GeoVision : Video Management Solutions : How to : Trigger GV-NVR Thru AS-200

  • 227 views
Uploaded on

GeoVision : Video Management Solutions : How to : Trigger GV-NVR Thru AS-200

GeoVision : Video Management Solutions : How to : Trigger GV-NVR Thru AS-200

  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Be the first to comment
    Be the first to like this
No Downloads

Views

Total Views
227
On Slideshare
0
From Embeds
0
Number of Embeds
0

Actions

Shares
Downloads
2
Comments
0
Likes
0

Embeds 0

No embeds

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
    No notes for slide

Transcript

  • 1. How to Trigger DVR Recording through GV-AS200 Controller Article ID: GV-33-08-07-21 Release Date: 2008/7/21Applied toGV-AS200 ControllerGV-System/GV-NVR (DVR)SummaryGV-AS200 Controller can work in conjunction with the DVR to start and stop recording oncethe exit and entry doors are unlocked. There are two applications in the case:1. The entry and exit doors are limited to one person access. When a designated person unlocks the entry door, the DVR starts recording. When the person leaves from the exit door, the DVR stops recording.2. More than one person can access the entry and exit doors. When people unlock the entry door, the DVR starts recording for a set period of time. When people leave from the exit door, the DVR starts recording again for a set period of time.In the two applications, the GV-NET/IO Card installed on the DVR is connected to bothoutputs of Door B and Door D on the GV-AS200 module. When Door A is opened, the signalof Wiegand A will be transmitted to Wiegand B (Door B) and it will trigger the DVR to startrecording. When Door C is opened, the signal of Wiegand C will be transmitted to Wiegand D(Door D) and it will trigger the DVR to start or stop recording.Requirements• 4-door modules: GV-AS200-4 or GV-AS200-4E• DVR equipped with GV-NET/IO CardGeoVision Inc. 1 Revision Date: 2008/7/21
  • 2. To set the application for one person accessIn this application, Door A is defined as the entry door, Door C is defined as the exit door, DoorB is set to trigger the DVR to start recording, and Door D is set to trigger the DVR to stoprecording.1. The work mode of GV-AS200 Controller must be set to One Way Control. By default, the work mode is One Way Control. If the default setting has been changed, use GV-ASKeypad to modify it.2. Connect the card reader to the Wiegand A inputs. Then connect the D0 and D1 pins of Wiegand A and Wiegand B together, as illustrated below. GND BZ RL GL D1 D0 12V GND BZ RL GL D1 D0 12VGeoVision Inc. 2 Revision Date: 2008/7/21
  • 3. 3. Connect the Door + pin of Door B outputs to the Input 1 pin of GV-NET/IO Card. Then connect the Urgent 1 pin of Door B outputs to the Ground pin of GV-NET/IO Card, as illustrated below. Please note don’t connect any power to the Door B outputs.4. Set the Door Relay Switch of Door B to NO.5. Connect the card reader to the Wiegand C inputs. Then connect the D0 and D1 pins of Wiegand C and Wiegand D together, as illustrated below. GV-Reader Wiegand D Wiegand CGeoVision Inc. 3 Revision Date: 2008/7/21
  • 4. 6. Connect the Door + pin of Door D outputs to the Input 1 pin of GV-NET/IO Card. Then connect the Urgent 1 pin of Door D outputs to the Ground pin of GV-NET/IO Card, as illustrated below. Please note don’t connect any power to the Door D outputs.7. Set the Door Relay Switch of Door D to NO.GeoVision Inc. 4 Revision Date: 2008/7/21
  • 5. 8. It is required to allow the accessibility of Door B and Door D in order to start and stop recording once the Door A and Door C are unlocked.9. To set the DVR, follow these steps: a. Click the Configure button, click Accessories, click I/O Application and click I/O Application Setting. The I/O Application dialog box appears. b. Select Momentary Mode and click Start/Stop Camera Monitor by I/O. c. Set Start Pin to Mod. 1 and Pin 1. Then set Stop Pin to Mod. 1 and Pin 1.GeoVision Inc. 5 Revision Date: 2008/7/21
  • 6. To set the application for many people accessIn this application, Door A is defined as the entry door, Door C is defined as the exit door, andboth Door B and Door D are set to trigger the DVR to start recording.1. The work mode of GV-AS200 Controller must be set to One Way Control. By default, the work mode is One Way Control. If the default setting has been changed, use GV-ASKeypad to modify it.2. Connect the card reader to the Wiegand A inputs. Then connect the D0 and D1 pins of Wiegand A and Wiegand B together, as illustrated below. GND BZ RL GL D1 D0 12V GND BZ RL GL D1 D0 12VGeoVision Inc. 6 Revision Date: 2008/7/21
  • 7. 3. Connect the Door + pin of Door B outputs to the Input 1 pin of GV-NET/IO Card. Then connect the Urgent 1 pin of Door B outputs to the Ground pin of GV-NET/IO Card, as illustrated below. Please note don’t connect any power to the Door B outputs.4. Set the Door Relay Switch of Door B to NO.GeoVision Inc. 7 Revision Date: 2008/7/21
  • 8. 5. Connect the card reader to the Wiegand C inputs. Then connect the D0 and D1 pins of Wiegand C and Wiegand D together, as illustrated below. GV-Reader Wiegand D Wiegand C6. Connect the Door + pin of Door D outputs to the Input 1 pin of GV-NET/IO Card. Then connect the Urgent 1 pin of Door D outputs to the Ground pin of GV-NET/IO Card, as illustrated below. Please note don’t connect any power to the Door D outputs.7. Set the Door Relay Switch of Door D to NO.GeoVision Inc. 8 Revision Date: 2008/7/21
  • 9. 8. It is required to allow the accessibility of Door B and Door D in order to trigger recording when the Door A and Door C are unlocked.9. To set the time length for recording, enter the number of seconds in the Lock Reset Time field. After the specified time expired, the door will automatically be locked and the DVR will stop recording. This setting is required for Door A and Door C.GeoVision Inc. 9 Revision Date: 2008/7/21
  • 10. 10. To set the DVR, follow these steps: a. Click the Configure button, click Accessories, click I/O Application and click I/O Application Setting. The I/O Application dialog box appears. b. Select Maintained Mode and click Start/Stop Camera Monitor by I/O. c. Set Start/Stop Pin to Mod. 1 and Pin 1.GeoVision Inc. 10 Revision Date: 2008/7/21