0
Air Barrier Paper<br />Definition: <br />A sheet material used as both a vapor retarder and an air barrier. <br />What it’...
Attics are ventilated to allow water vapor to escape, and to keep the house cooler during the summer by preventing the bui...
 Gable vents are used to create a cross draft in a wind, and ridge vents are used to ventilate continuously along an entir...
 The roof turbine is another form of high-ventilation.</li></li></ul><li>Backhoe<br />A backhoe is a piece of excavating e...
Batter Boards<br />Batter Boards are a temporary frame built just outside the corner of an excavation to carry marks that ...
Brick Arches<br />Centering- Temporary framework for an arch, dome, or vault. <br />‘Arch with a keystone’. The arch below...
Soldier<br />Brick Bonds<br />Flemish Bond- Each course of brick consists of alternating headers and stretchers, with the ...
Brick Sizes<br />The brick below is half the size of the modular brick and it is used for decoration purposes.<br />The Br...
Bulldozer<br /><ul><li> A bulldozer is a crawler equipped with a substantial metal plate,  used to push large quantities o...
Code Requirements<br />7 ½”<br />11 ½”<br />My window opens to approximately 22 ½” x 34 ¾” and 9 ½” AFF. The area of openi...
ConcreteJoints<br />A control joint is an intentional, linear discontinuity in a structure or component, designed to form ...
Concrete Masonry Units<br />Concrete Masonry Units, or CMUs, are blocks of hardened concrete, with or without hollow cores...
Decorative Concrete Masonry Units<br />Painted CMU<br />Split Block<br />
Doors<br />Panel Door:<br />Top Rail<br />Panel<br />Lock Rail<br />Stile<br />Bottom Rail<br />Transom-A small window dir...
Electrical Components<br />Circuit Breaker: <br />A device for interrupting an electric circuit to prevent excessive curre...
Framing Elements<br />1<br />Sheathing<br />Subflooring<br />Floor Joist<br />Sill Plate<br />Sole Plate<br />Stud<br />To...
Framing Elements (continued)<br />8<br />7<br />5<br />9<br />10<br />6<br />12<br />
Front End Loader<br />A piece of excavating equipment with a large, broad scoop on the front. Primarily used to &quot;load...
Gypsum Board<br />An interior facing panel consisting of a gypsum core sandwiched between paper faces; also called drywall...
Heat Pump<br />Advantage: Rapid Response time.<br />Disadvantage: Relatively Noisy<br />Compressor: Contains the fan which...
Insulation<br />A material with a low thermal conductivity that is included in a building assembly for the purpose of redu...
Lintel<br />A beam that carries the load of a wall across a window or door.<br />
Mortar<br />The mortar joint below is beaded. It is a little under ½” thick and is tooled. It is found on the a column at ...
Oriented Strand Board (OSB)<br />A nonveneered panel product composed of long shreds of wood fiber oriented in specific di...
Plumbing<br />Drop-in sink<br />Lavatory- A basin, or bowl used for washing. Typical piping size of 1 ½” diameter. <br />W...
Plywood<br />Plywood is a wood panel composed of an odd number of layers of wood veneer bonded together under pressure. Th...
Radiant Barrier<br />
Rebar<br />½” diameter rebar. Referred to as #4 because it is 4 eigths of an inch. The Deformations on the surface of the ...
Steep Roof Drainage<br />Gutter: <br />A channel that collects rainwater and snow melt at the eave of a roof.<br />Downspo...
Steep Roof Materials<br />Shingle: A small unit of water resistant material nailed in overlapping fashion with many other ...
Steep Roof Shapes<br />Hip <br />Gable<br />Mansard<br />Gambrel<br />
Steep Roof Terms<br />Eave: Level, low edge of a roof.<br />Rake: sloping edge of a roof<br />Ridge: The level intersectio...
Stone<br />Coursed Ashlar<br />Random Ashlar<br />
Vapor Retarder<br />A layer of material intended to obstruct the passage of water vapor through a building assembly. This ...
Waterproofing<br />Liquid-applied membranes that cure in place are relatively easy to detail around penetrations and other...
Weep Hole<br />A small opening whose purpose is to permit drainage of water that accumulates inside a building component o...
Welded Wire Fabric<br />A group of steel rods welded together, used to reinforce concrete slabs. <br />
Windows<br />The pictures to the left and right are of the same window. It is an awning window because it is hinged at the...
Upcoming SlideShare
Loading in...5
×

Visual Dictionary - Plywood

413

Published on

Published in: Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
413
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
13
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Transcript of "Visual Dictionary - Plywood"

  1. 1. Air Barrier Paper<br />Definition: <br />A sheet material used as both a vapor retarder and an air barrier. <br />What it’s doing: <br />Here it is serving as a barrier against weather elements while renovations are completed.<br />
  2. 2. Attics are ventilated to allow water vapor to escape, and to keep the house cooler during the summer by preventing the buildup of solar heat conducted through the roofing and roof sheathing. It is advantageous to have both low and high vents.<br />Attic Ventilation<br />Gable Vent<br />Soffit Vent<br />Roof Turbine<br /><ul><li> Soffit vents are used for the required intake ventilation.
  3. 3. Gable vents are used to create a cross draft in a wind, and ridge vents are used to ventilate continuously along an entire roof.
  4. 4. The roof turbine is another form of high-ventilation.</li></li></ul><li>Backhoe<br />A backhoe is a piece of excavating equipment consisting of a digging bucket on the end of a two-part articulated arm. Backhoes are used to pick up and move fill. The bucket of the one shown is 17” wide.<br />
  5. 5. Batter Boards<br />Batter Boards are a temporary frame built just outside the corner of an excavation to carry marks that lie on the surface planes of the basement that will be built in the excavation. They are used to mark the outline of the house for excavation purposes.<br />
  6. 6. Brick Arches<br />Centering- Temporary framework for an arch, dome, or vault. <br />‘Arch with a keystone’. The arch below is a Roman arch. Here is its keystone<br />The arch to the left and above is an elliptical arch.<br />
  7. 7. Soldier<br />Brick Bonds<br />Flemish Bond- Each course of brick consists of alternating headers and stretchers, with the headers centered over the stretchers in intervening courses.<br />Header<br />Rowlock<br />Sailor<br />Running Bond- All stretchers. This one is laid in ½ bond.<br />
  8. 8. Brick Sizes<br />The brick below is half the size of the modular brick and it is used for decoration purposes.<br />The Brick above is w x 2 ¼”. x 7 ½” This brick is a modular brick and the width should be between 3 ½” and 3 5/8”. <br />
  9. 9. Bulldozer<br /><ul><li> A bulldozer is a crawler equipped with a substantial metal plate, used to push large quantities of soil, sand, rubble, etc. during construction work. </li></li></ul><li>Cladding<br />Wood Boards<br />Wood shingles are thin, tapered slabs of wood sawn from short pieces of tree trunk. <br />Stone<br />Wood Shingles<br />Brick<br />
  10. 10. Code Requirements<br />7 ½”<br />11 ½”<br />My window opens to approximately 22 ½” x 34 ¾” and 9 ½” AFF. The area of opening is almost 5 ½’ , which is well over the required 5’ of opening for bedrooms on the first floor. However, the minimum height opening in 24”, so my window does not meet IRC standards. The sill height is adequate, however, because IRC prescribes a 44” max AFF sill.<br />The IRC regulates that tread depth should be no less that 10”, and risers should be no more than 7 ¾”. The treads shown are 11 ½” and the risers are 7 ½” so they meet the building codes.<br />
  11. 11. ConcreteJoints<br />A control joint is an intentional, linear discontinuity in a structure or component, designed to form a plane of weakness where cracking can occur in response to various forces so as to minimize or eliminate cracking elsewhere in the structure.<br />Crack<br />Control Joint<br />An isolation joint is an intentional discontinuity in a concrete component which separates it from another building component to prevent cracking around the component. Here the control joint is separating a concrete slab from a brick column.<br />
  12. 12. Concrete Masonry Units<br />Concrete Masonry Units, or CMUs, are blocks of hardened concrete, with or without hollow cores, designed to be laid in the same manner as brick or stone; a concrete block. Generally their dimensions are 8” x 8” x 16”<br />The CMU in the picture to the left is 8” x 4” x 6”<br />
  13. 13. Decorative Concrete Masonry Units<br />Painted CMU<br />Split Block<br />
  14. 14. Doors<br />Panel Door:<br />Top Rail<br />Panel<br />Lock Rail<br />Stile<br />Bottom Rail<br />Transom-A small window directly above a door.<br />Sidelight- A tall, narrow window alongside a door.<br />Flush Exterior Door<br />
  15. 15. Electrical Components<br />Circuit Breaker: <br />A device for interrupting an electric circuit to prevent excessive current, as that caused by a short circuit, from damaging the apparatus in the circuit or from causing a fire.<br />Electrical Outlet: Areceptacle providing a place in a wiring system where current can be taken to run electrical devices.<br />Power Generator: A machine that converts mechanical energy into electricity to serve as a power source for other machines. <br />Service Panel: A panel distributes the electricity from wires to receptacles throughout the house.<br />
  16. 16. Framing Elements<br />1<br />Sheathing<br />Subflooring<br />Floor Joist<br />Sill Plate<br />Sole Plate<br />Stud<br />Top Plate<br />Ceiling Joist<br />Rafter<br />Roof Decking<br />Anchor Bolt<br />Stringer<br />2<br />3<br />4<br />11<br />
  17. 17. Framing Elements (continued)<br />8<br />7<br />5<br />9<br />10<br />6<br />12<br />
  18. 18. Front End Loader<br />A piece of excavating equipment with a large, broad scoop on the front. Primarily used to &quot;load&quot; material into or onto another type of machinery (dump truck, conveyor belt, feed-hooper, rail-car, etc.).<br />
  19. 19. Gypsum Board<br />An interior facing panel consisting of a gypsum core sandwiched between paper faces; also called drywall, plasterboard.<br />
  20. 20. Heat Pump<br />Advantage: Rapid Response time.<br />Disadvantage: Relatively Noisy<br />Compressor: Contains the fan which moves air across coils which contain refrigerant to change the temperature of the refrigerant. <br />
  21. 21. Insulation<br />A material with a low thermal conductivity that is included in a building assembly for the purpose of reducing heat flow through the assembly. Helps keep energy efficiency.<br />Batt/Blanket<br />Loose Fill<br />Foaming<br />Rigid Board<br />
  22. 22. Lintel<br />A beam that carries the load of a wall across a window or door.<br />
  23. 23. Mortar<br />The mortar joint below is beaded. It is a little under ½” thick and is tooled. It is found on the a column at a bank. The mortar type is most likely type S.<br />
  24. 24. Oriented Strand Board (OSB)<br />A nonveneered panel product composed of long shreds of wood fiber oriented in specific directions and bonded together under pressure.<br />Manufacturing Process:<br />The layers of OSB are laid so that the two outer layers have grains running in the same direction, and the inner layers run perpendicular. These layers are then dried, glued, and pressed together.<br />
  25. 25. Plumbing<br />Drop-in sink<br />Lavatory- A basin, or bowl used for washing. Typical piping size of 1 ½” diameter. <br />Water Closet<br />Typically a 3” diameter pipe<br />
  26. 26. Plywood<br />Plywood is a wood panel composed of an odd number of layers of wood veneer bonded together under pressure. The wood is rotary sliced off the tree, then dried to remove moisture, cut to size, glued in layers, and the pressed into boards. <br />Veneer- A thin layer, sheet, or facing.<br />
  27. 27. Radiant Barrier<br />
  28. 28. Rebar<br />½” diameter rebar. Referred to as #4 because it is 4 eigths of an inch. The Deformations on the surface of the rebar are to give it more surface space to adhere to concrete and grout, and to prevent slippage within the concrete.<br />
  29. 29. Steep Roof Drainage<br />Gutter: <br />A channel that collects rainwater and snow melt at the eave of a roof.<br />Downspout: <br />A vertical pipe for conducting water from a roof to a lower level<br />Splashblock: <br />A cement block located at the bottom of a downspout which prevents soil erosion at the opening.<br />
  30. 30. Steep Roof Materials<br />Shingle: A small unit of water resistant material nailed in overlapping fashion with many other such units to render a wall or sloping roof watertight. The ones to the left are metal. <br />Underlayment: A layer of waterproof material between roof sheathing and roofing. It protects from leakage and weather which may penetrate the roofing material.<br />Metal Panel Roof: Typically made of enamel-coated galvanized steel, copper, lead-coated copper, stainless steel, terne, and terne-coated stainless steel.<br />
  31. 31. Steep Roof Shapes<br />Hip <br />Gable<br />Mansard<br />Gambrel<br />
  32. 32. Steep Roof Terms<br />Eave: Level, low edge of a roof.<br />Rake: sloping edge of a roof<br />Ridge: The level intersection of roof planes at their highest point.<br />Valley: The sloping intersection of two roof planes.<br />Fascia: Board nailed to the lower ends of the rafters<br />Soffit: Encloses rafter tails.<br />House without a fascia board ( same house as on framing terms page, I am in the picture there)<br />Soffit<br />Ridge<br />Eave<br />Fascia<br />Rake<br />
  33. 33. Stone<br />Coursed Ashlar<br />Random Ashlar<br />
  34. 34. Vapor Retarder<br />A layer of material intended to obstruct the passage of water vapor through a building assembly. This one is attached to insulation. Generally, it is put on the warmer (warm in winter) side of the insulation. <br />
  35. 35. Waterproofing<br />Liquid-applied membranes that cure in place are relatively easy to detail around penetrations and other transitions, since in liquid state, the membrane can easily form itself to any shape.<br />The waterproofing on this building is protecting it from penetration by water that may seep through the soil. <br />
  36. 36. Weep Hole<br />A small opening whose purpose is to permit drainage of water that accumulates inside a building component or assembly.<br />
  37. 37. Welded Wire Fabric<br />A group of steel rods welded together, used to reinforce concrete slabs. <br />
  38. 38. Windows<br />The pictures to the left and right are of the same window. It is an awning window because it is hinged at the top and opens at the bottom. <br />The window to the right is a fixed window casement because it does not open.<br />The window above is a double hung window because it slides into an open position.<br />
  1. A particular slide catching your eye?

    Clipping is a handy way to collect important slides you want to go back to later.

×