F-15 Park Jet
3D Foamy
Specs:

Copyright © 2004 3DFoa
All rights reserved.
Designed and Drawn by:
Steve Shumate & Levi Jo
...
Jet
3DFoamy.com.
rved.
wn by:
Levi Jordan
04
Cut a "V" groove
in foam for
spars. Pull spar
through groove
to make round

CG INFO
Start with the recomended
CG range. Yo...
All hinging
tape or ac
points epo
and contro
nging for control surfaces can be packing
or actual hinges. I prefer robart hinge
s epoxied in place for the added longivi...
Sand the fuselage corners round
with 80 grit sand paper,
then finish smooth with 200 and 400
Depron Rails
Prototype Setup/Specs
6

5

4

Wing area: 289 sq in (effective area, which includ
Span: 28.4 in
Length: 41.7 in
Weight RTF...
s
ncludes the effect of the wing strakes)

wing area)

ico and Hitec HS-55 servos, 10 amp ESC
orizontal stabilizer, twin r...
Round LE, apply 3M 1" Satin tape for protection

Push/Pull

Pull Pull
Cut Control horns from 1/32"
ply or a plastic coffee...
Flight controls: Wing flaperons, full-flying horizo
Materials used: Either 6mm Depron or BlueCore
3

2

1
1

2

3

4

5

F...
orizontal stabilizer, twin rudders
Core fan fold foam
Vacu
(San
Vacuum Formed Canopy
(Sand from foam if scratch built)

www.3DFoam
Cut hatch after painting
for radio access

amy.com

Laser cut 1/4" birch motor block.
Epoxy into plane. DO NOT use
CA on t...
HS-56HB

k.
e
t.
F15 plans tiled(Foamy)
F15 plans tiled(Foamy)
F15 plans tiled(Foamy)
F15 plans tiled(Foamy)
F15 plans tiled(Foamy)
F15 plans tiled(Foamy)
F15 plans tiled(Foamy)
F15 plans tiled(Foamy)
F15 plans tiled(Foamy)
F15 plans tiled(Foamy)
Upcoming SlideShare
Loading in …5
×

F15 plans tiled(Foamy)

393 views
219 views

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
393
On SlideShare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
9
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

F15 plans tiled(Foamy)

  1. 1. F-15 Park Jet 3D Foamy Specs: Copyright © 2004 3DFoa All rights reserved. Designed and Drawn by: Steve Shumate & Levi Jo Updated: 0/19/2004 Weight 14-18 oz. Thrust 14-24 oz. Radio 4-5 Chanel Area 289.7 in2 Loading 6.5-8.6 oz/ft2 WWW.3DFOAMY.COM
  2. 2. Jet 3DFoamy.com. rved. wn by: Levi Jordan 04
  3. 3. Cut a "V" groove in foam for spars. Pull spar through groove to make round CG INFO Start with the recomended CG range. You can adjust it further back as you become more familiar with the jet.
  4. 4. All hinging tape or ac points epo and contro
  5. 5. nging for control surfaces can be packing or actual hinges. I prefer robart hinge s epoxied in place for the added longivity ontrol freeness. CA hinges work well also.
  6. 6. Sand the fuselage corners round with 80 grit sand paper, then finish smooth with 200 and 400
  7. 7. Depron Rails
  8. 8. Prototype Setup/Specs 6 5 4 Wing area: 289 sq in (effective area, which includ Span: 28.4 in Length: 41.7 in Weight RTF: 15.6 oz as shown Wing loading: 8.2 oz/ft2 (based on effective wing Motor: GWS EPS-350 with “C” gearing Battery: 11.1V 1200 mAh Lipo Prop: GWS 8x6 SF Current draw: 9.7 amps Power loading: 101 watts/lb Radio equipment: GWS R-6 receiver, GWS Pico a Flight controls: Wing flaperons, full-flying horizo Materials used: Either 6mm Depron or BlueCore
  9. 9. s ncludes the effect of the wing strakes) wing area) ico and Hitec HS-55 servos, 10 amp ESC orizontal stabilizer, twin rudders Core fan fold foam
  10. 10. Round LE, apply 3M 1" Satin tape for protection Push/Pull Pull Pull Cut Control horns from 1/32" ply or a plastic coffee can lid.
  11. 11. Flight controls: Wing flaperons, full-flying horizo Materials used: Either 6mm Depron or BlueCore 3 2 1 1 2 3 4 5 Foam Nose Cone (CNC Cut, Sanded to shape) 6
  12. 12. orizontal stabilizer, twin rudders Core fan fold foam Vacu (San
  13. 13. Vacuum Formed Canopy (Sand from foam if scratch built) www.3DFoam
  14. 14. Cut hatch after painting for radio access amy.com Laser cut 1/4" birch motor block. Epoxy into plane. DO NOT use CA on the moutor mount.
  15. 15. HS-56HB k. e t.

×