Activy tecnologi and instructions

476 views

Published on

Published in: Education, Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
476
On SlideShare
0
From Embeds
0
Number of Embeds
3
Actions
Shares
0
Downloads
4
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Activy tecnologi and instructions

  1. 1. Tugas 2 praktek Konsep Routing 02 April 2013 POLITEKNIK NEGERI UJUNG PANDANG Praktek Konsep Routing Nurhikma 42511013 2b D4 TKJ Teknik elektro Dosen pembimbing : Irmawati, ST,MT 2013
  2. 2. Tugas 2 praktek Konsep Routing 02 April 2013 Activity Topology and Instructions In this section, the initial topology and instructions are shown for review purposes. Topology Network to Subnet 192.168.xx.0/24 Introduction : In this practice Packet Tracer Skills Exam, you will: • finish connecting the devices • design and implement an addressing scheme to meet stated requirements • configure, verify, and troubleshoot connectivity between all devices in the network Addressing Table Device Router1 Interface Fa0/0 Address 192.168.13.1/27 Subnet Mask 255.255.255.224 Default Gateway n/a Router1 Fa0/1 192.168.13.33/28 255.255.255.240 n/a Switch1 VLAN1 192.168.13.0/24 255.255.255.0 192.168.13.1/27 PC1 NIC 192.168.13.30/27 255.255.255.224 192.168.13.1/27 PC2 NIC 192.168.13.47/28 255.255.255.240 192.168.13.33/28
  3. 3. Tugas 2 praktek Konsep Routing 02 April 2013 Note: The initial network has some errors. To aid in configuring and verifying the devices as well troubleshooting the existing errors, use a printed version of these instructions to fill in the missing address information in the table during Step 2. Step 1: Connect the Devices. Connect the following devices using the appropriate cable: a. Connect PC1 to Switch1. b. Connect Switch1 to the Fa0/0 interface on RouterNamamhs. c. Connect Switch2 to the Fa0/1 interface on RouterNamamhs. d. Connect PC1 to the RouterNamamhs console port. Step 2: Determine the IP Addressing Scheme. Design an addressing scheme and fill in the Addressing Table based on the following requirements: a. Subnet the address space 172.16.1.0/24 to provide 30 host addresses for LAN 1 while wasting the least amount of address space. b. Assign the first available subnet to LAN 1. c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on RouterNamamhs. d. Assign the second address in this subnet to the VLAN 1 interface on Switch1. e. Assign the highest (last) host IP address in this subnet to PC1. f. Using the next available subnet, further subnet it to provide 10 host addresses for LAN2 while wasting the least amount of address space. g. Assign the lowest (first) host address in the LAN2 subnet to the Fa0/1 interface on RouterNamamhs. Result : IP = 172.16.1.0 (10101100.00010000.00000001.00000000) Netmask = 255.255.255.0 (11111111.11111111.11111111.00000000)
  4. 4. Tugas 2 praktek Konsep Routing 02 April 2013 Untuk 30 host terdapat biner 11110 Netmask = 11100000 (224) Jumlah host/subnet = 255-224 = 31 host. Subnet First host address Last host address Broadcast LAN I 172.16.1.0/24 172.16.1.1/27 172.16.1.30/27 172.16.1.32/27 LAN II 172.16.1.32/27 172.16.1.33/28 172.16.1.47/28 172.16.1.48/28 Device Router1 Interface Fa0/0 Address 172.16.1.1/27 Subnet Mask 255.255.255.224 Default Gateway n/a Router1 Fa0/1 172.16.1.33/28 255.255.255.240 n/a Switch1 VLAN1 172.16.1.0/24 255.255.255.0 PC1 NIC 172.16.1.30/27 255.255.255.224 172.16.1.1/27 172.16.1.1/27 PC2 NIC 172.16.1.47/28 255.255.255.240 172.16.1.33/28 Step 3: Configure RouterNamamhs. a. Configure RouterNamamhs with the following basic parameters: ⎬ The router name is RouterNamamhs. ⎬ The privileged EXEC mode uses the following encrypted password: class
  5. 5. Tugas 2 praktek Konsep Routing 02 April 2013 ⎬ Enable Telnet and console line login using the following password: cisco ⎬ Configure the banner message-of-the-day as Authorized access only! b. Configure the two Fast Ethernet interfaces, including addressing and a description. c. Close the terminal window after completing the router configuration. Step 4: Configure Switch1 and Verify Connectivity. a. Remove the console connection between PC1 and RouterNamamhs. b. Connect PC1 to the Switch1 console port. c. Configure Switch1 with the following basic parameters: ⎬ The switch name is Switch1
  6. 6. Tugas 2 praktek Konsep Routing 02 April 2013 ⎬ The privileged EXEC mode uses the following encrypted password: class ⎬ Enable Telnet and console line login using the following password: cisco ⎬ Configure the banner message-of-the-day as Authorized access only! d. Configure interface VLAN 1 and default gateway for Switch1. e. Switch1 should be able to ping the default gateway. Step 5: Configure and Verify PC1 Addressing. a. Using the IP addressing you determined in Step 2, configure PC1 with the correct addressing. b. PC1 should be able to ping the default gateway.
  7. 7. Tugas 2 praktek Konsep Routing 02 April 2013 Step 6: Verify and Troubleshoot End-to-End Connectivity. Verify that PC1 is able to ping PC2. If the ping fails, locate and correct any errors. For example, make sure PC2 is configured correctly with appropriate addressing for the subnet it belongs to.

×