• Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Be the first to comment
    Be the first to like this
No Downloads

Views

Total Views
23
On Slideshare
0
From Embeds
0
Number of Embeds
1

Actions

Shares
Downloads
1
Comments
0
Likes
0

Embeds 0

No embeds

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
    No notes for slide

Transcript

  • 1. ccnav5.org http://ccnav5.org/ccna-3-chapter-7-v5-0-2014-exam-answers/?pfstyle=wp CCNAV5.Org CCNAv5.Org CCNA 3 Chapter 7 v5.0 2014 Exam Answers CCNA 3 Chapter 7 v5.0 2014 Exam Answers CCNA 3 Exam 2014 1 Place the options in the following order: first – not scored – third second 2 Refer to the exhibit. Which command should be used to configure EIGRP to only advertise the network that is attached to the gigabit Ethernet 0/1 interface? network 172.16.23.64 0.0.0.63* network 172.16.23.0 255.255.255.192 network 172.16.23.64 0.0.0.127 network 172.16.23.0 255.255.255.128 3 What is the purpose of using protocol-dependent modules in EIGRP? to accommodate routing of different network layer protocols* to identify different application layer protocols
  • 2. to describe different routing processes to use different transport protocols for different packets 4 Which statement describes a characteristic of the delivery of EIGRP update packets? EIGRP sends all update packets via unicast. EIGRP uses a reliable delivery protocol to send all update packets.* EIGRP uses UDP to send all update packets. EIGRP sends all update packets via multicast. 5 A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.) bandwidth* MTU delay* load reliability 6 Which protocol is used by EIGRP to send hello packets? RTP* TCP UDP IP 7 Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame? 01-00-5E-00-00-09 01-00-5E-00-00-10 01-00-5E-00-00-0A* 01-00-5E-00-00-0B 8 Place the options in the following order: – not scored –
  • 3. EIGRP for IPv4 only both EIGRP for IPv4 and EIGRP for IPv6 EIGRP for IPv6 only 9 Refer to the exhibit. R2 has two possible paths to the 192.168.10.4 network. What would make the alternate route meet the feasibility condition? a reported distance greater than 41024000 a feasible distance greater than 41024000 an administrative distance less than 170 a reported distance less than 3523840* 10 Refer to the exhibit. Which two networks contain feasible successors? (Choose two.) 192.168.51.0
  • 4. 10.44.101.252 10.44.104.253 10.44.100.252* 192.168.71.0* 11 If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable? 10 seconds 15 seconds* 20 seconds 30 seconds 12 Which command or commands must be entered on a serial interface of a Cisco router to restore the bandwidth to the default value of that specific router interface? shutdown no shutdown bandwidth 1500 copy running-config startup-config reload no bandwidth* 13 Which EIGRP route would have the preferred administrative distance? a summary route* an internal route an external route that is redistributed from RIP an external route that is redistributed from OSPF 14 How do EIGRP routers establish and maintain neighbor relationships? by comparing known routes to information received in updates by exchanging routing tables with directly attached routers by dynamically learning new routes from neighbors by exchanging hello packets with neighboring routers* by exchanging neighbor tables with directly attached routers 15 When an EIGRP-enabled router uses a password to accept routes from other EIGRP-enabled routers, which mechanism is used? EIGRP authentication* Diffusing Update Algorithm Reliable Transport Protocol bounded updates
  • 5. partial updates 16 What is indicated when an EIGRP route is in the passive state? The route has the highest path cost of all routes to that destination network. The route is a feasible successor and will be used if the active route fails. The route is viable and can be used to forward traffic.* There is no activity on the route to that network. The route must be confirmed by neighboring routers before it is put in the active state. 17 Which three metric weights are set to zero by default when costs in EIGRP are being calculated? (Choose three.) k6 k3 k5* k4* k2* k1 18 Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP? to send a manual summarization to exclude some interfaces from the EIGRP process* to subnet at the time of the configuration to lower the router overhead 19 Which table is used by EIGRP to store all routes that are learned from EIGRP neighbors? the adjacency table the routing table the topology table* the neighbor table 20 Where are EIGRP successor routes stored? only in the routing table in the routing table and the topology table* only in the neighbor table in the routing table and the neighbor table 21
  • 6. Launch PT – Hide and Save PT Open the PT Activity. Perform the tasks in the activity instructions and then answer the question. Which code is displayed on the web server? Done Complete* EIGRP IPv6EIGRP 22 Which command is used to display the bandwidth of an interface on an EIGRP-enabled router? show ip protocols show interfaces* show ip interface brief show ip route 23 Fill in the blank. In an EIGRP topology table, a route that is in a/an ” active ” state will cause the Diffusing Update Algorithm to send EIGRP queries that ask other routers for a path to this network.