Jacton Electromechanical Co.,Ltd http://www.screw-jack.com1JTP Series Miter Gearbox
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com2ContentsGeneral information -----------------------------------...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com3General InformationUsed in pairs spiral bevel gear unit to tran...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com4Bevel GearHigh purity rugged alloy steel 20CrMnTiH materialCarb...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com5JTP54 SpecificationsJTP90 SpecificationsJTP110 SpecificationsSp...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com6JTP140 SpecificationsJTP170 SpecificationsJTP210 Specifications
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com7JTP240 SpecificationsJTP280 Specifications
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com8Selection GuideJT – P – 90 – 1:1 – 1500R – 1500R – B – B31 2 3 ...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com9C: 3 way drive shafts, input shaft clockwise, output shaft cloc...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com10Load characteristics of each gearbox 50Nm, moderate load, work...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com11Model JTP54 DimensionsDimensions
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com12Model JTP90 Dimensions
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com13Model JTP110 Dimensions
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com14Model JTP140 Dimensions
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com15Model JTP170 Dimensions
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com16Model JTP210 Dimensions
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com17Model JTP240 Dimensions
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com18Model JTP280 Dimensions
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com19Hollow Shaft and Flange AdapterIf you need JTP series miter ge...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com20Application ExamplesJTP series miter gearbox is also widely ap...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com21Operation ManualPlease read this entire document prior to oper...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com22Approved Lubricants:For miter gearboxs operating in an ambient...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com23Frequently Asked QuestionsHow Do I Know Which Shaft Of Miter g...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com24Company HistoryIn 1997, Established Jacton Hardware Fabricatio...
Jacton Electromechanical Co.,Ltd http://www.screw-jack.com25Contact UsJacton Electromechanical Co.,Ltd1118, Taibao Busines...
Upcoming SlideShare
Loading in...5
×

right angle gearbox,right angle bevel gear drives,right angle bevel gear reducer,right angle miter gearbox,right angle bevel gear boxes manufacturer - screw-jack.com

570

Published on

right angle gearbox,right angle bevel gear drives,right angle bevel gear reducer,right angle miter gearbox,right angle bevel gear boxes features:
1. Right angle assembly pairs spiral bevel gears.
2. Used to transmit rotary motion, mechanical power and torque.
3. Milled cubic body sizes 54x54x54mm to 280x280x280mm.
4. High efficiency bevel gearbox, up to 98%.
5. Gear ratios 1:1, 1.5:1, 2:1, 3:1, 4:1, 5:1, customized special gear ratio.
6. Input power maximum 1.5Kw to 188Kw. Drive torque maximum 12N.m to 1299N.m. Input and output speed maximum 1500Rpm (high speed gearbox, contact Jacton engineers).
7. 11mm to 60mm diameter input and output shaft, 8 types shaft arrangements and direction of shaft rotating. Shafts can be rotated in both forward and reverse direction. Clockwise and counter-clockwise rotation direction are available.
8. Soild shaft, hollow shaft and motor flange adapter are available.
9. horizontal mounting, overhung mounting or wall mounting are available.
10. 2 way shaft gearbox, 3 way shaft gearbox, 4 way shaft gearbox are available.
11. low backlash 8 to 15 arcmin, quiet low noise less than 80dB under 1500rpm at 1 meter distance, low working temperature less than 50 degree centigrade.
12. application in printing press, plastic extruder, sewage auger, bonding equipment, metering auger, sewage agitator, newspaper conveyor, bottling equipment, material handling, web finishing, paper conveying, conveyor, cardboard box equipment, packaging, satellite dish antennas, gate valve actuators, food processing, robotics, rubber processing, wrapping machine, solar panel, commercial mower, street sweeper, dual steering, bulkhead door opener, scissor lift, vertical pump drive, sand spreader, residential mower, car wash curtain, snow blower, mining equipment, crane, agricultural, grain wagon, harvester, forage harvester, manure spreader, fertilizer spreader, business form press, feed screw drive, sewage conveyor, collating machinery, mixing equipment, conveyor drive, screw jack system, film processor and pottle packaging equipment. Whatever your goal is to blend, blow, bottle, crank, cut, convey or the task is to press, propel or raise, Jacton bevel gearbox is welcomed and ideal power transmission solution with all these industries.

Published in: Business, Technology
0 Comments
1 Like
Statistics
Notes
  • Be the first to comment

No Downloads
Views
Total Views
570
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
0
Comments
0
Likes
1
Embeds 0
No embeds

No notes for slide

right angle gearbox,right angle bevel gear drives,right angle bevel gear reducer,right angle miter gearbox,right angle bevel gear boxes manufacturer - screw-jack.com

  1. 1. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com1JTP Series Miter Gearbox
  2. 2. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com2ContentsGeneral information ------------------------------------------------------------------------------ 3Configurations ------------------------------------------------------------------------------------- 4Specifications1. JTP54, JTP90, JTP110 ------------------------------------------------------------------------------ 52. JTP140, JTP170, JTP210 --------------------------------------------------------------------------- 63. JTP240, JTP280-------------------------------------------------------------------------------------- 7Selection Guide1. Gearbox Brand---------------------------------------------------------------------------------------- 82. Gearbox Series --------------------------------------------------------------------------------------- 83. Frame No. --------------------------------------------------------------------------------------------- 84. Gear Ratio --------------------------------------------------------------------------------------------- 85. Input & Output RPM ---------------------------------------------------------------------------------- 86. Shaft Arrangements And Direction Of Shaft Rotating ---------------------------------------------- 8-97. Mounting Position --------------------------------------------------------------------------------------9Selection Examples-------------------------------------------------------------------------------- 10Dimensions1. Model JTP54 ----------------------------------------------------------------------------------------- 112. Model JTP90 ----------------------------------------------------------------------------------------- 123. Model JTP110 ---------------------------------------------------------------------------------------- 134. Model JTP140 ---------------------------------------------------------------------------------------- 145. Model JTP170 ---------------------------------------------------------------------------------------- 156. Model JTP210 ---------------------------------------------------------------------------------------- 167. Model JTP240 ---------------------------------------------------------------------------------------- 178. Model JTP280 ---------------------------------------------------------------------------------------- 18Hollow Shaft and Flange Adapter ------------------------------------------------------------ 19Application Examples ---------------------------------------------------------------------------- 20Operation Manual ---------------------------------------------------------------------------------- 21-22Frequently Asked Questions ------------------------------------------------------------------- 23Company History ----------------------------------------------------------------------------------- 24Contact Us -------------------------------------------------------------------------------------------- 25
  3. 3. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com3General InformationUsed in pairs spiral bevel gear unit to transmit rotary motion, mechanical power and torque where thedrive shafts are at 90 degree right angle to each other, transmission efficiency up to 98%. Design lifeis 10000 hours.Standard Gearbox* Cubic shape gearbox* 8 gearboxes models JTP54, JTP90, JTP110, JTP140, JTP170, JTP210, JTP240, JTP280* Universal mounting positions, can be easily mounted in any direction* Gear ratio 1:1, 1.5:1, 2:1, 3:1, 4:1, 5:1* Power rating from 0.3Kw to 188kW* Torque rating from 9.55Nm to 1299NmShaft Configurations* 2 way, 3 way and 4 way* Solid shaft or hollow shaft* Motor adapter to bolt an IEC motor* 10,000 hours lifespan for all gearbox sizes* Input speed up to 2000Rpm, customize maximum 3000Rpm* Breather or vents available for high speed requiredAdvantages* Gearbox with low backlash, normal less than 10 arc minutes* Quiet running, when 1500Rpm, at 1meter distance, noise level less than 80dB* Normal temperature, when 1500Rpm, temperature less than 50 deg. C* Lubricants prior to shipment* All miter gearboxes are factory tested prior to shipment* Detailed 2D CAD autocad drawing final confirmed before placing an order to us* Small order quantities is acceptable* Fast delivery time of standard models gearboxes, OEM & ODM are acceptable
  4. 4. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com4Bevel GearHigh purity rugged alloy steel 20CrMnTiH materialCarburizing process, case hardened and lapped in pairs for intersecting shaftsLow noise with grinded spiral teethHigh torque with milled teethHigh rigidity and wear risistancePinion Shaft and Output ShaftHardened and tempered alloy steel 40Cr materialHanging heavy load capacityWith key and keywayCustomized stainless steel, chromium coated or other corrosion resistance paintingCustomized spline shaft,shaft without key and keywayHousingHigh rigidity FC-25 cast ironCustomized stainless steel, aluminium, galvanic coating or other corrosion resistance paintingBearingHeavy duty tapered roller bearingCustomized reinforced bearings for higher radial and axial loadOil SealDouble lip oil sealPrevent gear oil leak and dustproofConfigurations
  5. 5. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com5JTP54 SpecificationsJTP90 SpecificationsJTP110 SpecificationsSpecifications
  6. 6. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com6JTP140 SpecificationsJTP170 SpecificationsJTP210 Specifications
  7. 7. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com7JTP240 SpecificationsJTP280 Specifications
  8. 8. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com8Selection GuideJT – P – 90 – 1:1 – 1500R – 1500R – B – B31 2 3 4 5 6 8 91. Gearbox BrandJT: “Jacton” brand miter gearbox2. Gearbox SeriesP: P series miter gearbox3. Frame No.Frame No. 54 90 110 140Gearbox Sizes 54x54x54mm 90x90x90mm 110x110x110mm 140x140x140mmFrame No. 170 210 240 280Gearbox Sizes 170x170x170mm 210x210x210mm 240x240x240mm 280x280x280mmBefore selecting gearbox frame no., please check corresponding model’s specifications4. Gear RatioFrame No. 54 90 110 140 170 210 240 2801:1 1:1 1:1 1:1 1:1 1:1 1:1 1:11.5:1 1.5:1 1.5:1 1.5:1 1.5:1 1.5:1 1.5:1 1.5:12:1 2:1 2:1 2:1 2:1 2:1 2:1 2:13:1 3:1 3:1 3:1 3:1 3:1 3:1 3:14:1 4:1 4:1 4:1 4:1 4:1 4:1Gear Ratio5:1 5:1 5:1 5:1 5:1 5:1 5:15 & 6. Input & Output RPMRatios 1:1 1.5:1 2:1 3:1 4:1 5:1input Rpm output Rpm output Rpm output Rpm output Rpm output Rpm output Rpm2000 2000 1333 1000 667 500 4001500 1500 1000 750 500 375 3001000 1000 667 500 333 250 200750 750 500 375 250 187.5 150500 500 333 250 167 125 100250 250 167 125 83 62.5 5050 50 33 25 17 12.5 107. Shaft Arrangements And Direction Of Shaft RotatingA: 2 way drive shafts, input shaft clockwise, output shaft anti-clockwiseB: 2 way drive shafts, input shaft clockwise, output shaft clockwiseE: 2 way drive shafts, input shaft clockwise, output shaft clockwiseF: 2 way drive shafts, input shaft clockwise, output shaft anti-clockwise
  9. 9. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com9C: 3 way drive shafts, input shaft clockwise, output shaft clockwiseD: 3 way drive shafts, input shaft clockwise, output shaft anti-clockwiseG: 3 way drive shafts, input shaft clockwise, one output shaft anti-clockwise, another shaft clockwiseH: 4 way drive shafts, input shaft clockwise, one output shaft anti-clockwise, in-line shaft clockwise8. Mounting PositionB3, B9: horizontal mounted positionV3, V9: overhung mounted positionB5, V5, B6, V6, B7, B8, V8: wall mounted position
  10. 10. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com10Load characteristics of each gearbox 50Nm, moderate load, working 8 hours/day continuously:i.e: driven machine factor f1=1.25, input speed=1000Rpm, ratio i=1:1Calculated with the following formula, the torque required by each gearbox isEach gearbox required torque=50 x 1.25=62.5NmNo.1 Gearbox:No.1 gearbox carries its own torque of 62.5Nm and at the same time transmit torques to No.2 andNo.3 gearboxes, so the total load is 62.5Nm+62.5Nm+62.5Nm=187.5NmCheck above 6thpage specifications, JTP170 gearbox is selectedNo.2 Gearbox:Besides its own torque, No.2 gearbox has to transmit torque to No.3 gearbox, so the total load is:62.5Nm+62.5Nm=125NmCheck above 6thpage specifications, JTP140 gearbox is selectedNo.3 Gearbox:As only load C exists, torque large than 62.5Nm is acceptable.Check above 5thpage specifications, JTP110 gearbox is selectedNotes:1. When i≠1, please make a choice of the input shaft. When pinion shaft acts as the input shaft, themachine is a gear reducer. When output shaft acts as the input shaft, it is an gear inceaser. Thepositions of the two shafts can not be changed once the mounting positions and dimensions arefixed.2. When several gearboxes are connected for output, load capacity of the line shafting should bechecked.Selection Examples
  11. 11. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com11Model JTP54 DimensionsDimensions
  12. 12. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com12Model JTP90 Dimensions
  13. 13. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com13Model JTP110 Dimensions
  14. 14. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com14Model JTP140 Dimensions
  15. 15. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com15Model JTP170 Dimensions
  16. 16. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com16Model JTP210 Dimensions
  17. 17. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com17Model JTP240 Dimensions
  18. 18. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com18Model JTP280 Dimensions
  19. 19. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com19Hollow Shaft and Flange AdapterIf you need JTP series miter gearbox with hollow input or output shaft, input or output flange adapter,please contact Jacton directly.
  20. 20. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com20Application ExamplesJTP series miter gearbox is also widely application in screw jack lift system, food processing,robotics, rubber processing, printing machine, wrapping machine, solar panel, commercial mower,street sweeper, dual steering, bulkhead door opener, scissor lift, vertical pump drive, sand spreader,residential mower, car wash curtain, snow blower, mining equipment, crane, agricultural, grainwagon, harvester, forage harvester, manure spreader and fertilizer spreader. Whatever your goal isto blend, blow, bottle, crank, cut, convey or the task is to press, propel or raise, JTP series mitergearbox is welcomed and ideal power transmission solution with all these industries.
  21. 21. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com21Operation ManualPlease read this entire document prior to operating the miter gearbox. Miter gearbox failure or injuryto operators may be caused by improper installation, operation or maintenance.InstallationMiter gearboxs must be mounted on a rigid, structurally sound baseplate. Ensure that miter gearboxmounting pads rest evenly on the baseplate. The use of shims may be required to avoid housingdistortion which could alter the gear mesh or cause premature bearing failure.The miter gearbox may be driven by direct coupling, flexible coupling, or V-belt drive. Couplersshould require only a light force to install. The driveline must be accurately aligned within theequipment manufacturers requirements to limit operating loads and minimize thrust loads on themiter gearbox shaft. V-belt drives must be mounted close to the housing to minimize excessiveoverhung loading which could result in early bearing or shaft failures. Sheaves must fit correctly. Atinstallation, a tight forced fit could move the shaft from its normal position and cause internal damage.A loose fit could induce excessive vibration during operation and cause shaft damage or breakage.WarningWhen mounting the miter gearbox, the buyer is responsible to properly determine the quality or gradeof fastener, thread engagement, load carrying capacity, and torque requirements.WarningThe buyer is responsible to provide protective shields over all external rotating parts, couplers, orshaft extensions mounted on or with the miter gearbox. Protective clothing must be worn wheninstalling or maintaining the miter gearbox and operating system.Initial operation should be carried out under no-load conditions. Before applying power to the mitergearbox installation, review the following:1. Check tightness of mounting bolts.2. Check for proper oil level in miter gearbox.3. Be certain that tools, debris, etc., are clear from rotating parts.4. Rotate shafts by hand. If they do not rotate freely, check for uneven mounting, couplingmisalignment or excessive belt tension.If all tests are satisfactory, make connections to shafts, ensure that all safety devices are in place,and begin operation.LubricationAll miter gearboxes are factory tested prior to shipment. They include the correct amount of oil unlessspecified by the customer to be shipped dry. Shaft bearings are splash lubricated and partiallysubmerged in oil when the miter gearbox is mounted horizontally. After installation, remove thedipstick and verify correct oil level. If no dipstick is provided, determine level by any appropriatemethod. In general, the oil level should be approximately half the depth of the miter gearbox (to theparting line) for horizontal mounting, or to the shaft centerlines, if mounted other than horizontally.CautionPrior to operation, make sure the miter gearbox contains the correct amount of oil. If under-filled orover-filled, damage to the miter gearbox or injury to personnel may result.
  22. 22. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com22Approved Lubricants:For miter gearboxs operating in an ambient temp of –20 Deg. C and +85 Deg. CJT15 - JT60 miter gearbox lubricant brand is VG220 (ISO viscosity class)JT72 – JT85 miter gearbox lubricant brand is VG320 (ISO viscosity class)When low speed less than 100Rpm, optional grease lubricantCautionDonot combine synthetic with non-synthetic oils in the miter gearbox.MaintenanceWarningDisconnect power prior to any maintenance and do not bypass or inactivate any safety or protectivedevice. Lock out and tag the power supply to prevent unexpected application of power.Routinely inspect mounting bolts, couplers,or other power transmitting devices to ensure all parts arefirmly anchored.Keep shafts and vent plugs (when included) clean to prevent foreign particles fromentering seals or housing. Inspect daily for any oil leaks and any unusual noises. Inspect weekly forend play in shafts. Inspect belt drive tension after the first ten hours of operation and periodicallythereafter.Check the oil level every 24 hours of operation. In the beginning to change the oil when the mitergearbox has been in service for two weeks or 100 ~ 200 hours. Routine oil change intervals will varyfor each particular installation depending on the severity of the environment. Normal changes shouldoccur half ~ 1year or 1000 ~ 2000 hours of operation. The longest life at continuous service will berealized when the oil temperature does not exceed +85 deg. C. For oil substitutions, or for high inputspeeds, contact Jacton engineers.WarningDonot change or add oil while the miter gearbox is running. Damage to the miter gearbox or injury topersonnel may result. The miter gearbox housing, oil, plugs, and associated components may reachhigh temperatures and cause severe burns. Use extreme care when servicing the miter gearbox.Trouble Shooting
  23. 23. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com23Frequently Asked QuestionsHow Do I Know Which Shaft Of Miter gearbox Is As Input Shaft?When using a 1:1 ratio gearbox ,it does not matter which shaft is used as the input shaft. Normally,X-shaft is input shaft, Y-shaft is output shaft. For other reduction gear ratios input shaft is same as 1:1ratio gearbox, but for increasing gear ratios input shaft, which is Y-shaft is input shaft, X-shaft isoutput shaft.Can I Use Miter gearbox As Speed Increaser?All miter gearbox can be used as speed increaser, by inputting on the output side of the gearbox,however it is important to check whether the miter gearbox can handle the power and speed. Whenusing as an increaser, the input speed does not exceed the specifications recommended maximumspeed. Special gearbox is available where the pinion can be put on the through shaft so that twooutput shaft increase the speed.Are Miter gearboxes Supplied Filled With Gear Oil?Yes, all miter gearboxes are filled gear oil prior to shipment, customers can install them and use themdirectly. Note: for low speed applications (100 rpm input speed and below) miter gearboxes may berecommended to have grease lubrication.How Often Should I Change Gear Oil In The Miter gearbox?Check the gear oil level every 24 hours of operation. In the beginning to change the gear oil when themiter gearbox has been in service for two weeks or 100 ~ 200 hours. Routine oil change intervals willvary for each particular installation depending on the severity of the environment. Normal changesshould occur half ~ 1year or 1000 ~ 2000 hours of operation. The longest life at continuous servicewill be realized when the oil temperature does not exceed +85 deg. C. For oil substitutions, or for highinput speeds, contact Jacton engineers.How Transmission Efficiency Of Miter gearbox?The miter gearbox transmission efficiency up to 98%
  24. 24. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com24Company HistoryIn 1997, Established Jacton Hardware Fabrication Plant, mainly processing kinds of hardwarefollowing customers requirements. Occupied 500 square meters.In 2000, Established domestic sales department, started to develop local market, mainly processinggear transmission parts such as worm and worm gear, acme threads screw, square threads screwand acme lead screw nut. Meanwhile, sales also sell straight bevel gear and spiral bevel gears forcustomers.In 2002, According to some regular customers of steel plants and machines manufacturers, whichused Taiwan screw jacks and miter gearboxes, due to long delivery and high price, would affect thenormal operations. Jacton Hardware Fabrication Plant started to processing JT acme screw jack andJT miter gearbox following above customers samples.In 2003, Established engineering department, research and development others models of JT acmescrew jack and JT miter gearbox, and draw some factory production drawings and local salescustomers drawing with 2d autocad software.In 2005, According to local market demands, Jacton Hardware Fabrication Plant is committed toresearch and development JB/T8809-1998 standard JTW worm screw jack, JTM machine screwjack, JTB ball screw jack and JTP cubic body miter gearbox.In 2006, Because of local markets fiercely competitive. Established Hongkong office-JactonInternational Limited with own US dollars and EURO account. Established international salesdepartment, focused on overseas markets. Meanwhile, "JACTON" as company only brand.In 2008, According to intl sales market report, cubic body screw jacks and another type cubic bodymiter gearboxes are very popular in Europe and America markets. After managements meetings, westarted to develop JTC cubic screw jack, JTS high speed bevel gear jack, JTV cubic body mitergearbox and JTA corrosion resistance aluminium body miter gearbox.In 2009, Jacton Hardware Fabrication Plant extension, occupied 5000 square meters. Companyimproves the processes and products through technology investment, brings in advancedtechnology, production and testing equipment.In 2010, Jacton Hardware Fabrication Plant Passed ISO9001:2008 quality management system, weare strictly implement the work flow of ISO9001:2008 certifications, which ensures oversea and localcustomers are satisfaction with our screw jacks and miter gearboxes and fast delivery time.In 2012, In order to facilitating management, according to management decisions, sales departmentand design department moved to Taibao business building. Meanwhile, Jacton Hardware FabricationPlant changed to be Dongguan Jacton Electromechanical Co.,Ltd.
  25. 25. Jacton Electromechanical Co.,Ltd http://www.screw-jack.com25Contact UsJacton Electromechanical Co.,Ltd1118, Taibao Business Building, No.1Langwei Rd, Xinan, Changan, Dongguan,Guangdong, ChinaPhone: 86 769 81585852Fax: 86 769 81585810Email: sales@screw-jack.comWebsite: www.screw-jack.comJacton International LimitedOffice 17,9/F.,Tower A,New MandarinPlaza,No.14,Science Museum Road,Tsimshatsui,Kowloon,HongkongTel: 852-2793-5511Fax: 852-3590-2333Website: www.screw-jack.com

×