Keep it watertight with



                                  Patent Pending


 Sealable scaffold attachment system for ext...
Patent Pending


                      THE PROBLEM
Water intrusion at conventional push pull wire ties.




              ...
Patent Pending




                                                                                         •       SAFETY...
Patent Pending



                             Welded Steel Anchor
                         INSTALLATION PROCEDURE
•      ...
Bumperite Attachment To Steel Bent Plate




Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting...
Patent Pending




                WOOD INSTALLATION PROCEDURE

 •       Determine spacing
         requirement to insure ...
Bumperite Attachment to Wood Framing




                        Allowable Nail Withdraw Value (P):

      Fastener Type  ...
Patent Pending




           STEEL FRAMED INSTALLATION PROCEDURE

 •       Determine spacing
         requirement to insu...
Bumperite Attachment to Light Gauge Framing




                       ALLOWABLE FORCE (P) = 1,000 LBS.
Minimum Design Req...
Bumperite Attachment to Light Gauge Framing

                                                                           AL...
Patent Pending




         CONCRETE INSTALLATION PROCEDURE

     •       Determine Bumperite
             spacing require...
Bumperite Attachment to Concrete Deck




Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting St...
Patent Pending




        BUMPERITE QUICK-TAB
                                             Optional feature

 •        Th...
Bumperite Quick-Tab Attachment




Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structura...
Patent Pending


       RECOMMENDED METHOD OF SEAL AT CONNECTION




  Manufacturer recommends the use of Densglass Gold e...
Step by Step   Patent Pending
Patent Pending



    RECOMMENDED METHOD OF SEAL AT WOOD / STEEL FRAMED
    ANCHOR PLATE TO EXTERIOR WATER MANAGEMENT SYST...
Step by Step at wood / steel framed plates   Patent Pending
Patent Pending


            BUMPERITE - VS - WIRE TIES
                          OSHA 1926.451(c)(1) states,
          Ca...
Upcoming SlideShare
Loading in …5
×

Bumperite Catalogue 2 Pdf

555 views
493 views

Published on

Published in: Business, Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
555
On SlideShare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
18
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Bumperite Catalogue 2 Pdf

  1. 1. Keep it watertight with Patent Pending Sealable scaffold attachment system for exterior plaster Enhance Safety and Eliminate Water Intrusion at Scaffold Ties Welded steel anchor Concrete anchor Wood/Steel anchor Toll Free (877) 490-8884
  2. 2. Patent Pending THE PROBLEM Water intrusion at conventional push pull wire ties. THE SOLUTION Sealable scaffold attachments. Bumperite Waterguards enhance Safety and eliminate Liability due to leaks caused by conventional scaffold wire ties assemblies.
  3. 3. Patent Pending • SAFETY OSHA compliant Engineered and tested structural attachment for scaffolding (4500) lbs. Report # L-06-3265 Ideal for tarped or enclosed scaffolds in high wind conditions. • REDUCED LABOR COST Eliminate costly end laps and their cuts to building papers verses conventional scaffold wire ties. Removable bumper allows easy access to difficult work areas.* Promotes the continuous installation of building materials. • RELIABILITY Water tested to ASTM E331-00 at Smith-Emery laboratories, Inc. Los Angeles, CA. Report # L-06-3059 *See installation instructions. WARRANTY: Bumperite Waterguards, LLC. liability expressed or implied is limited to the selling price of any defected goods. User shall determine the suitability of this product for the intended use by doing field test before using, and assumes all risk and liabilities in connection and seals therewith.
  4. 4. Patent Pending Welded Steel Anchor INSTALLATION PROCEDURE • Determine spacing requirement to insure safe scaffold erection.* • Measure distance between slab edge bent plate and outer face of stud framing. 1/8” • Cut the anchor strut to length as to flush out with face of stud framing. • Align the anchor strut with the bent plate and stud framing (true, square, and plumb) per detail. • Weld anchor strut to building bent plate per welding detail shown. • The use of a certified welder and E7018 rod or equal is recommended. *Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation. The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety. To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment.
  5. 5. Bumperite Attachment To Steel Bent Plate Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc
  6. 6. Patent Pending WOOD INSTALLATION PROCEDURE • Determine spacing requirement to insure safe scaffold erection.* • Review screw matrix provided to determine screw size and quantity required for safe installation. • Install Bumperite anchor plate where suitable framing and or backing occurs to ensure sufficient strength required to carry intended scaffold load. • Apply compatible sealant between Bumperite anchor plate & building papers to ensure seal at screws. • Ensure complete screw embedment at pre-drilled holes in anchor plate. See engineered detail. *Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation. The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety. To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment.
  7. 7. Bumperite Attachment to Wood Framing Allowable Nail Withdraw Value (P): Fastener Type w/ 2 Fasteners w/ 4 Fasteners w/ 6 Fasteners w/ 8 Fasteners 16d Nail 40 lbs. 80 lbs. 120 lbs. 160 lbs. 10d Nail 36 lbs. 72 lbs. 108 lbs. 144 lbs. Allowable Screw withdraw Value (P): Fastener Type (Screw Size x Length) w/ 2 Fasteners w/ 4 Fasteners w/ 6 Fasteners w/ 8 Fasteners #12 x 2" Screw 410 lbs. 820 lbs. 1080 lbs. 1232 lbs. #12 x 11⁄2" Screw 308 lbs. 616 lbs. 924 lbs. 1232 lbs. #10 x 2" Screw 360 lbs. 720 lbs. 1080 lbs. 1232 lbs. #10 x 11⁄2" Screw 270 lbs. 540 lbs. 810 lbs. 810 lbs. Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc
  8. 8. Patent Pending STEEL FRAMED INSTALLATION PROCEDURE • Determine spacing requirement to insure safe scaffold erection.* • Review backing plate requirements. • Install Bumperite anchor plate over 12 gage backing plate per diagram to ensure sufficient strength required to carry intended scaffold load. • Apply compatible sealant between Bumperite anchor plate & building papers to ensure seal at screws. • Ensure complete screw embedment at pre-drilled holes in anchor plate. See engineered detail. *Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation. The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety. To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment.
  9. 9. Bumperite Attachment to Light Gauge Framing ALLOWABLE FORCE (P) = 1,000 LBS. Minimum Design Requirements : : • For scaffold application this product complies w/ OSHA requirements • 12 ga. Deck Edge Clip • 18 ga. Wall Studs • 8”x12 ga.x11/2” Fl. Track • Track Blocking must be located within 6” of the Deck Edge Clip Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc
  10. 10. Bumperite Attachment to Light Gauge Framing ALT. #1 6” x 16GA x 1-1/2” FLANGE TRACK W / CUPPED FLANGES @ ENDS EXTEND WEB TAB ATTACHMENT TO (E) STUD AS SHOWN (4) # 8 S.M.S. EA. END ALLOWABLE FORCE (P) = 500 LBS. Minimum Design Requirements : : • For scaffold application this product complies w/ OSHA requirements • 12 ga. Deck Edge Clip • 18 ga. Wall Studs • 6”x16 ga.x1-1/2” Fl. Track • Track Blocking must be located within 6” of the Deck Edge Clip Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc
  11. 11. Patent Pending CONCRETE INSTALLATION PROCEDURE • Determine Bumperite spacing requirement and concrete psi values suitable for safe scaffold erection.* • Install Bumperite anchor plate at concrete slab edge with a minimum of two concrete anchors bolts, see engineered detail. • Install concrete anchors per manufactures installation guidelines. • Ensure complete anchor bolt embedment for maximum strength. See engineered detail. *Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation. The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety. To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment.
  12. 12. Bumperite Attachment to Concrete Deck Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc
  13. 13. Patent Pending BUMPERITE QUICK-TAB Optional feature • The specially designed Quick-tab is a scaffold erectors dream. • Fast and easy installation with no hassle. • A temporary attachment to building slab edge during scaffold erection prior to exterior wall framing and final welded attachment of Bumperite Waterguard. • Available upon request. • See engineered detail • WARNING: The Quick- tab attachment is not to be used at tarped or enclosed scaffolds. *Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation. The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety. To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment.
  14. 14. Bumperite Quick-Tab Attachment Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc
  15. 15. Patent Pending RECOMMENDED METHOD OF SEAL AT CONNECTION Manufacturer recommends the use of Densglass Gold exterior sheathing, butyl sealant, Tyvek Straight Flash, minimum UU-B-790a grade D, building paper, and three coat cement plaster per testing report L-06-3059 from Smith-Emery Laboratories, Inc. using test method ASTM E331-00 WARRANTY: Bumperite Waterguards, LLC. liability expressed or implied is limited to the selling price of any defected goods. User shall determine the suitability of this product for the intended use by doing field test before using, and assumes all risk and liabilities in connection therewith.
  16. 16. Step by Step Patent Pending
  17. 17. Patent Pending RECOMMENDED METHOD OF SEAL AT WOOD / STEEL FRAMED ANCHOR PLATE TO EXTERIOR WATER MANAGEMENT SYSTEM Water tested to ASTM E 1105-00 & ASTM E 331-00 by Architectural Testing, Inc. Report No: 90353.01-701-43 WARRANTY: Bumperite Waterguards, LLC. liability expressed or implied is limited to the selling price of any defected goods. User shall determine the suitability of this product for the intended use by doing field test before using, and assumes all risk and liabilities in connection therewith.
  18. 18. Step by Step at wood / steel framed plates Patent Pending
  19. 19. Patent Pending BUMPERITE - VS - WIRE TIES OSHA 1926.451(c)(1) states, Capacity- - Scaffolds and scaffold components must support at least 4 times the maximum intended load. Sealable & strength Difficult to seal & weaker Testing at Smith-Emery Laboratories suggest that the Bumperite Waterguard peak tension load is MANY TIMES STRONGER than conventional double strand #12 black annealed wire tie assemblies. See Our Web Site At Bumperite.com For More Information Please Contact Us At INFO@BUMPERITE.COM Toll free (877) 490-8884 Bumperite Waterguards, LLC.

×