Denture Duplicator Kit

674 views
531 views

Published on

A simple technique for making an in office, or lab processed, spare/duplicate denture.

Contact Lang Dental Manufacturing Co., Inc.:

Address: 175 Messner Drive
Wheeling, IL 60090
Phone: (800) 222-5264/(847) 215-6622
Fax: (847) 215-6678/(866) 278-8510
Site: http://www.langdental.com/
Twitter: https://twitter.com/#!/LangDental
Facebook: http://www.facebook.com/pages/Lang-Dental-Mfg-Co-Inc/178840485496822

Published in: Health & Medicine
0 Comments
1 Like
Statistics
Notes
  • Be the first to comment

No Downloads
Views
Total views
674
On SlideShare
0
From Embeds
0
Number of Embeds
5
Actions
Shares
0
Downloads
6
Comments
0
Likes
1
Embeds 0
No embeds

No notes for slide

Denture Duplicator Kit

  1. 1. Denture Duplicator FlaskPackage ContentsREF 0398 One FlaskIntended PurposeThis product is intended to create a duplicate denturefrom a patient’s original denture, or to create a surgi-cal guide/implant stent. denture duplicationOther Materials/Equipment NeededSilicone Spray Jet Seal, optionalAlginate SpatulaJet Acrylic Liquid Aquapres™/ pressure curingJet Tooth Shade Powder unit, optionalJet Denture Repair Powder Bur, pumice, lab polishJet Adjusters, optional Measuring cup • Spray insideflask flask with • Spray inside of of with silicone sprayfacilitate post silicone spray to to facilitate procedure clean-up. post procedure clean-up. • Fill half of flask with alginate. • Fill half of flask with alginate. • After alginate is set, trim excess
  2. 2. • Spray inside of flask with• silicone existingfacilitate post• Place spray to denture into Place existing denture into procedure clean-up. be be alginate. Teeth should alginate. Teeth should• perpendicular to thealginate. perpendicular to bottom Fill half of flask with the bottom of of the flask. the flask.• With wet fingers, smooth• With wet fingers, smooth alginate from borders of alginate from borders of denture to rim of flask, denture to rim of flask, removing excess alginate. removing excess alginate.• Spray inside of flask with• Place existing denture into silicone spray to facilitate post• alginate. Teethisshould be trim ex-• Afteralginate set, set, excess After alginate is trim• that coversclean-up. procedure Spray denture and surrounding Fill halfthat covers the denture. cess the denture.• perpendicularsiliconealginate. to the bottom alginate of flask with spray. with of the flask.• Fill other half of flask and• With wet fingers, smooth palate side of denture with alginate from borders of alginate.• denture tofingers, smooth With wet rim of flask, removing excess alginate. alginate to ensure complete coverage, working quickly before alginate sets.• After alginate is set, trim excess• Spray denture andand surrounding• Spray denture surrounding• alginate withthe denture. that covers Close flask with steady pressure. alginate with silicone spray. silicone spray.• Select appropriate Jet Tooth Shade Secure thumbof flask and allow screw and• powder. Fill half of flask and as• Fillother half Fill other teeth in impression alginate to set. palate side of denture Moisten palate side Liquid. with follows: Shake of denture with• alginate. Trim excess alginate. alginate.• Open wet fingers, smooth on surface with Jet liquid. Spray• With flask and remove denture.• With wetensure complete and alginate to fingers, smooth Jet powder. any gross defects in If there are Alternate liquid powder until teeth are complete alginate to ensure filled to the impression, make corrections coverage, working quickly gingival border.impression. now or retake When acrylic coverage, working quickly before alginate sets. appears dull, use small spatula to before alginate sets. push acrylic down to redefine gingival borders of all teeth.• Close flask with steady pressure.• Close flask with steady pressure.• Select appropriate Jet Tooth Shade• powder. Fill teeth screw and allow Cure for thumb in impression as Secure 15 minutes, either on Secure thumb screw and allow alginate to set.• Place 30ccto set.Denture Repair alginate of bench or, for Jet follows: Shakebest results, in Add• powder into alginate. Moisten Trim excess Liquid. cup.• Trim excess Jetalginate. on Aquapres at measuring surface with 30 remove denture. psi. (Curing Open Jet and liquid. Spray• 15cc of flask and remove denture.• Openflask liquid and mix forand Jetthere are any eliminates in under pressure 10 seconds. Alternate defects If powder. gross liquid porosity, are any gross defects in If there making a strong, dense,• powder until mixture into lower Pour 75% of teeth are filled to the impression, make corrections now impression, make corrections the or retake When acrylic aesthetically superior denture.) gingivalflask. Pour remaining half of border.impression. acrylicor retake impression.to now over use small• appears dull,palate on upper half With bur, trim teeth spatula interproximally. Place trimmed push acrylic down to redefine of flask. gingival borders impression. teeth back into of all teeth.
  3. 3. •• Select appropriate Jet Shade Select denture andJet Tooth Tooth Spray appropriate surrounding• alginate withteethsteady pressure. Close flask with in Fill teeth in powder. Fill siliconeimpression as Shade powder. spray. follows: Shake screw Moisten impression Liquid. Secure thumb as follows: Shake• Fill other half of flask and allow palate side ofJet liquid. with with Jet alginate with denture Spray on surface to set. Liquid. Moisten surface Trim excess Alternate liquid and Jet powder. alginate.• alginate. Spray on Jet powder. liquid.• With wet fingers, smooth to powder until teeth are filled• Open flask and remove powder until denture. Alternate liquid andacrylic alginate border. gross defects in gingival to ensure complete When If thereare filled teeth are any small spatula border. coverage, workingto gingival to appears dull, use quickly the impression, make corrections before alginate sets. redefine use When acrylic appears dull, push acrylic down to now or retake impression. gingival spatulaof all teeth. small borders to push acrylic down to redefine gingival borders of all teeth.• Select 30cc of Jet Denture Repair• Place appropriate Jet Tooth Shade• Cureforinto minutes, either onas powder 15 measuring cup. Add• powder. Fill15 minutes, either on Cure for teeth in impression follows: Jetfor best results,for in 15cc of Shake Liquid. mix in bench or, liquidbest Moisten bench or, for and results, 10 seconds. 30 liquid. Spray surface with Jet psi. (Curing on Aquapres at at 30 psi. (Curing Aquapres• Jet powder. Alternateinto lower under75% of mixture liquid and Pour pressure eliminates under pressure eliminates half of flask. Pour remaining to powder until teeth strong, dense, porosity, making a are filled gingival over palate on strong, dense, porosity, making a acrylic acrylic border. When upper half aesthetically superior denture.) appears dull, usesuperior denture.) aesthetically small spatula to of flask.• With bur, trim steady pressure,• push acrylicand teeth redefine• With slow trim teeth With bur, down to interproximally. Place trimmed close and secureof all teeth. flask. (Excess gingival borders impression. trimmed inter-proximally. Place speed back into impression. teeth or pressure may cause teeth back into distortion.)• Remove excess acrylic flashing from outside of flask, as hardened acrylic• Place 30ccmovement Denture Repair• Place 30cc Jet Jet of hinge and will inhibit of of Denture Repair• powder into measuringflask,cup. Add thumb screw. measuring powder into Remove denture from cup. Add• 15cc of Jet liquid excesspreviously 15cc of Jet all and mix for Cure foraway liquid and mix for clearing 15 minutes as acrylic.• 10 seconds.smooth finish. 10 seconds. Grind to a instructed.• Pour 75% of mixture into lower• Polish 75%pumice, then into lower• Pour with Pour remaining half of flask. of mixture high shine.• acrylic over palate forremaining half of flask. Pour upper half Use Jet Adjusters on polishing of flask. over palate on upper half acrylic and characterizing teeth. of flask.• With slow and Seal to fill in any Finish with Jet steady pressure,• With and secure and leavepressure, close slow and flask. (Excess surface porosity steady a close and secure flask. (Excess speed or pressure may cause shiny, finished surface. distortion.)pressure may cause speed or• Remove excess acrylic flashing from distortion.) outside of flask, as hardened acrylic• Removemovement of hinge and will inhibit excess acrylic flashing thumb outside of flask, as hardened from screw.• Cure forwill minutes movement of acrylic 15 inhibit as previously instructed. thumb screw. hinge and• Cure for 15 minutes as previously instructed.• Use Jet Adjusters for polishing and characterizing teeth.
  4. 4. 10 seconds. • Pour 75% of mixture into lower • half of flask.denture from flask, • Remove Pour from flask, Remove denture remaining acrylic over palate on upper half clearing away all excess acrylic. clearing away all excess acrylic. • of flask. toa smooth finish. • Grindto and steady finish. Grind •• With slow a smooth pressure, Polish with pumice, then • Polish with pumice, then closeshine. high and secure flask. (Excess speed shine. high or pressure may cause distortion.) • Remove excess acrylic flashing from outside of flask, as hardened acrylic will inhibit movement of hinge and thumb screw. • Cure for 15 minutes as previously instructed. •• UseJet Adjusters for polishing Use Jet Adjusters for polishing and characterizing teeth. and characterizing teeth. •• Finishwith Jet Seal to to fill in any Finish with Jet Seal fill in any surface porosity and leave a a surface porosity and leave shiny, finished surface. shiny, finished surface. CLEAR SURGICAL GUIDE / IMPLANT STENTOther Materials/Equipment NeededSilicone Spray SpatulaAlginate Measuring CupBur, pumice, lab polish Aquapres (pressure curing unit),Jet Liquid optionalOrtho-Jet Powder Clear (for clear guide)Jet XR Powder (for radiopaque appliance) Shadow and OpaqueInstructions for Use - Clear Guide:Follow Steps 1 – 5 as shown for Denture Duplication.
  5. 5. 6. Place 30 cc of Ortho-Jet powder into a measuring cup. Add15 cc of Jet liquid and mix for 10 seconds. Pour ¾ of mixtureinto the impression of the denture in the lower half of flask.Ensure that acrylic flows completely into all incisal and occlusalspaces without trapping any air.Pour the rest of the mixture over the palate on the upper half ofthe flask.7. With slow and steady pressure close and secure flask. (Excessspeed or pressure may cause distortion.) Cure for 20 minuteseither on bench or, for best results in Aquapres at 30 psi.Follow Step 9 for Denture Duplication to complete procedure.Instructions for Use - Radiopaque Appliance:Follow steps 1 – 5 as shown for Denture Duplication.6. Follow instructions for Denture Duplication, replacing the JetTooth Shade powder with the Jet XR Opaque powder.7. Same as for Denture Duplication.8. Follow instructions for Denture Duplication, replacing the JetDenture Repair powder with the Jet XR Shadow powder.Follow Step 9 for Denture Duplication to complete procedure.
  6. 6. WarrantyManufacturer warrants this product to be free from manufacturingdefects for one year from date of purchase. Warranty is void ifproduct is used for other than intended purpose or other thaninstructed.MediMark® EuropeBP 233238033 Grenoble Cedex 2FranceLang Dental Mfg. Co., Inc. TMWheeling, IL 60090-0969 USAwww.LangDental.comMade in USAPh 847-215-6622Fax 847-215-6678LDD 0398 R.6

×