Home | Account | Contact ALLDATA | Log Out | Help PAUL REDEHOFT
Select Vehicle | New TSBs | Technician's Reference Compone...
REMOVAL
1. REMOVE HOOD HINT: At the time of installation, please refer to the
following item. Adjust the hood.
2. REMOVE W...
3. REMOVE RH AND LH COWL TOP VENTILATOR LOUVERS
4. REMOVE NO. 2 CYLINDER HEAD COVER Remove the 4 nuts and No. 2
cylinder h...
9. DISCONNECT GROUND CABLE Remove the set bolt of the ground cable
from the engine left mounting bracket.
10. DISCONNECT B...
a. Remove the bolt.
b. Install the 2 No. 1 engine hangers with the bolts in the correct direction.
Parts No.: No. 1 engine...
e. Remove the suspension member.
19. JACK UP TRANSAXLE SLIGHTLY Using a transmission jack, support
the transaxle.
20. DISC...
22. REMOVE STARTER
a. Remove the bolt, starter cover and starter. Torque: 39 Nm (400
kgf-cm, 29 ft. lbs.)
b. Disconnect th...
Front wheel alignment.
Do the road test.
© 2010 ALLDATA LLC. All rights reserved.
Terms of Use
Page 8 of 8ALLDATA Online -...
Upcoming SlideShare
Loading in...5
×

2010 04-09 093445-clutch

212

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
212
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
2
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

2010 04-09 093445-clutch

  1. 1. Home | Account | Contact ALLDATA | Log Out | Help PAUL REDEHOFT Select Vehicle | New TSBs | Technician's Reference Component Search: OK Conversion Calculator 2001 Toyota Echo L4-1.5L (1NZ-FE) Vehicle Level Transmission and Drivetrain Manual Transmission/Transaxle Service and Repair Removal and Installation Removal and Installation Notes Zoom Sized for Print Page 1 of 8ALLDATA Online - 2001 Toyota Echo L4-1.5L (1NZ-FE) - Removal and Installation 4/9/2010http://www.alldatapro.com/alldata/PRO~V160195684~C41201~R0~OD~N/0/80851247/83...
  2. 2. REMOVAL 1. REMOVE HOOD HINT: At the time of installation, please refer to the following item. Adjust the hood. 2. REMOVE WIPER ARM HINT: At the time of installation, please refer to the following item. Adjust the installation position of the wiper arms. Zoom Sized for Print Page 2 of 8ALLDATA Online - 2001 Toyota Echo L4-1.5L (1NZ-FE) - Removal and Installation 4/9/2010http://www.alldatapro.com/alldata/PRO~V160195684~C41201~R0~OD~N/0/80851247/83...
  3. 3. 3. REMOVE RH AND LH COWL TOP VENTILATOR LOUVERS 4. REMOVE NO. 2 CYLINDER HEAD COVER Remove the 4 nuts and No. 2 cylinder head cover. Torque: 7.0 Nm (71 kgf-cm, 62 inch lbs.) 5. REMOVE BATTERY AND AIR CLEANER CASE ASSEMBLY WITH AIR HOSE 6. DISCONNECT WIRE HARNESS FROM TRANSAXLE Remove the set bolt of the wire harness clamp. 7. DISCONNECT CONTROL CABLE a. Remove the 2 clips and washers. b. Remove the 2 clips and disconnect the control cables from the transaxle. 8. DISCONNECT CLUTCH RELEASE CYLINDER a. Remove the set bolt of the clutch line. Torque: 4.9 Nm (50 kgf-cm, 43 inch lbs.) b. Remove the 2 set bolts of the clutch release cylinder. Torque: 12 Nm (120 kgf-cm, 9 ft. lbs.) Zoom Sized for Print Zoom Sized for Print Page 3 of 8ALLDATA Online - 2001 Toyota Echo L4-1.5L (1NZ-FE) - Removal and Installation 4/9/2010http://www.alldatapro.com/alldata/PRO~V160195684~C41201~R0~OD~N/0/80851247/83...
  4. 4. 9. DISCONNECT GROUND CABLE Remove the set bolt of the ground cable from the engine left mounting bracket. 10. DISCONNECT BACK-UP LIGHT SWITCH AND VEHICLE SPEED SENSOR CONNECTORS 11. REMOVE 2 TRANSAXLE UPPER SIDE MOUNTING BOLTS Torque: 33 Nm (340 kgf-cm, 25 ft. lbs.) 12. REMOVE STARTER SET BOLT Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.) 13. ATTACH ENGINE SLING DEVICE TO ENGINE HANGER Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print Page 4 of 8ALLDATA Online - 2001 Toyota Echo L4-1.5L (1NZ-FE) - Removal and Installation 4/9/2010http://www.alldatapro.com/alldata/PRO~V160195684~C41201~R0~OD~N/0/80851247/83...
  5. 5. a. Remove the bolt. b. Install the 2 No. 1 engine hangers with the bolts in the correct direction. Parts No.: No. 1 engine hanger: 12281-21010 Bolt: 91642-81025 Torque: 40 Nm (400 kgf-cm, 29 ft. lbs.) c. Attach the engine chain hoist to the engine hangers. CAUTION: Do not attempt to hang the engine by hooking the chain to any other part. 14. RAISE VEHICLE CAUTION: Make sure that the vehicle is securely supported. 15. REMOVE LH ENGINE UNDER COVER 16. DRAIN TRANSAXLE OIL Oil grade: API GL-4 or GL-5 Viscosity: SAE 75W-90 Capacity: 1.9 liters (2.0 US qts, 1.7 Imp. qts) Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.) 17. REMOVE RH AND LH FRONT DRIVE SHAFTS 18. REMOVE SUSPENSION MEMBER a. Remove the 2 set nuts and bolt of the engine rear mounting insulator from the suspension member. b. Disconnect the sliding yoke. c. Power steering: Disconnect the pressure feed and return tubes. d. Power steering: Disconnect the tube clamp. Zoom Sized for Print Zoom Sized for Print Page 5 of 8ALLDATA Online - 2001 Toyota Echo L4-1.5L (1NZ-FE) - Removal and Installation 4/9/2010http://www.alldatapro.com/alldata/PRO~V160195684~C41201~R0~OD~N/0/80851247/83...
  6. 6. e. Remove the suspension member. 19. JACK UP TRANSAXLE SLIGHTLY Using a transmission jack, support the transaxle. 20. DISCONNECT ENGINE LEFT MOUNTING BRACKET FROM ENGINE LEFT MOUNTING INSULATOR Remove the 2 bolts. Torque: 49 Nm (500 kgf-cm, 36 ft. lbs.) 21. REMOVE ENGINE REAR MOUNTING INSULATOR AND BRACKET a. Remove the bolt, nut and engine rear mounting insulator. Torque: 64 Nm (650 kgf-cm, 47 ft. lbs.) b. Remove the 3 bolts and engine rear mounting bracket. Torque: 49 Nm (500 kgf-cm, 36 ft. lbs.) Zoom Sized for Print Zoom Sized for Print Page 6 of 8ALLDATA Online - 2001 Toyota Echo L4-1.5L (1NZ-FE) - Removal and Installation 4/9/2010http://www.alldatapro.com/alldata/PRO~V160195684~C41201~R0~OD~N/0/80851247/83...
  7. 7. 22. REMOVE STARTER a. Remove the bolt, starter cover and starter. Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.) b. Disconnect the starter connector. c. Remove the nut and starter wire. 23. REMOVE 5 TRANSAXLE LOWER SIDE MOUNTING BOLTS Torque: 33 Nm (340 kgf-cm, 25 ft. lbs.) 24. REMOVE TRANSAXLE Lower the engine left side and remove the transaxle from the engine. HINT: At the time of installation, please refer to the following items. Align the input shaft with the clutch disc and install the transaxle to the engine. Temporarily tighten the transaxle mounting bolts. INSTALLATION Installation is in the reverse order of removal. HINT: After installation, check and inspect items as follows. Zoom Sized for Print Zoom Sized for Print Page 7 of 8ALLDATA Online - 2001 Toyota Echo L4-1.5L (1NZ-FE) - Removal and Installation 4/9/2010http://www.alldatapro.com/alldata/PRO~V160195684~C41201~R0~OD~N/0/80851247/83...
  8. 8. Front wheel alignment. Do the road test. © 2010 ALLDATA LLC. All rights reserved. Terms of Use Page 8 of 8ALLDATA Online - 2001 Toyota Echo L4-1.5L (1NZ-FE) - Removal and Installation 4/9/2010http://www.alldatapro.com/alldata/PRO~V160195684~C41201~R0~OD~N/0/80851247/83...

×