NATIONAL COLLEGE OF SCIENCE AND TECHNOLOGY                        Amafel Building, Aguinaldo Highway Dasmariñas City, Cavi...
OBJECTIVES    Plot the gain-frequency response curve and determine the center frequency for an active band-      pass fil...
DATA SHEETMATERIALSOne function generatorOne dual-trace oscilloscopeTwo LM741 op-ampsCapacitors: two 0.001 µF, two 0.05 µF...
A higher value of Q means a narrower bandwidth and a more selective filter. A filter with a Q less than oneis considered t...
Figure 4-2 shows a second-order (two-pole) Sallen-Key notch filter. The expected center frequency (fO) canbe calculated fr...
Step 2         Run the simulation. Notice that the voltage gain has been plotted between the frequencies               of ...
Step 6      Based on the measured values of fC1 and fC2, calculate the bandwidth (BW) of the band-pass            filter. ...
 θ = 173.987oQuestion:         What does this result tell you about the relationship between the filter output and input ...
Question:   How did the measured voltage gain in the passband compare with the voltage gain            calculated from the...
CONCLUSION        Active is constructed with active devices such as op-amps combined with other passive elements.After con...
SAMPLE COMPUTATIONStep 3Step 4Step 4 QuestionStep 7Step 7 QuestionStep 8Step 9Step 9 QuestionStep 14Step 15Step 18Step 19S...
Upcoming SlideShare
Loading in...5
×

Comm008 e4 agdon

303

Published on

Published in: Business, Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
303
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
3
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Comm008 e4 agdon

  1. 1. NATIONAL COLLEGE OF SCIENCE AND TECHNOLOGY Amafel Building, Aguinaldo Highway Dasmariñas City, Cavite EXPERIMENT NO. 4 ACTIVE BAND-PASS AND BAND-STOP FILTERSAgdon, Berverlyn B. July 21, 2011Signal Spectra and Signal Processing/BSECE 41A1 Score: Engr. Grace Ramones Instructor
  2. 2. OBJECTIVES  Plot the gain-frequency response curve and determine the center frequency for an active band- pass filter.  Determine the quality factor (Q) and bandwidth of an active band-pass filter  Plot the phase shift between the input and output for a two-pole active band-pass filter.  Plot the gain-frequency response curve and determine the center frequency for an active band-stop (notch) filter.  Determine the quality factor (Q) and bandwidth of an active notch filter.
  3. 3. DATA SHEETMATERIALSOne function generatorOne dual-trace oscilloscopeTwo LM741 op-ampsCapacitors: two 0.001 µF, two 0.05 µF, one 0.1 µFResistors: one 1 kΩ, two 10 kΩ, one 13 kΩ, one 27 kΩ, two 54 kΩ, and one 100kΩTHEORYIn electronic communications systems, it is often necessary to separate a specific range of frequencies fromthe total frequency spectrum. This is normally accomplished with filters. A filter is a circuit that passes aspecific range of frequencies while rejecting other frequencies. Active filters use active devices such as op-amps combined with passive elements. Active filters have several advantages over passive filters. Thepassive elements provide frequency selectivity and the active devices provide voltage gain, high inputimpedance, and low output impedance. The voltage gain reduces attenuation of the signal by the filter, thehigh input impedance prevents excessive loading of the source, and the low output impedance preventsthe filter from being affected by the load. Active filters are also easy to adjust over a wide frequency rangewithout altering the desired response. The weakness of active filters is the upper-frequency limit due to thelimited open-loop bandwidth (funity) of op-amps. The filter cutoff frequency cannot exceed the unity-gainfrequency (funity) of the op-amp. Therefore, active filters must be used in applications where the unity-gainfrequency (funity) of the op-amp is high enough so that it does not fall within the frequency range of theapplication. For this reason, active filters are mostly used in low-frequency applications.A band-pass filter passes all frequencies lying within a band of frequencies and rejects all other frequenciesoutside the band. The low cut-off frequency (fC1) and the high-cutoff frequency (fC2) on the gain-frequencyplot are the frequencies where the voltage gain has dropped by 3 dB (0.707) from the maximum dB gain. Aband-stop filter rejects a band of frequencies and passes all other frequencies outside the band, and ofthen referred to as a band-reject or notch filter. The low-cutoff frequency (fC1) and high-cutoff frequency(fC2) on the gain frequency plot are the frequencies where the voltage gain has dropped by 3 dB (0.707)from the passband dB gain.The bandwidth (BW) of a band-pass or band-stop filter is the difference between the high-cutoff frequencyand the low-cutoff frequency. Therefore,BW = fC2 – fC1The center frequency (fo)of the band-pass or a band-stop filter is the geometric mean of the low-cutofffrequency (fC1) and the high-cutoff frequency (fC2). Therefore,The quality factor (Q) of a band-pass or a band-stop filter is the ratio of the center frequency (fO) and thebandwidth (BW), and is an indication of the selectivity of the filter. Therefore,
  4. 4. A higher value of Q means a narrower bandwidth and a more selective filter. A filter with a Q less than oneis considered to be a wide-band filter and a filter with a Q greater than ten is considered to be a narrow-band filter.One way to implement a band-pass filter is to cascade a low-pass and a high-pass filter. As long as thecutoff frequencies are sufficiently separated, the low-pass filter cutoff frequency will determine the low-cutoff frequency of the band-pass filter and a high-pass filter cutoff frequency will determine the high-cutoff frequency of the band-pass filter. Normally this arrangement is used for a wide-band filter (Q 1)because the cutoff frequencies need to be sufficient separated.A multiple-feedback active band-pass filter is shown in Figure 4-1. Components R1 and C1 determine thelow-cutoff frequency, and R2 and C2 determine the high-cutoff frequency. The center frequency (fo) can becalculated from the component values using the equationWhere C = C1 = C2. The voltage gain (AV) at the center frequency is calculated fromand the quality factor (Q) is calculated fromFigure 4-1 Multiple-Feedback Band-Pass Filter XBP1 XFG1 IN OUT 10nF C1 100kΩ R2 741 3 Vo 6 Vin 1kΩ 2 10kΩ 10nF R1 RL C2
  5. 5. Figure 4-2 shows a second-order (two-pole) Sallen-Key notch filter. The expected center frequency (fO) canbe calculated fromAt this frequency (fo), the feedback signal returns with the correct amplitude and phase to attenuate theinput. This causes the output to be attenuated at the center frequency.The notch filter in Figure 4-2 has a passband voltage gainand a quality factorThe voltage gain of a Sallen-Key notch filter must be less than 2 and the circuit Q must be less than 10 toavoid oscillation.Figure 4-2 Two pole Sallen-Key Notch Filter XBP1 XFG1 IN OUT 27kΩ 27kΩ R52 R/2 50nF 50nF 3 0.05µF C3 0.05µF C Vin C C 6 2 741 Vo RL 54kΩ 54kΩ 10kΩ 54kΩ 54kΩ R R3 0 R R R2 100nF 2C R1 10kΩ 13kΩ 0 0PROCEDUREActive Band-Pass FilterStep 1 Open circuit file FIG 4-1. Make sure that the following Bode plotter settings are selected. Magnitude, Vertical (Log, F = 40 dB, I = 10 dB), Horizontal (Log, F = 10 kHz, I = 100 Hz)
  6. 6. Step 2 Run the simulation. Notice that the voltage gain has been plotted between the frequencies of 100 Hz and 10 kHz. Draw the curve plot in the space provided. Next, move the cursor to the center of the curve. Measure the center frequency (fo) and the voltage gain in dB. Record the dB gain and center frequency (fo) on the curve plot.  fo = 1.572 kHz  AdB = 33.906 dB AdB 40dB 10 dB F (Hz) 100 10kQuestion: Is the frequency response curve that of a band-pass filters? Explain why.  It is a frequency response curve of a band-pass filter because the filter only let the frequencies from 100.219 Hz to 10 kHz to pass and block the other frequency.Step 3 Based on the dB voltage gain at the center frequency, calculate the actual voltage gain (AV)  AV = 49.58Step 4 Based on the circuit component values, calculate the expected voltage gain (AV) at the center frequency (fo)  AV = 50Question: How did the measured voltage gain at the center frequency compare with the voltage gain calculated from the circuit values?  They have a difference of 0.42. The percentage difference of the measured and calculated value is 0.84%Step 5 Move the cursor as close as possible to a point on the left of the curve that is 3 dB down from the dB gain at the center frequency (fo). Record the frequency (low-cutoff frequency, fC1) on the curve plot. Next, move the cursor as close as possible to a point on the right side of the curve that is 3 dB down from the center frequency (fo). Record the frequency (high- cutoff frequency, fC2) on the curve plot.  fC1 = 1.415 kHz  fC2 = 1.746 kHz
  7. 7. Step 6 Based on the measured values of fC1 and fC2, calculate the bandwidth (BW) of the band-pass filter.  BW = 0.331 kHzStep 7 Based on the circuit component values, calculate the expected center frequency (fo)  fo = 1.592 kHzQuestion: How did the calculated value of the center frequency compare with the measured value?  They have a difference of 0.02 kHz. The calculated and measured center frequencies have a difference of 1.27%.Step 8 Based on the measured center frequency (fo) and the bandwidth (BW), calculate the quality factor (Q) of the band-pass filter.  Q = 4.75Step 9 Based on the component values, calculate the expected quality factor (Q) of the band-pass filter.  Q=5Question: How did your calculated value of Q based on the component values compare with the value of Q determined from the measured fo and BW?  The percentage difference of the two is only 5.26% The difference is only 0.25. Therefore, they are almost equal.Step 10 Click Phase on the Bode plotter to plot the phase curve. Change the vertical initial value (I) to -270o and the final value (F) to +270o. Run the simulation again. You are looking at the phase difference (θ) between the filter input and output wave shapes as a function of frequency (f). Draw the curve plot in the space provided. θ o 270 o -270 f (Hz) 100 10kStep 11 Move the cursor as close as possible to the curve center frequency (fo), recorded on the curve plot in Step 2. Record the frequency (fo) and the phase (θ) on the phase curve plot.  fo = 1.572 kHz
  8. 8.  θ = 173.987oQuestion: What does this result tell you about the relationship between the filter output and input at the center frequency?  The phase result tells that the filters output is 173.987o (approximately 180o) out of phase with input.Active Band-Pass (Notch) FilterStep 12 Open circuit file FIG 4-2. Make sure that the following Bode plotter settings are selected. Magnitude, Vertical (Log, F = 10 dB, I = -20 dB), Horizontal (Log, F = 500 Hz, I = 2 Hz)Step 13 Run the simulation. Notice that the voltage gain has been plotted between the frequencies of 2 Hz and 500 Hz. Draw the curve plot in the space provided. Next, move the cursor to the center of the curve at its center point. Measure the center frequency (fo) and record it on the curve plot. Next, move the cursor to the flat part of the curve in the passband. Measure the voltage gain in dB and record the dB gain on the curve plot.  fo = 58.649 Hz  AdB = 4. dB AdB 10 -20 f (Hz) 2 500Question: Is the frequency response curve that of a band-pass filters? Explain why.  Yes, because the center frequency Is located at the lowest gain. Moreover, it blocks the frequencies lying in the band.Step 14 Based on the dB voltage gain at the center frequency, calculate the actual voltage gain (AV)  AV = 1.77Step 15 Based on the circuit component values, calculate the expected voltage gain in the passband.  AV = 1.77
  9. 9. Question: How did the measured voltage gain in the passband compare with the voltage gain calculated from the circuit values?  They are the same. There is a 0% difference.Step 16 Move the cursor as close as possible to a point on the left of the curve that is 3 dB down from the dB gain in the bandpass Record the frequency (low-cutoff frequency, fC1) on the curve plot. Next, move the cursor as close as possible to a point on the right side of the curve that is 3 dB down from dB gain in the passband. Record the frequency (high-cutoff frequency, fC2) on the curve plot.  fC1 = 46.743 Hz  fC2 = 73.588 HzStep 17 Based on the measured values of fC1 and fC2, calculate the bandwidth (BW) of the notch filter.  BW = 26.845 HzStep 18 Based on the circuit component values, calculate the expected center frequency (fo)  fo = 58.95HzQuestion How did the calculated value of the center frequency compare with the measured value?  The percentage difference of the calculated and measured center frequency is 0.51%.Step 19 Based on the measured center frequency (fo) and bandwidth (BW) , calculate the quality factor (Q) of the notch filter.  Q = 2.18Step 20 Based on the calculated passband voltage gain (Av), calculate the expected quality factor (Q) of the notch filter.  Q = 2.17Question: How did your calculated value of Q based on the passband voltage gain compare with the value of Q determined from the measured fo and BW?  The calculated and measure quality factor have 0.46% difference.
  10. 10. CONCLUSION Active is constructed with active devices such as op-amps combined with other passive elements.After conducting the experiment, I proved that the a band-pass filter passes frequencies lying within aspecific range and attenuates all other frequencies, its counterpart is the band-stop filters which blocks thefrequencies lying within a specific range and passes the other frequencies. The center frequency of theband-pass is at its highest gain while the band-stop is at its lowest gain. The quality factor is inversely proportional to the bandwidth and is the indication of the selectivityof the filter. If the Q or quality of a filter goes up, it becomes narrower and its bandwidth decreases.Bandwidth is the difference of the low-cutoff and high-cutoff frequency. Finally, the center frequency is thegeometric mean of the low-cutoff and high-cutoff frequency.
  11. 11. SAMPLE COMPUTATIONStep 3Step 4Step 4 QuestionStep 7Step 7 QuestionStep 8Step 9Step 9 QuestionStep 14Step 15Step 18Step 19Step 20

×