Your SlideShare is downloading. ×
Classification of power amplifiers
Upcoming SlideShare
Loading in...5
×

Thanks for flagging this SlideShare!

Oops! An error has occurred.

×
Saving this for later? Get the SlideShare app to save on your phone or tablet. Read anywhere, anytime – even offline.
Text the download link to your phone
Standard text messaging rates apply

Classification of power amplifiers

941
views

Published on


0 Comments
1 Like
Statistics
Notes
  • Be the first to comment

No Downloads
Views
Total Views
941
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
66
Comments
0
Likes
1
Embeds 0
No embeds

Report content
Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
No notes for slide

Transcript

  • 1. Classification Of Power Amplifiers• The power amplifiers are primarily divided into two categories• Audio-power amplifiers – also called the small signal power amplifiers, raise the power levels of signals that have audio-frequency range (20 Hz- 20 kHz).• Radio-power amplifiers – also called large signal power amplifiers raise the power level of signals that have radio frequency range. They amplify a specific frequency or narrow band of frequencies while rejecting all other frequencies
  • 2. Classification According To Mode of Operation• Transistor power amplifiers handle large signals. Many of them are driven so hard by the input large signal that collector current is either cut- off or is in saturation region during a large portion of the input cycle. So such amplifiers are generally classified according to their mode of operation. This classification is based on the amount of transistor bias and amplitude of the input signal. It takes into account the portion of the cycle for which the transistor conducts. They are classified as below:
  • 3. Class A Power Amplifiers• In this case, transistor is so biased that the output current flows for the entire cycle of the input signal. Thus the operating point is so selected that the transistor operates only over the linear region of its load line. So such an amplifier can amplify input signal of small amplitude. As the transistor operates over the linear portion of load line, the output waveform is exactly similar to input waveform. So class A amplifiers are characterised by a high fidelity of the output. Such amplifiers are used where freedom from distortion is prime aim.
  • 4. Class A Power Amplifiers• Operation is restricted only over a small central region of the load line so such amplifiers can be used for amplifying signals of small amplitude. Also ac power output per transistor is small. The maximum possible overall efficiency with resistive load is 25%. The maximum possible collector efficiency with resistive load is 50%. In case an output transformer is used, both of these efficiencies are 50%.
  • 5. Class B Power Amplifiers• In this case, the transistor bias and signal amplitude are such that output current flows only during positive half cycle of the input signal. At zero signals, the collector current is zero and no biasing system is required in class B amplifiers. The operating point is selected at collector cut-off voltage; Because of total absence of negative half cycle from the output the signal distortion is high. Zero signal input represents the best condition for class B amplifiers because of zero collectors current.
  • 6. Class B Power Amplifiers• The transistor dissipates more power with increase in signal strength. In comparison to class A amplifiers average current is less, power dissipation is less. So overall efficiency is increased. The theoretical efficiency in class B operation is about 78.5% while it is only 50% in class A operation.
  • 7. Class AB Power Amplifiers• An amplifier may be biased at a dc level above the zero base current level of class B power amplifiers and above one-half the supply voltage level of class A; this bias condition is class AB. Class AB operation still needs a push-pull connection to achieve a full output cycle, but the dc bias level is usually closer to zero base current level for better power efficiency. For class AB operation the output signal swing occurs between 180 degree and 360 degree and is neither class A nor class B operation.
  • 8. Class C Power Amplifiers• A class C power amplifier is biased for operation for less than 180 of the input signal cycle and will operate only with a tuned or resonant circuit which provides a full cycle of operation for the tuned or resonant frequency. Such power amplifiers are, therefore, employed in special areas of tuned circuits, such as radio or communications.
  • 9. Class D Power Amplifiers• Class D power amplifiers are designed to operate with digital or pulse type signals. Using digital techniques makes it possible to have a signal that varies over the entire cycle (using sample-and-hold-circuitry) to recreate the output from many pieces of input signal. The main advantage of class D power amplifiers is that it is on (using power) only for short intervals and the overall efficiency can practically be very high (above 90 degree).