the flex cablesreleased, you can now pry upthe motherboard and removeit fully from the Atrix 2
   Be sure to put the    speaker/camera flex    cable to the side. This    should lift out easily with    a pry tool.   ...
In order to remove theLCD screen from thefront housing you willneed to flex the upperor lower assembly togive yourself eno...
If you are only replacing the LCD screen, click here.    Using a heat gun or hair    dryer, warm the outside    edges of t...
With the adhesive warmed you can use apry tool to separate the glass touchscreen from the front housing. Wesuggest startin...
Apply fresh adhesiveto the front housing.We do not suggestputting adhesive onthe touch screen itselffor the Atrix 2.*Be su...
Begin feeding thedigitizer flex through theslot in the housing. Youcan then press the glassfirmly onto the frame,insuring ...
Press the LCD screen firmlyinto the front housing.If you have replaced the LCDscreen, be sure to removethe screen protecto...
Replace the eight (8) Torx T5screws back into the metal frame.Be sure to insert the speakerassembly prior to placing in th...
Place the motherboard overthe metal plate.Insert each pop connector:   Speaker Assembly Flex    Cable   Touch Screen Dig...
Place the back housing overthe motherboard and press itfirmly in place until all clips aresecure.Replace the following:  ...
And there you have it!Your Atrix 2 MB865 is nowlooking and working likenew again!Don’t forget to visit us atwww.StriveMobi...
Motorola Atrix 2 Screen Repair Guide - How to Replace a Broken Screen
Motorola Atrix 2 Screen Repair Guide - How to Replace a Broken Screen
Upcoming SlideShare
Loading in...5
×

Motorola Atrix 2 Screen Repair Guide - How to Replace a Broken Screen

4,682

Published on

This repair guide will walk you through the steps required to replace a screen on your Motorola Atrix 2. No matter if you have a cracked glass touch screen or a damaged LCD screen, this guide will get your Atrix 2 MB865 looking like new! Be sure to check out our full DIY screen repair kits for your Atrix 2 at http://www.strivemobile.com/motorola-atrix-2-screen-replacement-repair-parts

0 Comments
1 Like
Statistics
Notes
  • Be the first to comment

No Downloads
Views
Total Views
4,682
On Slideshare
0
From Embeds
0
Number of Embeds
6
Actions
Shares
0
Downloads
12
Comments
0
Likes
1
Embeds 0
No embeds

No notes for slide

Motorola Atrix 2 Screen Repair Guide - How to Replace a Broken Screen

  1. 1. How to Fix a Motorola Atrix 2 MB865
  2. 2. visit www.StriveMobile.com to purchase your DIY kit
  3. 3. Release the following popconnectors by prying thecables up with a pry tool: Speaker / Camera Flex Cable Touch Screen Digitizer Flex LCD Screen Flex
  4. 4. With all the flex cablesreleased, you can now pry upthe motherboard and removeit fully from the Atrix 2
  5. 5.  Be sure to put the speaker/camera flex cable to the side. This should lift out easily with a pry tool. Remove the eight (8) Torx T5 screws You can then remove the metal plate by using a pry tool to lift it from the bottom
  6. 6. In order to remove theLCD screen from thefront housing you willneed to flex the upperor lower assembly togive yourself enoughroom to fit a pry tooland pop the LCD fromits housing.
  7. 7. If you are only replacing the LCD screen, click here. Using a heat gun or hair dryer, warm the outside edges of the touch screen assembly. This will soften the adhesive holding the screens in place. Move quickly around the edges on medium heat for about 30 seconds.
  8. 8. With the adhesive warmed you can use apry tool to separate the glass touchscreen from the front housing. Wesuggest starting in this camera slot topush the touch screen away from theframe.
  9. 9. Apply fresh adhesiveto the front housing.We do not suggestputting adhesive onthe touch screen itselffor the Atrix 2.*Be sure you do not coverany camera or sensorholes with adhesive
  10. 10. Begin feeding thedigitizer flex through theslot in the housing. Youcan then press the glassfirmly onto the frame,insuring you haveremoved the screenprotector and wipedaway any debris fromthe screen.
  11. 11. Press the LCD screen firmlyinto the front housing.If you have replaced the LCDscreen, be sure to removethe screen protector andcleared the screen fromdust/finger prints, etc.
  12. 12. Replace the eight (8) Torx T5screws back into the metal frame.Be sure to insert the speakerassembly prior to placing in themotherboard.
  13. 13. Place the motherboard overthe metal plate.Insert each pop connector: Speaker Assembly Flex Cable Touch Screen Digitizer Flex LCD Screen Flex
  14. 14. Place the back housing overthe motherboard and press itfirmly in place until all clips aresecure.Replace the following: Nine (9) Torx T5 screws Sim Card Micro SD Card Battery Back Battery Cover
  15. 15. And there you have it!Your Atrix 2 MB865 is nowlooking and working likenew again!Don’t forget to visit us atwww.StriveMobile.com toorder your DIY MotorolaAtrix 2 Touch ScreenDigitizer Repair Kit!
  1. A particular slide catching your eye?

    Clipping is a handy way to collect important slides you want to go back to later.

×