CH 414
E
E
NGINE RING DRAW
E
ING

MUNAWAR ZAMAN BIN SHAHRUDDIN
Faculty of Chemical Engineering
Universiti Teknologi MARA (...
ISOM T
E RIC DRAW
ING
It should not be confused with 3D Solid model
drawing.
It is a 2D method of describing objects in
pi...
SE T
T ING ISOM T
E RIC SNAP
•

Before starting isometric drawing, must set Snap to isometric style:

•
•

Command: snap, ...
• The three isoplanes and isocircles.
Isoplane top

Iso
pla
ne
left

p
Iso

ht
rig
e
lan

4
Isometric Circles
• When drawing circles in isometric, the result will be an
ellipse.
• To ensure that the ellipse is an i...
To produce an isometric, it is advisable that you begin by sketching
out the isometric drawing complete with the vital dim...
E
xercise time! Class work.

7
8
ISOMETRIC TUTORIAL

There is an error in the stepby-step figure. You will find out
what the mistake is while
practicing wi...
ISOMETRIC TUTORIAL

There is an error in the stepby-step figure. You will find out
what the mistake is while
practicing wi...
Upcoming SlideShare
Loading in …5
×

W7 isometric drawing1

566 views
376 views

Published on

Published in: Technology, Education
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
566
On SlideShare
0
From Embeds
0
Number of Embeds
7
Actions
Shares
0
Downloads
7
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

W7 isometric drawing1

  1. 1. CH 414 E E NGINE RING DRAW E ING MUNAWAR ZAMAN BIN SHAHRUDDIN Faculty of Chemical Engineering Universiti Teknologi MARA (UiTM), Shah Alam Tel: 03-55436339/019-2490416 E-mail:munawar_zaman@salam.uitm.edu.my
  2. 2. ISOM T E RIC DRAW ING It should not be confused with 3D Solid model drawing. It is a 2D method of describing objects in pictorial form.
  3. 3. SE T T ING ISOM T E RIC SNAP • Before starting isometric drawing, must set Snap to isometric style: • • Command: snap, ENTER Specify snap setting or [On/OFF/Aspect…]: type in ‘s’ for style, ENTER Enter snap grid style [Standard/Isometric]: type ‘i’ for isometric, ENTER Specify vertical snap: Type 5, ENTER • • • • Check out the cursor hair line. It will now be set in isometric pattern. There 3 main positions when working in this setting. Use Ctrl-E or F5 to toggle between isometric top, iso-right or iso-left. 3
  4. 4. • The three isoplanes and isocircles. Isoplane top Iso pla ne left p Iso ht rig e lan 4
  5. 5. Isometric Circles • When drawing circles in isometric, the result will be an ellipse. • To ensure that the ellipse is an isometric circle every time Ellipse command is called, the setting “I” must be used. • Command: ellipse • Then type in “i” (for isocircle), ENTER • Specify radius:…. • Try to construct an isocircle at the 3 different positions (top, right, left). 5
  6. 6. To produce an isometric, it is advisable that you begin by sketching out the isometric drawing complete with the vital dimensions to give you an idea of how it would look like on AutoCAD. Once the sketch is confirmed, you are then ready to start drawing using the software. 6
  7. 7. E xercise time! Class work. 7
  8. 8. 8
  9. 9. ISOMETRIC TUTORIAL There is an error in the stepby-step figure. You will find out what the mistake is while practicing with this example exercise. 9
  10. 10. ISOMETRIC TUTORIAL There is an error in the stepby-step figure. You will find out what the mistake is while practicing with this example exercise. 9

×