Isolation Valve Senator Libya
Upcoming SlideShare
Loading in...5
×

Like this? Share it with your network

Share
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
  • Get a customised B2B digital marketing solutions from VALVE SOLUTIONS. visit us and drop us your valuable enquiries for a special promotional offer.
    Are you sure you want to
    Your message goes here
  • nice tutorial.better to simplify with application and design consideration into a ppt is appreciable
    Are you sure you want to
    Your message goes here
    Be the first to like this
No Downloads

Views

Total Views
1,767
On Slideshare
1,767
From Embeds
0
Number of Embeds
0

Actions

Shares
Downloads
124
Comments
2
Likes
0

Embeds 0

No embeds

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
    No notes for slide

Transcript

  • 1. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 SC-GCM-95 CM Issue 2 © Copyright 2005 Spirax-Sarco Limited Module 12.2 Isolation Valves - Rotary Movement The Steam and Condensate Loop 12.2.1
  • 2. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 Rotary Movement Valves Rotary movement valves, often called quarter-turn valves, include ball valves and butterfly valves. Regardless of the type of rotary movement valve, the obturator rotates about an axis perpendicular to the direction of flow. Fluid may flow through the obturator, as is the case with ball valves, or around it, as with butterfly valves. Rotary movement valves tend to have a simple operating mechanism and are therefore easy to automate and maintain. Ball valves Ball valves were developed during World War II and were initially intended for use in aircraft fuel systems, where weight and space are at a premium. They consist of a body which houses a rotating ball which has an orifice or bore machined directly through it. The ball is located in the body by two sealing rings. Rotation of the ball through 90° opens and closes the valve and allows fluid to flow directly through the orifice. In the closed position, the blank sides of the ball block the inlet and the outlet preventing any flow. There are two basic designs of ball valves – the floating ball design, which relies on the valve seats to support the ball, and the trunnion mounted ball, which uses a trunnion to support the ball. Trunnion mounting is used on larger valves, as it can reduce the operating torque to about two-thirds of that provided by a floating ball. Conventionally, the handle that is attached to the ball is in-line with the axis of the pipe when the valve is open; conversely, if it is at right angles to the pipe axis, this indicates that the valve is closed. End view of the ball within the valve at different stages of rotation Stem seals Valve Valve Valve Stem fully open ½ open fully closed Ball Fluid passes freely through the orifice Seals Fig. 12.2.1 Ball valve (shown in its open position) Ball valves are available as reduced bore or full bore. Full bore valves have an orifice that is the same size as the diameter of the pipe, whereas in reduced bore valves, the orifice diameter is less than that of the pipe. Full bore valves cost more than reduced bore valves, and they should be used where the pressure drop across the valve is critical or where ball valves are used upstream of flowmeters. Full bore valves can be used in flowmeter applications to minimise fluid turbulence upstream of the measuring device. In order to insert the ball into the body, three different types of assembly exist. Not only does the type affect the ease of assembly, but it also influences the maintainability of the valve. 12.2.2 The Steam and Condensate Loop
  • 3. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 o Two and three piece valves - The body of the valve is split in one or two places in the same plane as the valve flange, and these pieces are bolted together. This has the advantage of simplified, in-line maintenance. o Top entry valves - The ball is inserted through a bonnet in the top of the valve. This facilitates in-line maintenance. o Single piece valves - The ball is enclosed in the body by an insert fitted along the valve’s axis. This eliminates the possibility of body joint leakage and any chance of disconnection whilst in service, but when maintenance is required, the whole valve has to be removed from the pipeline. (a) Single piece ball valve (b) Three piece ball valve (c) Two piece ball valve Fig. 12.2.2 Single piece (a) three piece (b) two piece (c) ball valves The Steam and Condensate Loop 12.2.3
  • 4. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 The choice of seat material determines the conditions for which a particular ball valve is most suited. Although new seat materials are continually being developed, Table 12.2.1 lists some of the more common materials in use today. Table 12.2.1 Common ball valve seat materials Application Seat material Maximum operating temperature PTFE 200°C Low temperatures Carbon reinforced PTFE 230°C High pressures Polyetheretherketone (PEEK) 250°C High temperatures Metal 1 000°C Ball valve options Ball valves can be produced with a number of options to meet the demands of a wide variety of applications: o Actuators - Ball valves, and indeed all rotary valves, are suitable for automation. This is usually accomplished by using either an electrically or pneumatically operated actuator. The actuator is connected to the valve through a linkage kit. Although not essential, an ISO standard mounting pad enables the linkage kit to be installed without dismantling the valve, which maintains valve integrity. Refer to Module 6.6 for more information on actuators. o Firesafe - As ball valves are commonly used in gas and oil pipelines, it is essential that the valves used in such applications are firesafe. A valve is considered firesafe if, when exposed to fire conditions, it will continue to provide minimal leakage through the seat and stem, and provide effective shut-off during or following a fire or exposure to excessive temperatures. Standards relating to fire-safety are set out in BS 6755 and API RP 6FA. The main concern is that burning temperatures will destroy soft seats and seals; a number of methods have been developed to overcome this. One approach is to include secondary metal sealing surfaces behind the polymeric seats as an integral part of the body. When exposed to burning temperatures, the seat begins to deform and the pressure of the process media displaces the ball so that it extrudes the polymeric seat (Figure 12.2.3(b)). When the seat has been completely destroyed, the ball will seat against the body metal sealing surface, providing a tight shut-off (Figure 12.2.3(c)). PTFE Body seal Ball (a) (b) (c) PTFE seal intact PTFE seal melting PTFE seal destroyed and a metal-to-metal seal is established Fig. 12.2.3 Operation of a firesafe ball valve In addition to the inherent safety of the seating mechanism, the stem seal must also be capable of preventing leakage to atmosphere under ‘fire’ conditions. This can be achieved by using high temperature seals made from flexible graphite or Grafoil®; alternatively, a bellows sealed arrangement can be used (see Figure 12.2.4). 12.2.4 The Steam and Condensate Loop
  • 5. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 Flexible linkage from drive to valve Bellows Fig. 12.2.4 A bellows sealed ball valve o Clean steam valves - A number of applications exist that require the valve to be of a ‘clean’ design; these include steam applications where there is direct injection of steam into the product and process fluid lines in the biotechnology, food and electronics industries. The main area of concern in such applications is the space between the body and the ball; process fluid may accumulate in these spaces leading to contamination and corrosion. This can be overcome by inserting cavity fillers in these spaces. The cavity filler may be an integral part of the seat or a separate component in the valve assembly. Furthermore, ball valves used in clean steam applications should be made from stainless steel with a good surface finish (less than 81 microns Ra is recommended). o Throttling applications - When ball valves are used in throttling applications, high velocity flow can impinge against a localised area of the ball and seals, causing premature deterioration of the seating material. Modifications to the standard design are required for ball valves to be used for throttling; these include the use of metal seats, hard coatings and, sometimes, modifications to the ball, to give a characterised flow pattern. The Steam and Condensate Loop 12.2.5
  • 6. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 Butterfly valves Although there are many different designs of butterfly valve, they all consist of a disc that rotates on a shaft at right angles to the fluid flow. When open, the disc is edge-on to the flow and the fluid passes around it, offering limited resistance. In the closed position, the disc is rotated against a seat in the body of the valve. Butterfly valves usually take up little more room than a pair of pipe flanges, and are therefore an attractive alternative to the ball valve where space is limited. In fact, some butterfly valves are designed specifically for insertion between pipe flanges, these are known as wafer butterfly valves. Fig. 12.2.5 Butterfly valves The main disadvantage of butterfly valves is that the shut-off is not as tight as that achieved by other valve types. This can be alleviated to an extent by offsetting the axis of rotation of the disc and using pressure assisted seats. By using an offset axis of rotation, a ‘camming’ action is generated, which means that the disc creates a tight seal with the seat during the last few degrees of shut-off. These high performance or eccentric-type butterfly valves have improved shut-off capabilities and their design enables them to be used for throttling. For steam applications, butterfly valves have largely been superseded by ball valves. Butterfly valves are more commonly used in liquid systems or where space is limited. The compactness of butterfly valves means less material is required and they are therefore ideal where the application specifies the use of costly materials, for example, in seawater applications where nickel is specified. 12.2.6 The Steam and Condensate Loop
  • 7. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 Selection and sizing of isolation valves A process fluid must be fully contained in a properly designed piping system to avoid endangering personnel and the environment, and contamination of the fluid itself. The pipeline system can have many potential leak paths, such as pipe joints, seams, equipment connections and, most importantly, valves. Valves can be one of the biggest contributors to plant problems if they are wrongly selected or are poorly designed or manufactured. Furthermore, a valve, when selected correctly for the application should last at least the life of the plant, if maintained properly. When selecting an isolating valve for a particular application, a number of factors need to be considered; these are shown in Table 12.2.2, along with the valve selection parameter that is affected. Table 12.2.2 Factors affecting the selection of an isolation valve Factors affecting the selection Areas of concern Affected parameter of an isolation valve Fluid – liquid or gas Pressure Type of valve Temperature Material of construction Process medium Flowrate Maintainability Corrosive Valve size Abrasion Speed of operation Fails – safe Functional requirements Type of valve Frequency of operation Emission loss to atmosphere Manual Pneumatic Type of valve Method of operation Electric Type of actuator Electropneumatic Hydraulic Valve size Pipeline material End connections Pipeline Pipeline size Type of valve Pressure loss Material of construction Availability Firesafe Special requirements Free draining Cost Type of valve Antistatic Table 12.2.3 summarises the main characteristics of the different types of isolation valve. Table 12.2.3 Typical sizes and operating ranges of isolation valves Pressure Temperature Pressure Size range range drop1 Valve type Min. Max. Min. Max. Min. Max. bar (mm) (mm) (bar) (bar) (º C) (º C) Gate 3 2 250 >0 700 -196 675 0.007 Globe 3 760 >0 700 -196 650 0.590 Diaphragm 3 610 >0 21 -50 175 0.021 Ball (full bore) 6 1 220 >0 525 -55 300 0.007 Butterfly 50 1 830 >0 102 -30 538 0.120 1 Note: Typical values for a DN150 bore valve passing saturated steam at 24 bar, flowing at 40 m / s. The Steam and Condensate Loop 12.2.7
  • 8. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 Table 12.2.4 summarises the applications of the most common isolating valve types in use today. Table 12.2.4 Applications of isolating valve types Valve type General applications Actuation Remarks Usually manual, but may be: Usually applied to higher Shut-off/ regulation - Electric pressure or high volume Globe valve of liquid / gas flow. - Manual systems, due to cost. Steam and condensate - Hydraulic Less suitable for viscous applications. - Pneumatic or contaminated fluids. Used fully open or fully closed for on /off regulation Usually manual, but may be: Usually used where the on steam, gas and other - Electric valve body is to be Piston valve fluid services. Typically - Manual permanently installed and used on fluids that cause - Hydraulic maintenance needs to excessive seat wear. be minimised. Not recommended as a Normally used fully open Usually manual, but may be: throttling valve. Solid or fully closed for on /off - Electric wedge gate is free from Gate valve regulation on water, oil, - Manual chatter and jamming. gas, steam and other fluid - Hydraulic Parallel slide valve used in services. steam systems. Relatively simple Shut-off and regulation in Handwheel construction. Can be larger pipelines in Electric motor produced in very large sizes. Butterfly valve waterworks, process Pneumatic actuator Eccentric design essential industries, HPI, power Hydraulic actuator for steam systems. generation. Air motor Typically used on liquid systems. Wide range of applications Handwheel in all sizes, including HPI. Electric motor Can handle all fluid types. Ball Valve Limited maximum pressure Steam and condensate Pneumatic actuator applications. Hydraulic actuator rating. Table 12.2.5 is a generalised guide to the selection of isolation valves for particular steam and condensate applications. It should be noted that the choice of isolation valve is subjective and different industries and those in different geographical regions have their own unique preferences. Table 12.2.5 Selection of valves for steam/ condensate isolation purposes Note: In this table, bellows sealed refers to a bellows sealed globe valve and globe refers to a standard, gland packed globe valve. Standard Dead tight Energy and Application Choice Zero emissions application shut-off maintenance savings <DN50 Ball < DN25 Piston < DN25 Piston Bellows sealed 1st >DN50 Globe >DN25 Ball >DN25 Ball Globe Trap sets < DN50 Ball up to 100 mm < DN25 Piston 2nd >DN50 Bellows Bellows sealed Bellows sealed >DN25 Ball sealed Mains and 1st Globe Ball Piston Bellows sealed equipment < 50 mm 2nd Ball Piston Bellows sealed Piston Mains and 1st Bellows sealed Bellows sealed Bellows sealed Bellows sealed equipment 50 mm - 100 mm 2nd Globe Ball Ball Ball Mains and 1st Bellows sealed Bellows sealed Bellows sealed Bellows sealed equipment > 100 mm 2nd Globe Globe Globe Globe Automated 1st Bellows sealed Bellows sealed Bellows sealed Bellows sealed mains and equipment 2nd Globe Ball Ball Ball 12.2.8 The Steam and Condensate Loop
  • 9. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 Once the most suitable type of valve has been chosen, it is necessary to choose the correct size. Valves are typically sized according to the pipeline size. It is however advisable to check that the pressure drop across the valve (when it is fully open) is within acceptable limits. The pressure drop is a function of the valve flow coefficient (or Kvs value), the flowrate and the inlet pressure. Specification sheets usually contain data about the Kvs value when the valve is fully opened. With knowledge of the typical operating pressure, and the mass flowrate, it is possible to determine the pressure drop across a chosen valve. Alternatively, if the maximum acceptable pressure drop is known, it is possible to select a suitable valve size. Although there are many formulae and charts available to predict the relationship between flowrate and pressure drop, the following simplified empirical formula (Equation 3.21.1) produces reliable results for steam and is therefore commonly used: ÇVÃÃ2ÃÃ !ÃF Y ÃQ ÃÃ$%&#!ÃÃ F Ã Equation 3.21.2 Where: ms = Mass flowrate in kg / h Kv = Valve flow coefficient P1 - P2 c = Pressure drop ratio = P1 P1 = Upstream pressure in bar absolute P2 = Downstream pressure in bar absolute This formula forms the basis of the chart shown in Figure 12.2.7, which was first introduced in Block 3, Module 21. If the isolating valve is to be used in a liquid system, the pressure drop across the valve is determined using the following equation: B F Y Ã2ÃÃÆÃ 'Q Equation 6.3.1 Where: Kv = Valve flow coefficient (m³ / h bar) V = Flowrate in m³ / h (m³ / h) G = Relative density of liquid (non-dimensional) DP = Pressure drop across the valve in bar (bar) Rearranging the formula gives:  'QÃÃ2ÃÃB ⎛ FÆ ⎞ ⎜ Y⎟ Equation 12.2.1 ⎝ ⎠ The Steam and Condensate Loop 12.2.9
  • 10. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 This sizing chart is empirical and should not be used for critical applications 0.8 Inlet pressure bar a (absolute) 1 2 Cr 3 Pr itic es al pre 4 su ss re ure 5 dr dro op pl ba ine 8 r 10 20 0. 2 3 0. 0. 0. 2 5 5 1 3 1 30 40 50 10 20 80 30 20 30 Steam flow kg/h (÷ 3 600 = kg/s) 40 50 80 0.4 100 Kv = 1.0 200 1.6 300 2.5 400 4.0 500 6.3 Kv 800 = 10 1 000 16 25 2 000 40 3 000 63 4 000 Kv = 10 5 000 0 16 0 8 000 25 0 10 000 40 0 20 000 30 000 40 000 50 000 80 000 100 000 Fig. 12.2.6 Saturated steam sizing chart 12.2.10 The Steam and Condensate Loop
  • 11. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 1 000 5) In what book of the Bible do you find these words, ) y I am the living bread which came down from heaven 200 500 400 100 Kv 0 0 300 10 200 50 5000 40 40 300 30 100 by a whirlwind? 00 y 2 20 50 100 40 10 30 50 40 20 30 5 4 20 3 10 10 2 Water flow m³ /h 5 Water flow l/s 4 5 4 1 3 3 2 2 0.5 0.4 1 0.3 1 0.2 0.5 0.4 0.5 0.3 0.4 0.1 0.3 0.2 0.2 0.1 0.05 0.04 5 0.03 0.1 0.0 4 0.0 3 0.02 0.0 2 0.05 0.0 0.04 0.01 0.03 1 0.0 0.02 0.005 0.004 0.003 0.01 1 2 3 4 5 10 20 30 40 50 100 200 300 500 1 000 2 000 4 000 Pressure drop kPa Fig. 12.2.7 Water sizing chart The Steam and Condensate Loop 12.2.11
  • 12. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 Questions 1. Which of the following situations would warrant the use of a full bore ball valve? a| Upstream of a flowmeter ¨ b| For isolation of plant when cost is an important consideration ¨ c| After a steam trap set ¨ d| The end of a steam main ¨ 2. What is the main advantage of a three piece ball valve over a one piece ball valve? a| Eliminates the chance of disconnections whilst in service ¨ b| Each piece can be selected individually to customise the valve to suit a unique application ¨ c| Higher valve integrity ¨ d| Easier in-line maintenance ¨ 3. Which application would a standard butterfly valve be most suitable for? a| Temperature control ¨ b| In small mains applications ¨ c| Automated isolation of a large steam jacket ¨ d| In hazardous gas applications that require a dead tight seal ¨ 4. What would be the Kv value of a steam isolation valve with a pressure drop of 0.3 bar? Given that it is to be used upstream of a heat exchanger with a steam demand of 3 000 kg / h and a supply pressure of 5 bar g. a| 70 ¨ b| 88 ¨ c| 100 ¨ d| 420 ¨ 5. A bellows sealed globe valve is available in sizes DN25, DN32, DN40 and DN50 and the table below shows the corresponding Kvs values? Size DN25 DN32 DN40 DN50 Kvs value 12 20 30 47 Choose the correct size globe valve if it is to be used downstream of a pressure reducing station passing 500 kg / h of steam at 10 bar a, given that the pressure drop across the chosen globe valve must be less than 0.1 bar. a| DN25 ¨ b| DN32 ¨ c| DN40 ¨ d| DN50 ¨ 12.2.12 The Steam and Condensate Loop
  • 13. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 6. Using selection tables determine the most suitable types of valve for use on a 150 mm steam main to give a dead tight shut-off? a| Bellows sealed globe valve / globe valve ¨ b| Ball valve / bellows sealed valve ¨ c| Ball valve / piston valve ¨ d| Bellows sealed globe valve / eccentric butterfly valve ¨ Answers 1: a, 2: d, 3: c, 4: b, 5: b, 6: a The Steam and Condensate Loop 12.2.13
  • 14. Block 12 Pipeline Ancillaries Isolation Valves - Rotary Movement Module 12.2 12.2.14 The Steam and Condensate Loop