Hoo Sze Yen                           Form 4 Experiments                 Physics SPM 2008CHAPTER 1:INTRODUCTION TO PHYSICS...
Hoo Sze Yen                             Form 4 Experiments                 Physics SPM 20082. With the thread taut and the...
Hoo Sze Yen                         Form 4 Experiments                      Physics SPM 2008CHAPTER 2:FORCES AND MOTION2.1...
Hoo Sze Yen                          Form 4 Experiments                       Physics SPM 2008Results:                    ...
Hoo Sze Yen                         Form 4 Experiments                    Physics SPM 20082.2 INERTIAOption 1: Using a saw...
Hoo Sze Yen                           Form 4 Experiments                      Physics SPM 2008Results:   Mass of          ...
Hoo Sze Yen                            Form 4 Experiments                     Physics SPM 2008Setup:Procedure:1. The inert...
Hoo Sze Yen                        Form 4 Experiments                     Physics SPM 20082.3 PRINCIPLE OF CONSERVATION OF...
Hoo Sze Yen                       Form 4 Experiments                      Physics SPM 2008Recording of data:mA mB         ...
Hoo Sze Yen                          Form 4 Experiments                     Physics SPM 2008Procedure:1. The apparatus is ...
Hoo Sze Yen                          Form 4 Experiments                      Physics SPM 2008Apparatus/Materials: Trolleys...
Hoo Sze Yen                          Form 4 Experiments                       Physics SPM 20082.4 FORCE, MASS AND ACCELERA...
Hoo Sze Yen                              Form 4 Experiments               Physics SPM 2008Results:Mass of trolley, m (kg) ...
Hoo Sze Yen                           Form 4 Experiments                      Physics SPM 2008Setup:Procedure:1. Apparatus...
Hoo Sze Yen                          Form 4 Experiments                      Physics SPM 20082.5 GRAVITATIONAL ACCELERATIO...
Hoo Sze Yen                          Form 4 Experiments                      Physics SPM 2008Results:              Mass of...
Hoo Sze Yen                          Form 4 Experiments                    Physics SPM 2008Setup:Procedure:1. Apparatus is...
Hoo Sze Yen                        Form 4 Experiments                    Physics SPM 20082.7 HOOKE’S LAWHypothesis:The big...
Hoo Sze Yen                         Form 4 Experiments                       Physics SPM 2008Results:Original length of sp...
Hoo Sze Yen                        Form 4 Experiments                    Physics SPM 2008CHAPTER 3:FORCES AND PRESSURE3.1 ...
Hoo Sze Yen                         Form 4 Experiments                      Physics SPM 2008Results:                      ...
Hoo Sze Yen                         Form 4 Experiments                      Physics SPM 2008Setup:Procedure:1. Apparatus i...
Hoo Sze Yen                         Form 4 Experiments                    Physics SPM 20083.2 ARCHIMEDES’ PRINCIPLEHypothe...
Hoo Sze Yen                         Form 4 Experiments                      Physics SPM 20084. The stone is lowered into t...
Hoo Sze Yen                          Form 4 Experiments                       Physics SPM 2008Apparatus and Materials: 5 m...
Hoo Sze Yen                        Form 4 Experiments                    Physics SPM 20083.4 BERNOULLI’S PRINCIPLEHypothes...
Hoo Sze Yen                         Form 4 Experiments                     Physics SPM 2008Venturi tube:                Wi...
Hoo Sze Yen                         Form 4 Experiments                    Physics SPM 2008CHAPTER 4:HEAT AND ENERGY4.1 SPE...
Hoo Sze Yen                        Form 4 Experiments                    Physics SPM 20086. The highest temperature the wa...
Hoo Sze Yen                         Form 4 Experiments                    Physics SPM 2008Apparatus and Materials: Beaker,...
Hoo Sze Yen                          Form 4 Experiments                      Physics SPM 2008Conclusion:When an object of ...
Hoo Sze Yen                         Form 4 Experiments                    Physics SPM 2008Results:Electric power of heater...
Hoo Sze Yen                          Form 4 Experiments                  Physics SPM 2008Set up:Procedure:1. The apparatus...
Hoo Sze Yen                         Form 4 Experiments                    Physics SPM 2008•   After the naphthalene has co...
Hoo Sze Yen                          Form 4 Experiments                  Physics SPM 2008Results:                 Time, t ...
Hoo Sze Yen                         Form 4 Experiments                    Physics SPM 2008Set up:                     Set ...
Hoo Sze Yen                           Form 4 Experiments                    Physics SPM 2008Discussion:• The purpose of Se...
Hoo Sze Yen                          Form 4 Experiments                   Physics SPM 2008Results:Electrical power of heat...
Hoo Sze Yen                          Form 4 Experiments                     Physics SPM 2008Set up:Procedure:1. Apparatus ...
Hoo Sze Yen                         Form 4 Experiments                    Physics SPM 2008Option 2: Changing the pressure ...
Hoo Sze Yen                          Form 4 Experiments                     Physics SPM 2008Results:       Pressure, P (kP...
Hoo Sze Yen                         Form 4 Experiments                     Physics SPM 2008Set up:Procedure:1. Apparatus i...
Hoo Sze Yen                         Form 4 Experiments                    Physics SPM 2008Discussion:From the graph plotte...
Hoo Sze Yen                         Form 4 Experiments                     Physics SPM 2008Procedure:1. Apparatus is set u...
Hoo Sze Yen                          Form 4 Experiments                     Physics SPM 2008CHAPTER 5:LIGHT AND VISION5.1 ...
Hoo Sze Yen                             Form 4 Experiments                Physics SPM 2008Results:                        ...
Hoo Sze Yen                        Form 4 Experiments                    Physics SPM 20085. The values of u, v, and the ch...
Hoo Sze Yen                            Form 4 Experiments                Physics SPM 2008Variables:Manipulated: Angle of i...
Hoo Sze Yen                         Form 4 Experiments                      Physics SPM 20085.4 ACTUAL DEPTH & APPARENT DE...
Hoo Sze Yen                         Form 4 Experiments                      Physics SPM 2008Results:                      ...
Hoo Sze Yen                              Form 4 Experiments                   Physics SPM 20082. The glass block is put as...
Hoo Sze Yen                         Form 4 Experiments                     Physics SPM 2008Setup:Procedure:1. The apparatu...
Upcoming SlideShare
Loading in...5
×

F4 Experiments

60,174

Published on

Published in: Technology, Education
9 Comments
54 Likes
Statistics
Notes
No Downloads
Views
Total Views
60,174
On Slideshare
0
From Embeds
0
Number of Embeds
3
Actions
Shares
0
Downloads
2,506
Comments
9
Likes
54
Embeds 0
No embeds

No notes for slide

F4 Experiments

  1. 1. Hoo Sze Yen Form 4 Experiments Physics SPM 2008CHAPTER 1:INTRODUCTION TO PHYSICS1.1 PENDULUMHypothesis:The longer the length of a simple pendulum, the longer the period of oscillation.Aim of the experiment:To investigate how the period of a simple pendulum varies with its length.Variables:Manipulated: The length of the pendulum, lResponding: The period of the pendulum, TConstant: The mass of the pendulum bob, gravitational accelerationApparatus/Materials:Pendulum bob, length of thread about 100 cm long, retort stand, stopwatchSetup: Thread Length, l Retort stand PendulumProcedure:1. The thread is tied to the pendulum bob. The other end of the thread is tied around the arm of the retort stand so that it can swing freely. The length of the pendulum, l is measured to 80 cm as per the diagram.Chapter 1: Introduction to Physics Page 1 of 52
  2. 2. Hoo Sze Yen Form 4 Experiments Physics SPM 20082. With the thread taut and the bob at rest, the bob is lifted at a small amplitude (of not more than 10°). Ensure that the pendulum swings in a single plane.3. The time for ten complete oscillations of the pendulum is measured using the stopwatch.4. Step 3 is repeated, and the average of both readings are calculated.5. The period of oscillation, T is calculated using the average reading divided by the number of oscillations, i.e. 10.6. T2 is calculated by squaring the value of T.7. Steps 1 to 6 are repeated using l = 70 cm, 60 cm, 50 cm, and 40 cm.8. A graph T2 versus l is plotted.Recording of data: Length of Time of oscillations, t (s) Period of oscillation, Tpendulum, l t1 t2 Average T = t/10 (s) T2 (s2) (cm) 80 70 60 50 40Graph of T2 vs lT2 Length of pendulum, lDiscussion:The graph of T2 versus l shows a straight line passing through the origin. This means thatthe period of oscillation increases with the length of the pendulum, with T2 directlyproportional to l.Conclusion:The longer the length of the pendulum, the longer the period of oscillation. Thehypothesis is proven valid.Chapter 1: Introduction to Physics Page 2 of 52
  3. 3. Hoo Sze Yen Form 4 Experiments Physics SPM 2008CHAPTER 2:FORCES AND MOTION2.1 INCLINED PLANESHypothesis:The larger the angle of incline, the higher the velocity just before reaching the endof the runwayAim of the experiment:To study the relationship between the velocity of motion and the angle of inclinationVariables:Manipulated: Angle of inclineResponding: Velocity just before reaching the end of the runwayConstant: Length of runwayApparatus/Materials: Trolley, protractor, wooden blocks, cellophane tape, ticker-timer, ticker tape, power supply, friction-compensated runwaySetup:Procedure:1. The apparatus is set up as per the diagram, and the inclined angle of the plane is measured using a protractor. An initial angle of 5° is used.2. The ticker-timer is started up and at the same time the trolley is released to slide down the plane.3. The final velocity when the trolley reaches the end of the plane is calculated using the distance of 10 ticks on the ticker tape.4. The procedure is repeated by changing the angle of incline to 10°, 15°, 20° and 25°.Chapter 2: Forces and Motion Page 3 of 52
  4. 4. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results: Angle of incline (˚) Final velocity (m s-1) 5 10 15 20 25Analysis:A graph of the velocity of the trolley against the angle of incline is plotted as follows:Velocity (m s-1) Angle of incline (°)Conclusion:A higher angle of incline will have a higher velocity at the end of the runway.Hypothesis accepted.Note: The experiment can be modified by making the angle constant and varying theheight and length of the runway. Changes must be made accordingly: hypothesis,variable list, procedure, table, analysis, conclusion.Chapter 2: Forces and Motion Page 4 of 52
  5. 5. Hoo Sze Yen Form 4 Experiments Physics SPM 20082.2 INERTIAOption 1: Using a saw bladeHypothesis:The larger the mass, the larger the inertiaAim of the experiment:To study the effect of mass on the inertia of an objectVariables:Manipulated: Mass, mResponding: Period of oscillation, TConstant: Stiffness of blade, distance of the centre of the plasticine from the clampApparatus/Materials: Jigsaw blade, G-clamp, stopwatch, and plasticine spheres ofmass 20 g, 40 g, 60 g, 80 g, and 100 gSetup:Procedure:1. One end of the jigsaw blade is clamped to the leg of a table with a G-clamp as per the diagram drawn.2. A 20 g plasticine ball is fixed at the free end of the blade.3. The free end of the blade is displaced horizontally and released so that it oscillates. The time for 10 complete oscillations is measured using a stopwatch. This step is repeated. The average of 10 oscillations is calculated. Then, the period of oscillation is determined.4. Steps 2 and 3 are repeated using plasticine balls with masses 40 g, 60 g, 80 g, and 100 g.5. A graph of T2 versus mass of load, m is drawn.Chapter 2: Forces and Motion Page 5 of 52
  6. 6. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results: Mass of Time of oscillations, t (s) Period of oscillation, T load, m (g) t1 t2 Average T = t/10 (s) T2 (s2) 20 40 60 80 100Graph of T2 versus m:Discussion:The graph of T2 versus m shows a straight line passing through the origin. This meansthat the period of oscillation increases with the mass of the load; that is, an object with alarge mass has a large inertia.Conclusion:Objects with a large mass have a large inertia. This is the reason why it is difficult to setan object of large mass in motion or to stop it. The hypothesis is valid.Option 2: Using an inertia balanceHypothesis:The larger the mass, the bigger the inertiaAim of the experiment:To study the effect of mass on the inertia of an objectVariables:Manipulated: Mass, mResponding: Period of oscillation, TConstant: Stiffness of the inertia balanceApparatus/Materials: Inertia balance, masses for the inertia balance, G-clamp,stopwatchChapter 2: Forces and Motion Page 6 of 52
  7. 7. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Setup:Procedure:1. The inertia balance is set up by clamping it onto one end of the table as shown in the figure above.2. One mass is placed into the inertia balance. The inertia balance is displaced to one side so that it oscillates in a horizontal plane.3. The time for 10 complete oscillations is measured using a stopwatch. This step is repeated. The average of 10 oscillations is calculated. Then, the period of oscillation is determined.4. Steps 2 and 3 are repeated using two and three masses on the inertia balance.5. A graph of T2 versus number of masses, n is drawn.Results:Number of Time of oscillations, t (s) Period of oscillation, T masses, n t1 t2 Average T = t/10 (s) T2 (s2) 1 2 3Graph of T2 versus m:Discussion:The graph of T2 versus m shows a straight line passing through the origin. This meansthat the period of oscillation increases with the mass of the load; that is, an object with alarge mass has a large inertia.Conclusion:Objects with a large mass have a large inertia. This is the reason why it is difficult to setan object of large mass in motion or to stop it. The hypothesis is valid.Chapter 2: Forces and Motion Page 7 of 52
  8. 8. Hoo Sze Yen Form 4 Experiments Physics SPM 20082.3 PRINCIPLE OF CONSERVATION OF MOMENTUMExperiment 1: Elastic collisionsHypothesis:The total momentum before collision is equal to the total momentum after collision,provided there are no external forces acting on the systemAim of the experiment:To demonstrate conservation of momentum for two trolleys colliding with eachother elasticallyVariables:Manipulated: Mass of trolleysResponding: Final velocities of the trolleys / Momentum of the trolleysConstant: Surface of ramp usedApparatus/Materials: Friction-compensated runway, ticker-timer, A.C. power supply,trolleys, wooden block, ticker tape, cellophane tapeSetup:Procedure:1. The apparatus is set up as shown in the diagram.2. The runway is adjusted so that it is friction-compensated.3. Two trolleys of equal mass are selected. A spring-loaded piston is fixed to the front end of trolley A.4. Two pieces of ticker tape are attached to trolleys A and B respectively with cellophane tape. The ticker tapes are separately passed through the same ticker-timer.5. The ticker-timer is switched on and trolley A is given a slight push so that it moves down the runway at uniform velocity and collides with trolley B which is stationary.6. The ticker-timer is switched off when both trolleys reach the end of the runway.7. From the ticker tapes of trolleys A and B, the final velocities are determined.8. Momentum is calculated using the formula p = mv.9. The experiment is repeated using different masses of trolleys.Chapter 2: Forces and Motion Page 8 of 52
  9. 9. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Recording of data:mA mB Before collision After collision uA Initial total momentum, vA vB Final total momentum, mAuA mAvA + mBvB m m m 2m2m m2m 2mAnalysis:From the above table, it is found that: Total momentum before collision = Total momentum after collisionConclusion:Hypothesis proven.Experiment 2: Inelastic collisionsHypothesis:The total momentum before collision is equal to the total momentum after collision,provided there are no external forces acting on the systemAim of the experiment:To demonstrate conservation of momentum for two trolleys colliding with eachother inelasticallyVariables:Manipulated: Mass of trolleysResponding: Final velocities of the trolleys / Momentum of the trolleysConstant: Surface of ramp usedApparatus/Materials: Friction-compensated runway, ticker-timer, A.C. power supply,trolleys, wooden block, ticker tape, cellophane tape, plasticine / VelcroSetup:Chapter 2: Forces and Motion Page 9 of 52
  10. 10. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Procedure:1. The apparatus is set up as shown in the diagram.2. The runway is adjusted so that it is friction-compensated.3. Two trolleys of equal mass are selected. Plasticine is fixed to the front end of trolley A. (Alternatively, use Velcro pads)4. A ticker tape is attached to trolley A with cellophane tape. The ticker tape is passed through the ticker-timer.5. The ticker-timer is switched on and trolley A is given a slight push so that it moves down the runway at uniform velocity and collides with trolley B which is stationary.6. The ticker-timer is switched off when both trolleys reach the end of the runway.7. The final velocity is determined from the ticker tape.8. Momentum is calculated using the formula p = mv.9. The experiment is repeated using different masses of trolleys.Results:mA mB Before collision After collision u Initial total momentum, v Final total momentum, mAuA (mA + mB) v m m m 2m2m m2m 2mAnalysis:From the above table, it is found that: Total momentum before collision = Total momentum after collisionConclusion:Hypothesis proven.Experiment 3: ExplosionHypothesis:The total momentum before collision is equal to the total momentum after collision,provided there are no external forces acting on the systemAim of the experiment:To demonstrate conservation of momentum for two trolleys moving away from eachother from an initial stationary positionVariables:Manipulated: Mass of trolleysResponding: Final velocities of the trolleys / Momentum of the trolleysConstant: Surface usedChapter 2: Forces and Motion Page 10 of 52
  11. 11. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Apparatus/Materials: Trolleys, wooden blocks, ticker tape, cellophane tapeSetup: Before explosion After explosionProcedure:1. The apparatus is set up as shown in the diagram.2. Two trolleys A and B of equal mass are placed in contact with each other on an even and smooth surface. Two wooden blocks are placed on the same row at the end of each trolley respectively.3. The vertical trigger on trolley B is given a light tap to release the spring-loaded piston which then pushes the trolleys apart. The trolleys collide with the wooden blocks.4. The positions of the wooden blocks are adjusted so that both the trolleys collide with them at the same time.5. The distances, dA and dB are measured and recorded.6. The experiment is repeated with different masses of trolleys.Results: Before After explosion explosion Initial total Mass of Mass of Distance Distance Final total momentum trolley trolley traveled by traveled by momentum, A, mA B, mB trolley A, dA trolley B, dB mAdA + mB(-dB) 0 m m 0 m 2m 0 2m m 0 2m 2mAnalysis:Because both trolleys hit the wooden blocks at the same time, the velocity of the trolleyscan be represented by the distance traveled by the trolleys.From the above table, it is found that: Initial total momentum = 0 Final total momentum = 0 ∴ Total momentum before collision = Total momentum after collisionConclusion:Hypothesis proven.Chapter 2: Forces and Motion Page 11 of 52
  12. 12. Hoo Sze Yen Form 4 Experiments Physics SPM 20082.4 FORCE, MASS AND ACCELERATIONExperiment 1: Relationship between acceleration and masswhen force is constantHypothesis:When the force applied is constant, the acceleration of an object decreases when itsmass increasesAim of the experiment:To study the effect of mass of an object on its acceleration if the applied force isconstantVariables:Manipulated: Mass, mResponding: Acceleration, aConstant: Applied force, FApparatus/Materials: Ticker-timer, A.C. power supply, trolleys, elastic band, runway,wooden block, ticker tape, cellophane tapeSetup:Procedure:1. Apparatus is set up as shown in the diagram.2. A ticker-tape is attached to the trolley and passed through the ticker-timer.3. The ticker-timer is switched on and the trolley is pulled down the inclined runway with an elastic band attached to the hind post of the trolley.4. The elastic band must be stretched to a fix length that is maintained throughout the motion down the runway.5. When the trolley reaches the end of the runway, the ticker-timer is switched off and the ticker tape is removed.6. Starting from a clearly printed dot, the ticker tape is divided into strips with each strip containing 10 ticks.7. A ticker tape chart is constructed, and from the chart, the acceleration of the trolley is calculated.8. The experiment is repeated using 2 and 3 trolleys. The elastic band must be stretched to the same fixed length as in step 4.Chapter 2: Forces and Motion Page 12 of 52
  13. 13. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results:Mass of trolley, m (kg) 1 Acceleration, a (m s-2) m1 trolley2 trolleys3 trolleysAnalysis: 1A graph of a against is drawn. ma 1 m 1From the graph, it shows that aα mConclusion:The acceleration of an object decreases when the mass increases. Hypothesis proven.Experiment 2: Relationship between acceleration and forcewhen mass is constantHypothesis:When the mass is constant, the acceleration of an object increases when the appliedforce increasesAim of the experiment:To study the effect of force on an object’s acceleration if its mass is constantVariables:Manipulated: Applied force, FResponding: Acceleration, aConstant: Mass, mApparatus/Materials: Ticker-timer, A.C. power supply, trolleys, elastic band, runway,wooden block, ticker tape, cellophane tapeChapter 2: Forces and Motion Page 13 of 52
  14. 14. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Setup:Procedure:1. Apparatus is set up as shown in the diagram.2. A ticker-tape is attached to the trolley and passed through the ticker-timer.3. The ticker-timer is switched on and the trolley is pulled down the inclined runway with an elastic band attached to the hind post of the trolley.4. The elastic band must be stretched to a fix length that is maintained throughout the motion down the runway.5. When the trolley reaches the end of the runway, the ticker-timer is switched off and the ticker tape is removed.6. Starting from a clearly printed dot, the ticker tape is divided into strips with each strip containing 10 ticks.7. A ticker tape chart is constructed, and from the chart, the acceleration of the trolley is calculated.8. The experiment is repeated using 2 and 3 elastic bands. The elastic bands must be stretched to the same fixed length as in step 4.Results: Force applied, F Acceleration, a (m s-2) 1 unit 2 units 3 unitsAnalysis:A graph of a against F is drawn.a FFrom the graph, it shows that a α FConclusion:The acceleration of an object increases when the applied force increases. Hypothesisproven.Chapter 2: Forces and Motion Page 14 of 52
  15. 15. Hoo Sze Yen Form 4 Experiments Physics SPM 20082.5 GRAVITATIONAL ACCELERATIONHypothesis:Gravitational acceleration does not depend on an object’s massAim of the experiment:To measure the acceleration due to gravityVariables:Manipulated: Mass, mResponding: Gravitational acceleration, gApparatus/Materials: Ticker-timer, ticker tape, A.C. power supply, retort stand,weights (50 g – 250 g), G-clamp, cellophane tape, soft boardSetup:Procedure:1. Apparatus is setup as shown in the diagram above.2. One end of the ticker tape is attached to a 50 g weight with cellophane tape, and the other end is passed through the ticker timer.3. The ticker-timer is switched on and the weight is released so that it falls onto the soft board.4. The ticker-timer is switched off when the weight lands on the soft board.5. Gravitational acceleration is calculated from the middle portion of the ticker tape.6. The experiment is repeated with weights of mass 100 g, 150 g, 200 g, and 250 g.Chapter 2: Forces and Motion Page 15 of 52
  16. 16. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results: Mass of weights (g) Free fall acceleration (m s-2) 50 100 150 200 250Analysis:From the table above, it is found that the gravitational acceleration for all the weights ofdifferent masses are the same.Discussion:• The value of the gravitational acceleration, g obtained is less than the standard value of 9.81 m s-2• This is because the weight is not falling freely. It is affected by: o Air resistance o Friction between ticker tape and ticker-timerConclusionGravitational acceleration is not dependent on the mass of the object. Hypothesis proven.2.6 PRINCIPLE OF CONSERVATION OF ENERGYHypothesis:Energy cannot be created or destroyed, it can only change form.Aim of the experiment:To investigate the conversion of gravitational potential energy to kinetic energy.Variables:Manipulated: Mass, mResponding: Final velocity, vConstant: Height, hApparatus/Materials: Ticker-timer, ticker tape, A.C. power supply, trolley, thread,weights, smooth pulley, friction-compensated runway, soft board, cellophane tapeChapter 2: Forces and Motion Page 16 of 52
  17. 17. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Setup:Procedure:1. Apparatus is setup as shown in the diagram above.2. One end of the ticker tape is attached to the back of the trolley with cellophane tape and the other end is passed through the ticker-timer.3. The ticker-timer is switched on, and the trolley is released.4. The final velocity of the trolley and the weight is determined from the ticker tape obtained.5. The experiment is repeated with different masses of trolleys and weights.Results:Mass of trolley = M kgMass of weight = m kgHeight of weight before release = h mFinal velocity of trolley and weight = v m s-1Loss of potential energy of the weight = mghFinal kinetic energy of the trolley and the weight = ½ (M + m) v2It is found that ½ (M + m) v2 = mghConclusionThe loss of potential energy is converted to kinetic energy. Hypothesis proven.Note: The experiment can be modified by making the mass constant and changing theheight of the weight’s release. Changes must be made to the variables list and to thelast step of the procedure.Chapter 2: Forces and Motion Page 17 of 52
  18. 18. Hoo Sze Yen Form 4 Experiments Physics SPM 20082.7 HOOKE’S LAWHypothesis:The bigger the weight, the longer the spring extensionAim of the experiment:To determine the relationship between the weight and the spring extensionVariables:Manipulated: Weight of the loadResponding: Spring extensionConstant: Spring constantApparatus and Materials: Spring, pin, weights, plasticine, retort stand, metre ruleSetup:Procedure:1. The apparatus is setup as shown in the diagram.2. The length of the spring without any weights, l0 is measured using the metre rule with the pin as reference.3. A 50 g weight is hung from the bottom of the spring. The new length of the spring, l is measured. The spring extension is l – l0.4. Step 4 is repeated with weights 100 g, 150 g, 200 g, and 250 g.Chapter 2: Forces and Motion Page 18 of 52
  19. 19. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results:Original length of spring = l0 = __________ cm Load mass Load weight Spring length, l Spring extension, x = l – l0 (g) (N) (cm) (cm) 50 g 0.5 N 100 g 1.0 N 150 g 1.5 N 200 g 2.0 N 250 g 2.5 NAnalysis:A graph of spring extension, x against weight, F is plotted.x FThe x-F graph is a linear graph which passes through the origin. This shows that theextension of the spring is directly proportional to the stretching force.Conclusion:Hypothesis proven.Chapter 2: Forces and Motion Page 19 of 52
  20. 20. Hoo Sze Yen Form 4 Experiments Physics SPM 2008CHAPTER 3:FORCES AND PRESSURE3.1 PRESSURE IN LIQUIDSExperiment 1: Water pressure and depthHypothesis:Water pressure increases with depthAim of the experiment:To find the relationship between the pressure in a liquid according to its depthVariables:Manipulated: Depth of liquidResponding: Pressure in liquidConstant: Density of liquidApparatus and Materials: Measuring cylinder, thistle funnel, rubber tube,manometer, metre ruleSetup:Procedure:1. Apparatus is set up as shown in the diagram.2. The measuring cylinder is completely filled with water.3. The thistle funnel is lowered into the water to a depth of 10.0 cm. The manometer reading is measured. The difference in the liquid heights in the manometer represent the pressure reading.4. Step 3 is repeated with values of depth 20.0 cm, 30.0 cm, 40.0 cm and 50.0 cm.Chapter 3: Forces and Pressure Page 20 of 52
  21. 21. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results: Depth (cm) Manometer reading (cm) 10.0 20.0 30.0 40.0 50.0Analysis:A graph of pressure against depth is drawn.Pressure DepthConclusion:It is observed that the manometer reading increases as the depth of the thistle funnelincreases. This shows that the pressure increases with the depth of the liquid.Hypothesis proven.Experiment 2: Water pressure and densityHypothesis:Pressure in liquid increases with its densityAim of the experiment:To find the relationship between the pressure in a liquid and its densityVariables:Manipulated: Density of liquidResponding: Pressure in liquidConstant: Depth of liquidApparatus and Materials: Measuring cylinder, thistle funnel, rubber tube,manometer, metre rule, water, glycerin, alcoholChapter 3: Forces and Pressure Page 21 of 52
  22. 22. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Setup:Procedure:1. Apparatus is set up as shown in the diagram.2. The measuring cylinder is completely filled with water.3. The thistle funnel is lowered into the water to a depth of 50.0 cm. The manometer reading is measured. The difference in the liquid heights in the manometer represent the pressure reading.4. The experiment is repeated by replacing the water with glycerin (density = 1300 kg m-3) and alcohol (density = 800 kg m-3).Results:Depth within liquid = 50.0 cm Liquid Density (kg m-3) Manometer reading (cm) Water 1000 Glycerin 1300 Alcohol 800Conclusion:It is observed that the manometer reading increases as the density of the liquid increases.This shows that the pressure increases with the density of the liquid.Hypothesis proven.Chapter 3: Forces and Pressure Page 22 of 52
  23. 23. Hoo Sze Yen Form 4 Experiments Physics SPM 20083.2 ARCHIMEDES’ PRINCIPLEHypothesis:The buoyant force on an object in a liquid is equal to the weight of the liquiddisplacedAim of the experiment:To find the relationship between the buoyant force acting upon an object in a liquidand the weight of the liquid displacedVariables:Manipulated: Weight of the objectResponding: Buoyant force / Weight of liquid displacedConstant: Density of liquid usedApparatus and Materials: Eureka tin, spring balance, stone, thread, beaker, triplebeam balanceSetup:Procedure:1. A beaker is weighed with the triple beam balance and its mass, m1 is recorded.2. The Eureka tin is filled with water right up to the level of the overflow hole. The beaker is placed beneath the spout to catch any water that flows out.3. A stone is suspended from the spring balance with thread and its weight in air, W1 is read from the spring balance.Chapter 3: Forces and Pressure Page 23 of 52
  24. 24. Hoo Sze Yen Form 4 Experiments Physics SPM 20084. The stone is lowered into the Eureka tin until it is completely immersed in water without touching the bottom of the Eureka tin. The water will overflow into the beaker.5. The spring balance reading, W2 is recorded.6. The beaker with water is weighed with the triple beam balance, and the mass, m2 is recorded.Results:Weight of stone in air = W1Weight of stone in water = W2Buoyant force acting on the stone = W2 – W1Weight of the empty beaker = m1gWeight of the beaker and displaced water = m2gWeight of the displaced water = (m2 – m1)gIt is found that W2 – W1 = (m2 – m1)gDiscussion:The loss of weight of the stone immersed in water is due to the buoyant force of the wateracting upon it.From the results, it is found that the loss in weight of the stone is equal to the weight ofwater displaced.Conclusion:Buoyant force on the stone = Weight of the water displaced by the stoneHypothesis proven.Note: Experiment can be modified to compare the weight of different sized stones and thevalues of buoyant force3.3 PASCAL’S PRINCIPLEHypothesis:The liquid pressure exerted on a small surface is equal to the liquid pressure exertedon a large surface in a closed systemAim of the experiment:To find the relationship between the pressure in a small syringe and a large syringein a closed systemVariables:Manipulated: Pressure acting on the small syringeResponding: Pressure acting on the large syringeConstant: Density of liquid within the systemChapter 3: Forces and Pressure Page 24 of 52
  25. 25. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Apparatus and Materials: 5 ml syringe, 10 ml syringe, several weights, rubber tube,two retort standsSetup:Procedure:1. The diameters of the piston of both syringes are measured and their cross-sectional areas are calculated.2. The two syringes are each mounted on a retort stand.3. The syringes are filled with water and are securely connected to each other with a rubber tube as shown in the diagram.4. A weight is placed on the piston of the small syringe.5. Weights are added to the piston of the large syringe until the water levels in the two syringes are the same (i.e. syringes are in equilibrium).6. The forces, F1 and F2 on the syringes are calculated.7. The pressure, P1 and P2 exerted on the syringes are compared.Results: Syringe Cross-sectional Mass of the Force exerted on the Pressure, P size area, A weight, m syringe, F = mg F = A Small A1 m1 F1 P1 Large A2 m2 F2 P2Discussion:It is found that the pressure, P1 exerted on the piston of the small syringe is equal to thepressure, P2 exerted on the piston of the large syringe.Conclusion:The water pressure exerted on the piston of the small syringe is equal to the waterpressure exerted on the piston of the large syringe. This shows that the pressure applied tothe piston of the small syringe is transmitted to the piston of the large syringe.Hypothesis proven.Chapter 3: Forces and Pressure Page 25 of 52
  26. 26. Hoo Sze Yen Form 4 Experiments Physics SPM 20083.4 BERNOULLI’S PRINCIPLEHypothesis:When the velocity of water increases, its pressure decreases and vice versa.Aim of the experiment:To find the effects of movement on the pressure exerted by a fluidVariables:Manipulated: Velocity of the waterResponding: Pressure of the waterConstant: Density of the waterApparatus and Materials: Uniform glass tube, Venturi tube, rubber hose, water froma tapProcedure:1. A uniform glass tube is connected to a tap with a rubber hose. The other end of the tube is closed up with a stopper.2. The tap is opened slowly so that water flows into it.3. The levels of the vertical tubes are observed.4. The stopper is then removed. The tap is adjusted so that the water flows through the tube at a uniform rate.5. The levels of the vertical tubes are observed.6. The experiment is repeated by replacing the uniform glass tube with a Venturi tube.Results:Uniform glass tube: With the stopper Without the stopperChapter 3: Forces and Pressure Page 26 of 52
  27. 27. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Venturi tube: With the stopper Without the stopperDiscussion:• The height of the water in the vertical tube represents the pressure at that point.• When water is not flowing, the pressure along the entire tube is the same, therefore the water levels in all three vertical tubes are the same.• For the uniform glass tube: o Water flows from high pressure to low pressure. o Therefore, the water levels are decreasing because the pressure is decreasing.• For the Venturi tube: o The velocity at Y is higher because of the smaller cross-sectional area. o Therefore, the pressure at Y is the lowest. o Pressure still decreases from X to Z because water flows from high pressure to low pressure.Conclusion:The higher the water velocity, the lower the pressure at that point. Hypothesis proven.Chapter 3: Forces and Pressure Page 27 of 52
  28. 28. Hoo Sze Yen Form 4 Experiments Physics SPM 2008CHAPTER 4:HEAT AND ENERGY4.1 SPECIFIC HEAT CAPACITYExperiment 1: Rise in temperature – varying mass, fixed amountof heatHypothesis:The bigger the mass of water, the smaller the rise in temperature when suppliedwith the same amount of heatAim of the experiment:To determine the rise in temperature of water with varying massesVariables:Manipulated: Mass of water, mResponding: Rise in temperature, θConstant: Amount of heat supplied, QApparatus and Materials: Beaker, electric heater, thermometer, stopwatch, triplebeam balance, stirrer, polystyrene sheet, felt clothSet up:Procedure:1. With the help of a triple beam balance, fill a beaker with water of mass 0.40 kg.2. The apparatus is set up as shown in the diagram.3. The initial temperature of the water, θ1 is measured using a thermometer and is recorded.4. The electric heater is placed into the water and is switched on for 1 minute. The water is continuously stirred.5. The water is continuously stirred even after the heater has been switched off. TheChapter 4: Heat and Energy Page 28 of 52
  29. 29. Hoo Sze Yen Form 4 Experiments Physics SPM 20086. The highest temperature the water reaches, θ2 is measured and recorded. The rise in temperature, θ = θ2 – θ1 is calculated.7. The experiment is repeated with water of mass 0.50 kg, 0.60 kg, 0.70 kg, and 0.80 kg. 18. A graph of θ against m and a graph of θ against are plotted. mResults:Mass of water, Initial Final Rise in 1 m (kg) temperature, temperature, temperature, θ (kg-1) m θ1 (°C) θ2 (°C) = θ2 – θ1 (°C) 0.40 0.50 0.60 0.70 0.80Analysis:• The amount of heat supplied is made constant by using the same heater for the same period of time.• The following graphs are obtained:Conclusion:The rise in temperature is inversely proportional to the mass when a constant amount ofheat is supplied. Hypothesis proven.Experiment 2: Rise in temperature – fixed mass, varying amountof heatHypothesis:When more heat is supplied to water of fixed mass, the rise in temperature isgreaterAim of the experiment:To determine the rise in temperature of water with varying amounts of heatVariables:Manipulated: Amount of heat supplied, QResponding: Rise in temperature, θConstant: Mass of water, mChapter 4: Heat and Energy Page 29 of 52
  30. 30. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Apparatus and Materials: Beaker, electric heater, thermometer, stopwatch, triplebeam balance, stirrer, polystyrene sheet, felt clothSet up:Procedure:1. With the help of a triple beam balance, fill a beaker with water of mass 0.50 kg.2. The apparatus is set up as shown in the diagram.3. The initial temperature of the water, θ1 is measured using a thermometer and is recorded.4. The electric heater is placed into the water and is switched on for 1 minute. The water is continuously stirred.5. The water is continuously stirred even after the heater has been switched off.6. The highest temperature the water reaches, θ2 is measured and recorded. The rise in temperature, θ = θ2 – θ1 is calculated.7. The experiment is repeated with water of the same mass but with heating time of 2 minutes, 3 minutes, and 4 minutes.8. A graph of θ against t is plotted.Results: Heating time Initial Final Rise in (minute) temperature, temperature, temperature, θ θ1 (°C) θ2 (°C) = θ2 – θ1 (°C) 1 2 3 4Analysis:• Because the same heater with fixed power is used, the heating time, t is defined operationally as the heat quantity.• The following graph is obtained:Chapter 4: Heat and Energy Page 30 of 52
  31. 31. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Conclusion:When an object of fixed mass is heated, the rise in temperature changes proportionally tothe amount of heat supplied. Hypothesis proven.Experiment 3: Determining the specific heat capacity ofaluminiumAim of the experiment:To determine the specific heat capacity of aluminiumApparatus and Materials: Aluminium cylinder, weighing scale, electric heater,thermometer, power supply, felt cloth, polystyrene sheet, stopwatch, lubricating oilSet up:Procedure:1. An aluminium cylinder with two cavities is weighed and its mass, m is recorded.2. The electrical power of the heater, P is recorded.3. The electrical heater is then placed inside the large cavity in the centre of the cylinder.4. The thermometer is then placed in the small cavity of the aluminium cylinder.5. A few drops of lubricating oil are added to both cavities to ensure good thermal contact (better heat transfer).6. The apparatus is set up as shown in the diagram above.7. The initial temperature of the aluminium cylinder, θ1 is recorded.8. The electric heater is switched on and the stopwatch is started simultaneously.9. After heating for t seconds, the heater is switched off. The highest reading on the thermometer, θ2 is recorded.10. The experiment is repeated and an average value of c is calculated.Chapter 4: Heat and Energy Page 31 of 52
  32. 32. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results:Electric power of heater = P WattHeating time = t secondsMass of aluminium cylinder = m kgInitial temperature of the aluminium cylinder = θ1Final temperature of the aluminium cylinder = θ2Temperature rise = θ2 – θ1Electrical energy supplied by the heater = PtHeat energy absorbed by the aluminium cylinder = mcθOn the assumption that there is no heat loss to the surroundings: Heat supplied = Heat absorbed Pt = mcθ Pt Specific heat capacity, c = mθDiscussion:• The aluminium cylinder is wrapped with a felt cloth to reduce the heat loss to the surroundings and the polystyrene sheet acts as a heat insulator to avoid heat loss to the surface of the table.• The value of the specific heat capacity of aluminium, c determined in the experiment is larger than the standard value. This is because there will be some heat lost to the surrounding.• The temperature of the aluminium cylinder will continue to rise after the electrical heater has been switched off because there is still some heat transfer from the heater to the cylinder.Conclusion:The specific heat capacity of aluminium is a constant.4.2 SPECIFIC LATENT HEATExperiment 1: Heating of naphthaleneHypothesis:During the change of state of naphthalene from solid to liquid, there is no change intemperature when heat is continuously suppliedAim of the experiment:To observe the change in temperature when naphthalene is meltingApparatus and Materials: Boiling tube, naphthalene powder, beaker, thermometer,Bunsen burner, stopwatch, retort stand, tripod stand, wire gauzeChapter 4: Heat and Energy Page 32 of 52
  33. 33. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Set up:Procedure:1. The apparatus is set up as shown in the diagram.2. The initial temperature of the naphthalene is recorded.3. The Bunsen burner is lighted and the stopwatch started.4. The temperature of the naphthalene is recorded at 1 minute intervals until the temperature reaches 100°C.5. The state of the naphthalene is observed and tabulated throughout the heating process.6. A graph of temperature against time is drawn.Results: Time, t (minute) Temperature of naphthalene, θ (°C) 0 1 2 3 …Graph of temperature against time:Discussion:• The temperature-time graph shows that the temperature of naphthalene rises until the naphthalene starts to melt.• The naphthalene starts to melt at 80°C. The temperature remains constant at this value for several minutes while the naphthalene continues to melt with the heat.Chapter 4: Heat and Energy Page 33 of 52
  34. 34. Hoo Sze Yen Form 4 Experiments Physics SPM 2008• After the naphthalene has completely melted, the temperature begins to rise with continued heating.Conclusion:The temperature of the naphthalene remains constant during a change of state from solidto liquid.Experiment 2: Cooling of naphthaleneHypothesis:During the change of state of naphthalene from liquid to solid, there is no change intemperatureAim of the experiment:To observe the change in temperature when naphthalene is freezingApparatus and Materials: Boiling tube, naphthalene powder, beaker, thermometer,Bunsen burner, stopwatch, retort stand, tripod stand, wire gauzeSet up:Procedure:1. The apparatus is set up as shown in the diagram.2. The naphthalene is heated until the temperature reaches 95°C.3. The boiling tube is then removed from the water bath and the outer part of the tube is dried.4. The temperature of the naphthalene is recorded every minute until the temperature drops to about 60°C.5. A graph of temperature against time is drawn.Chapter 4: Heat and Energy Page 34 of 52
  35. 35. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results: Time, t (minute) Temperature of naphthalene, θ (°C) 0 1 2 3 …Graph of temperature against time:Discussion:• The temperature-time graph shows that the temperature of naphthalene drops until 80°C where it stays constant for several minutes as it freezes.• After the naphthalene has completely frozen, the temperature continues to drop.Conclusion:The temperature of the naphthalene remains constant during a change of state from liquidto solid.Experiment 3: Latent heat of fusion (ice)Aim of the experiment:To determine the latent heat of fusion of iceApparatus and Materials: Pure ice, electric immersion heater, filter funnel, beaker,stopwatch, weighing balance, power supply, retort stand, clampChapter 4: Heat and Energy Page 35 of 52
  36. 36. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Set up: Set A Set BProcedure:1. The mass of two empty beakers, A and B are determined using the weighing balance.2. The apparatus is arranged as shown in the diagram above.3. Each of the two filter funnels is filled with ice cubes.4. The immersion heater in Set A, the control experiment, is not connected to the power supply. The purpose of Set A is to determine the mass of the ice melted by the surrounding heat. The heater in Set B is switched on.5. When water starts to drip from the filter funnels at a steady rate, the stopwatch is started and the empty beakers A and B are placed beneath the filter funnels.6. After a period of t seconds, the heater B is switched off. The masses of both beakers, A and B are determined using the weighing balance.7. The experiment is repeated to get an average value.Results:Set A:Mass of empty beaker = mA1 kgMass of beaker + water = mA2 kgMass of ice melted by surrounding heat, ma = mA2 – mA1 kgSet B:Mass of empty beaker = mB1 kgMass of beaker + water = mB2 kgMass of ice melted by surrounding heat & immersion heater, mb = mB2 – mB1 kgMass of ice melted by the electric immersion heater, m = mb – ma kgElectrical energy supplied by the electrical immersion heater, E = PtHeat energy absorbed by the ice during melting, Q = mLAssuming there is no heat loss to the surroundings: Electrical energy supplied = Heat energy absorbed by the melting ice Pt = mL Pt Specific latent heat of fusion of ice, L = mChapter 4: Heat and Energy Page 36 of 52
  37. 37. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Discussion:• The purpose of Set A, the control experiment, is to determine the mass of ice melted by the surrounding heat.• The immersion heater must be fully immersed in the ice cubes to avoid or reduce heat loss.• The stopwatch is not started simultaneously when the immersion heater is switched on because the immersion heater requires a time period before reaching a steady temperature. At this point, the rate of melting of ice will be steady.• The value of the specific latent heat of fusion of ice, L obtained in this experiment is higher than the standard value because part of the heat supplied by the heater is lost to the surroundings.Conclusion:The specific latent heat of fusion of ice is a constant.Experiment 4: Latent heat of vapourisation (water)Aim of the experiment:To determine the latent heat of vapourisation of waterApparatus and Materials: Pure water, electric immersion heater, filter funnel, beaker,stopwatch, weighing balance, power supply, retort stand, clampSet up:Procedure:1. The apparatus is set up as shown in the diagram above.2. A beaker is placed on the platform of the electronic weighing balance.3. The electric heater is fully immersed in the water and held in this position by being clamped to a retort stand.4. The electric heater is switched on to heat the water to its boiling point.5. When the water starts to boil at a steady rate, the stopwatch is started and the reading on the electronic balance, m1 is recorded.6. The water is allowed to boil for a period of t seconds.7. At the end of the period of t seconds, the reading on the electronic balance, m2 is recorded.Chapter 4: Heat and Energy Page 37 of 52
  38. 38. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results:Electrical power of heater = P WattTime period of boiling = t secondsElectrical energy supplied by the electrical immersion heater, E = PtMass of water vapourised = m2 – m1Heat energy absorbed by the water during vapourisation, Q = mLAssuming there is no heat loss to the surroundings: Electrical energy supplied = Heat energy absorbed by the vapourized water Pt = mL PtSpecific latent heat of vapourization of water, L = mDiscussion:• The immersion heater must be fully immersed in the water to avoid or reduce heat loss.• The stopwatch is not started simultaneously when the immersion heater is switched on because the immersion heater requires a time period before reaching a steady temperature. At this point, the rate of heating of water will be steady.• The value of the specific latent heat of vapourization of water, L obtained in this experiment is higher than the standard value because part of the heat supplied by the heater is lost to the surroundings.Conclusion:The specific latent heat of vapourization of water is a constant.4.3 BOYLE’S LAWOption 1: Changing the volume of air to measure pressureHypothesis:When the volume of air decreases, the pressure increases when its mass andtemperature is constantAim:To investigate the relationship between the pressure and volume of airVariables:Manipulated: Volume of air within syringeResponding: Pressure of airConstant: Mass, temperature of airApparatus and Materials: Rubber hose, Bordon gauge, 100 cm3 syringeChapter 4: Heat and Energy Page 38 of 52
  39. 39. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Set up:Procedure:1. Apparatus is set up as per the diagram.2. The nose of the syringe is fitted with a rubber hose and the piston is adjusted so that air volume of 100 cm3 at atmospheric pressure is trapped in the syringe.3. The rubber hose is connected to a Bourdon gauge and air pressure is read from the gauge.4. The piston of the syringe is pushed in until the trapped air volume becomes 90 cm3 and the air pressure is read from the Bourdon gauge.5. Step 4 is repeated for air volume values 80, 70, and 60 cm3.Results: Volume, V (cm3) 1 Pressure, P (Pa) (cm-3) V 100 90 80 70 60Analysis: 1• A graph of P against is plotted. V• A linear graph going through the origin is obtained.• This indicates that pressure is inversely proportional to the volume of gas.Conclusion:Gas pressure of fixed mass is inversely proportional to itsvolume.Chapter 4: Heat and Energy Page 39 of 52
  40. 40. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Option 2: Changing the pressure of air to measure volumeHypothesis:When the pressure of air decreases, the volume increases when its mass andtemperature is constantAim:To investigate the relationship between the pressure and volume of airVariables:Manipulated: Pressure of airResponding: Volume of air trapped in the capillary tubeConstant: Mass, temperature of airApparatus and Materials: Bicycle pump, ruler, tank with oil, pressure gauge, glasstubeSet up:Procedure:1. The apparatus is set up as shown in the diagram above.2. The piston of the bicycle pump is pushed in to compress the air inside the glass tube until the pressure is 10 kPa.3. When the reading on the pressure gauge is P, the volume of the air column, V is recorded.4. Steps 1 and 2 are repeated for 5 pressure readings of 20 kPa, 30 kPa and 40 kPa.Chapter 4: Heat and Energy Page 40 of 52
  41. 41. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results: Pressure, P (kPa) 1 Volume, V (cm3) (Pa-1) P 10 20 30 40Analysis: 1• A graph of V against is plotted. P• A linear graph going through the origin is obtained.• This indicates that pressure is inversely proportional to the volume of gas.Conclusion:Volume of gas of fixed mass is inversely proportional to its pressure.4.4 CHARLES’ LAWHypothesis:When the temperature of air increases, the volume increases if the mass andpressure is constantAim:To investigate the relationship between the volume and the temperature of gasVariables:Manipulated: Air temperatureResponding: Air volumeConstant: Mass and pressure of the trapped airApparatus and Materials: Capillary tube, tall beaker, thermometer, Bunsen burner,tripod, wire gauze, retort stand, mercury or concentrated sulphuric acid, stirrer,ruler, ice, rubber bandChapter 4: Heat and Energy Page 41 of 52
  42. 42. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Set up:Procedure:1. Apparatus is set up as per the diagram.2. The air to be studied is trapped in a capillary tube by concentrated sulphuric acid.3. The capillary tube is fitted to a ruler using two rubber bands and the bottom end of the air column is ensured to match the zero marking on the ruler.4. Water and ice is poured into the beaker until the whole air column is submerged. Water is then stirred until the temperature rises to 10 °C. The length of the air column and the temperature of the water are recorded.5. Water is heated slowly while being stirred continuously. The length of the air column is recorded every 10 °C until the water temperature reaches 90 °C.Results:Temperature, θ (°C) 10 20 30 40 50 60 70 80 90Length of air column, x (cm)Analysis:• A graph of x against θ is plotted.• A linear graph is obtained.• When extrapolated, length x = 0 occurs when gas temperature, θ = -273 °C• When the Celsius scale is replaced with the Kelvin scale, a linear graph that goes through origin is obtained.Chapter 4: Heat and Energy Page 42 of 52
  43. 43. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Discussion:From the graph plotted, it is found that the length of the air column, x is directlyproportional to its temperature, T (K). Because gas volume is directly proportional to thelength of the column, it also indicates that gas volume is directly proportional to itsabsolute temperature.Conclusion:Gas volume of fixed mass is directly proportional to its absolute temperature4.5 PRESSURE LAWHypothesis:When the temperature of air increases, the pressure increases if the mass andvolume is constantAim:To investigate the relationship between the pressure and the temperature of gasVariables:Manipulated: Air temperatureResponding: Air pressureConstant: Mass and volume of the trapped airApparatus and Materials: Round-bottomed flask, mercury thermometer, Bourdongauge, Bunsen burner, tripod, wire gauze, retort stand, stirrer, iceSet up:Chapter 4: Heat and Energy Page 43 of 52
  44. 44. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Procedure:1. Apparatus is set up as per the diagram.2. The round-bottomed flask is submerged in water and the water bath with ice is stirred continuously until the temperature of the water bath is stable.3. The temperature of the water is taken from the thermometer.4. The reading from the Bourdon gauge is read at temperatures 30, 40, 50, 60, 70 and 80 °C.Results:Temperature, θ (°C) 30 40 50 60 70 80Air pressure, P (Pa)Analysis:• A graph of P against θ is plotted.• A linear graph is obtained.• When extrapolated, pressure P = 0 occurs when gas temperature, θ = -273 °C• When the Celsius scale is replaced with the Kelvin scale, a linear graph that goes through origin is obtained.Conclusion:Gas pressure of fixed mass is directly proportional to its absolute temperatureChapter 4: Heat and Energy Page 44 of 52
  45. 45. Hoo Sze Yen Form 4 Experiments Physics SPM 2008CHAPTER 5:LIGHT AND VISION5.1 REFLECTIONHypothesis:The angle of reflection is equal to the angle of incidenceAim of the experiment:To study the relationship between the angle of incidence and angle of reflectionVariables:Manipulated: Angle of incidence, iResponding: Angle of reflection, rConstant: Plane mirror usedApparatus/Materials: Light box, plane mirror, plasticine, paper, pencil, protractorSetup:Procedure:9. A straight line, PQ is drawn on a sheet of white paper.10. The normal line, ON is drawn from a point at the centre of PQ.11. With the aid of a protractor, lines at angles of incidence 15°, 30°, 45°, 60° and 75° to the normal line, are drawn to its left.12. A plane mirror is erected along the line PQ. It is secured in this position with the aid of plasticine.13. A ray of light from the ray box is directed along the 15° line. Two positions are marked with a pencil on the line of the reflected ray.14. Step 5 is repeated for the other angles of incidence.15. The plane mirror is removed. The reflected rays are drawn by joining the respective marks.16. The angles of reflection corresponding with all the angle of incidence are measured. The results are tabulated.Chapter 5: Light and Vision Page 45 of 52
  46. 46. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results: Incident angle (˚) Reflected angle (˚) 15 30 45 60 75Conclusion:The angle of incidence is equal to the angle of reflection.5.2 CURVED MIRRORSAim of the experiment:To study the characteristics of images formed by curved mirrorsApparatus/Materials: Concave mirror, convex mirror, plasticine, light bulb mountedon a wooden block, metre rule, white screenSetup:Procedure:1. The apparatus is set up as shown in the diagram.2. The focal length, f and the radius of curvature, r of the concave mirror, as supplied, are recorded.3. The light bulb is positioned at a distance greater than the radius of curvature of the mirror, i.e. u > 2f. The white screen is moved between the concave mirror and the light bulb until an image is clearly focused on the screen. The image distance, v is measured by a metre rule and recorded.4. Step 3 is repeated with the light bulb positioned at C (u = 2f), between C and F (f < u < 2f), at F (u = f), and between F and P (u < f).Chapter 5: Light and Vision Page 46 of 52
  47. 47. Hoo Sze Yen Form 4 Experiments Physics SPM 20085. The values of u, v, and the characteristics of the images formed are recorded in a table.6. The experiment is repeated by replacing the concave mirror with a convex mirror.Results:Concave mirror;Position of Object Image Characteristics of image object distance, u distance, v Real / Upright / Diminished / (cm) (cm) Virtual Inverted Magnified / Same sizeBeyond C (u > 2f) At C (u = 2f)Between C and F(f < u < 2f) At F (u = f)Between F and P (u < 2f)Convex mirrors:For all positions, the image characteristics are: __________________________Conclusion:• For concave mirrors, images formed can be real or virtual, whereas for convex mirrors, only virtual images are formed.• The characteristics of images formed by the concave mirror depend on the position of the object.5.3 REFRACTIONHypothesis: sin iThe refracted light ray obeys Snell’s Law which states that the value of is a sin rconstant where i is the angle of incidence and r is the angle of refractionAim of the experiment:To study the relationship between the angle of incidence and angle of refractionChapter 5: Light and Vision Page 47 of 52
  48. 48. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Variables:Manipulated: Angle of incidence, iResponding: Angle of refraction, rConstant: Plane mirror usedApparatus/Materials: Ray box, glass block, paper, pencilSetup:Procedure:1. The outline of the glass block is traced on a sheet of white paper and labeled.2. The glass block is removed. Point O is marked on one side of the glass block. With a protractor, lines forming angles of incidence 20°, 30°, 40°, 50° and 60° are drawn and marked.3. The glass block is replaced on its outline on the paper.4. A ray of light from the ray box is directed along 20° line. The ray emerging on the other side of the block is drawn.5. Step 4 is repeated for the other angles of incidence.6. The glass slab is removed. The points of incidence and the corresponding points of emergence are joined. The respective angles of refraction are measured with a protractor. sin i7. The values of sin i, sin r, and are calculated. sin rResults: Angle of incidence, i (°) Angle of refraction, r (°) Sin i Sin r sin i n= sin r 20 30 40 50 60Conclusion: sin iIt is found that is a constant. Hypothesis valid. sin rChapter 5: Light and Vision Page 48 of 52
  49. 49. Hoo Sze Yen Form 4 Experiments Physics SPM 20085.4 ACTUAL DEPTH & APPARENT DEPTHHypothesis:The deeper the actual depth, the deeper the apparent depthAim of the experiment:To study the relationship between the actual depth and apparent depthVariables:Manipulated: Actual depth, DResponding: Apparent depth, dConstant: Refractive index of medium (water), nApparatus/Materials: Tall beaker, 2 pins, ruler, metre rule, retort standSetup:Procedure:1. Apparatus is set up as shown in the diagram.2. A pin is mounted on a movable clamp on a retort stand.3. Another pin is placed at the base of the tall beaker. Water is filled as the actual depth to D = 7.0 cm.4. The object pin O is observed from the top, and pin I is adjusted vertically until it appears to meet pin O. At this point, the position of pin I matches the apparent depth, d of pin O. The apparent depth is measured from the top of the water level to the position of pin I.5. Step 4 is repeated by changing the actual depth to 9.0 cm, 11.0 cm, 13.0 cm and 15.0 cm.6. The results are tabulated and a graph of D against d is plotted.Chapter 5: Light and Vision Page 49 of 52
  50. 50. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Results: Actual depth, D (cm) Apparent depth, d (cm) 7.0 9.0 11.0 13.0 15.0Analysis:A linear graph that goes through origin is obtained.D dDiscussion:• The gradient of the graph is equal to the index of refraction of water.Conclusion:Hypothesis is valid5.5 TOTAL INTERNAL REFLECTIONAim of the experiment:To determine the critical angle of glassApparatus/Materials: Semicircular glass block, ray box, protractor, white paper,pencilSetup:Procedure:1. A semicircular glass block is placed on a sheet of white paper. The outline of the glass block is traced onto the paper with a sharp pencil.Chapter 5: Light and Vision Page 50 of 52
  51. 51. Hoo Sze Yen Form 4 Experiments Physics SPM 20082. The glass block is put aside. A normal line, NN’ is drawn through the centre point, O on the diameter.3. The glass block is replaced on its outline.4. A narrow beam of light from the ray box is directed at point O at a small angle of incidence. The refracted and reflected rays are observed.5. The angle of incidence, i measured from the normal line is adjusted until the light ray is refracted along the length of the air-glass boundary. The point of entry of the light ray is marked and measured with a protractor. At this point, the incident angle is known as the critical angle, c.6. The angle of incidence is increased and the resultant rays are observed.7. The experiment is repeated by pointing the light ray through the other side of the semicircle.Results:• When i < c, part of the light ray is refracted to the air, and part of it will be reflected back within the glass block• When i = c, the light ray will be refracted along the length of the glass-air boundary• When i > c, no refraction occurs; all the light ray will be totally internally reflected within the glass blockAnalysis:The critical angle, c is a constant. 1Refractive index of glass, n = sin cConclusion: 1The refractive index of glass, n = sin c5.6 LENSESHypothesis:The image produced by a convex lens is virtual or real depending on the position ofthe object. The characteristics of an image produced by a concave lens is notaffected by the object distance.Variables:Manipulated: Object distance, uResponding: Image distance, vConstant: Focal length of lens, fApparatus/Materials: Cardboard with a cross-wire in triangular cut-out, light bulb,lens holder, convex lens, concave lens, white screenChapter 5: Light and Vision Page 51 of 52
  52. 52. Hoo Sze Yen Form 4 Experiments Physics SPM 2008Setup:Procedure:1. The apparatus is set up as shown in the diagram.2. The focal length, f of the convex lens supplied is recorded.3. The object (triangle with a cross-wire) is placed at a distance greater than 2f from the convex lens.4. The white screen is moved back and forth until a sharp image of the triangle is formed on the screen. The image distance, v is measured. The characteristics of the image are observed and recorded in a table.5. Step 3 is repeated wit the object distances, u = 2f, f < u < 2f, u = f, and u < f.6. For positions where the image cannot be formed on the screen, the screen is removed and the image is viewed through the lens from the other side of the lens.7. The experiment is repeated by replacing the convex lens with a concave lens.Results:Convex lens: Position Object Image Characteristics of image of object distance, u distance, v Real / Upright / Diminished / (cm) (cm) Virtual Inverted Magnified / Same size u > 2f u = 2f f < u < 2f u=f u < 2fConcave lens:For all positions, the image characteristics are: __________________________Conclusion:• For convex lenses, images formed can be real or virtual, whereas for concave lenses, only virtual images are formed.• The characteristics of images formed by the convex lens depend on the position of the object.Chapter 5: Light and Vision Page 52 of 52

×