How to setup call blocking based off of incoming Caller's ANI
Block incoming Calls based off of ANI. (incoming or originat...
In our case, we apply this to dial-peers 1 and 2 on each voice gateway as these are the
incoming dial-peers for each locat...
Upcoming SlideShare
Loading in...5
×

How to setup call blocking based off of incoming caller's ani

391

Published on

Leading Cisco networking products distributor-3network.com

How to setup call blocking based off of incoming caller's ani

Published in: Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
391
On Slideshare
0
From Embeds
0
Number of Embeds
2
Actions
Shares
0
Downloads
4
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Transcript of "How to setup call blocking based off of incoming caller's ani"

  1. 1. How to setup call blocking based off of incoming Caller's ANI Block incoming Calls based off of ANI. (incoming or originating phone number): the following is an example of how to setup call blocking based off of incoming Caller's ANI. In this example, my voice enviornment consist of an 8.6 CUCM Pub with 3 Subscribers. I have three Cisco 2911 h.323 voice gateways with 1 PRI each. I put together this simple 3 step process based off of a Cisco Configuration guide. I tested it on my cell phone and a coupe of others and it worked great. Here are the three steps: Block Incoming Calls based off of ANI. The following configuration must be applied to each voice gateway. It is done in basically 3 steps: 1. Create a Translation Rule. Within the translation rule you will use the reject command followed by the pattern you wish to reject. In this case we use the entire phone number. router#conf t router(config)#voice translation-rule 1 router(config-xxx)#rule 1 reject /8055553538/ router(config-xxx)#rule 2 reject /4805557904/ Moving forward, you can continue to add rules to reject numbers as you see fit. example: router(config-xxx)#rule 3 reject /4805557905/ and so on. 2. Apply the Translation rule to a Translation Profile and give it a name. (This will be used to apply to the incoming Dial-peers.) router#conf t router(config)#voice translation-profile call_block router(config-xxx)#call-block disconnect-cause incoming call-reject in this case we named the Translation Profile "call_block" 3. Apply Translation Profile to incoming Dial-peers (only) on each router. router#conf t router(config)#dial-peer voice 1 pots router(config-xxx)#call-block translation-profile incoming call_block router(config-xxx)#call-block disconnect-cause incoming call-reject 1
  2. 2. In our case, we apply this to dial-peers 1 and 2 on each voice gateway as these are the incoming dial-peers for each location. Each dial-peer looks like this after configuration: (at least in our enviornment) dial-peer voice 1 pots call-block translation-profile incoming call_block call-block disconnect-cause incoming call-reject incoming called-number .T direct-inward-dial port 0/0/0:23 Hope this helps for anyone out there looking to block based off incoming numbers. It is referred from: https://supportforums.cisco.com/docs/DOC-25415 More related: Cisco router rules of nomenclature Enterprise router recommendation: Cisco 2911 router How To Recover Cisco Router Password The Difference of The Cisco Catalyst 2900 and Cisco Catalyst 1900 More Cisco products and Reviews you can visit: http://www.3anetwork.com/blog : 3Anetwork.com is a world leading Cisco networking products wholesaler, we wholesale original new Cisco networking equipments, including Cisco Catalyst switches, Cisco routers, Cisco firewalls, Cisco wireless products, Cisco modules and interface cards products at competitive price and ship to worldwide. Our website: http://www.3anetwork.com Telephone: +852-3069-7733 Email: info@3Anetwork.com Address: 23/F Lucky Plaza, 315-321 Lockhart Road, Wanchai, Hongkong 2

×