• Share
  • Email
  • Embed
  • Like
  • Save
  • Private Content
Mini Cooper Owners Manual 2002
 

Mini Cooper Owners Manual 2002

on

  • 16,365 views

 

Statistics

Views

Total Views
16,365
Views on SlideShare
16,362
Embed Views
3

Actions

Likes
0
Downloads
99
Comments
0

2 Embeds 3

http://www.slideshare.net 2
http://www.facebook.com 1

Accessibility

Categories

Upload Details

Uploaded via as Adobe PDF

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

    Mini Cooper Owners Manual 2002 Mini Cooper Owners Manual 2002 Presentation Transcript

    • OWNER'S MANUAL MINI COOPER Contents MINI COOPER S From A to Z Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CONGRATULATIONS ON YOUR NEW MINI This Owner's Manual should be considered a permanent part of this vehicle. It should stay with the vehicle when sold to provide the next owner with important operating, safety and maintenance information. This manual is supplemented by a Service and Warranty Information Booklet for US models or a Warranty and Service Guide Booklet for Canadian models. We recommend that you read this publication thoroughly. Your MINI is covered by the following warranties: – New Vehicle Limited Warranty – Limited Rust Perforation Warranty – Federal Emissions System Defect Warranty – Federal Emissions Performance Warranty – California Emission Control System Limited Warranty Detailed information about these warranties is listed in the Service and Warranty Information Booklet for US models or in the Warranty and Service Guide Booklet for Canadian models. We wish you an enjoyable driving experience. Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CONTENTS Using this Owner's Manual At a glance Controls and features Notes on the Owner's Manual 6 Cockpit 12 Opening and closing: Symbols used 6 Display elements 13 Keys 22 Symbol for vehicle parts 6 Display elements with navigation Central locking system 23 Your individual vehicle 6 system 14 Opening and closing – from outside 23 Editorial notice 7 Indicator and warning lamps 15 Opening and closing – from inside 26 For your own safety 8 Multifunction steering wheel MFL 18 Tailgate 27 Reporting safety defects 9 Electric power windows 28 Sliding/tilt sunroof 29 Roller sun blind 30 Adjustments: Correct sitting posture 31 Seats 31 Entry to the rear 33 Seat heating 34 Head restraints 34 Safety belts 35 Steering wheel 35 Mirrors 36 Airbags 37 Transporting children safely 38 Vehicle Memory 41 © 2002 Bayerische Motoren Werke Aktiengesellschaft Munich, Germany Reprinting, including excerpts, only with the written consent of BMW AG, Munich. Order No. 01 41 0 156 724 US English II/02 Printed in Germany Printed on environmentally friendly paper (bleached without chlorine, suitable for recycling). 2
    • OVERVIEW Driving: Technology for safety and driving Care and maintenance Ignition lock 42 convenience: Starting the engine 42 Automatic Stability Control plus Traction Special operating instructions: Switching off the engine 43 (ASC+T) 60 Break-in procedures 76 Parking brake 44 Dynamic Stability Control (DSC) 61 General driving notes 76 CONTROLS Manual transmission 45 Flat Tire Monitor 62 Refueling 77 Continuously Variable automatic Park Distance Control (PDC) 63 Fuel specifications 78 Transmission (CVT) 46 Antilock Brake System (ABS) 78 Controlling the climate for pleasant Parking lamps/Low beams 49 Brake system 79 driving: Indicator/Headlamp flasher 49 Air conditioner system 64 Wheels and tires: OPERATION Instrument lighting 50 Automatic climate control 67 Tire inflation pressure 80 Fog lamps 50 Tire condition 82 Interior lamps 50 Interior conveniences: Tire replacement 83 Light-emitting diodes 51 Glove compartment 70 Wheel and tire combinations 84 Washer/Wiper system 51 Ashtray/Beverage holder 70 Winter tires 85 Cruise control 53 Cigarette lighter 70 Snow chains 85 Everything under control: Loading and transporting cargo: REPAIRS Odometer 55 Luggage compartment cover 71 Tachometer 55 Foldable rear backrest 71 Fuel gauge 55 Loading cargo 72 Coolant temperature gauge 56 Roof-mounted luggage rack 73 Service Interval Display 57 Clock 57 DATA Computer 58 INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 3
    • CONTENTS In the engine compartment: Owner Service Procedures Technical data Hood 86 Engine compartment – Replacement procedures: Engine data 120 MINI COOPER 87 Onboard tool kit 100 Dimensions 121 Engine compartment – Windshield wiper blades 100 Weights 122 MINI COOPER S 88 Lamps and bulbs 101 Capacities 123 Washer fluid 89 Repairing a flat tire 106 Electrical system 124 Engine oil 89 Changing tires – MINI Coolant 91 with space-saver spare tire 106 Brake fluid 92 Flat tire – safety tires 110 Battery 111 Maintenance and care: Fuses 112 MINI Maintenance System 93 Caring for your vehicle 94 Giving and receiving assistance: Vehicle immobilization 96 Warning triangle 113 First-aid kit 113 Laws and regulations: Jump-starting 113 OBD interface socket 96 Tow-starting and towing 115 Technical modifications 96 California Proposition 65 Warning 97 4 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW Index Everything from A to Z 128 CONTROLS OPERATION REPAIRS DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 5
    • Notes on the Owner's Manual Symbols used Your individual vehicle In compiling this Owner's Manual we have Indicates precautions that must The manufacturer of your MINI is the made every effort to furnish you with a be followed precisely in order to Bayerische Motoren Werke Aktiengesell- convenient reference source affording avoid the possibility of personal injury schaft (BMW AG). quick access to all the essentials. The and serious damage to the vehicle. On purchasing your MINI, you have decided fastest way to find detailed information on in favor of a model with individualized any specific subject is to turn to the Contains information that will equipment and features. This Owner's comprehensive index at the back of the assist you in gaining the optimum Manual describes the entire array of manual. If you wish to gain an initial over- benefit from your vehicle and enable you options and equipment available with a view of your vehicle, you will find this in the to care more effectively for your vehicle. specific manufacturer model range. first chapter. Should you wish to sell your MINI at some Refers to measures that can be taken We hope you will understand that equip- time in the future, please remember to to help protect the environment. ment and features are included that you hand over this Owner's Manual to the new might not have chosen for your vehicle. To owner; it is an important part of the < Marks the end of a specific item of assist you in identifying possible variations vehicle. information. between your own vehicle and the If you have any additional questions, your manual's contents, the passages describing * Indicates special equipment, country- optional accessories and special equipment MINI center will be glad to advise you. specific equipment and optional extras. are marked with an asterisk *. Identifies systems or components, If your MINI features equipment that is not which your MINI center can either described in this Owner's Manual (a car activate or adapt to suit an individual radio, for instance), we have enclosed addi- driver's requirements ("Vehicle Memory"), tional Owner's Manuals. We ask you to see page 41. read these manuals as well. Symbol for vehicle parts Indicates that you should consult the relevant section of this Owner's Manual for information on a particular part or assembly. Notes Symbols 6 Online Edition for Part No. 01 41Your 724 - © 01/02 BMW AG 0 156 individual vehicle
    • OVERVIEW Editorial notice The manufacturer pursues a policy of continuous, ongoing development that is conceived to ensure that the MINI continues to embody the highest quality CONTROLS and safety standards combined with advanced, state-of-the-art technology. For this reason, it is possible that the features described in this Owner's Manual could differ from those on your vehicle. Nor can OPERATION errors and omissions be entirely ruled out. You are therefore asked to appreciate that no legal claims can be entertained on the basis of the data, illustrations or descrip- tions in this Owner's Manual. REPAIRS DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 7
    • For your own safety Important safety information. sional advice on using these items, are Use unleaded gasoline only. Fuels available from all MINI centers. containing up to and including For your own safety, use genuine parts and Installation and operation of non-MINI 10% ethanol or other oxygenates with up accessories approved by the manufacturer approved accessories such as alarms, to 2.8% oxygen by weight (i.e. 15% MTBE or of the MINI. radios, amplifiers, radar detectors, wheels, 3% methanol plus an equivalent amount When you purchase accessories tested suspension components, brake dust of co-solvent) will not void the applicable and approved by the manufacturer of the shields, telephones (including operation warranties with respect to defects in mate- MINI and Original MINI Parts, you simulta- of any portable cellular phone from within rials or workmanship. Field experience has neously acquire the assurance that they the vehicle without using an externally indicated significant differences in fuel have been thoroughly tested by the manu- mounted antenna) or transceiver equip- quality (volatility, composition, additives, facturer of the MINI to ensure optimum ment (e.g. CB, walkie-talkie, ham radio or others) among gasolines offered for sale in performance when installed on your similar) may cause extensive damage to the United States and Canada. The use of vehicle. the vehicle, compromise its safety, inter- poor-quality fuels may result in driveability, The manufacturer of the MINI warrants fere with the vehicle’s electrical system starting and stalling problems especially these parts to be free from defects in mate- or affect the validity of the MINI Limited under certain environmental conditions, rial and workmanship. Warranty. See your MINI center for addi- such as high ambient temperature and tional information.< The manufacturer of the MINI will not high altitude. accept any liability for damages resulting Should you encounter driveability prob- Maintenance, replacement, or repair from installation of parts and accessories lems which you suspect could be related to of the emission control devices and not approved by the manufacturer of the the fuel you are using, we recommend that systems may be performed by any automo- MINI. you respond by switching to a recognized tive repair establishment or individual high-quality brand. The manufacturer of the MINI cannot test using any certified automotive part.< Failure to comply with these recommenda- every product from other manufacturers to tions may result in unscheduled mainte- verify if it can be used on a MINI safely and nance. without risk to either the vehicle, its opera- Obey pertinent safety rules when you are tion, or its occupants. handling gasoline.< Original MINI Parts, MINI Accessories and other products approved by the manufac- turer of the MINI, together with profes- 8 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW CONTROLS The following only applies to vehicles owned and operated in the US. REPORTING SAFETY DEFECTS If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately OPERATION inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying BMW of North America, LLC., P.O. Box 1227, Westwood, New Jersey 07675-1227, Telephone (201) 307-4000. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or BMW of North America, LLC. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in Washington, D.C. REPAIRS area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline. DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 9
    • 10 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW OVERVIEW CONTROLS CONTROLS OPERATION OPERATION, CARE, MAINTENANCE REPAIRS OWNER SERVICE PROCEDURES DATA TECHNICAL DATA INDEX INDEX Overview 11 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • COCKPIT 1 > Parking lamps/Low beams 49 2 Washer/Wiper system 51 6 Hood release 86 > Turn signal indicators 49 3 Instrument lighting 50 7 Horn 18 > Standing lamps 49 4 Outside mirror adjustment 36 8 Steering wheel adjustment 35 > High beams 49 5 Hazard warning flashers 9 OBD interface socket 96 > Headlamp flasher 49 > Computer 58 12 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • DISPLAY ELEMENTS OVERVIEW CONTROLS OPERATION REPAIRS 1 Tachometer 55 4 Indicator for 5 Trip odometer, reset to zero 55 with indicator and warning lamps, see > Odometer 55 6 Fuel gauge 55 DATA from page 15 > Trip odometer 55 7 Engine coolant temperature gauge 56 2 Display for computer 58 > Service Interval 57 > Program display for Continuously 3 Speedometer with indicator and warning Variable Transmission (CVT) 48 lamps, see from page 15 INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 13
    • DISPLAY ELEMENTS WITH NAVIGATION SYSTEM * 1 Tachometer 55 3 Speedometer with indicator and warning 5 Indicator for with indicator and warning lamps, see lamps, see from page 15 > Odometer 55 from page 15 4 Trip odometer, reset to zero 55 > Trip odometer 55 2 Display for computer 58 > Service Interval 57 > Program display for Continuously Variable Transmission (CVT) 48 14 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • INDICATOR AND WARNING LAMPS OVERVIEW Technology Red: stop immediately Brake warning lamp q that monitors itself Battery charge current q If the lamp comes on when the The system runs a check on the warning The battery is no longer being parking brake is not engaged: and indicator lamps marked by "q" each charged. Indicates a defective alter- Check the brake fluid level. Before driving time you switch on the ignition. They each nator drive belt or a problem with the further, be sure to comply with the infor- CONTROLS light up once for different periods of time. charge circuit. Please contact the nearest mation on pages 79, 57 and 92. If a malfunction should occur in one of MINI center. Brake warning lamp for Canadian these systems, the corresponding lamp If this lamp lights up, the power-assist for models. does not go out after the engine is started steering can be deactivated. or it lights up while the vehicle is moving. OPERATION You will see how to react correctly to this If the drive belt is defective, do not With navigation system option: below. continue driving. The engine could be Coolant temperature warning damaged due to overheating. When the lamp in the speedometer q power-assist is deactivated, increased If the lamp comes on while oper- steering effort is required.< ating the vehicle, the engine has over- heated. Switch off the engine immediately Engine oil pressure q and allow to cool down, see also page 56. REPAIRS Stop immediately. Switch off engine. Check the engine oil and top up as required. Please contact the nearest MINI center. Do not continue driving, otherwise, the engine could be damaged DATA because of inadequate lubrication.< INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 15
    • INDICATOR AND WARNING LAMPS Yellow: stop immediately Red and yellow: continue to drive; Red: an important reminder Flat Tire Monitor q drive cautiously Brake warning lamp Flashes: tire failure. Brake warning lamp together with with parking brake applied. Reduce speed immediately and yellow indicator lamps for ABS, EBV More information on the parking stop the vehicle. and ASC+T/DSC: brake on page 44 The control system ABS, EBV and Parking brake lamp for Canadian With safety (run-flat) tires: ASC+T/DSC has failed. Drive models. Reduce vehicle speed carefully to under cautiously and defensively. Avoid 50 mph (80 km/h). full brake applications. Please have In both cases, avoid hard brake applications Fasten safety belts q the system checked by your MINI and steering maneuvers. Check the tire Depending on model, with acoustic center as soon as possible. inflation pressures. signal*. Lights up either for several More information on pages 60, 61 Conduct in the event of a flat tire, see seconds or until the belt is engaged, de- Brake warning lamp together with pending on version. pages 106, 110. the yellow indicator warning lamps More information on page 35 General information on the system, see ABS, EBV and ASC+T/DSC for Cana- page 62 Depending on the level of equipment, dian models. the indicator lamp is in the vicinity of the navigation system.< Airbags q Please have the system inspected at your MINI center. More information on pages 31, 37 Depending on the level of equipment, the indicator lamp is in the vicinity of the navigation system.< Hood/tailgate Lights up when the hood and/or tailgate are open. More information on pages 27, 86 16 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • INDICATOR AND WARNING LAMPS OVERVIEW Yellow: check as soon as possible Service Engine Soon q Green: for your information Flat Tire Monitor q If the warning lamp comes on Turn signal indicators Stays lit: the system is defective. either continuously or intermit- Flashes when turn signal indicator Please have the system inspected tently, this indicates a malfunction in the is on, also for trailer towing. at your MINI center. emissions-related electronic systems. Rapid flashing: the system is defective. CONTROLS More information on page 62 Although the vehicle remains operational, More information on page 49 you should have the systems checked by Antilock Brake System (ABS) q Cruise control* your MINI center at the earliest possible ABS has been deactivated in Lights up when the cruise control is opportunity. response to system malfunction. activated. Operation via the multi- Conventional braking efficiency is avail- "Service Engine Soon" warning function steering wheel. OPERATION able. Please have the system inspected lamp for Canadian models. More information on page 53 at your MINI center. More information on page 78 Engine electronics* q Blue: for your information ABS indicator lamp for Canadian Malfunction in the engine elec- High beams models. tronics. You can continue to drive Comes on when the high beams with reduced engine output or engine are on or the headlamp flasher is speed. Please have the system inspected at actuated. REPAIRS Automatic Stability Control plus your MINI center. More information on page 49 Traction (ASC+T)/Dynamic Stability Control (DSC) q Indicator lamp flashes: System active: drive and braking forces are regulated. The indicator lamp stays lit: DATA ASC+T/DSC switched off with button or defective. In the event of a defect: please have the system inspected at your MINI center. More information on pages 60, 61 INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 17
    • MULTIFUNCTION STEERING WHEEL MFL * The control buttons integrated within the Buttons facing the driver Buttons facing away from the driver MFL multifunction steering wheel have 1 Cruise control: activate/interrupt/ Left: been designed to allow you to operate a deactivate 1 > Radio number of accessories both quickly and 2 Continue cruise control Press briefly: scans for stations in FM safely, without taking your eyes from the 3 Horn band road: 4 Cruise control: store and accelerate (+) Extended pressure: station tuning > Some audio source functions 5 Cruise control: store and decelerate (–) > CD > Cruise control. Press briefly: jump to next track The illustration shows the possible full Extended pressure: fast forward in track equipment level. For further details, please > Cassette consult the description of the relevant item Press briefly: stop track scan or fast of equipment. forward Extended pressure: fast forward/ rewind Right: 1 Volume 2 Switch between radio, cassette and CD 18 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW CONTROLS OPERATION REPAIRS DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 19
    • 20 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW OVERVIEW CONTROLS CONTROLS OPERATION OPERATION, CARE, MAINTENANCE REPAIRS OWNER SERVICE PROCEDURES DATA TECHNICAL DATA INDEX INDEX Controls 21 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • KEYS Initializing the master key with remote control When you activate a master key with remote control (replacement, additional key or after a battery change), it must be initialized. This initialization can be performed in two ways: Press button 1 or button 2, see page 24, four times in succession or Depending on the equipment fitted, your Changing battery if the vehicle is unlocked: MINI has up to three key variations: Replace if it is no longer possible to unlock 1. Switch the ignition on briefly (position 2) 1 Master key with remote control and the vehicle via the remote control. and then off battery 2. Within 10 seconds, press button 1 and Only use a battery of the type speci- button 2, see page 24, in succession. If the battery is discharged, please fied on the battery (CR 2032) and consult your MINI center. Battery make absolutely sure that it is fitted in the In the event of a system malfunction, changing, see next column.< correct position.< please contact your MINI center. You can also obtain replacement keys and 2 Door and ignition key 1. Apply a screwdriver at the recess batteries there.< This key can only be used to open the 2. Use the screwdriver to lever out the doors mechanically cover. 3 Spare key for storage in a safe place, such as in your wallet. This key is not intended Return used batteries to a recycling for constant use point or your MINI center.< 22 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CENTRAL LOCKING SYSTEM OPENING AND CLOSING – FROM OUTSIDE OVERVIEW The concept Via remote control For US owners only The central locking system is ready for The remote control gives you an exception- The transmitter and receiver units comply operation whenever the driver's door is ally convenient method for unlocking and with part 15 of the FCC (Federal Communi- closed. The doors, the tailgate and the fuel locking your vehicle. It also offers another cation Commission) regulations. Operation filler door are unlocked or locked. function: is governed by the following: CONTROLS The central locking system can be oper- To open the tailgate, refer to page 24. FCC ID: LX8765S ated: The tailgate will open slightly, regardless of LX8765E > From outside via the remote control as whether it was locked or unlocked. LX8CAS well as via the door lock Whenever you unlock (lock) the vehicle, Compliance statement: > From inside by pressing a button. you simultaneously deactivate (activate) OPERATION This device complies with part 15 of the If operated from outside, the anti-theft the anti-theft system, and switch the inte- FCC Rules. Operation is subject to the system is activated at the same time. This rior lamps on (off). following two conditions: prevents the doors from being unlocked via If the vehicle has been properly locked > This device may not cause harmful inter- safety lock buttons or door handles. using the remote control, the hazard ference, and In the event of an accident, the central warning system lights up once. > this device must accept any interference locking system unlocks automatically. The When the vehicle is unlocked, the hazard received, including interference that may REPAIRS hazard warning system and interior lamps warning system does not react. cause undesired operation. are also switched on. Children might be able to lock the Any unauthorized modifications or doors from the inside. Always take changes to these devices could void the vehicle keys with you so that the the user's authority to operate this equip- vehicle can be opened again from the ment.< outside at any time.< DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 23
    • OPENING AND CLOSING – FROM OUTSIDE To unlock To lock and secure 1. Press button 1 once to unlock the Press button 2. driver's door only The hazard warning system flashes once. 2. Press button 1 a second time to unlock the other door as well as the tailgate and Do not lock the vehicle if there are the fuel filler door. passengers still inside, because they When the vehicle is unlocked, the hazard cannot unlock the doors.< warning system does not react. Non-MINI systems To open the tailgate External systems or devices may cause local Hold button 1 pressed for approx. five interference in the functions of the remote 1 Unlocking and opening the tailgate seconds. control. 2 Locking and securing The tailgate will open slightly, regardless In this case, use the master key to unlock of whether it was previously locked or the door lock. If the remote control does not react,unlocked. the battery is discharged. In the event of a system malfunction, Before and after a trip, be sure that please contact your MINI center. You can the tailgate was not opened uninten- also obtain replacement keys and batteries tionally.< from your MINI center. Battery changing, see page 22.< 24 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OPENING AND CLOSING – FROM OUTSIDE OVERVIEW Manual operation Convenience feature via door lock (in the event of electrical malfunction) You can also operate the power windows Turn the key to the extreme left or right to and the sliding/tilt sunroof via the door unlock/lock the door. lock. CONTROLS > To open: with the door closed, turn the key to the "Unlock" position and hold it > To close: with the door closed, turn the key to the "Lock" position and hold it. Watch during the closing process to OPERATION be sure that no one is injured. Via the door lock Releasing the key stops the operation.< 1. One turn of the key in the driver's door lock unlocks the driver’s door only 2. Turning the key a second time unlocks the other door, the tailgate and the fuel REPAIRS filler door. If the vehicle has been properly locked, the hazard warning system flashes once. When the vehicle is unlocked, the hazard warning system does not react. Do not lock the vehicle if there are DATA passengers still inside, because they cannot unlock the doors.< INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 25
    • OPENING AND CLOSING – FROM INSIDE The central locking system can be To lock locked automatically as soon as you Touch the switch for the central locking begin to drive if you desire. This can be system adjusted to be vehicle-specific.< or To unlock and open the doors press the individual safety lock buttons down. 1. Touch the switch for the central locking system Children might be able to lock the 2. Pull the door handle above the armrest doors from the inside. Always take or the vehicle's keys with you so that you can pull the door handle for each door twice: to open the vehicle again from the outside at With this switch, you operate the central unlock first and then open. any time.< locking system when the doors are closed. The doors and tailgate are unlocked or Convenience opening mode locked only. From ignition key position 1: The anti-theft system is not activated. Also, Hold the switch in the "Unlock" position. the fuel filler door remains unlocked to The windows and sliding/tilt sunroof open. allow refueling. Convenience closing is not possible If the remote control has been used by means of the central locking to unlock only the driver's door, see system. You should therefore close all the page 24, and you touch the switch when windows and the sliding/tilt sunroof indi- the driver's door is open, the other door, vidually.< the tailgate, and the fuel filler door are unlocked. If the driver's door is closed, touching the switch locks it.< 26 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • TAILGATE OVERVIEW CONTROLS OPERATION Opening from outside Manual operation Closing Press the button in the handle. In the event of an electrical malfunction, The handle recesses in the interior trim The tailgate opens slightly. you can also operate the tailgate manually. panel of the tailgate make it easier to pull 3. Fold the rear seat bench upwards the lid down. Opening with the remote control, see page 24. 4. Pull the ring. REPAIRS The tailgate is unlocked. To avoid injuries, be sure that the travel path of the tailgate is clear when it is closed, as with all closing proce- dures. Operate the vehicle only when the tailgate is closed. Otherwise, exhaust fumes could penetrate the interior of the vehicle. DATA Should it be absolutely necessary to operate the vehicle with the tailgate open: 1. Close all windows. Shut the sliding/tilt sunroof 2. Sharply increase the air supply for the air conditioning or automatic climate INDEX control, see pages 64 and/or 67.< Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 27
    • ELECTRIC POWER WINDOWS To close: After the ignition has been switched off: Press the switch upwards. You can use the electric power windows as The window closes until you release the long as no one opens any of the doors. switch If a door is opened during operation, the or opening/closing process stops immedi- ately. when the engine is running: Briefly press the switch upwards. When leaving the vehicle, always The window closes automatically. remove the ignition key from the Pressing the switch again stops the opera- lock and remember to close the doors to tion. prevent children from operating the power windows and injuring themselves, etc.< Open and close windows The window on the front passenger From ignition key position 1: side cannot be closed automati- For the convenience mode via the door To open: cally.< lock, refer to page 25. Press the switch downwards. Watch during the closing process to The window opens until you release the be sure that no one is injured.< switch or briefly press the switch downwards. The window opens automatically. Pressing the switch again stops the opera- tion. 28 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • SLIDING/TILT SUNROOF * OVERVIEW To prevent injuries, exercise care Do not use force to close the sliding/ when closing the sliding/tilt sunroof tilt sunroof in its raised position, as and keep it in your field of vision until it is damage to the mechanism could result.< shut. When leaving the vehicle, always remove After the ignition has been switched off: CONTROLS the ignition key from the lock and You can still operate the sliding/tilt sunroof remember to close the doors to prevent for up to one minute, as long as no one children from operating the sunroof and opens any of the doors. injuring themselves, etc. If a door is opened during operation, the Be sure that adequate clearance is main- opening/closing stops immediately. OPERATION tained for the opening path of the sliding/ tilt sunroof, otherwise damage can occur.< Automatic opening and closing Raising – Opening – Closing To open: For the convenience mode via the door From ignition key position 1: lock, refer to page 25. Push the switch past the resistance point: To raise: The sunroof opens completely Press the switch To close: REPAIRS or 1. Push the switch past the resistance push the switch backwards to the resis- point: tance point. The sunroof closes to the raised position 2. Push the switch again: Opening and closing The sunroof closes completely. 1. Push the switch in the desired direction Touching the switch briefly during opening DATA until you feel resistance and hold in this or closing stops the movement immedi- position ately. 2. Release the switch when the desired position has been reached. INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 29
    • SLIDING/TILT SUNROOF * ROLLER SUN BLIND* Safety feature As of approximately the middle of the roof opening, if the sliding/tilt sunroof encoun- ters resistance during closing, the closing operation is interrupted and the sunroof opens again slightly. Despite this safety feature, be extremely careful that the closing path of the sunroof is not obstructed when- ever it is closed. Otherwise, triggering the closing-force limitation may not be ensured in some situations (with very thin Manual opening and closing 1 Opening objects, for instance). In the event of an electrical malfunction, 1. Press the button in the handle, see You can override this safety feature by you can also operate the sliding/tilt arrow 1. pressing the switch beyond the resistance sunroof manually: The cap is unlocked point and holding it.< 1. Push the clock towards the interior and 2. Guide the roller sun blind towards the remove back. 2 Use an Allen wrench to turn the sliding/ tilt sunroof in the desired direction. 2 Closing 1. Use the handle to pull the roller sun blind forwards 2. Engage the handle in the device, see arrow 2. 30 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CORRECT SITTING POSTURE SEAT ADJUSTMENT OVERVIEW The ideal seating position can make a vital Safe with safety belts Important adjustment information contribution to relaxed, fatigue-free Never allow more than one person to Never try to adjust your seat while driving. The correct seating position also wear a single safety belt. Never allow operating the vehicle. The seat could works together with the safety belts and infants or small children to ride in a respond with an unexpected movement, airbags to provide occupants with passenger's lap. Avoid twisting the belt and the ensuing loss of vehicle control CONTROLS maximum levels of passive safety in an while routing it firmly across the hips and could lead to an accident. accident. To ensure that the safety systems shoulder, wear it as snugly against your Never ride with the backrest reclined to an operate with optimal efficiency, we body as possible. Do not allow the belt to extreme horizontal angle (especially impor- strongly urge you to observe the instruc- rest against hard or fragile objects. Do not tant for front passengers to remember). tions contained in the following section. route the belt across your neck, or run it Keep the backrest relatively upright to OPERATION For supplementary information on trans- across sharp edges. Be sure that the belt minimize the risk of sliding under the porting children, refer to page 38. does not become caught or jammed. safety belt and sustaining injury in an acci- Avoid wearing bulky clothing that prevents dent.< Sitting correctly with airbags the belt from fitting properly, and pull on Always maintain an adequate the belt periodically to retension it over Adjusting the seats, see next page. distance between yourself and all of your shoulders. In the event of a frontal the airbags. Always hold the steering wheel impact, a loose lap belt could slide over the REPAIRS by the rim with the hands at the 9 and hips, leading to abdominal injury. In addi- 3 o'clock positions to keep any chance of tion, the safety belt's restraint effective- injury to hands or arms to an absolute ness is reduced if the belt is worn loosely. minimum, should the airbag be deployed. Expectant mothers should always wear No one and nothing is to come between the their safety belts, taking care to position airbags and the seat occupant. the lap belt against the lower hips, where it will not exert pressure against the abdom- DATA Never use the front passenger airbag cover as a storage surface for objects of any kind, inal area.< or as a support for legs or feet, as this will increase the risk of injury in a collision severe For information on using the safety belts, enough in which the airbag will deploy.< refer to page 35. INDEX For airbag locations and additional infor- mation on airbags, refer to page 37. Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 31
    • SEAT ADJUSTMENT Longitudinal seat adjustment Seat height Lumbar support* 1. Lift the handle 1. To raise: You can adjust the contour of the backrest 2. Push the seat into the desired position Pull the handle up repeatedly, for additional support in the curvature of 3. After releasing the handle, apply pres- continuing until the seat reaches the your spine's lumbar region. sure to the seat to ensure that the latch desired height The upper hips and spinal column receive engages securely. 2. To lower: supplementary support to help you main- Push the handle repeatedly, continuing tain a relaxed, upright posture. Make corrections in the longitudinal until the seat reaches the desired height. Turn the wheel to increase or decrease the adjustment of the seat to ensure that curvature. the safety belt still fits firmly against your body. If you do not do this, the protection provided by the safety belt may be reduced.< 32 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • SEAT ADJUSTMENT ENTRY TO THE REAR OVERVIEW When returning the seat to the rear position, ensure that no one is injured and that no objects are damaged. Engage and lock both seats and backrests into position prior to driving, otherwise CONTROLS unexpected movement could increase the risk of accident.< OPERATION Backrest tilt Easy Entry 1. Pull the lever at the inside of the seat 1. Press the lever on the outside of the seat 2. Apply weight to or remove weight from downwards, see arrow 1. the backrest as required The backrest folds forward automati- 3. Release the lever so that the backrest cally REPAIRS locks into place. 2. Push the seat forwards, see arrow 2. Original position 1. Push the seat back into its home posi- tion 2. Fold the backrest back to the home posi- tion to lock the seat. DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 33
    • HEATED SEATS* HEAD RESTRAINTS Installation 1. Press the button and at the same time insert the head restraint in the reception points 2. Adjust the head restraint. To avoid possible violation of traffic laws, never retract the head restraints unless the rear seats are empty. Always ensure that the head restraints are raised before transporting passengers in the rear seat.< The seat cushion and backrest can be Adjusting the head restraints heated with the ignition key in position 2. To raise: pull the head restraint upward. To lower: press the button and push the Select the temperature setting: head restraint downward. Press each button briefly. You can reduce the risk of spinal Direct deactivation from second tempera- injury and whiplash by adjusting the ture setting. head restraint to a height at which it is Press the button for a longer period. centered roughly at ear level.< Removal 1. Pull up the head restraint, continuing until it is at maximum extension 2. Press the button and remove the head restraint at the same time. 34 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • SAFETY BELTS STEERING WHEEL OVERVIEW CONTROLS OPERATION Drive with your safety belt on Safety belt height adjustment To adjust the steering wheel height Even though there is an airbag, wear a Use the height adjustment mechanism to 1. Push the locking lever downward safety belt every time you get in the adapt the safety belt to the ideal position 2. Adjust the desired steering wheel vehicle, because airbags enhance safety by for your own body: position providing added protection. Press the button and at the same time push 3. Pull the lever back in. REPAIRS the entire unit upwards or downwards. To fasten Do not adjust the steering wheel Also observe the instructions on adjusting Make sure you hear the lock engage in the while the vehicle is moving, other- the seats on page 31. belt buckle. wise unexpected movement could increase the risk of accident.< If the safety belts are damaged or To release stretched in an accident: have the 1. Press the red button in the belt buckle safety belt system replaced by your MINI DATA 2. Hold the belt center and the belt anchors checked, other- 3. Guide the belt back into its reel. wise the safety function can no longer be guaranteed. If a child-restraint system was in the vehicle during an accident, consult the manufacturer's instructions regarding INDEX replacement.< Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 35
    • MIRRORS Manual adjustment The mirrors can also be adjusted manually: Press the edge of the lens. Electric heating* Both mirrors are heated automatically when the ignition key is in position 2. Adjusting exterior mirrors Interior rearview mirror 1 Switch for choosing between the left and To reduce glare from vehicles behind you right mirror when you are driving at night: 2 Switch for 4-way adjustment. Tilt the lever forward. Illuminated vanity mirror From ignition key position 1: 1. Fold down the sun visor 2. Fold the cover panel upwards. Sun visors Can be swung sideways. 36 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • MIRRORS AIRBAGS OVERVIEW designed to help support the seat occu- pant's upper body. For information on sitting posture, refer to page 31. CONTROLS The airbags do not deploy in response to minor collisions, rear impacts and certain kinds of vehicle rollover.< Even when all safety guidelines are OPERATION observed, there is a small residual risk that passengers will sustain facial, hand or arm Interior rearview mirror, automatic 1 Side airbags in seats on the driver and injuries in isolated instances. The ignition dimming feature* passenger sides (front) and inflation noise may induce a mild The mirror dims automatically as required. 2 Head airbags on the driver and temporary hearing loss in sensitive individ- The mirror becomes clear again when you passenger sides for both rows of seats uals. engage reverse gear or select selector lever (front/rear) REPAIRS position R. 3 Front airbags on the driver and Do not apply adhesive materials to Keep the photocells free and clean to passenger sides the cover panels of the airbags, cover ensure that the mirror functions perfectly. them or modify them in any other way. Do There is one photocell in the mirror frame; Protective effect not fit covers, cushions or other items to the other is on the back of the mirror. The front airbags supplement the safety the front seats that have not been specially belts by helping to provide additional approved for seats with side airbags. Do Do not cover the area between the not hang clothing, e.g. jackets, over the DATA protection for the driver and front inside rearview mirror and the wind- passenger in the event of a frontal collision backrests. Do not attempt to remove the shield, and do not place stickers or toll tags in which the protection afforded by the airbag restraint system from the vehicle. In on the windshield in front of the mirror.< belts alone may no longer be sufficient. the event of malfunctions, immobilization When needed, the head and side airbags or use (triggering) of the airbag restraint help to furnish protection in the event of system in accordance with its intended INDEX side impact. Each of the side airbags is function, only commission a MINI center with the inspection, repair or disassembly. Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 37
    • AIRBAGS TRANSPORTING CHILDREN Do not make any changes yourself to the Indicator lamp individual components and wiring. This The indicator lamp on the instru- includes the padded cover of the steering ment panel shows the airbag wheel, in the instrument panel and the roof system status starting from igni- supports, as well as the sides of the roof- tion key position 1. liner and the original backrest covers on the System operational: front seats. Do not attempt to remove or dismantle the steering wheel. In view of > The indicator lamp comes on briefly. the applicable safety regulations, arrange for your MINI center to dispose of the System malfunction: airbag generators. Unprofessional > The indicator lamp does not come on attempts to service the system could lead > The indicator lamp fails to go out after to failure in an emergency or undesired the engine has been started, or it comes Children younger than 13 years and/or airbag activation, either of which could on during normal driving. smaller than 5 ft (150 cm) should only result in personal injury. Do not touch the travel in the rear in suitable restraint A system defect could prevent the airbags individual components directly after the systems. from deploying in response to a severe system has been triggered, as otherwise impact occurring within the system's Commercially-available child-restraint there is a danger of burns.< normal triggering range. systems are designed to be secured with a lap belt or with the lap belt portion of a At all times, occupants should sit Have the system checked as soon as combination lap/shoulder belt. Improperly upright and be properly restrained possible by your MINI center. or inadequately installed restraint systems (infants and small children in appropriate can increase the risk of injury to children. child-restraint systems; larger children and Always read and follow the instructions adults using the safety belts). Never let an that come with the system. occupant's head rest near or on a head If you use a child-restraint system with a airbag because the inflating airbag could tether strap: cause serious or fatal injury. A child which is not properly restrained could place his or her head on or near the airbag.< 38 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • TRANSPORTING CHILDREN SAFELY OVERVIEW Adjust the tether strap according to the child restraint manufacturer's instructions. Before installing any child- restraint device or child seat, please read the following: CONTROLS Never install a rearward-facing child- restraint system in the front passenger seat of this vehicle. Your vehicle is equipped with an airbag supplemental restraint system for the front OPERATION passenger. Because the backrest on any rearward-facing child-restraint system – Your vehicle has one of two different types Both seating positions are fitted with a of the kind designed for infants under of child-restraint anchor fittings on the head restraint. Lift the head restraint and 1 year and 20 Ibs./9 kg – would be within back of the rear seats, see arrows 1 or 2. pass the tether strap between the head the airbag's deployment range, you should restraint and the seat back. It is recom- never mount such a device in the front Depending on the location selected for mended to readjust the head restraint into passenger seat, since the impact of the seating in the rear passenger area, attach the lowest possible position. REPAIRS the tether strap to the corresponding airbag against the child restraint's backrest anchorage point to secure the child- could lead to serious or fatal injuries. restraint system. If it is necessary for a child – not an infant – to ride in the front seat, certain precautions Adjust the tether strap according to the should be taken. First, move the passenger child restraint manufacturer’s instructions. seat as far away from the instrument panel as possible. This important precaution is DATA Anchor fitting 1 is shown above. intended to maximize the distance Anchor fitting 2 is shown in the next between the airbag and the child. Older column.< children should be tightly secured with a safety belt, after they have outgrown a booster seat that is appropriate for their age, height and weight. Younger children INDEX should be secured in an appropriate Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 39
    • TRANSPORTING CHILDREN SAFELY forward-facing child-restraint system that To lock the belt has first been properly secured with a Pull the entire length of the belt from the safety belt. Never install a rearward-facing belt retractor. Allow the reel to retract the child-restraint system in the front belt somewhat and engage the buckle, passenger seat. then tighten the belt against the child- We strongly urge you to carefully read and restraint system. The retraction mecha- comply with the instructions for installa- nism is now locked. tion and use provided by the child restraint's manufacturer whenever you use To unlock the belt such a device. Release the buckle, remove the child- Be sure that all occupants – of all ages – restraint system and allow the belt remain properly and securely restrained at Child seat security retractor to reel the belt completely in. all times. According to accident statistics, children All of the rear belt retractors and the front are safer when properly restrained in the passenger's safety belt can be locked for rear seats than in the front seating posi- mounting and securing child-restraint tions.< systems. Information regarding this is located near All rear seats in your vehicle conform to the the buckle latch of each safety belt. guidelines defined in SAE J1819, an industry recommended practice for securing child-restraint systems in motor vehicles. 40 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • TRANSPORTING CHILDREN VEHICLE MEMORY OVERVIEW How the system functions > Automatic activation of windshield Doubtless you have often reflected on how wipers on cleaning great it would be if you could configure > "Follow me home" lamps your vehicle's various adjustment settings Low beams light up for a short time after to meet your own personal requirements. the engine has been switched off CONTROLS In developing this vehicle, the manufac- > Locking when engine is running (with turer has incorporated a number of options second key) that your MINI center can program to > Stop function of power windows on reflect your individual preferences. opening/closing > Activating/deactivating daytime driving lamps* OPERATION What the system can do > Switching on interior lamps via remote LATCH child-restraint system Your MINI center can provide you with control. details on the capabilities of the Vehicle Open the cover. Memory system. The illustration is an example showing This symbol draws your attention to Examples for Vehicle Memory: other Vehicle Memory functions the mounts for the LATCH (Lower Anchors and Tethers for Children) child-restraint > Signals an acknowledgement when described in the Owner's Manual.< REPAIRS mounting system at the right rear. locking or unlocking your vehicle The system is also available at the left rear > Automatic locking after starting off position. > Automatic unlocking when the parking brake is applied Always follow all manufacturer's > Selective central locking instructions and observe all safety First open the driver's door, then the precautions when installing the LATCH whole car DATA child-restraint system.< > Automatic opening/closing of sliding/tilt sunroof > Opening/closing windows and/or sliding/tilt sunroof via remote control > Speed-dependent windshield wiper INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 41
    • IGNITION LOCK STARTING THE ENGINE Vehicles with Continuously Variable Do not allow the engine to warm up with automatic Transmission (CVT): the vehicle at a standstill. Move off imme- Do not move the selector lever from posi- diately at a moderate engine speed. tion "P" until the engine is running. Your vehicle is equipped with an interlock. Do not allow the engine to run in Therefore, the ignition key cannot be enclosed spaces. The exhaust gases turned to position 0 and removed until the contain carbon monoxide, an odorless and selector lever is in position "P" (Interlock).<colorless, but highly toxic gas. Breathing the exhaust gases poses an 1 Steering unlocked extreme health risk, and can lead to uncon- Individual electrical accessories are ready sciousness and death. for operation. Do not leave the vehicle unattended with 0 Steering locked the engine running. An unattended vehicle 1 Steering unlocked You will find that it is often easier to turn with a running engine represents a poten- 2 Ignition switched on the ignition key from position 0 to posi- tial safety hazard. When driving, standing 3 Starting the engine tion 1 when you move the steering wheel at idle or when parking, take precautions to slightly to help disengage the lock. avoid contact between the hot exhaust 0 Steering locked system and easily flammable materials The key can be inserted or removed in this 2 Ignition switched on (grass, hay or leaves, for example). Such position only. All electrical accessories are ready for oper- contact could lead to a fire, resulting in ation. serious personal injury and property To lock the steering: damage.< 1. Remove the key 3 Starting the engine 2. Turn the steering wheel slightly to the Vehicles with manual transmission: left or right until the lock engages. Step on the clutch when starting the vehicle. A lockout prevents the engine from starting if the clutch is not depressed.< 42 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • STARTING THE ENGINE SWITCHING OFF THE ENGINE OVERVIEW Starting Manual transmission You should never remove the ignition When starting the engine, do not press the 1.Engage the parking brake key when the vehicle is in motion, as accelerator pedal. 2.Put the manual gearshift lever in neutral the steering lock could engage. 3.Press the clutch pedal When you leave the vehicle, always remove Do not actuate the starter for too 4.Start the engine. the ignition key and engage the steering CONTROLS short a time. Do not turn it for more lock. than approx. 20 seconds. Release the igni- Continuously Variable automatic When you park on downward slopes, tion key immediately when the engine Transmission (CVT)* engage the parking brake.< starts. 1. Press the footbrake Extended starting attempts, characterized Manual transmission 2. Put the selector lever in position P or N OPERATION by excessively frequent or long periods 3. Starting the engine. Turn the ignition key to position 1 or 0. with the starter engaged, can lead to damage in the catalytic converter.< Move the selector lever to position N Continuously Variable automatic and engage the parking brake before Transmission (CVT)* If the engine does not start on the first leaving your vehicle with the engine Engage selector lever position P, turn the attempt (the engine is very hot or cold, for running. ignition key to position 1 or 0. instance): Do not leave the vehicle with the engine REPAIRS > Press the accelerator pedal halfway running. An unattended vehicle with a down while engaging the starter. running engine represents a potential Cold starts at extremely low temperatures safety hazard.< (as of approx. +5 7(–15 6)): > Press the accelerator pedal halfway down while engaging the starter DATA > For the initial start attempt, allow the starter to remain engaged somewhat longer (approx. 10 seconds). INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 43
    • PARKING BRAKE If, in exceptional circumstances, it should be necessary to engage the parking brake while the vehicle is in motion, do not pull the lever with excessive pressure. Keep your thumb pressed against the release button while carefully pulling the lever up to apply moderate pressure. Excessive pressure can lead to overbraking and loss of traction (fishtailing) at the rear axle. The brake lamps do not come on when the The parking brake is designed primarily to parking brake is engaged. prevent the vehicle from rolling when it is Vehicles with manual transmission: parked. It operates against the rear wheels. Always engage the parking brake when parking on hills and inclined surfaces, as To engage first gear or reverse may not provide Lever automatically locks in position. adequate resistance to rolling. The warning lamp in the instrument cluster Vehicles with CVT: comes on when the ignition key is in posi- Place the selector lever in P.< tion 2, see page 16. To release 1. Pull up slightly 2. Press the button 3. Push the lever downwards. 44 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • MANUAL TRANSMISSION OVERVIEW Reverse Before selecting reverse gear, ensure the vehicle is stationary; then, fully press the clutch pedal and pause briefly before moving the gearshift lever into position. CONTROLS As you do this, the backup lamps will turn on automatically when the ignition key is in position 2. 5-speed transmission: Press the gearshift lever to the right and to OPERATION the back. The manual gearshift lever neutral plane 6-speed transmission: lies in the gear plane of the 3rd/4th gear. Press the gearshift lever to the left to over- When shifting from each gear into come the slight resistance and press "Neutral", the manual gearshift lever forwards. springs back automatically into the gear- As you do this, the backup lamps will turn REPAIRS shift lever neutral plane. on automatically when the ignition key is in position 2. 6-speed transmission* When changing gear in the 5th/6th Do not hold the vehicle in place on gear plane, press the gearshift lever slopes by slipping or "riding" the to the right to prevent shifting to a gear of clutch. Use the parking brake instead. Riding the clutch causes the clutch DATA the 3rd/4th gear plane.< assembly to wear out sooner.< INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 45
    • CONTINUOUSLY VARIABLE AUTOMATIC TRANSMISSION (CVT) * You can drive with a steplessly shifting CVT. While the vehicle is stationary and In addition, you can also shift manually. before shifting out of P or N, press When you move the selector lever from the the brake pedal in order to disengage the D position to the right into the M/S + – selector lever lock mechanism (Shiftlock). range, the performance-oriented shift If the engine speed is too high when the programs of the CVT are engaged. Step- vehicle is at a standstill, the selector lever tronic enters the manual selection mode is also blocked to protect the transmission. and executes the desired shift whenever Hold the brake pedal down until starting you tap the selector lever in the direction off. Otherwise the vehicle will "creep" when indicated by "+" or "–" . a drive position is engaged.< Whenever you want to use automatic To prevent the vehicle from starting again, just move the selector lever toward Selector lever positions off on its own, always move the the left to position D. P R N D M/S + – selector lever to position P or N and engage the parking brake before leaving your In positition D, you achieve the Range selection vehicle with the engine running. lowest fuel consumption for average Inadvertent engaging of certain selector Do not leave the vehicle unattended with driving.< lever positions is prevented by a lock. the engine running. An unattended vehicle with a running engine represents a poten- Press the button on the front side of the tial safety hazard.< selector lever knob. The lock is released. If the selector lever is not placed in position P when the vehicle is parked, the position display of the selector lever stays on. This can lead to battery discharge.< 46 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CONTINUOUSLY VARIABLE AUTOMATIC TRANSMISSION (CVT) * OVERVIEW P Park The transmission will only execute upshifts Select "P" only when the vehicle is and downshifts that will result in a plau- completely stopped. Transmission locks to sible combination of vehicle speed and prevent rear wheels from turning. engine rpm, forinstance, downshifts that would result in excessive engine speed are CONTROLS R Reverse not executed. Select "R" only when the vehicle is Switching from M/S + – into the selector completely stopped. lever positions P, R and N and switching from manual mode back into the Sport N Neutral program is only possible via D. OPERATION Select "N" only if your journey is inter- rupted for a long period. M/S + – Manual mode and Sport program D Drive (CVT driving position) Switch from D into M/S + –: This position is designed for driving under Activates the Sport program and indicates all normal operating conditions. SD in the gear indicator in the speedo- REPAIRS meter. "Kickdown" > Press briefly: In "kickdown", you achieve maximum CVT shifts from the Sport program to the acceleration and maximum speed in posi- manual mode tion D. > Press selector lever briefly towards "+": Press the accelerator pedal past the Transmission shifts upwards increased resistance point at the full- > Press selector lever briefly towards "–": DATA throttle position. Transmission shifts back. 1 to 6 appear in the gear indicator. INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 47
    • CONTINUOUSLY VARIABLE AUTOMATIC TRANSMISSION (CVT) * Do not work in the engine compart- ment when a drive gear (forward or reverse) is engaged. If you do this, the vehicle could move.< Jump-starting and towing, refer to pages 113, 115.< Available displays P R N D SD 1 2 3 4 5 6 EP Electronic transmission control module If there is a malfunction in the transmission system, EP appears in the display. All selector lever positions can still be selected. In positions for driving forward: The vehicle can now only be driven with a limited gear selection. Avoid high engine loads. Proceed to the nearest MINI center.< 48 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • PARKING LAMPS/LOW BEAMS SIGNAL/HEADLAMP FLASHER OVERVIEW You can also have this function acti- vated.< Switching on the standing lamps For parking, you can activate lights on one CONTROLS side of the vehicle (observe local laws). In ignition key position 0: Move the lever into the relevant turn signal indicator position. OPERATION "Lights on" warning Switching on the parking lamps If the lights have not been switched off and 1 Turn signal indicator (green indicator Turn to the first position. the ignition key is in position 0, an acoustic accompanied by periodic clicking sound The front, rear and side vehicle lighting is signal sounds for a few seconds when you from the relay) switched on. open the driver's door to remind you that 2 High beams/Headlamp flasher (blue One-sided standing lamps, see next the lights have not been switched off. indicator lamp) REPAIRS column. Daytime driving lamps* To signal briefly Switching on the low beams If you desire, the light switch can be left in Press the lever up to but not beyond the Turn to the second position. the second position: detent. With the low beams on and with the igni- When the ignition is switched off, the tion switched off, only the parking lamps external lighting is also switched off. If the indicator lamp of the indicators will remain on. and the clicking from the relay are DATA You can have this function set by both faster than normal: one of the turn "Follow me home" lamps your MINI center.< signal indicators has failed.< If you switch off the engine with the low beams on, and then switch off the low beams, they remain lit for approx. one INDEX minute. Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 49
    • INSTRUMENT LIGHTING FOG LAMPS INTERIOR LAMPS To control the instrument lighting, press When the parking lamps/low beams are Switching the interior lamps on and the button. switched on: off manually Briefly press the switch upwards or down- Press button 1. To increase the illumination intensity wards. Keep the button pressed until the desired Briefly press once again to switch off. Switching the reading lamps on and brightness is reached. off Fog lamps* Press button 2. To decrease the illumination intensity Fog lamps switched on: Press the button briefly. Green light-emitting diode in the With each brief press of the button, the switch lights up. illumination intensity is reduced in steps. The fog lamps are deactivated whenever the high beams are switched on. 50 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • LIGHT-EMITTING DIODES WASHER/WIPER SYSTEM OVERVIEW Light-emitting diodes (LEDs) installed Rain sensor* behind translucent lenses serve as the light The rain sensor is located on the wind- source for many of the controls and shield, directly in front of the interior rear- displays in your vehicle. These light-emit- view mirror. When the rain sensor is ting diodes are related to conventional activated, the windshield wipers are auto- CONTROLS lasers, and legislation defines them as matically controlled depending on the "light-emitting diodes, Class 1". amount of water (or snow) landing on the windshield. Do not remove the protective lens To activate the rain sensor: and avoid staring directly at the unfil- From ignition key position 1: OPERATION tered beam for several hours, as inflamma- tion of the iris could result.< Lever in position 1. 0 Wipers parked The wipers move across the windshield 1 Intermittent operation or rain sensor once. 2 Normal wiper speed To deactivate the rain sensor: 3 Fast wiper speed 4 Brief wipe Put lever in position 0. 5 Clean windshield and headlamps REPAIRS Switch the rain sensor off when Intermittent operation passing through an automatic car wash. Failure to do so could result in (not on vehicles with rain sensor) damage caused by undesired wiper activa- The interval varies depending on the speed tion.< being driven. DATA You can have this function set by Fast wiper speed your MINI center.< When the vehicle is stationary, the wipers switch automatically to normal wiper speed. You can have this function activated/ INDEX deactivated by your MINI center.< Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 51
    • WASHER/WIPER SYSTEM Cleaning windshield and headlamps* The system sprays washer fluid against the windshield. The wipers are automatically activated for a brief period. When the vehicle lighting is on, the head- lamps are also cleaned at appropriate inter- vals. Do not use the washers if there is any danger that the fluid will freeze on the windshield. If you do so, your vision could be obscured. For this reason, use an Rear window wiper antifreeze agent, see page 89. 6 Intermittent operation: Do not use the washers when the reservoir Turn the cap to position 6 is empty, since this could cause damage to The rear window wiper moves across the the washing pump.< window a number of times before switching to intermittent operation Windshield washer jets* The windshield washer jets are heated Cleaning the rear window automatically when the ignition key is in 7 Intermittent operation: position 2. Turn the cap to position 7 and hold in place 8 In lever position 0: Turn the cap to position 8 and hold in place 52 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CRUISE CONTROL* OVERVIEW To activate the system To decelerate From ignition key position 1: Press button 4. Press button 2. If you are already driving with active cruise The indicator lamp in the instrument control, the speed is decreased by approx. CONTROLS cluster lights up. 1 mph (2 km/h) every time you briefly tap Cruise control is active. the button. To maintain and store speed or to Press and hold button 4. accelerate With the cruise control active, the system automatically reduces the throttle opening OPERATION Press button 3. to slow the vehicle. When you release the The system maintains and stores the Starting at about 25 mph (40 km/h), the button, the system maintains and stores current vehicle speed. Every time you tap vehicle maintains and stores any vehicle the current speed. the button, the speed increases by approx. speed that you specify. 1 mph (2 km/h). Do not use cruise control on twisting Press and hold button 3. roads, when high traffic density REPAIRS prevents driving at a constant speed, when The vehicle accelerates without pressure on the road surface is slick (snow, rain, ice), or the accelerator pedal. When you release when the road surface is loose (rocks, the button, the system maintains and sand).< stores the current speed. If, on a downhill gradient, the engine DATA braking effect is not sufficient, the controlled speed may be exceeded. Speed can drop on uphill grades if the engine output is insufficient.< INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 53
    • CRUISE CONTROL* To cancel the cruise control To continue cruise control When the system is activated, press Press button 1. button 2. The vehicle accelerates to and maintains The indicator lamp stays lit. the last speed stored. If you turn the igni- You can use the cruise control again as tion key to position 0, the stored speed is required. deleted and the system is deactivated. In addition, cruise control is canceled auto- matically To deactivate the system > if the brakes are applied With cancelled cruise control, press > when you apply pressure to the clutch button 2 once again. pedal, or when you move the CVT The indicator lamp goes out and the stored selector lever from D to P, N or R speed is deleted. > or if the cruise speed is either exceeded or not met for an extended length of time (if you press the accelerator pedal and exceed the stored speed, for example). 54 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • ODOMETER TACHOMETER FUEL GAUGE OVERVIEW CONTROLS OPERATION 1 Trip odometer Do not operate the engine with the needle In the speedometer To set to zero: in the red overspeed zone of the gauge. Once indicator lamp 1 stays on continu- With ignition key in position 1, press the To protect the engine, the power is reduced ously, there are still approx. 2.1 gallons button until the trip odometer is at zero. when you approach a certain engine speed (8 liters) of fuel in the fuel tank. in this sector. Tank capacity: approx. 13.2 gallons REPAIRS 2 Odometer (50 liters). You can activate the displays shown in the When you switch on the ignition, the indi- illustration with the ignition key in posi- cator lamp lights up briefly to confirm that tion 0 by pressing the button in the instru- the system is operational. ment cluster. If the tilt of the vehicle varies (when you are driving in mountainous areas, for example), the needle may fluctuate DATA slightly. Please refuel early, since driving to the last drop of fuel can result in damage to the engine and/or catalytic INDEX converter.< Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 55
    • FUEL GAUGE TEMPERATURE GAUGE 1 Red indicator lamp When you switch on the ignition, warning lamp 1 comes on briefly to confirm that the system is operational. If the lamp comes on while operating the vehicle, the engine has overheated. Switch off the engine immediately and allow it to cool down. Navigation system option Coolant temperature warning In the navigation system Low temperature lamp in the tachometer. Please also comply with the instruc- The needle is located at the bottom or on If the lamp comes on while oper- tions in the previous column.< the right. ating the vehicle, the engine has over- heated. Switch off the engine immediately The engine is still cold. Drive at moderate Once indicator lamp 1 switches from and allow it to cool down. engine and vehicle speeds. orange to red, there are still approx. 2.1 gallons (8 liters) of fuel in the fuel tank. Center position Normal operating temperature of the engine. High temperature As soon as there is a deviation from the center position upwards or to the left: Drive moderately and at low engine speed, if necessary, switch off the engine and allow to cool down. Checking coolant level, see page 91. 56 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • SERVICE INTERVAL DISPLAY OVERVIEW A flashing message and a "–" in front of the number mean that the service interval has already been exceeded by the distance shown on the display. Please contact your MINI center for an appointment. CONTROLS For more information on the Service Interval Display, see page 93. OPERATION Remaining distance for service Brake fluid change The displays shown in the illustration You can obtain a display of the number of appear for a few seconds when the ignition days remaining until the next due brake key is in position 1 or after the engine is fluid change, see page 92. started. While the next due service is displayed, REPAIRS The next service due appears in miles (kilo- press the button in the display element. meters) with the message INSPECTION or/ As of the due date of the brake fluid and OILSERVICE, together with the distance change, the clock symbol also lights up in remaining before the next scheduled the remaining distance display for Service, service. The computer bases its calculations see left column. Please contact your MINI of the remaining distance on your driving center for an appointment. style in the period immediately preceding DATA your data request. Periods of immobilization in which the battery is disconnected are not taken into account by the display. For this reason, ensure that the brake fluid, independent of the display, is replaced INDEX every two years at the latest, see page 92.< Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 57
    • CLOCK COMPUTER* The displays appear in the following order: Outside temperature, cruising range, average fuel consumption, average vehicle speed. Starting with ignition key position 1, the last active setting is displayed. If the vehicle is equipped with a navi- gation system, see chapter covering the computer in the navigation system Owner's Manual.< Settings Mode selection From ignition key position 1: With the ignition key in position 1 and Left button: hours higher, you can use the button in the turn signal indicator lever to retrieve informa- Right button: minutes tion from the computer for display in the tachometer. By pressing the button briefly, Move forward in increments: you can call up a new function for display. Press the button or Fast forward: Press and hold the button Changeover from 24-hour to 12-hour mode: Press both buttons at the same time for approx. 5 seconds. 58 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • COMPUTER* OVERVIEW Average speed – Average fuel consumption Press the button in the turn signal indicator lever for a longer period. CONTROLS The average speed value/consumption value on display is recalculated. Any time spent when the vehicle is stationary and the engine is switched off is ignored for the calculation. OPERATION Outside temperature If the vehicle is equipped with a tacho- meter, but not with a computer, the temperature is always displayed. REPAIRS You can display the exterior tempera- ture and distance driven in other units of measurement.< Cruising range The computer bases its calculations for the cruising range on the driving style and on DATA the remaining fuel in the tank. INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 59
    • AUTOMATIC STABILITY CONTROL PLUS TRACTION (ASC+T) * The concept Indicator lamp This system optimizes vehicle stability and The indicator lamp on the instru- traction, especially when just starting off, ment cluster will go out shortly when accelerating or when cornering. after the ignition has been ASC+T recognizes the danger present in switched on, see pages 16, 17. traction loss and will increase driving If the indicator lamp flashes: stability and traction by reducing the ASC+T controls the drive and braking engine's output, and if necessary, by forces. applying the brakes to the front wheels. ASC+T is operational each time you start If the indicator lamp fails to go out the engine. after the engine is started, or if it Switch off the ASC+T comes on during normal driving and stays The laws of physics cannot be on: repealed, even with ASC+T. An appro- Briefly press the switch. If the system is either defective or was priate driving style always remains the The indicator lamp stays lit. switched off with the button, then the responsibility of the driver. Avoid using the When driving with snow chains or to "rock stabilizing applications described are no additional safety margin provided by the free" in snow, it can be helpful to switch off longer available. You can, however, drive system as an excuse for taking unnecessary the ASC+T for a brief period. the vehicle normally without ASC+T. risks. In the event of a malfunction, please see Do not make any modifications to the To maintain vehicle stability, always your MINI center, see pages 16, 17.< ASC+T system. Allow only authorized tech- drive with the ASC+T switched on nicians to perform service procedures on whenever possible.< the ASC+T.< Switch the ASC+T back on Briefly press the switch once again. Indicator lamp goes out. 60 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • DYNAMIC STABILITY CONTROL (DSC) * OVERVIEW The concept Indicator lamp This system maintains driving stability The indicator lamp on the instru- even in critical driving situations. ment cluster will go out shortly The system optimizes vehicle stability after the ignition has been switched on, see pages 16, 17. CONTROLS during acceleration and when starting from a full stop, as well as optimizing trac- tion. In addition, it recognizes unstable If the indicator lamp flashes: vehicle conditions, such as under- or over- DSC controls the drive and braking forces. steering, and, as far as is possible within the laws of physics, helps keeping the If the indicator lamp fails to go out OPERATION vehicle on a steady course by reducing the after the engine is started, or if it rpms and brake applications to the indi- comes on during normal driving and stays To switch off the DSC on: vidual wheels. Briefly press the switch. If the system is either defective or was The DSC is operational every time you start The indicator lamp stays lit. switched off with the button, then the the engine. DSC contains the functions stabilizing applications described are no Antilock Brake System ABS/Electronic Brake When driving with snow chains, it may be effective to switch off the DSC for a brief longer available. The vehicle will remain Force Distribution EBV/ASC+T. REPAIRS period. completely operational, however, without DSC. The laws of physics cannot be To maintain stability, always drive In the event of a malfunction, please see repealed, even with DSC. An appro- with the DSC switched on whenever your MINI center, see pages 16, 17.< priate driving style always remains the responsibility of the driver. We therefore possible.< urge you to avoid using the additional DATA safety margin of the system as an excuse To switch DSC back on for taking risks. Briefly press the switch once again. Do not make any modifications to the DSC Indicator lamp goes out. system. Allow only authorized technicians to perform service procedures on the DSC.< INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 61
    • FLAT TIRE MONITOR The concept Flat tire The tire inflation pressure is determined The indicator lamp in the instru- from the signals of the ABS sensors. ment cluster informs you by The system provides an alert whenever the flashing when the tire inflation tire inflation pressure drops below the pressure of a tire drops in relation to any pressure in any other tire. other tire. In addition, an acoustic signal is sounded. Requirement > Vehicles with safety (run-flat) tires, see So that the system can "familiarize" itself notes on pages 110, 80, 84 with the correct inflation pressure, please > Vehicles with normal tires, see notes on do the following: pages 106, 80. 1. Check the tire inflation pressure in all Initializing the system tires The Flat Tire Monitor cannot alert you Only initialize the system if the inflation 2. Compare them with the inflation pres- to severe and sudden tire damage pressure, e. g. after a tire change, has been sure table, see page 81, and adjust the caused by external factors. Another factor corrected. pressures if necessary which the Flat Tire Monitor does not recog- nize is the balanced and very gradual pres- 1. Ignition key in position 2 3. Initialize the system. sure loss that takes place in all tires over an 2. Press the button long enough for the extended period of time.< yellow indicator lamp in the instrument Check the tire inflation pressure cluster to light up for a few seconds regularly and correct it if necessary, Malfunctions 3. Start the engine. see page 80.< As long as there is still a malfunction, the After a few minutes driving time, the Flat yellow indicator lamp on the instrument Tire Monitor sets the current inflation pres- cluster will stay lit up. sure in the tires as the target values to be The indicator lamp also lights up in the monitored. event of a system malfunction. Please contact your MINI center in these cases. 62 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • FLAT TIRE MONITOR PARK DISTANCE CONTROL (PDC)* OVERVIEW Do not initialize the system when The concept System malfunctions will be indicated by snow chains are fitted. When driving The PDC assists you when you back into a a continuous high-pitched tone when the with snow chains, false alarms can occur or parking space. A signal warns you of the system is activated the first time. Please pressure losses might not be detected.< distance to an obstacle. To do this, four have your MINI center resolve the problem. ultrasonic sensors in the rear bumper CONTROLS In the following situations false measure the distance to the nearest object. Even with PDC, final responsibility for alarms can also occur under certain The range for the sensors located at both estimating the distance between the circumstances or the detection of inflation rear corners ends approx. 2 ft (60 cm) vehicle and any obstructions always pressure loss can be delayed: behind the bumpers. The range for the two remains with the driver. Even when sensors > When driving on roads covered with middle sensors is slightly less than 5 ft are involved, there is a blind spot in which OPERATION snow or on other slippery road surfaces (1.5 meters). objects cannot be detected. Moreover, the > A sporty driving style (slip at the driven detection of obstructions can approach the The system starts to operate automatically wheels, high lateral accelerations).< physical limits of ultrasonic measurement, about one second after you select reverse as occurs e. g. in the case of thin and with the ignition key in position 2. PDC is wedge-shaped objects. deactivated when you shift back out of Certain sources of sound, such as a loud reverse. radio, could drown out the PDC signal REPAIRS tone.< Acoustical signals The distance to the nearest object is indi- Keep the sensors clean and free of ice cated by a tone sounding at various inter- or snow in order to ensure that they vals. As the distance between vehicle and will continue to operate effectively. object decreases, the intervals between the Do not apply high pressure spray to the tones become shorter. A continuous tone sensors for a prolonged period of time. DATA indicates the presence of an object less Always maintain a distance of more than than 9 in (20 cm) away. 4 in (10 cm).< The warning signal is canceled after approx. three seconds if the distance to the obstacle remains constant during this time INDEX (if you are moving parallel to a wall, for instance). Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 63
    • AIR CONDITIONER SYSTEM 1 Air onto the windshield and onto the 4 Temperature 65 8 Air distribution side windows 5 Windshield heating 65 9 Recirculated-air mode 65 2 Air for the upper body area 66 6 Blower for air supply 65 10 Rear window defroster 65 3 Air for the front and rear footwells 7 Air conditioner 65 64 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • AIR CONDITIONER SYSTEM OVERVIEW Air supply Rear window defroster Air conditioner You can select blower speeds Rear window defroster switched Air conditioner operation from 1 to 4. Position 0: blower is on: switched on: switched off. The button for Indicator lamp lights up. Indicator lamp lights up. recirculated-air mode fully blocks As long as the indicator lamp is lit, the The air is cooled and dehumidified and – CONTROLS the supply of air from outside. heating operates at high power output depending on the temperature setting – Heating and ventilation operate as of posi- (rapid defrosting). rewarmed. tion 1. Indicator lamp goes out. After the engine start, the windshield can The heating continues to run with reduced fog over briefly. Temperature power output and then switches itself off OPERATION Condensation forms in the air condi- Turn to the right (red) to increase automatically. tioner system during operation, and the temperature of the Windshield heating* then exits under the vehicle. Traces of passenger compartment. condensed water under the vehicle are Rapid heating: turn to the Windshield heating switched on: therefore normal.< extreme right. Then select a pleasant inte- Indicator lamp lights up. rior temperature. As long as the indicator lamp is Recirculated-air mode lit, the heating operates at high power REPAIRS output (rapid defrosting). Supply of outside air into the Air distribution vehicle is blocked: indicator lamp Air distribution in upper body Indicator lamp goes out. lights up. region , upper body region The heating continues to run with reduced The air within the vehicle is recirculated. and footwell , footwell , power output and then switches itself off footwell and windows and automatically. Do not run the recirculated-air mode windows . DATA for longer than approx. 30 minutes, All intermediate positions are possible, see as otherwise the air quality in the interior illustration and overview on page 64. will deteriorate.< If the windows fog over in the recir- culated-air mode, switch the recircu- INDEX lated-air mode off and increase the air supply as required.< Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 65
    • AIR CONDITIONER SYSTEM Microfilter The microfilter removes dust and pollen from the incoming air. Your MINI center will replace it during routine maintenance. A substantial reduc- tion in the air supply indicates that the filter must be replaced before scheduled maintenance. Draft-free ventilation Defrosting and demisting the Air supply for the upper body area: windshield and side windows Button 1: open and close the vent outlets 1. Set the rotary blower speed control for as required by turning. the airflow rate to position 4 The points indicate the position in each 2. Turn the rotary temperature control case. completely to the right (red) 3. Rotary control for air distribution in posi- Vent 2: change the direction of the airflow tion by swiveling. 4. To defrost the rear window: switch on the rear window defroster and, if required, the windshield heating. 66 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • AUTOMATIC CLIMATE CONTROL* OVERVIEW CONTROLS OPERATION REPAIRS 1 Air onto the windshield and onto the 5 Interior temperature sensor – please 10 Temperature 68 side windows keep clear and unobstructed DATA 11 Display for temperature and air 2 Air for the upper body area, see page 69 6 Recirculated-air mode 68 supply 68 3 Air for the front and rear footwells 7 Air conditioner 68 12 Blower for air supply 69 4 Rear window and windshield 8 Automatic air distribution and 13 Defrosting and demisting the heating 68 supply 68 windshield and side windows 69 INDEX 9 Switching the automatic climate 14 Individual air distribution 69 control on/off 68 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 67
    • AUTOMATIC CLIMATE CONTROL* Automatic air distribution and supply After the engine start, the windshield can Rear window defroster and windshield Automatic program (AUTO): fog over briefly. Switching on the air condi- heating* Indicator lamp lights up. tioner reduces condensation on the Rear window defroster and wind- Automatic adjustment of the air distribu- windows. shield heating switched on: tion and the air supply and adaptation of Indicator lamp lights up. the specified temperatures to external Condensation forms in the air condi- As long as the indicator lamp is lit, the influences (outside temperature and tioner system during operation, and heating operates at high power output sunlight). then exits under the vehicle. Traces of (rapid defrosting). condensed water under the vehicle are In the automatic program (AUTO), the air Indicator lamp goes out. therefore normal.< conditioner is activated automatically. The heating continues to run with reduced power output and then switches itself off Recirculated-air mode Switching the automatic climate automatically. control on/off Supply of outside air into the vehicle is blocked: Temperature The blower, heating and air condi- Indicator lamp lights up. tioner are switched off. Setting the temperature: The air within the vehicle is recirculated. To switch the automatic climate control on Move or turn the wheel in the In the automatic program (AUTO) in hot appropriate direction to increase again: weather conditions, the recirculated-air the temperature step by step. Press any button of the automatic climate mode is activated temporarily to enable control. The figures in the display provide a general faster cooling. indication of interior temperature. When Air conditioner Do not run the recirculated-air mode you start the vehicle, the system ensures Air conditioner switched on: that the selected temperature is achieved for longer than approx. 30 minutes, Indicator lamp lights up. as quickly as possible and then maintained. as otherwise the air quality in the interior The air is cooled and dehumidified and – will deteriorate.< depending on the temperature setting – Permanent heating with maximum rewarmed. power output at temperature selec- If the windows fog over in the recir- tion "HI". Permanent cooling at "LO".< In the automatic program (AUTO), the air culated-air mode, switch the recircu- conditioner is activated automatically. lated-air mode off and increase the air supply as required.< 68 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • AUTOMATIC CLIMATE CONTROL* OVERVIEW Air supply Microfilter/activated-charcoal filter Press the left or right half of the The microfilter removes dust and pollen button: the air supply varies. from the incoming air. The activated-char- coal filter provides additional protection by Defrosting and demisting the filtering gaseous pollutants from the CONTROLS windshield and side windows outside air. Press the button briefly. Your MINI center replaces this combined The indicator lamp flashes. filter as a standard part of your scheduled Ice and condensation are removed from the maintenance. A substantial reduction in rear window/windshield and side the air supply indicates that the filter must OPERATION windows. be replaced before scheduled maintenance. The rear window defroster/windshield Draft-free ventilation heating is switched on automatically. It can Air supply for the upper body area: be switched off again separately. Button 1: open and close the vent outlets Press the button for a longer period. as required by turning. Only air to the windshield. The points indicate the position in each REPAIRS case. Individual air distribution Vent 2: change the direction of the airflow Combine the air distribution by swiveling. yourself. This switches off the automatic program. DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 69
    • GLOVE COMPARTMENT ASHTRAY/BEVERAGE HOLDER CIGARETTE LIGHTER To open: Ashtray From ignition key position 1: Pull the handle. The ashtray is located in one of the Press the cigarette lighter in. The light goes on. beverage holders in the center console. Remove as soon as the lighter jumps back In the rear, an ashtray can also be fitted in out. To close: the beverage holder at the end of the Fold the door up. center console. Hold or touch the hot cigarette lighter by the knob only. Holding or To prevent injury in the event of an Beverage holders touching it in other areas could result in accident, close the glove compart- There are two beverage holders at the front burns. < ment immediately after use.< of the center console. Another is located at the end of the center console. Lighter socket Suitable for attaching power supplies for flashlights, car vacuum cleaners, etc., up to a rating of approx. 200 Watts at 12 Volts. Avoid damaging the socket with plugs of different shapes or sizes. 70 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • LUGGAGE COMPARTMENT COVER FOLDABLE REAR BACKREST OVERVIEW When the tailgate is opened, the luggage compartment cover is also raised. Never place heavy or hard objects on the luggage compartment cover, as CONTROLS otherwise occupants could be injured during braking maneuvers.< The warning triangle* is located beneath the luggage compartment OPERATION cover, see page 113. Comply with legal requirements requiring you to carry a hazard warning triangle in Removal Unlock and fold the vehicle.< To load bulky luggage, the compartment 1. Pull lever cover can be removed. 2. Fold the rear backrest forwards. 1. Remove the retaining straps on the tailgate When folding the backrest back into REPAIRS 2. Pull the luggage compartment cover out its original position always ensure towards the rear. that the detent engages securely. A loose backrest might fail to prevent cargo from entering the passenger compartment during sudden braking or evasive maneu- vers, posing a potential hazard to occu- pants.< DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 71
    • LOADING CARGO Stowing cargo > For very heavy loads when the rear seat Securing the load > Load heavy cargo as far forward as is not occupied, secure each safety belt in > For small, light items, secure using the possible – directly behind the backrests – the opposite buckle. This provides addi- luggage compartment net* or elastic and as low as possible tional stabilization for the rear backrests. straps > Cover sharp edges and corners > For large, heavy items, see your MINI > Do not pile objects higher than the top center for load-securing devices*. edge of the backrest Lashing eyes are provided at the inner corners of the luggage compartment for attaching these load-securing devices > Comply with the information enclosed with the load-securing devices. 72 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • LOADING CARGO ROOF-MOUNTED LUGGAGE RACK * OVERVIEW Always position and secure the load When loading a roof-mounted carefully. If you do not, it can luggage rack, ensure that there is endanger the passengers during braking sufficient space for the movement of the or evasive maneuvers. sliding/tilt sunroof and that no objects Do not exceed the permissible gross weight protrude into the swiveling area of the tail- CONTROLS and axle load, see page 122, otherwise the gate, as otherwise damage can occur.< vehicle's operating safety is no longer assured and you are in violation of the law. Do not secure the roof-mounted Do not stow heavy or hard objects in the luggage rack to the trim panels/ passenger compartment without first strips: the lack of a secure hold could lead OPERATION securing them. Otherwise they would be to damage or accidents.< thrown around during braking and evasive maneuvers and endanger the occupants.< Special roof-mounted luggage racks for your MINI are available as acces- sories from your MINI center.< REPAIRS DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 73
    • 74 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW OVERVIEW CONTROLS CONTROLS OPERATION OPERATION, CARE, MAINTENANCE REPAIRS OWNER SERVICE PROCEDURES DATA TECHNICAL DATA INDEX INDEX Operation 75 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • BREAK-IN PROCEDURES GENERAL DRIVING NOTES To ensure that your vehicle provides Tires Parking the vehicle maximum economy throughout a long Due to technical factors associated with Condensation forms in the air conditioner service life, we request that you comply their manufacture, tires do not achieve system during operation, and then exits with the following information: their full traction potential until after an under the vehicle. Traces of condensed initial break-in period. We therefore ask water under the vehicle are therefore Engine you to drive with extra care during the first normal. Up to 1,200 miles (2,000 km): 200 miles (300 km). Attempt to constantly vary both vehicle Brakes and engine speed during these initial miles Brake system Do not rest your foot on the brake while remembering to avoid engine speeds Approx. 300 miles (500 km) must be driven pedal while driving. Even light but in excess of 4,500 rpm and/or vehicle before the brake pads and rotors achieve consistent pedal pressure can lead to high speeds of over 95 mph (150 km/h). the optimum pad-surface and wear temperatures, brake wear and possibly Absolutely avoid using the full-throttle or patterns required for trouble-free opera- even brake failure.< kickdown position for the accelerator. tion and an extended service life. Once you have driven 1,200 miles Hydroplaning (2,000 km), both the engine and vehicle Clutch When driving on wet or slushy roads, speed can be gradually increased. Roughly 300 miles (500 km) must be driven reduce road speed. If you do not, a You should also comply with these break-in before the clutch starts to operate at wedge of water can form between tires and procedures if the engine has to be replaced optimum efficiency. Remember to engage road surface. This phenomenon is charac- at a later point. the clutch carefully during this initial terized by a partial or complete loss of period. contact between the tires and the road surface. The ultimate results are loss of steering and braking control.< 76 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • GENERAL DRIVING NOTES REFUELING OVERVIEW Driving through water Simple and environmentally friendly Do not drive through water on the Always observe all safety precautions road if it is deeper than 1 ft (30 cm), posted at the service station when and then only at walking speed at the handling fuel.< most. Otherwise, the vehicle's engine, the CONTROLS electrical systems and the transmission When refueling, insert the filler nozzle may be damaged.< completely into the filler pipe. Pulling the nozzle out of the pipe during refueling Clothes hooks > results in premature pump shutoff When suspending clothing from the > and will reduce the effect of the fuel OPERATION hooks, ensure that they will not vapor recovery system on the pump. obstruct the driver's vision. Do not hang Always switch off the engine before As long as the filler nozzle is used properly, heavy objects on the hooks. If you do so, refueling. If you do not, fuel cannot the fuel tank is full whenever the nozzle they could cause personal injury during be filled into the tank and the "Service shuts off the first time. braking or evasive maneuvers.< Engine Soon" lamp may come on.< Tank capacity: approx. 13.2 gallons (50 liters). High temperatures 1. Open the fuel filler door REPAIRS High temperatures occur in any 2. Turn the filler cap counterclockwise Close the fuel cap carefully after vehicle equipped with a catalytic 3. Put the filler cap in the bracket attached refuelling until a "click" is heard. converter. Do not remove the heat protec- to the fuel filler door. While closing, be sure not to squeeze the tion plates fitted in the area of the exhaust strap which is fastened to the filler cap. system and do not apply body-cavity Always observe all applicable precau- A loose or missing cap will activate the protectant to this area. When driving, tions and regulations when handling "Service Engine Soon" warning lamp.< DATA standing at idle or when parking, take fuels. Never carry spare fuel containers in precautions to avoid contact between the your vehicle. Whether empty or full, these Refill early to avoid damaging the hot exhaust system and easily flammable containers can leak, cause an explosion, catalytic converter; never attempt to materials (grass, hay or leaves, for and lead to fire in the event of a collision.< drive to the last drop of fuel in the tank.< example). Such contact could lead to a fire, resulting in serious personal injury and INDEX property damage.< Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 77
    • FUEL SPECIFICATIONS ANTILOCK BRAKE SYSTEM (ABS) The engine uses lead-free gasoline only. The concept Required fuel: The ABS keeps the wheels from locking > Premium Unleaded Gasoline, while braking, thereby enhancing active driving safety. min. 91 AKI. AKI = Anti Knock Index. ABS also includes Electronic Brake Force Distribution (EBV). Do not use leaded fuels. The use of leaded fuels will cause permanent Braking with ABS damage to the emissions-control system's To achieve optimal performance from ABS oxygen sensor and the catalytic when reacting to critical situations you converter.< should apply maximum pressure to the brake pedal ("panic stop"). Since the vehicle maintains steering responsiveness, you can nevertheless avoid possible obstacles with a minimum of steering effort. Pulsation of the brake pedal in conjunction with the sound of hydraulic regulation indi- cates to you that you are driving at the limit and reminds you to readapt your vehicle's speed to road surface conditions. 78 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • BRAKE SYSTEM OVERVIEW Brake fluid level It is a good idea to periodically dry the Brake pads If the brake fluid level is too low and brake brakes with a gentle application when For your own safety: use only brake pedal travel has become longer, there may driving in rain and on wet roads. pads that the manufacturer has be a defect in one of the brake system's Monitor traffic conditions to ensure that released for your particular vehicle model. hydraulic circuits. this maneuver does not endanger other The manufacturer cannot evaluate non- CONTROLS road users. The heat generated in this approved brake pads to determine if they Proceed to the nearest MINI center. process helps dry the brake pads and rotors are suited for use, and therefore cannot Higher brake application pressure to ensure that your brake system will ensure the operating safety of the vehicle may be necessary under these conditions, respond with undiminished efficiency if they are installed.< there may be slight "pull" to one side, and when you need it. OPERATION brake pedal travel may be longer. Please Extended or steep mountain descents remember to adapt your driving style should be driven in the gear or in the accordingly.< driving position in which only minimal peri- odic brake application is required. This Disc brakes helps avoid placing excessive loads on the When the vehicle is driven only occasion- brake system. Stay within the allowable ally, during extended periods when the speed range, refer to page 55. REPAIRS vehicle is not used at all, and in operating conditions where brake applications are Do not coast with the clutch pressed less frequent, there is an increased or with the transmission or selector tendency for corrosion of the brake rotors lever in Neutral. Do not coast with the and accumulation of contamination on the engine switched off. The engine provides brake pads. This occurs because the no braking effect when the transmisson is in neutral and there is no power-assist for DATA minimal pressure that must be exerted by the pads to clean the rotors by brake appli- braking when the engine is switched off.< cations is not reached. Corrosion on brake rotors is signaled by a running or pulsation during braking; even extended subsequent braking will not cure INDEX this phenomenon. Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 79
    • TIRE INFLATION PRESSURE Information for your safety The factory-approved radial tires are matched to the vehicle and have been selected to provide optimum safety and driving comfort if used properly. It is not merely the tire's service life, but also driving comfort and – above all else – driving safety that depend on the condition of the tires and the maintenance of the specified tire pressure. Incorrect inflation pressure is a frequent cause of tire damage. It also significantly Inflation pressures are on a sticker attached Checking the inflation pressure on the influences the roadholding ability of your to the B-pillar and visible with the driver's space-saver spare tire* MINI. door open. There is a valve extension accessible from the outside on the bumper for checking the Check tire inflation pressures regularly Checking tire inflation pressures inflation pressure. – at least every two weeks and before All pressures are specified in the standard beginning a longer trip. Failure to observe units of pressure for your country (bar, psi, Safety (run-flat) tires* these precautions can result in incorrect tire kilopascal), and apply to cold tires (tires at Safety tires are an optional extra consisting pressures, which cause instable handling ambient temperature). of self-contained tires and special rims. The response as well as tire damage, and can Vehicles with Flat Tire Monitor: tire reinforcement ensures that the tire ultimately lead to an accident. After correcting the tire inflation pressure, retains residual safety in the event of pres- Also check the inflation pressure on the reinitialize the Flat Tire Monitor, see sure drop and driving remains possible to a space-saver spare tire.< page 62. restricted degree. The vehicle is equipped with a Flat Tire Monitor which indicates a Comply with tire approval flat-tire. specifications More information, see pages 62, 110. The specified pressures apply to the tire brands recommended by the manufacturer, which your MINI center can provide for you. 80 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • TIRE INFLATION PRESSURE OVERVIEW Model Tires Pressures specified in bar (kPa/psi) CONTROLS 175/65 R 15 2.1 (210/30) 2.1 (210/30) 2.4 (240/35) 2.4 (240/35) 195/55 R 16 2.1 (210/30) 2.1 (210/30) 2.4 (240/35 2.4 (240/35 205/45 R 17 MINI COOPER 175/60 R 16 2.3 (230/33) 2.3 (230/33) 2.6 (260/38) 2.6 (260/38) OPERATION All winter tires Space-saver spare tire 4.2 (420/61) 4.2 (420/61) 4.2 (420/61) 4.2 (420/61) 195/55 R 16 2.1 (210/30) 2.1 (210/30) 2.4 (240/35) 2.4 (240/35) 205/45 R 17 MINI COOPER S 195/55 R 16 M+S 2.3 (230/33) 2.3 (230/33) 2.6 (260/38) 2.6 (260/38) 205/45 R 17 M+S REPAIRS 175/60 R 16 M+S 2.5 (250/36) 2.5 (250/36) 2.8 (280/41) 2.8 (280/41) In the case of all-season tires, the tire inflation pressure for summer tires applies. This data only applies to tires approved and/or recommended by the manufacturer, about which your MINI center will be glad to provide information. DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 81
    • TIRE CONDITION The tread depth should not fall below Do not continue driving on depres- 0.12 in (3 mm), although e. g. European surized (flat) tires, except with safety legislation only prescribes a minimum tires. A flat tire greatly impairs steering and tread depth of 0.063 in (1.6 mm). braking response, and can lead to complete Below 0.12 in (3 mm) tread pattern depth, loss of control over the vehicle. there is an increased risk of hydroplaning, Avoid overloading the vehicle so that the even at relatively moderate speeds and permitted load on the tires is not exceeded. with only small amounts of water on the Overloading can lead to overheating and road. increases the rate at which damage Wear indicators in the tread-groove base, develops inside the tires. The ultimate see arrow, are spread around the circum- result can assume the form of a sudden air ference of the tire and are marked on the loss. Tire tread/tire damage side wall of the tire with TWI – Tread Wear Unusual vibrations while driving, e. g. Inspect your tires frequently for tread wear, Indicator. driving over a curb or similar, can indicate signs of damage and for foreign objects The indicators in the tread indicate at tire damage or other damage to the lodged in the tread. Check the tread depth. 0.063 in (1.6 mm) tread depth that the vehicle. This is also true for irregularities in legally permitted wear limit has been the vehicle's handling characteristics, such reached. as a pronounced tendency to pull to the left or right. Should this occur, respond by immediately reducing your speed. Proceed carefully to the nearest MINI center or professional tire center, or have the vehicle towed in to have its wheels and tires inspected. Tire damage (up to and including blowouts) can endanger the lives of both the vehicle occupants and other road users.< 82 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • TIRE REPLACEMENT OVERVIEW To maintain good handling and vehicle The relative performance of tires depends Sustained high temperature can cause the response, use only tires of a single tread upon the actual conditions of their use, material of the tire to degenerate and configuration from a single manufacturer. however, and may depart significantly reduce tire life, and excessive temperature The manufacturer of your MINI tests and from the norm due to variations in driving can lead to a sudden flat tire. The grade C approves wheel and tire combinations. habits, service practices and differences in corresponds to a level of performance CONTROLS road characteristics and climate. which all passenger car tires must meet Do not use retreaded tires, since under the Federal Motor Car Safety Stan- driving safety may be impaired. This Traction dard No. 109. Grades B and A represent is due to the possible variations in casing The traction grades, from highest to lowest, higher levels of performance on the labora- structures and, in some cases, to their are AA, A, B, and C. tory test wheel than the minimum required OPERATION extreme age, which can lead to a decrease by law. Those grades represent the tire's ability to in their durability.< stop on wet pavement as measured under The temperature grade for this tire is controlled conditions on specified govern- DOT Quality Grades established for a tire that is properly ment test surfaces of asphalt and concrete. Tread wear inflated and not overloaded. Excessive A tire marked C may have poor traction speed, underinflation, or excessive loading, Traction AA A B C performance. either separately or in combination, can Temperature A B C REPAIRS cause heat buildup and possible tire The traction grade assigned to this failure.< All passenger car tires must conform tire is based on straight-ahead to Federal Safety Requirements in braking traction tests, and does not include Uniform Tire Quality Grading addition to these grades.< acceleration, cornering, hydroplaning, or peak traction characteristics.< Quality grades can be found where appli- cable on the tire sidewall between tread Tread wear shoulder and maximum section width. For DATA Temperature The tread wear grade is a comparative example: rating based on the wear rate of the tire The temperature grades are A (the highest), when tested under controlled conditions B, and C, representing the tire's resistance Tread wear 200 on a specified government test course. to the generation of heat and its ability to Traction AA dissipate heat when tested under Temperature A For example, a tire graded 150 would wear controlled conditions on a specified indoor INDEX one and one-half (1 g) times as well on the laboratory test wheel. government course as a tire graded 100. Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 83
    • TIRE REPLACEMENT WHEEL AND TIRE COMBINATIONS Tire age The right choice The correct wheel and tire combina- The date on which the tire was manufac- The factory-approved normal tires and tion affects various systems that tured is indicated by the code on the side- safety tires are matched to the vehicle and would otherwise be impaired, e.g. ABS, wall: have been selected to provide optimum ASC+T and DSC. driving safety and the desired driving For this reason, use only tires of the same DOT ... 1202 indicates that the tire was manufacture and tread configuration. In manufactured in Week 12 of the year 2002. comfort. the event of a flat tire, for example, The manufacturer of your MINI recom- remount the approved wheel and tire Never mount wheels and tires that mends replacement of all tires – including combination as soon as possible.< have not been specifically approved the space-saver spare tire, after no more by the manufacturer for use on your partic- than 6 years. Storage ular model. Although other wheels and tires may theoretically have the same Store tires in a cool, dry place, protecting Safety (run-flat) tires* dimensions, variations in factors such as them against light whenever possible. For replacement, use only safety tires, manufacturing tolerances can result in Protect the tires against contact with oil, as in the event of a flat tire there is no contact between tire and bodywork, ulti- grease and fuel. space-saver spare tire. mately leading to serious accidents. The You will recognize safety tires by a circular manufacturer cannot evaluate non- Tire changes between axles symbol containing the letters RSC on the approved wheels and tires to determine if Depending on individual operating condi- side of the tire, see pages 110, 80.< they are suited for use, and therefore tions, different wear patterns appear on cannot ensure the operating safety of the the front and rear axles. In the interests of vehicle if they are fitted.< safety and optimized handling characteris- tics, a change between the axles is not The manufacturer has tested certain tire recommended. brands in each size, categorized them as safe for use on the road, and approved them. Contact your MINI center for more details. 84 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • WINTER TIRES SNOW CHAINS* OVERVIEW Choosing the right tire Observing speeds The use of narrow-link snow chains is The manufacturer recommends winter Never exceed the maximum speed permitted in pairs only and only on tires (M+S radial tires) for driving in adverse for which the tires are rated. the front wheels with the following tires: winter road conditions. While so-called all- Unprofessional attempts by laymen to 175/65 R 15 season tires (M+S designation) provide service tires can lead to damage and acci- 175/60 R 16 CONTROLS better winter traction than summer tires dents. When fitting, comply with the manufac- with the load ratings S, T, H, V, W, they do Have this work performed by skilled profes- turer's instructions.< not achieve the performance of winter sionals only. Your MINI center will be glad tires. to assist you with both their expertise and With chains, do not exceed a speed of 30 mph (50 km/h).< In the interest of safe tracking and steering the proper equipment for your vehicle.< OPERATION response, install winter tires made by the After fitting the snow chains, do not same manufacturer having the same tread Tire condition, tire inflation pressure activate the Flat Tire Monitor. configuration on all four wheels. Once the tire wears to below 0.16 in When driving with snow chains, it can be Before purchasing winter tires, check (4 mm), winter tires display a percep- helpful to switch off the ASC+T or DSC for whether your MINI is fitted with safety tible decrease in their ability to cope with a brief period, see pages 60, 61.< tires. You will recognize safety tires by a winter driving conditions, and should be circular symbol containing the letters RSC replaced in the interest of safety.< REPAIRS on the side of the tire, see page 110. In this case, use only safety tires, as in the event of Comply with the specified tire inflation a flat tire there is no space-saver spare tire. pressures and be sure to have the wheel and tire assemblies balanced every time Only winter tires recommended by the you change the tires. manufacturer of your MINI should be fitted. Any MINI center will be glad to DATA advise you on the selection of the right winter tires for the relevant operating conditions. INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 85
    • HOOD Do not attempt to service your vehicle if you do not have the required technical background. Before working in the engine compartment, switch off the engine and allow it to cool down. Before working on the electrical system, always disconnect the battery first. For all work on the vehicle, comply with the appropriate information and instructions. Failure to work in an informed, professional manner when servicing components and materials constitutes a safety hazard for vehicle occupants and other road users. To unlock To open If you are not familiar with the guidelines, Pull the lever in the right door area beneath 1. Reach under the hood please have the operations performed by the instrument panel. 2. Pull the release lever your MINI center.< 3. Open the hood. To close Allow the hood to fall from a height of about 12 in (30 cm). To avoid injuries, be sure that the travel path of the hood is clear when it is closed, as with all closing procedures. If it is determined that the hood is not completely closed while driving, stop immediately and close it securely, see also page 16.< 86 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • ENGINE COMPARTMENT – MINI COOPER OVERVIEW CONTROLS OPERATION REPAIRS 1 Reservoir for windshield washer 3 Engine oil filler neck 90 6 Reservoir for headlamp cleaning system 89 system 89 DATA 4 Battery 111 2 Coolant expansion tank 91 5 Brake fluid reservoir 92 7 Engine oil dipstick 89 INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 87
    • ENGINE COMPARTMENT – MINI COOPER S 1 Reservoir for windshield washer 3 Engine oil filler neck 90 6 Reservoir for headlamp cleaning system 89 4 Auxiliary terminal for jump- system 89 2 Coolant expansion tank 91 starting 113 7 Engine oil dipstick 89 5 Brake fluid reservoir 92 88 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • WASHER FLUID ENGINE OIL OVERVIEW The oil volume between the two marks on the dipstick ("MIN", "MAX") corresponds to approx. 1.1 quarts (1 liter). Do not fill beyond the upper notch on the dipstick. Excess oil will damage the engine. CONTROLS OPERATION Headlamp* and Measuring the oil level windshield washer system 1. Park the vehicle on a level surface Capacity approx. 2.6 quarts (2.5 liters) per 2. Switch off the warmed-up engine reservoir. 3. Pull the dipstick out after approx. Fill with water and – if required – with anti- 5 minutes and wipe it off with a lint-free REPAIRS freeze (according to manufacturer's recom- cloth, paper towel, or similar material mendations). 4. Carefully push the dipstick all the way into the guide tube and pull it out again. We recommend that you mix the The oil level must be between the two washer fluid before adding it to the marks on the dipstick. reservoir.< As with fuel economy, oil consumption is directly influenced by your driving style and DATA Antifreeze agent for the washer vehicle operating conditions. systems is flammable. Always keep it well away from sparks and open flames, and store it in tightly closed containers well out of the reach of children. Always observe INDEX the instructions for use provided on the container.< Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 89
    • ENGINE OIL Continuous exposure to used oil has Approved engine oils caused cancer in laboratory testing. The quality of the engine oil selected has For this reason, any skin areas that come critical significance for the operation and into contact with oil should be thoroughly service life of an engine. Based on extensive washed with soap and water. testing, the manufacturer approves only Always store oil, grease, etc., out of reach of certain grades of engine oil. children. Comply with all warning labels and information on lubricant containers.< You can find out from your MINI center which individual oils have Comply with the applicable environ- been approved by the manufacturer.< mental laws regulating the disposal of used oil.< Alternative oil specifications Adding engine oil If you are unable to obtain one of these oils, Only top up oil when the oil level has you may use small volumes of other oils dropped to just above the lower notch of between oil changes in exceptional cases. the dipstick, but before it goes below this mark. One of the following oil specifications must be on the oil package: MINI engines are designed to operate > Preferred: BMW Longlife-01 without oil additives; the use of addi- > Alternative: BMW Longlife-98, tives could lead to damage in some cases. BMW Longlife or ACEA A3. This also applies to the CVT, the manual transmission, and the differential.< The manufacturer recommends that you have the oil changed only at your MINI center. 90 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • COOLANT OVERVIEW Do not add coolant to the cooling To add coolant system when the engine is hot. MINI COOPER: Escaping coolant can cause burns. 1. Slowly open the cap by turning it with To avoid the possibility of damage later on, the tab to allow accumulated pressure never use anything other than factory- CONTROLS toescape. approved, nitrite and amino-free extended- 2. Pull open the cap completely. duty antifreeze with corrosion inhibitor. 3. If the coolant is low, slowly add coolant Every MINI center is aware of these. until the correct level is reached – do not Antifreeze and anti-corrosion agents are overfill. hazardous to health. Always store these MINI COOPER S: OPERATION agents in tightly-closed original containers kept well away from the reach of children. 1. Open the cap by turning it slightly coun- Extended-duty antifreeze with corrosion The illustration shows an example of the terclockwise to allow accumulated pres- inhibitor contains the flammable coolant tank on the MINI COOPER. sure to escape. substance ethylene-glycol. For this reason, 2. Unscrew the cap completely and open. do not spill extended-duty antifreeze with Checking coolant level 3. If the coolant is low, slowly add coolant corrosion inhibitor on hot engine parts. It Correct coolant level for cold engine until the correct level is reached – do not REPAIRS could catch fire and cause serious burns.< (approx. 68 7/20 6): overfill. The coolant consists of water and Comply with the applicable environ- Up to the mark "MAX" of the transparent extended-duty antifreeze with corrosion mental laws regulating the disposal expansion tank. inhibitor. The mixing ratio of 50 to 50 must of extended-duty antifreeze with corrosion be maintained all the year round due to the inhibitor.< Only open the cap of the expansion tank when the engine has cooled required corrosion resistance. No other additives are required. DATA down. The needle on the coolant tempera- ture gauge in the instrument cluster must Replace the coolant every 4 years. be no higher than in the first quarter, otherwise there is a danger of scalding.< INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 91
    • BRAKE FLUID Brake fluid loss may result in extended brake pedal travel. If this occurs, refer to the information on page 79. Brake fluid is hygroscopic, that is, it absorbs moisture from the air over time. In order to ensure the brake system's safety and reliability, have the brake fluid changed every two years by a MINI center, see also page 57 and the Service and Warranty Information Booklet (US models)/ Warning lamp Warranty and Service Guide Booklet (Cana- If the brake warning lamp comes dian models). Brake fluid is toxic and also on with the parking brake released: damages vehicle paintwork. Always store The brake fluid level is too low, see brake fluid in tightly-closed original page 15. containers kept well away from the reach Brake warning lamp for Canadian of children. models. Do not spill the brake fluid and do not fill the brake fluid reservoir beyond the "MAX" mark. The brake fluid could ignite upon Adding brake fluid contact with hot engine parts and cause serious burns.< To add brake fluid or to determine and correct the cause of brake fluid loss, consult Comply with the applicable environ- your MINI center. Your MINI center is mental laws regulating the disposal familiar with the specifications for factory- of brake fluid.< approved brake fluids (DOT 4). 92 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • MINI MAINTENANCE SYSTEM OVERVIEW Service Interval Display Service and Warranty Information While conventional systems specify main- Booklet (US models)/Warranty and tenance according to rigid distances driven, Service Guide Booklet (Canadian the MINI Maintenance System takes models) account of the operating conditions of the For additional information on maintenance CONTROLS vehicle, for distances can be driven in many intervals and procedures, please refer to different ways: the Service and Warranty Information From the point of view of maintenance, Booklet (US models) or the Warranty and 60.000 miles (100.000 km) of short- Service Guide Booklet (Canadian models). distance driving cannot be regarded in the As a precaution against rust, it is advisable OPERATION same way as 60.000 miles (100.000 km) of to have the body checked for damage from long-distance highway travel. rocks or gravel at the same time, depending The MINI Maintenance System has been designed as a reliable means of providing The condition-based MINI Maintenance upon operating conditions. maximum driving and operating safety – System includes the Engine Oil Service and and as cost-effectively as possible for you. Inspections I and II. Have your vehicle's maintenance Determining the maintenance intervals and repairs performed at your MINI Please bear in mind that regular mainte- according to the actual use of the vehicle center. REPAIRS nance is not only necessary for the safety covers every kind of operating situation. Be sure that all maintenance work is of your vehicle, but also plays a significant People who drive very little – much less confirmed in the Service and Warranty role in maintaining the resale value of the than 6.000 miles (10.000 km) per year – Information Booklet (US models) or the vehicle. should have the engine oil changed at least Warranty and Service Guide Booklet (Cana- every 2 years since oil deteriorates over dian models). These entries are your proof time, regardless of use. that the vehicle has received regular main- DATA tenance. They are also a requirement for For more information on the Service warranty claims.< Interval Display, see page 57. INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 93
    • CARING FOR YOUR VEHICLE Suitable car-care products Rod antenna Care of upholstery Use the cleaning and car-care prod- If necessary, before entering a car Depressions that come about on the uphol- ucts available at your MINI center.< wash or garage with elevator ramp stery material of the seats in daily use can for example, remove the rod antenna. To be brushed out using a slightly damp brush Washing your vehicle do so, grip the rod antenna at the base and against the grain. You can wash your new MINI from the unscrew it from the antenna foot by The fact that velour lays down is not a outset in automatic car washes, though turning it to the left.< quality defect, but rather is inevitable in you should use brushless car washes. the case of home textiles or clothing mate- Headlamps rials. When using steam jets or high-pres- When cleaning the headlamps, In the case of strong sunlight and longer sure washers, ensure that you keep please observe the following: do not parking periods, cover the seats or all the jets sufficiently far away from the clean by wiping with a dry cloth (scratches). windows to prevent discoloration. vehicle. If the jet is too close or the pressure Never use abrasives or strong solvents to is too high, this can lead to damage or clean the covers. Remove dirt and contami- Care of special parts initial damage that can develop into more nation (such as insects) by soaking with > Light-alloy wheels: serious damage. Water that enters vehicle shampoo and then rinsing with plenty of Use wheel cleaner especially during the components can lead to damage over the water. Always use a deicer spray to remove winter months, but do not use any long term.< accumulated ice and snow – never use a aggressive, acidic, strong alkali or rough scraper.< cleansers or steam jets above 140 7 After washing the vehicle, apply the (60 6) (observe the manufacturer's brakes briefly to dry them, otherwise Vehicle paintwork operating instructions) water can reduce braking efficiency over Regular care contributes greatly to driving > Chrome parts* such as cooler grille, door the short term and the brake rotors can safety and value retention. handles, etc.: corrode. < Environmental influences varying from one Especially if exposed to road salt, care- region to the next can affect the vehicle fully clean these parts with plenty of Switch the rain sensor off when paintwork. Please base the frequency and water and possibly with a shampoo addi- passing through an automatic car scope of car care on these various influ- tive. For additional treatment, use wash, see page 51. Failure to do so could ences. chrome polish result in damage caused by undesired wiper activation.< 94 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CARING FOR YOUR VEHICLE OVERVIEW > Rubber parts: Use only wiper blades which have Cleaning agents can contain Treat only with water or rubber care been approved by the manufac- hazardous or health-damaging products turer.< substances. For this reason, always observe > Plastic parts, imitation leather surfaces, the warnings on the package. headliner, lamp glass, covering glass for Leather care For interior cleaning, always open the doors CONTROLS the instrument cluster, as well as matt The leather* used by the manufacturer is a or windows of the vehicle. Do not use any black molded parts: high-quality natural product processed products (e.g. solvents) that are not Clean with water and, if necessary, using state-of-the-art methods, and it will intended for cleaning the vehicle.< plastic care products. Do not dampen retain its quality level for many years if seats and the headliner. Never use cared for appropriately. OPERATION solvents such as lacquer thinner, heavy- Regular cleaning and care are necessary, as duty grease remover, fuel or similar dust and road dirt scratches in pores and > Safety belts: creases and lead to heavy wear as well as Only clean using mild soap, leaving the premature brittleness of the leather belts fitted; do not dry clean, as the surface. This is why you should use a cloth fabric can be destroyed. or vacuum cleaner to remove dust from the Always unroll automatic safety belts leather on a regular basis. REPAIRS when dry. Dirty safety belts prevent unrolling and thus negatively affect As dirt and grease can slowly affect the safety protective layer of the leather, the cleaned > Floor carpets and floor mats*: leather surfaces must be treated with If heavily soiled, clean using interior leather care agent. This also helps to avoid cleaner. Floor mats can be removed to electrostatic charges. allow the interior to be cleaned DATA > Wiper blades: Clean with soapy water. Replace wiper blades twice a year, before and after the cold season. This is particularly impor- tant on vehicles fitted with a rain sensor. INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 95
    • VEHICLE IMMOBILIZATION OBD INTERFACE SOCKET TECHNICAL MODIFICATIONS Your MINI center will be glad to advise you Any MINI center will be glad to inform you on what is important if the vehicle is to be of the advisability, legal regulations and decommissioned for longer than three factory recommendations for technical months. modifications to the vehicle. To do so, they require the vehicle identification number from your vehicle documents. The interface for onboard diagnostics is located on the driver's side, behind a cover located beneath the instrument panel. The cover has the letters "OBD" on it. This interface makes it possible to access data on emissions-related components using special equipment. 96 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CALIFORNIA PROPOSITION 65 WARNING OVERVIEW California laws require us to state the following warning: Engine exhaust, some of its constitu- ents, and certain vehicle components contain or emit chemicals known to the CONTROLS State of California to cause cancer and birth defects or other reproductive harm.< OPERATION REPAIRS DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 97
    • 98 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW OVERVIEW CONTROLS CONTROLS OPERATION OPERATION, CARE, MAINTENANCE REPAIRS OWNER SERVICE PROCEDURES DATA TECHNICAL DATA INDEX INDEX Repairs 99 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • ONBOARD TOOL KIT WINDSHIELD WIPER BLADES Storage location Windshield wiper Rear window wiper The illustration shows an example of the 1. Rotate the wiper arm completely out 1. Rotate the wiper arm completely out tire change set. from the windshield from the windshield Depending on the level of equipment, your 2. Set the wiper blade at an angle 2. Turn the wiper blade as far as it will go MINI is fitted with a special onboard tool 3. Press the securing spring (arrow) to the rear, see arrow kit stored at the following locations: 4. Unhook the wiper blade towards the 3. Press the wiper blade against the limit windshield and thus out of the mounting Tire change set for space-saver spare tire: 5. Pull the wiper blade past the wiper arm 4. Press the new wiper blade into the In the luggage compartment under the toward the top mounting. floor mat. 6. Insert the new wiper blade Tool bag for safety tires: 7. Press into position until you hear it In the left of the luggage compartment, engage. behind the side trim panel beside the first- aid kit, see page 113. Use only wiper blades which have been approved by the manufac- turer.< 100 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • LAMPS AND BULBS OVERVIEW Proceed carefully when handling lamps and When cleaning the headlamps, bulbs. If you are not familiar with any of please observe the following: do not the procedures, consult your MINI center. clean by wiping with a dry cloth (scratches). Never use abrasives or strong solvents to Do not touch the glass portion of clean the covers. Remove dirt and contami- CONTROLS a new bulb with your bare hands nation (such as insects) by soaking with since even small amounts of impurities shampoo and then rinsing with plenty of burn into the surface and reduce the water. Always use a deicer spray to remove service life of the bulb. Use a clean cloth, accumulated ice and snow – never use a paper napkin, or a similar material, or hold scraper.< OPERATION the bulb by its metallic base.< Xenon lamps* Replacement bulbs are available from your 1 Low beams The service life of these bulbs is very long MINI center. H7 bulb, 55 Watts and the probability of a failure is very low, provided that they are not switched on and Whenever working on the electrical 2 High beams off an unusual number of times. If one of system, switch off the electrical H7 bulb, 55 Watts these bulbs should nevertheless fail, it is REPAIRS accessory you are working on or disconnect possible to continue driving with great the cable from the negative terminal of the The H7 bulb is pressurized. Therefore, caution using the fog lamps, provided battery. Failure to do this could result in wear safety glasses and protective traffic laws in your area do not prohibit short circuits. gloves. Failure to observe these precautions this. To prevent injuries and damage, comply can result in physical injury if the bulb with any instructions provided by the bulb breaks.< Because of the extremely high volt- manufacturer.< ages involved, any work on the xenon DATA 1. Pull off the cover panel of the corre- lighting system should be carried out by sponding lamp technically-qualified personnel only. Other- 2. Press the securing wire outwards wise, there is a risk of fatal injury.< 3. Fold the securing wire downwards 4. Remove and replace the bulb. INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 101
    • LAMPS AND BULBS Turn signal indicators, front Side turn signal indicators Fog lamps* 21 Watt bulb 5 Watt bulb H7 bulb, 55 Watts 1. Open the hood 1. Press the bulb towards the rear of the Please contact a MINI center in case of a 2. Reach into the opening for the turn vehicle and remove malfunction. signal indicators from above 2. Remove and replace the bulb. 3. Apply gentle pressure to the bulb holder while turning it to the left Side marker lamps 4. Remove and replace the bulb. Side marker lamps in the wheelhouse paneling of the bumper. Parking lamps and standing lamps Please contact a MINI center in case of a 5 Watt bulb malfunction. The parking lamps and standing lamps are integrated in the lamp housing of the turn signal indicator. 1. Turn the bulb holder to the left and pull out 2. Remove and replace the bulb. 102 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • LAMPS AND BULBS OVERVIEW CONTROLS OPERATION Tail lamps To make this clear, the illustration shows a Backup lamp Rear lamp (3): 21/5 Watt bulb dismantled tail lamp with the bulb holder Access to the lamp via the rear or underside Other bulbs: 21 Watts removed. All of the bulbs are integrated in of the bumper. the bulb holder. 1 Rear fog lamp (not active) red 1. Press the clips together 2 Turn signal indicator yellow To reach the bulb holder, remove the cover 2. Push the lamp out of the bumper REPAIRS 3 Rear lamp red of the side trim panel in the luggage 3. Apply gentle pressure to the bulb while 4 Rear lamp/brake lamp red compartment. turning it to the left 4. Remove and replace the bulb. Replacing bulbs 1. Unplug the power supply 2. Release the bulb holder, see arrow, and remove DATA 3. Apply gentle pressure to the bulb while turning it to the left 4. Remove and replace the bulb 5. Plug in the power supply receptacle 6. Press the bulb holder into position until INDEX you hear it engage. Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 103
    • LAMPS AND BULBS Center (high-mount) brake lamp License plate lamps Interior lamps LED strip on the tailgate. 5 Watt bulb Interior lamp (6 Watt xenon bulb) Please contact a MINI center in case of a 1. Apply a screwdriver to the recess and 1. Press out the lamp cover with a screw- malfunction. lever out the lamp cover driver 2. Replace the bulb. 2. Remove and replace the bulb. Reading lamps (2 x 6 Watt xenon bulbs) 1. Press out the lamp cover with a screw- driver 2. Unscrew the entire lamp with a screw- driver 3. Remove the bulb from above and replace. 104 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • LAMPS AND BULBS OVERVIEW Footwell lamps 5 Watt bulb 1. Press out the lamp cover with a screw- driver CONTROLS 2. Remove and replace the bulb. Glove compartment lamp 5 Watt bulb 1. Press out the lamp cover with a screw- OPERATION driver 2. Remove and replace the bulb. Illuminated vanity mirror Luggage compartment lamps Lamps in the vanity mirror in the sun visor. 5 Watt bulb Please contact a MINI center in case of a 1. Press the lamp cover with a screwdriver malfunction. to the left and press out 2. Remove and replace the bulb. REPAIRS DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 105
    • REPAIRING A FLAT TIRE CHANGING TIRES – MINI WITH SPACE-SAVER SPARE TIRE * Safety measures in the event of a flat Additional safety measures in the tire: event of a wheel change: change the Stop the vehicle as far as possible from wheel only on a level, firm surface which is passing traffic. Switch on the hazard not slippery. warning flashers. Avoid jacking the vehicle on a soft or slip- Turn the steering wheel to the straight- pery support surface (snow, ice, loose ahead wheel position and engage the gravel, etc.), as either the vehicle or the jack steering lock. Engage the parking brake and could slip sideways. shift into 1st or reverse gear (selector lever Do not use a wooden block or similar object in P). as a support base for the jack, as this would All passengers should be outside the prevent it from extending to its full support vehicle and well away from your imme- height and reduce its load-carrying diate working area (behind a guardrail, for capacity. Tire change set instance). Do not lie under the vehicle or start the On vehicles with a space-saver spare tire, If a warning triangle or portable hazard engine when the vehicle is supported by the tire change set is stored in the luggage warning lamp is available, set it up on the the jack – risk of fatal injury.< compartment under the floor mat. roadside at an appropriate distance from 1 Chock, folding the rear of the vehicle. Comply with all To change a space-saver tire, proceed as 2 Hubcap remover safety guidelines and regulations.< follows: 3 Wheel stud wrench > Remove the space-saver spare tire, see 4 Jack In the event of a flat tire, different proce- page 107 5 Spanner dures should be followed depending on the > Prepare the vehicle, see page 108 6 Tow fitting equipment included in your MINI: > Jack up the vehicle, see page 108 7 Lifting handle > Vehicles with space-saver spare tire, see > Fit the space-saver spare tire, see next column page 109 > Vehicles with safety tires, see page 110. > Tighten the lug bolts, see page 109 > Drive with space-saver spare tire, see page 109. 106 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CHANGING TIRES – MINI WITH SPACE-SAVER SPARE TIRE * OVERVIEW CONTROLS OPERATION Removing the space-saver spare tire 3. Screw the lifting handle from the 5. Squeeze the securing springs The screw connection of the space-saver onboard tool kit onto the thread 6. The space-saver spare tire is released spare tire is in the luggage compartment 4. Raise the lifting handle slightly and must be held by the lifting handle under the floor mat, on the base of the 7. Lower the space-saver spare tire with storage compartment for the tire change the lifting handle 8. Unscrew the lifting handle again REPAIRS set. 1. Loosen the screw connection using the wheel stud wrench 2. Take out the cover panel DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 107
    • CHANGING TIRES – MINI WITH SPACE-SAVER SPARE TIRE * Preparing the vehicle Read and comply with the safety precautions provided on page 106.< 1. Secure the vehicle to prevent it from rolling: Place the folding chock behind the front wheel on the other side of the vehicle; on downward inclines, place it in front of this wheel. If the wheel is changed on a surface with a more severe slope, take additional 9. Pull out the space-saver spare tire Jacking up the vehicle precautions to secure the vehicle from towards the rear underneath the 1. Place the jack at the jacking point closest rolling vehicle to the wheel. 2. Loosen the lug bolts by a half turn. 10. Position the space-saver spare tire with The jack base must be perpendicular to the valve facing upwards the surface beneath the jacking point 11. Unscrew the valve extension from the valve of the space-saver spare tire 12. Unscrew the dust cap from the exten- sion and attach to the space-saver spare tire. 108 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CHANGING TIRES – MINI WITH SPACE-SAVER SPARE TIRE * OVERVIEW Fitting the space-saver spare tire Driving with the space-saver spare tire 1. Unscrew the lug bolts and remove the Drive cautiously. Do not exceed a speed of wheel 50 mph (80 km/h). 2. Remove accumulations of mud or dirt You can expect changes in vehicle handling from the mounting surfaces of the CONTROLS such as delayed braking response, longer wheel and hub. Clean the lug bolts braking distances, and changes in self- 3. Fit the space-saver spare tire steering properties in marginal stability 4. Screw at least two lug bolts finger-tight limits. into opposite bolt holes 5. Screw in the remaining bolts Only one space-saver spare tire may OPERATION 6. Tighten all the lug bolts firmly in a diag- be mounted at one time. Reinstall onal pattern wheels and tires of the same size and speci- 2. Insert the jack head for jacking up in the 7. Lower the vehicle fication as soon as possible. Maintain square recess of the jacking point 8. Remove the jack. prescribed tire pressures, see page 80.< 3. Jack the vehicle up until the wheel you are changing is raised from the ground. Tightening the lug bolts Only use full hubcaps approved by The vehicle jack is designed for Tighten the lug bolts in a diagonal pattern. the manufacturer. Otherwise there is REPAIRS changing wheels only. Do not no guarantee that the hubcap fits securely. attempt to raise another vehicle model As soon as possible, have the secure The hubcap must not be fitted to the space- with it or to raise any load of any kind. To seating of the lug bolts (tightening saver spare tire, as it could be damaged.< do so could cause accidents and personal torque 72 ftlb (100 Nm)) checked using a injury.< calibrated torque wrench. Otherwise, a Check and correct the tire inflation wheel that might come loose can lead to a pressure at the earliest opportu- DATA severe accident.< nity.< Replace the defective tire as soon as possible and have the new wheel/tire assembly balanced. INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 109
    • FLAT TIRE – SAFETY (RUN-FLAT) TIRES* Flat tire Continuing driving with a damaged The yellow indicator lamp in the instru- tire ment cluster lights up to indicate a flat tire. Driving can continue under certain condi- In addition, a gong sounds, see tions with safety tires, depending on the pages 17, 62. vehicle load and the severity of the tire 1. Reduce vehicle speed carefully to under damage, at a maximum speed of 50 mph 50 mph (80 km/h), avoiding hard brake (80 km/h). applications and steering maneuvers You can determine the possible mileage for 2. Do not exceed a speed of 50 mph continued driving on the basis of the (80 km/h) following general indications: 3. Identify damaged tires; check tire infla- > Tire inflation pressure 0 bar (0 psi): You will recognize safety tires by a circular tion pressures on all four wheels at the approx. 95 miles (150 km) symbol containing the letters RSC on the next opportunity, see page 80 > Tire inflation pressure 0.5 bar – 1 bar side of the tire. 4. Correct the tire inflation pressure if you (7.2 psi – 14.5 psi): approx. 300 miles wish to continue your journey and this is (500 km) Safety tires consist of self-contained tires permitted, see next column > Tire inflation pressure greater than 1 bar and special rims. The tire reinforcement 5. Have damaged tires changed by your (14.5 psi): approx. 600 miles (1,000 km). ensures that the tire retains some residual MINI center, see page 84. safety in the event of pressure drop and driving remains possible to a restricted Your MINI center has the information degree. needed for working with safety tires and is equipped with the necessary special The reinforcement on the flanks of tools. They provide advice if you wish to the safety tires means that it is replace the tires on your MINI or wish to usually not possible to detect an air loss re-equip from summer to winter tires – or from outside.< vice versa, see also pages 80, 84, 85.< For safety reasons, do not have a damaged safety tire repaired.< 110 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • BATTERY OVERVIEW Location in the MINI COOPER Battery care The battery is located in the engine The battery is absolutely maintenance-free, compartment. that is, the original electrolyte will normally Exact location, see page 87. last for the service life of the battery under moderate climatic conditions. CONTROLS Location in the MINI COOPER S For all questions regarding the The battery is located in the luggage battery, please consult your MINI compartment under the floor mat. center. < OPERATION Charging the battery Only charge the battery in the vehicle via the terminals in the engine compartment with the engine switched off, see "Jump- starting" on page 113. Whenever working on the electrical REPAIRS system, disconnect the cable from the negative terminal of the battery. Failure to do this could result in fire hazards or injury due to short circuits.< Return used batteries to a recycling DATA point or your MINI center. Maintain the battery in an upright position for trans- port and storage. Secure the battery to prevent it from tilting during transport.< INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 111
    • FUSES If an electrical device fails, switch it off and In the interior check the fuse. On the left side of the footwell in the side Plastic tweezers that you can use to pull trim panel. fuses out of their sockets can be found in Open the cover panel of the fuse box. To do the fuse box of the interior, see next so, press the fastener. column. Do not attempt to repair a blown fuse In the engine compartment or replace it with a fuse of a different To the right of the battery. color or amperage rating. To do this could Open the cover panel of the fuse box. To do cause a fire in the vehicle resulting from a so, press the clip fastener. circuit overload.< If a fuse blows a second time, have the cause of the damage rectified by your MINI center.< 112 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • WARNING TRIANGLE * FIRST-AID KIT* JUMP-STARTING OVERVIEW Do not use spray starter fluids to start the engine. When your battery is discharged, you can use two jumper cables to start your vehicle with power from the battery in a second CONTROLS vehicle. By the same token, you can provide another vehicle with starting assistance. To do so, use only jumper cables with fully insulated terminal clamps. OPERATION Do not touch live wiring and cables on a running engine. There is a risk of The warning triangle is located beneath the The first-aid kit is located together with the fatal injury if you do this. Carefully observe luggage compartment cover. onboard tool kit in the left of the luggage the following instructions to avoid personal compartment, behind the side trim panel. injury and/or damage to either vehicle or Comply with legal requirements both vehicles.< requiring you to carry a hazard Some articles in the first-aid kit are warning triangle in the vehicle.< perishable. For this reason, check the REPAIRS expiration dates of each of the items regu- larly, and replace any whose expiration dates have passed. Source: any pharmacy. Comply with legislation requiring you to carry a first-aid kit in the vehicle.< DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 113
    • JUMP-STARTING Preparation for jump-starting Performing the jump-start 1. Check whether the battery of the support 1. Start the engine of the vehicle providing vehicle has 12 Volts and approximately the current and allow to run at a fast idle the same capacity (Ah) (printed on the speed for several minutes battery) 2. Start the engine on the vehicle with the 2. Switch off the engine of the support discharged battery in the usual manner. vehicle > If the first start attempt is not 3. Switch off any electrical systems and successful, wait a few minutes before components in both vehicles – except another attempt in order to allow the for the hazard warning flashers of the discharged battery to recharge. support vehicle. > Do not disconnect the discharged On the MINI: 1. On the MINI COOPER S, the positive battery from the vehicle electrical Before disconnecting the jumper terminal connection (for jump-starting), system cables, switch on the lighting, rear window see arrow 1, functions as the positive > Make certain that there is no contact defroster and the highest blower speed as battery terminal. between the bodywork of the two well as the engine for at least approx. Use the jumper cable (+) to set up a vehicles – short circuit hazard! 10 seconds to prevent a voltage surge from connection between the positive terminal 4. With the battery of the MINI COOPER, the regulator to the electrical systems and of the discharged battery and the positive remove the cover panel. To do so, press components.< terminal of the support battery both clips at the same time 2. Use the second jumper cable (–) to set or 3. Then disconnect the jumper cables in up the connection between the negative with the MINI COOPER S, open the cover the reverse order. terminals of both vehicles. of the positive terminal connection (for To do so: jump-starting)*, see arrow 1. Depending on the cause of the > Connect one terminal clamp to the malfunction, have the battery negative terminal and/or to an engine Connect the jumper cables or body ground of the support vehicle checked and recharged at your MINI Adhere to the sequence also when center.< > Connect the second terminal clamp to providing support for other vehicles; the negative terminal of the battery failure to observe this procedure can lead and/or to an engine or body ground of to sparks at the terminals and pose an the vehicle to be started. For the MINI, injury hazard.< see arrow 2. 114 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • TOW-STARTING AND TOWING OVERVIEW Tow bars If the tow fittings of the two vehicles are not directly opposite one another, please note: CONTROLS > Clearance and maneuvering capability will be strictly limited in corners > The inclination of the tow bar generates lateral force (critical above all if the road surface is slippery). OPERATION Do not tow a vehicle that is heavier For towing, use either a tow bar or a nylon Screw the tow fitting in until it than the towing vehicle, otherwise it rope or nylon belts that prevent sudden bottoms firmly. If this is not done, the will no longer be possible to control vehicle jerking movements. threads could be damaged. response.< Never attach tie-down hooks, chains, Tow fitting straps, or tow hooks to tie rods, control arms, or any other part of the vehicle REPAIRS The screw-in tow fitting is stored in the onboard tool kit; be sure that it remains in suspension, as severe damage to these the vehicle at all times. This fitting is components will occur, leading to possible designed for installation in the tow sockets accidents.< located at the front and rear of the vehicle. It is intended for towing on paved road surfaces only. DATA Access to tow sockets Use a suitable object (e.g. credit card, screwdriver) to press out the covers from the recess. INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 115
    • TOW-STARTING AND TOWING Tow-starting Towing On vehicles with Continuously Vari- Only tow vehicles with Continuously able automatic Transmission (CVT), it Variable automatic Transmission is not permitted to start the engine by tow- (CVT) with the front wheels raised or on a starting. The transmission could be special transport vehicle, otherwise the damaged. transmission can be damaged.< For jump-starting, see page 113.< 1 Ignition key in position 1: Only tow-start vehicles with a catalytic The brake lamps, turn signals, horn and converter when the engine is cold, other- windshield wipers can be operated wise, unburned fuel in the catalytic 2 Switch on the hazard warning flashers converter could catch fire. It is better to use (comply with national regulations). Towing with a commercial tow truck jumper cables. If the electrical system has failed, place > Do not tow with sling-type equipment 1. Switch on the hazard warning flashers some kind of warning on the towed vehicle, > Use a wheel-lift or flatbed carrier (comply with national regulations) e.g. a sign or warning triangle in the rear > Please comply with applicable towing 2. Ignition key in position 2 window. laws. 3. Engage 3rd gear 4. Tow-start with the clutch pedal pressed Ensure that if the electrical system Never allow passengers to ride in a 5. Slowly release the clutch has failed the ignition key is in posi- towed vehicle for any reason.< 6. When the engine starts, press the clutch tion 1, otherwise the steering lock could pedal again engage and make it impossible to steer the 7. Switch off the hazard warning flashers. vehicle. Have the cause of the starting problems When the engine is not running, there is no rectified by your MINI center. power-assist. This means that greater effort is required for braking and steering.< 116 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW CONTROLS OPERATION REPAIRS DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 117
    • 118 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW OVERVIEW CONTROLS CONTROLS OPERATION OPERATION, CARE, MAINTENANCE REPAIRS OWNER SERVICE PROCEDURES DATA TECHNICAL DATA INDEX INDEX Data 119 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • ENGINE DATA MINI COOPER MINI COOPER S Displacement cu in/cmm 97.52/1,598 97.52/1,598 Number of cylinders 4 4 Maximum output kW/bhp 85/115 120/163 at engine speed rpm 6,000 6,000 Maximum torque lb ft/Nm 110/149 155/210 at engine speed rpm 4,500 4,000 Compression ratio e 10.6 8.3 Stroke in/mm 3.38/85.8 3.38/85.8 Bore in/mm 3.03/77 3.03/77 Fuel-injection system Digital electronic engine-management system 120 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • DIMENSIONS OVERVIEW CONTROLS OPERATION REPAIRS DATA All dimensions specified in inches (millimeters). Smallest turning circle 35 ft (10.66 m). INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 121
    • WEIGHTS MINI COOPER MINI COOPER S Curb weight, ready for operation, with 165 lbs./75 kg load, 90% full tank, options not included with manual transmission lbs./kg 2,480/1,125 2,678/1,215 with Continuously Variable automatic Transmission (CVT) lbs./kg 2,535/1,150 – Approved gross vehicle weight with manual transmission lbs./kg 3,263/1,480 3,461/1,570 with Continuously Variable automatic Transmission (CVT) lbs./kg 3,318/1,505 – Approved front axle load lbs./kg 1,918/870 1,962/890 Approved rear axle load lbs./kg 1,543/700 1,675/760 Approved roof load (with special MINI roof rack) lbs./kg 165/75 165/75 Luggage compartment capacity cu ft/liters 5.3/150 5.3/150 122 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • CAPACITIES OVERVIEW Notes Fuel tank gal./liters approx. 13.2/50 Fuel quality, see page 78 Reserve gal./liters approx. 2.1/8 Windshield washer/ quarts/liters approx. 2.6/2.5 More details, see page 89 CONTROLS headlamp cleaning system quarts/liters approx. 2.6/2.5 Cooling system including heater circuit quarts/liters 5.6/5.3 MINI COOPER More details, see page 91 6.3/6.0 MINI COOPER S Engine oil and filter change quarts/liters 4.7/4.5 MINI COOPER Longlife Oil 4.7/4.5 MINI COOPER S More details, see page 89 OPERATION Manual transmission, incl. differential quarts/liters approx. 2.1/2 MINI COOPER Contact your MINI center for more approx. 1.8/1.7 MINI COOPER S details Continuously Variable automatic quarts/liters approx. 4.2/4.0 MINI COOPER Contact your MINI center for more Transmission (CVT), incl. differential details REPAIRS DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 123
    • ELECTRICAL SYSTEM Battery Original MINI parts and accessories 12V, 55 Ah as well as qualified advice is available at your MINI center.< Spark plugs NGK BKR 6 EQUP 124 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW CONTROLS OPERATION REPAIRS DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 125
    • 126 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • OVERVIEW OVERVIEW CONTROLS CONTROLS OPERATION OPERATION, CARE, MAINTENANCE REPAIRS OWNER SERVICE PROCEDURES DATA TECHNICAL DATA INDEX INDEX Index 127 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • Hilfsrahmen für Querverweise EVERYTHING FROM A TO Z A Antifreeze 91 B Break-in procedure 76 ABS (Antilock Brake Antilock Brake System Backrest, adjusting 33 Breaking in the vehicle 76 System) 16, 17, 78 (ABS) 16, 17, 78 Backup lamps 45 Bridging 113, 114 Activated-charcoal filter 69 Aquaplaning 76 bulb replacement 103 Bulb replacement 101 Adjusting ASC+T (Automatic Stability Bar, towing 115 backup lamps 103 backrest 33 Control plus Battery 111, 113, 114, 124 brake lamp, third 104 seats 31 Traction) 16, 17, 60 capacity 124 footwell lamps 105 steering wheel 35 Ashtray 70 charge current 15 front fog lamps 102 thigh support 33 Automatic air distribution 68 charging 111 front turn signal Air conditioner operation 65 Automatic air supply 68 maintenance 111 indicators 102 automatic climate Automatic car wash 94 Battery changing glove compartment control 68 Automatic cruise control 53 remote control 22 lamp 105 Air conditioner system 64 Automatic dimming of interior Battery, remote control 22 high beams 101 Air distribution rearview mirror 37 Beverage holder 70 interior lamps 104 air conditioner system 65 Automatic program, see Blower 65, 69 license plate lamp 104 automatic climate Automatic air BMW 6 low beams 101 control 68, 69 distribution 68 Bore 120 luggage compartment Air pressure 80 Automatic Stability Control Brake 16 lamps 105 Air recirculation 65, 68 plus Traction Brake fluid change 57 parking lamps 102 Air supply (ASC+T) 16, 17, 60 Brake fluid level 15, 79, 92 rear lamps 103 air conditioner system 65 Average fuel consumption 59 Brake hydraulic system 15 side turn signal automatic climate Average speed 59 Brake lamp indicators 102 control 69 Axle loads 122 bulb replacement 103 standing lamps 102 Air vents 66, 69 Brake pads 76, 79 tail lamps 103 Air, dry 65, 68 Brake rotors 76 vanity mirror 105 Airbags 16, 31, 37 Brake system 76, 79 All-season tires 85 brake fluid 92 Antenna 94 Brakes 79 128 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • EVERYTHING FROM A TO Z OVERVIEW C CD player, see separate Computer 58 Control elements 12 California Proposition 65 Owner's Manual average fuel Convenience feature Warning 97 Center (high-mount) brake consumption 59 sliding/tilt sunroof 25 Can holder, see Beverage lamp average speed 59 windows 25 holder 70 bulb replacement 104 cruising range 59 Convenience operation CONTROLS Car wash 94 Central locking system 23, 26 exterior temperature 59 via central locking Car-care products 94 Changing tires Condensation 65, 68 system 26 Care space-saver spare tire 106 Consumption 59 Coolant 91 chrome parts 94 Child seat 38 Consumption display 55 Coolant level 91 floor mats 95 Child-restraint systems 38 Contents 2 Coolant temperature OPERATION imitation leather 95 Chrome parts 94 Continuously Variable gauge 56 leather 95 Cigarette lighter 70 automatic Transmission Cooling 65, 68 light-alloy wheels 94 socket 70 (CVT) Copyright notice 6 of upholstery 94 Cleaning rear window 52 electronic transmission Correct sitting posture with plastic parts 95 Cleaning windshield 52 control module (EP) 48 airbags 31 rubber parts 95 Clock 58 gear display 48 safety belt 31 safety belts 95 Closing ignition 42 Cruise control 17, 18, 53 REPAIRS special parts 94 from inside 26 interlock 42 Cruising range 59 windshield wipers 95 from outside 23 manual mode 47 Cup holder, see Beverage Cargo 72 Clothes hooks 77 parking 47 holder 70 securing 72 Clutch 76 reverse gear 47 Curb weight 122 stowing 72 Cockpit 12 selector lever Currency of the Owner's Caring for your vehicle 94 Combination of wheels/ shiftlock 42, 46 Manual 7 Cassette player, see separate tires 84 shiftlock 46 Cylinders 120 DATA Owner's Manual Compact Disc player, see Sport program 47 CD changer, see separate separate Owner's Manual Steptronic 46 Owner's Manual Compression ratio 120 towing 116 tow-starting 116 transmission fault 48 INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 129
    • EVERYTHING FROM A TO Z D Display lighting 50 Electronic transmission control F Dashboard 12 Distance remaining 59 module (EP), Continuously Failure, tires 62, 106, 110 Data Door keys 22 Variable automatic Filler cap cover 77 dimensions 121 Doors Transmission (CVT) 48 Filling capacities 123 engine 120 locking 24 Emergency operation Filling, tank 123 weights 122 manual operation 25 driver's door 25 First-aid kit 113 Data, technical 120 remote control 23 sliding/tilt sunroof 30 Flat tire 62, 106 Daytime driving lamps 49 unlocking 24 tailgate 27 Flat Tire Monitor 16, 17, 62 Decommissioning the DOT Quality Grades 83 Engine 76 Floor carpets 95 vehicle 96 Drink holder, see Beverage electronics 17 Floor coverings 95 Deep water, see Water on holder 70 power output 17 Floor mats 95 roadways 77 Driving lamps 49 speed 17, 55 Fog lamps 50 Defrosting position 66 Driving notes, general 76 starting 42 Foldable rear backrest 71 Defrosting windows 69 Dry air 65, 68 switching off 43 "Follow me home" lamps 49 air conditioner system 66 Dynamic Stability Control Engine compartment Footbrake 79 automatic climate (DSC) 16, 61 MINI COOPER 87 Footwell lamps control 69 MINI COOPER S 88 bulb replacement 105 Dimensions 121 E Engine oil 89 Front fog lamps 50 Dirt on the paintwork 94 Easy Entry 33 additives 90 bulb replacement 102 Disc brakes 79 EBV (Electronic Brake Force prescribed oils 90 Front seat adjustment 31 Displacement 120 Distribution) 16 pressure 15 Fuel consumption 59 Display elements 13, 14 Electric power windows 28 Entry to the rear 33 Fuel consumption display 55 coolant temperature Electrical defect EP (electronic transmission Fuel gauge 55 gauge 56 driver's door 25 control module), Fuel preparation 120 fuel gauge 55 sliding/tilt sunroof 30 Continuously Variable Fuel quality 78 indicator and warning Electrical system 124 automatic Transmission Fuel reserve indicator 55 lamps 15 Electronic Brake Force (CVT) 48 Fuel tank capacity 123 odometer 55 Distribution (EBV) 16 Exterior finish, care 94 Fuses 112 Service Interval Display 57 Exterior mirrors 36 with navigation system 14 Eyelets, towing 115 130 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • EVERYTHING FROM A TO Z OVERVIEW G Heated Interior lamps 50 interior lamps 50, 104 Gasoline 78 outside mirrors 36 bulb replacement 104 license plate lamp 104 Gasoline gauge 55 rear window 65, 68 Interior rearview mirror 36 low beams 49, 101 Gear display 48 seats 34 automatic dimming 37 luggage compartment Continuously Variable windshield 65, 68 Interlock 42 lamps 105 CONTROLS automatic Transmission windshield washer jets 52 Interval display 93 parking lamps 49, 102 (CVT) 48 Heavy cargo 72 reading lamps 50 General driving notes 76 Height 121 J rear fog lamp 103 Glove compartment 70 High beams 17, 49 Jack 100, 106 standing lamps 49, 102 Glove compartment lamps bulb replacement 101 Jump-starting 113, 114 tail lamp 103 OPERATION bulb replacement 105 Hood 16, 86 turn signal indicators 102 Grilles 66, 69 Horn 12 K xenon lamps 101 Gross weight 122 Hubcap remover 100, 106 Keys 22 Lashing eyes 72 multifunction steering LATCH child-restraint H I wheel 18 system 41 Handbrake 44 Ignition lock 42 Kickdown 47 Leather care 95 Hazard warning flashers 12 Illuminated vanity mirror 36 LED light-emitting diodes 51 REPAIRS Head airbags 37 Imitation leather 95 Length 121 L Head restraints 34 Imprint 6 License plate lamp Lamps 49, 101 Headlamp cleaning Indicator lamps 15 bulb replacement 104 backup lamps 103 system 52, 89 Individual air distribution 69 Light-alloy wheels 94 brake lamp 103, 104 filling 89 INSPECTION 57 "Lights on" warning 49 daytime driving lamps 49 Headlamp flasher 49 Instrument cluster, see Display Loading 72 fog lamps 50 Headlamps elements 13 Load-securing devices 72 DATA footwell lamps 105 care 94, 101 Instrument lighting 50 Low beams 49 front fog lamps 102 cleaning 52 Instrument panel 12 bulb replacement 101 glove compartment 105 Interface socket Luggage compartment 72 high beams 101 for Onboard Diagnostics 96 content 122 instrument lighting 50 INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 131
    • EVERYTHING FROM A TO Z Luggage compartment MINI Maintenance System 93 Oil change intervals, see Service Power supply 12 V 70 cover 71 MINI manufacturer 6 and Warranty Booklet (US Power windows 28 Luggage compartment lamp MINI Mobility System 100 models)/Warranty and Pressure, tires 80, 109 bulb replacement 105 Mirrors 36 Service Guide Booklet Luggage rack Mobility System, see MINI (Canadian models) Q see Roof-mounted luggage Mobility System 100 Oil service 57 Quality Grading, tire 83 rack 73 Modifications, technical 96 Old batteries 111 Lumbar support 32 Multifunction steering wheel Onboard tool kit 100 R (MFL) 18 Opening Radiator 91 M Multifunction switch 49 from inside 26 Radio, see separate Owner's M+S tires 85 from outside 23 Manual Maintenance 57, 93 N Outside temperature Rain sensor 51 Maintenance System 93 Navigation system, see display 59 Reading lamps 50 Manual operation separate Owner's Rear backrest driver's door 25 Manual 14 P foldable 71 sliding/tilt sunroof 30 Non-smoker's equipment Package tray, see Luggage Rear fog lamp 50 tailgate 27 package, see Cigarette lighter compartment cover 71 bulb replacement 103 Manual transmission 45 socket 70 Park Distance Control (PDC) 63 Rear lamps 45, 103 Manufacturer 6 Nozzles 66, 69 Parking brake 16, 44 Rear window defroster Master key 22 Parking lamps 49 automatic climate initialization 22 O bulb replacement 102 control 68 MD player, see separate OBD interface socket 96 Parking lamps/Low beams 49 heating and climate Owner's Manual Odometer 55 Parking, vehicle 76 control 65 Mechanical key 22 Oil 89 PDC (Park Distance Control) 63 Rear window wiper 52 MFL (Multifunction steering additives 90 Plastic 95 replacing 100 wheel) 18 level 15 Pollen 66 Rearview mirror 36 Microfilter 66, 69 prescribed oils 90 Pollen filter 69 Recirculated-air mode Mini Disc player, see separate pressure 15 Power output 17, 120 air contitioner system 65 Owner's Manual automatic climate control 68 132 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • EVERYTHING FROM A TO Z OVERVIEW Recirculation of air 65, 68 S Spare key 22 Technical data 120 Reclining seat 31 Safety belts 16, 31, 35, 95 Spark plugs 124 Technical modifications 96 Refueling 77 adjusting 35 Speed 120 Temperature Remaining distance for Safety lock buttons 26 Speeds 85 automatic climate service 57 Safety tires 80, 84, 110 Split rear backrest 71 control 68 CONTROLS Remote control 23 winter tires 84, 85 Spray jets 52 heating and climate battery 22 Screwdriver 100 Standing lamps 49 control 65 battery changing 22 Seats 31 bulb replacement 102 tires 83 initialization 22 Securing cargo 72 Starting 42 Temperature display 59 Removing mist, Selector lever shiftlock 42, 46 problems 43, 113, 114, 115 engine coolant 56 OPERATION windows 66, 69 Service and Warranty Booklet with a discharged Temperature layering 66, 69 Removing window mist (US models)/Warranty and battery 113, 114 Temperatures, high 77 air conditioner system 66 Service Guide Booklet Steering lock 42 The right tires 84 automatic climate (Canadian models) 93 Storage, tires 84 Third brake lamp control 69 Service Interval Display 57, 93 Sun visors 36 bulb replacement 104 Replacement key 22 Shiftlock 46 Switches 12 Tire change Reporting safety defects 9 Side airbags 37 Switching off, engine 43 tire change set 106 REPAIRS Restraint system 38 Side turn signal indicators Symbols 6 Tire changes between axles 84 Reverse gear 45, 47 bulb replacement 102 Tire failure 16 Rod antenna 94 Sitting 31 T safety tires 110 Roller sun blind, rear window Sliding/tilt sunroof 29 Tachometer 55 space-saver spare tire 106 blind 30 convenience feature 25 Tail lamps Tire inflation pressure 80, 85 Rubber parts 95 safety function 30 bulb replacement 103 Tires 80 Run-flat tire, see Safety Smoker's equipment Tailgate 16, 27 all-season tires 85 DATA tires 80, 84, 85, 110 package 70 manual unlocking 27 break-in 76 Snow chains 85 Tank capacity 77 changing 106 Space-saver spare tire Tank content, filling condition 82, 85 changing tires 106 capacities 123 damage 82 INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 133
    • EVERYTHING FROM A TO Z inflation pressure 80 Tow-starting 115, 116 V Wheel and tire M+S tires 85 with Continuously Variable Vanity mirror 36 combinations 84 replacement 83 automatic Transmission bulb replacement 105 Wheel stud safety tires 80, 84, 85, 110 (CVT) 116 illuminated 36 wrench 100, 106, 107 snow chains 85 Tow-starting and towing 115 Vehicle Wheelbase 121 storage 84 Traction 83 battery 124 Width 121 temperature 83 Trailer nose weight 122 decommissioning 96 Windows, convenience the right choice 84 Transmission 45 dimensions 121 feature 25 tread 82 Transmission fault, exterior finish 94 Windshield heating winter tires 85 Continuously Variable operating 42 automatic climate with emergency running automatic Transmission settings 41 control 68 properties, see Safety (CVT) 48 washing 94 heating and climate tires 80, 84, 85, 110 Transporting children weight 122 control 65 Tools 100 safely 38 Vehicle Memory 41 Windshield washer Torque 120 Tread wear 83 Ventilation 66 system 51, 89 Tow bar 115 Trip odometer 55 draft-free 66, 69 filling 89 Tow fitting 115 Turn signal indicators 17, 49 Windshield wipers 51, 100 Tow socket for tow bulb replacement 102 W care 95 fittings 115 Warning lamp 15 replacing 100 Towing 115 U Warning triangle 113 Winter tires 85 with bar 115 Uniform Tire Quality Washer systems 89 all-season tires 85 with Continuously Variable Grading 83 Washer/wiper system 51 safety tires 84, 85 automatic Transmission Waste container 70 Wiper/washer system 51 (CVT) 116 Water on roadways Work in the engine Towing eyelets 115 deep water 77 compartment 86 Wearing safety belt 16, 35 Weights 122 134 Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • EVERYTHING FROM A TO Z OVERVIEW X Xenon lamps 101 CONTROLS OPERATION REPAIRS DATA INDEX Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG 135
    • REFUELING Fuel Designation AKI: Engine oil Quality The oil volume between the two marks on the dipstick corresponds to approx. 1.1 US quarts (1 liter). Tire inflation pressure Summer Winter To ensure that you always have convenient access to all essential information when you stop for fuel, front rear front rear we recommend that you take the time to fill out 2 persons the adjoining chart by entering the data that applies to your vehicle. 4 persons plus luggage Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • 01 41 0 156 724 ue DRIVE ME. Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG
    • MINI US-En Online Edition for Part No. 01 41 0 156 724 - © 01/02 BMW AG