• Share
  • Email
  • Embed
  • Like
  • Save
  • Private Content
Dt process journal
 

Dt process journal

on

  • 265 views

 

Statistics

Views

Total Views
265
Views on SlideShare
265
Embed Views
0

Actions

Likes
0
Downloads
1
Comments
0

0 Embeds 0

No embeds

Accessibility

Categories

Upload Details

Uploaded via as Microsoft Word

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

    Dt process journal Dt process journal Document Transcript

    • Design & Technology process journal <br /> <br /> Misaki Kameda<br />2011- 1- 10, Monday<br />Measuring and marking out.<br />What I did<br />Today, I entered making my project. First, I measured the part of bottom, and its size is length 500 mm and width 300mm. Then I cut them out along the line by using across saw. The plywood is hard to cut; therefore I took a lot of time to cut one piece. There is reason that I didn’t use saw after winter vacation. But I also think today’s work was kind of great.<br />Change to my plan<br />I didn’t change my plan yet.<br />Why<br />Because I think my plan still seems to be ok.<br />Emotion<br />I was enjoying today’s work because I finished cut bottom part out.<br />What is next?<br />I will measure and mark part of side where it will join with the part of bottom at next time.<br />2011-1-11, Tuesday<br />Today, I measured a part of side where it will joint with the part of bottom. These sizes are width 300mm and length 450 mm. Then I cut them out along the line by using genet saw. But I sometime couldn’t cut along the line therefore I thought I have to check whether along the line or not when I’m cutting them.<br />2011-1-14, Friday<br />Today, I finished cutting part of side and shaving the surface to make flat with a file. Then I write line to joint with part of bottom on the part of side by using the ruler. I think today’s work was great.<br />2011-1-17, Monday<br />Today, I started cutting part of side to joint with part of bottom by using across saw. But using this saw was hard to cut, therefore I changed to pull saw. The saw was better than across saw to cut.<br />2011-1-18, Tuesday<br />Today, I finished cutting part of side to joint with part of bottom. But the cut end of the wood was not flat. Then I noticed I had to keep watching line during cutting them. Therefore I had to fix it to make flat. I will be careful about keeping watch line when I ‘m cutting something. I will make surface of wood to flat at next time.<br />2011-1-24<br />Cutting out base part of my tree<br />Today, I cut and made to flat surface of the wood by using pull saw and a smoothly plane, because when I was cutting them out I couldn’t along the line exactly, therefore the surface is rough and not correct size. By using the plane and pull saw I could fix it but it looks difficult. Also, I had some problem that the tree was lucking while having cut. Therefore I fixed it by using glue in older to reset to original shape, and to settle I was using the stopper as you can see in the picture. Then because of that, I have to wait. After finish this step, I made hole of the wood to join bottom part and side part by using a drill. When I had to use the drill, I was nervous because I haven’t used it before. But this problem was solved by my teacher he helped me.<br />In this picture, I’m shaving to make flat.<br />In this picture, the fragment was joined to the piece.<br />Change to my plan<br />I think I have to early to finish this work, therefore I will do fast next time.<br />Why<br />Because I wasted time to fix problem therefore I have to finish it early.<br />Emotion<br />I was completely happy because my problem fixed. Before it was fixed, I really worried about it therefore I was relived.<br />What is next?<br />Next time I will continue making hole to join the two pieces by using the drill and wait for settling piece, which was lacking.<br />2011-1- 25- Tuesday<br />Jointing base of my tree bookshelf<br />What did I do?<br />Today, I finished making hole on the wood by using the drill and jointing the base part by using a nail, driver and glue. But I first made mistake in the drill therefore one of the hole is beggar than other one; I have to fix it in the feature. In addition, I learned how to use the driver as pushing and rotating. After I finished jointing the base part, I marked and measured the side part, which will be support part of my tree bookshelf, and the size of the piece is width 300cm, length 600. First I cut them out by using gent saw but I noticed that is difficult to cut the piece, then I changed to cross saw. By using the cross saw I could cut out fast than before. Today I only finished cutting out one piece, therefore I will cut out one more next time.<br />In this picture, I’m cutting out piece by using the cross cut saw.<br />Jointing the base part by using glue and nail<br />Change to my plan<br />I think I have to fix problem that one of the hole is bigger than other one. Therefore my plan will be late than original one.<br />Why<br />Because it didn’t need there and its looks so not good. Also they have 4 hole on the wood even though there only needs 3 hole.<br />Emotion<br />Today, I’m completely happy because I finished jointing the base part, and I could imagine how my product will be.<br />What is next time?<br />Next time, I will cut out one more piece and measure and mark out top part. I also hope that I will entire next work.<br />2011-28-friday<br />Title: Cutting out and marking out side of my tree bookshelf<br />What did i do<br />Today, I kept working on cut and mark out side of my tree book shelf by using pencil, ruler, tri square and a cross cut saw. The size of side part is width 300mm, length 600mm same as yesterday part. cutting this size of wood was very hard to cut out because the material is thick but this time, I could cut faster and easier than last time. I think because I now know how to cut and how difficult it is this helped me. As for the cause of that is having experience. I think today's work was favorable and I also think I have to be more careful when marking out because It takes and can waste much time. Therefore I want to be more efficient next time.<br />In this picture, I'm marking out a board using a pencil and ruler<br />changes to my plan<br />It had to change my plan little bit that part of top of my tree book shelf will make smaller than my plan. It will be fixed 200mm size from 300mm.<br />Why<br />because it was too big to join with other part.<br />Emotion<br />Today, I felt completely happy because I could cut out and mark out smooth.<br />What is next time<br />I will cut and mark out top part which is width 300mm, length 20mm.<br />Learner profile<br />I think I was thinker at this class because I estimated about which size of top part will fit with side part. and how all the planning helps me to know what is coming up next.<br />2011-2-08-Tuesday<br />title:cutting out and making out body part of my tree bookshelf to join top part<br />What I did <br />Today, I started making body part to join top part and base part. To make body part as joining with top part and base part , I marked out by using ruler and pencil. After that, I started cutting out above the line, which I marked out, by using a pull saw.But its surface was rough therefore I had to make flat by using a smoothing plane. Using the smoothing plane is hard to use to me,so I changed to a file. After finished it, I tried to join with base part and I encountered problem that it doesn't fit well. To fix this problem, I changed side, where it would connect with based part, to right from left.<br />In this picture, I'm shaving surface of body part of my tree bookshelf to join with base part by using a smoothing plane.<br />Changes to my plan and why<br />As written before, I changed side, where it would connect with based part, to right from left. But I started cutting out other piece of body part before I noticed about this problem, therefore I will fix other piece to fit with left size.<br />What is next time?<br />I need cut out other piece of body part to join with base part and cut top part which size is width 300mm,length 200mm.<br />Emotion<br />Today, I was completely happy because I could see how my product will become.<br />Learner profile<br />Today, I think I was communicator because I consider about how my product will connect with base part of my tree bookshelf with my instructor.<br />2011-02-11-Friday<br />Title:Jointing body part and base part.<br />Today, I kept cutting out body part to join with base part by using a pull saw and test whether the base part and the body part could fit, and then It seems to be ok.<br />After that I started making hole to join these part. To make hole, first I confirmed exact connecting place on body part and base part by tapping with nail and hammer.Then I made hole by using a drill and connect body and base part by using screw and screw driver as you can see a picture. In addition, I could see the part, it is base and body part,was pretty level by using a level ruler. After that, I marked out top part of my tree bookshelf which size is width 300mm, length 200mm.<br />In this picture, a base part and body part of my tree bookshelf is jointing.<br />Emotion<br />I was completely happy and fun at today's working because I could jointing these part as you can see picture and I think I my plan advanced so much than before.<br />Changes to my plane<br />I think my plan seems be ok therefore it will not change. My Gantt Chart supposed to finish it until feb 14th.<br />Why<br />Because I completed jointing and I couldn't know whether it has problem before I connect top part with these part.<br />Leaner profile<br />Today, I was thinker because I think how to join body and base part.<br />2011-02-14-friday<br />Deciding where I will insert a partition shelf into the body part.<br />Today, I measured that hight is the body part of my tree bookshelf by using a ruler and pencil to decide where partition plate insert the body part. Then I could see its hight is 440mm. After that, I measured size of book to know how big of book store to my bookshelf, and then normal side of book was 250 mm. Through the measurement I decided that a low of partition plate is inserted in the place of 250 mm and it will be used for bigger book. Then, between other part and higher partition plane is 150mm to 20 mm, therefore it will be for small books. To mark out line of that, I used a level ruler to write a straight line. After I finished this work, I started taking out body part from base part by using a screw driver to join with the partition plane.<br />In this picture, I'm taking out a screw from the base part.<br />Emotion<br />I enjoyed today's working, because I could see how my product will become.<br />Changes to my plane<br />My plan was changed little bit that is taking out screw nail which is used to connect between base part and body part. Therefore I put new item in the gantt chart.<br />Why<br />Because partition plane has to insert to body part of my tree bookshelf.<br />What is next time?<br />I need cutting out top part and partition plane to join with the body part.<br />Leaner profile<br />Today, I was communicator because I consider about where I will insert a partition plate into the body part with my instructor.<br />2011-02-15-Tuesday<br />Taking out body part from base part and making a cavity at both end of the base part.<br />Today, I kept working on taking out body part from base part by using a screwdriver. After I finished that, I stated making a cavity at both end of the base part to insert partition shelf. To make this cavity, my instructor helped me to make shallow cut at the body part of my tree bookshelf by using a machine with adjuster. By using the machine with adjuster, it could cut exact place where I marked out before. After that, I plane this shallow cut to make cavity by using chisel and wooden mallet. Having the chisel level, striking on the place where a top of handle of chisel with the wooden mallet to be flat cavity.When doing this working, I was careful about the do not dig this cavity. <br />In this picture,I'm planing the cavity at the body part.<br />Changes to my plan<br />I didn't put this progress in my gantt chart, therefore I have to put it my gantt chart and It takes time to insert partition shelf into the body part than I expected.<br />Why<br />because I thought I would cut edge like slant before I was working this progress.<br />Emotion<br />I was completely happy because I think that I would insert partition shelf into the body part at next time.<br />What is next time?<br />I will plane the cavity to be flat and Insert partition shelf into the body part at next time.<br />Leaner profile<br />Today, I was observer because when my instructor was using the machine to help me to make shallow cut, I gained knowledge how to use this machine and what is machined used.<br />2011-02-18-friday<br />Inserting partition shelf into body part.<br />Today, I kept working on that plane shallow cut to make cavity by using chisel and wooden mallet. Having the chisel level, striking on the place where a top of handle of chisel with the wooden mallet to be flat cavity.After that, my instructor helped me to cut top part and partition shelf out by using machine, and then I inserted partition shelf into the body part. Then I fixed body part and partition by using a clamp and I marked out point where will be made hole. After I finished that, I started making hole at the point by using drill. To make hole, I used two different drill bit, one of these is thin and long which was used to make hole to inner part, and other one is bigger than another one which was used to fit with the top of the nail. <br />In this picture, the partition shelf is inserting into the body part, and the body part and base part are jointing .<br />Emotion<br />Today, I was confused about what should I do, therefore I thought I have to grasp a process of my work.<br />Changes to plan<br />My plan will change little bit that is shape of branch part of my tree bookshelf. In my final design, the branch part shape was like real tree branch but It will be changed.<br />Why<br />It is kind of hard to make and difficult to enclose the book with branch shape shelf.<br />What is next time.<br />Next time, I have to finish making hole by using drill and put nail into between body part and partition shelf.<br />Learner profile<br />Today, I was thinker because I was confused and I consider about what I should do.<br />2011-02-21-Monday<br />Making hole by using drill.<br />Today,I kept working on making drill at point ,where I wrote at the body part and top part, to joint body part and partition part. To make hole, I used two different drill bit, one of these is thin and long which was used to make hole to inner part, other one is bigger than another one which was used to fit with the top of the nail as last friday. During I make hole, I noticed about one of holes are in wrong place, therefore I have to make hole at other place. After I finished making hole at the body part I screwed this part by using a screw drill.Then,I took screw out which I screwed before, and I started making hole bigger at the top part. But I couldn't finish today therefore I will finish next time.<br />In this picture, we can see hole at the top part.<br />Emotion<br />I was completely happy because the work almost finish today and I think I will join body part and top part next time.<br />Changes to plan<br />I didn't put this progress, which I have to use two different type drill bit to make hole, in my gantt chart, therefore I have to put it my gantt chart and It takes time than I expected before.<br />Why<br />Because I thought that I could make hole by using one drill bit.<br />What is next time?<br />I need make hole at the top part ,and screw body part and partition part by using drill.<br />Learner profile<br />Today, I was thinker because I consider about how to use a drill more easy.<br />2011-02-22-Tuesday<br />jointing partition shelf and body part.<br />Today, I finished making hole at top part of my tree book shelf, and then I finished making hole at the body part to be big than before by using a drill. In addition, I made new hole because I had noticed about one of holes are in wrong place yesterday. After that, I separated partition part from body part to joint them by using glue and screw. To joint body part and partition part, I first glued a surface of the cavity and connected partition part by using wooden mallet.<br />Then I checked whether the body part and partition part is a right angle or not by using a square. When the body part and partition part was a right angle, I started jointing body part and partition part by using screw and a screw driver.After I finished jointing body part and partition part, I fixed these parts by using clamp.<br /><br />In this picture, the body part and partition part are fixed by using a sliding clamp.<br />Changes to plan<br />I think it doesn't need to change because It seems be ok. However the process of my product is kind of late by comparing with my gantt chart, therefore I have to be early to work.<br />Why<br />Because I took much times to make hole at the body part and top part by using drill.<br />Emotion<br />Today, I was completely happy because I finished jointing body part and partition part finally.<br />What is next time<br />Next time, I have to glue and screw top part and body part and cut out brunch shelf part of my tree bookshelf.<br />Leaner profile<br />I was communicator because I considered about how to fix the body part and partition part by using clamp with my instructor.<br />2011-02-28-Tuesday<br />Screwing and glueing top part and body part.<br />Today, I finished screwing and gluing top part and body part. To joint body part and top part, I first glued a surface of body part and screwed top part and body part by using a screw and a screw driver.Then I checked whether there is an opening between top part and body part , then I found there was fine opening. After I found it, I fixed this opening by using a wooden mallet, and then I tightened nail hard not to make the opening. Then I tried to be clear a line of the branch part at the piece to cut out it,and then I started cutting branch part of my tree bookshelf by using a saw and clamp.<br /> <br />In this picture, the top part of my tree shelf screwed with body part.<br />In this picture, we can see that partition part and top part connected with body part.<br />Changes to my plan<br />The changes is same as last time.I think it doesn't need to change because It seems be ok. However the process of my product is kind of late by comparing with my gantt chart, therefore I have to be early to work.<br />Because<br />I took this period only to finish screwing and glueing top part and body part.<br />Emotion<br />I was enjoying this work because I finished connecting body part and shelf.<br />What is next time?<br />I need to cut branch shelf part of my tree bookshelf next time.<br />Learner Profile<br />I was thinker because I consider about how to fix the opening between top part and the body part when I found it.<br />2011-03-01-Tuesday<br />Cutting a branch shape part of my tree book shelf out.<br />Today, I kept working on cutting branch part of my tree bookshelf. The branch part has curvy line and straight line , then I decided to start cutting straight line part first. To cut it out, I first used a gent saw and a sliding clamp. But my instructor recommended to me using other saw, because the saw only has short edge and it was hard to cut it. Then I changed saw to a cross saw, and the saw could cut them out fast than other one. After I cut along straight line , my instructor helped me to cut them along curvy line by using a machine. I finished making 3 piece of branch part in this class, and I also noticed about I need to draw 2 more piece of branch part.<br />In this movie, I'm cutting branch part out by using a gent saw.<br />Change to my plane<br />My process of product is kind of late than my gantt chart, therefore I have to finish more fast this part of work.<br />Why<br />I took much time to cut piece out by using a saw, because I first used not suitable saw.<br />What is next time?<br />I have to finish cutting out branch part and jointing it with body part.<br />emotion<br />I enjoyed today's working, because I could see how my product will become.<br />Learner profile <br />Today, I was thinker because I consider about which kind of saw is best to cut out.<br />2011-03-04-Friday<br />Cutting branch shelf out<br />Today, I kept working on cutting two pieces of branch part of my tree bookshelf. The 2 pieces is that I forgot marking out last class, then I marked out these piece by tracing with piece which is cut out before. After that, I started cutting straight line part by using a gent saw and sliding clamp. Then my instructor helped me to cut their along curvy line by using a machine, when I finished cut out. After that, I shaved surface and circumference of the branch shelf to fix shave. To fix the shave, I used a smoothly plane. Today, I couldn't finished cutting curvy line part therefore I have to finish it next time.<br />In this picture, I'm shaving the surface of the branch shelf by using a smoothly plane.<br />Changes to my plan<br />I have to put this progress, which is shaving the surface of branch shelf, in my gantt plan.<br />Why<br />Because I didn't expect that I have to do it before, therefore I didn't know this progress.<br />What is next time?<br />I have to finish cut the curvy line of the branch shave next time .<br />Emotion<br />I was completely happy because I think that I can' finish making branch part next time.<br />Learner profile<br />I was thinker because I consider about how to make the surface of branch shelf to be flat.<br />2011-03-07-Monday<br />Cutting branch shape shelf out<br />Today, I kept working on cutting curvy line of the branch shape shelf by using a gent saw and sliding clump. Then, there were two problems in this process. One of the problems is that fix the piece on the desk by using a sliding clump because the piece is too little to fix it. Therefore it couldn't fix as tight, and move many time, so I change place many time where is fixed with the sliding clump to solve it. Other one of problem is making shallow cut on the piece to cut it by using a cross saw, therefore I solve this problem by using a gent saw to make it. After that, I started shaving surface to make same shape and size.<br />Changes to my plan<br />My process of product is kind of late than my gantt chart; therefore I have to finish faster this part of work.<br />Why <br />Because I couldn't finish cutting out all branch shelf, though I think I could finish this class.<br />What is next time?<br />I have to cut one more curvy line of the branch shelf and shave the surface of branch shelf next time.<br />Emotion<br />I enjoyed working on today7s process because I finished 4 piece of the branch shelf.<br />Learner Profile<br />I was thinker because I considered about how to solve the problem when I encountered two problems.<br />2011-03-08<br />Cutting and shaving branch shelf<br />Today, I finished cutting branch shelf out by using a gent saw and clump, also my instructor helped me to cut one of curvy line by using machine. After that, I started shaving projection of branch shelf because I cut 2 of curvy line of branch shelf by using a gent saw therefore I couldn't cut along the curvy line exactly and then there is several projection. To shave and fix the projection of branch shelf, I used a flat plane , half-round plane and sliding clump. However, using these plane took much time to shave to be along,so I was recommend my instructor to use the shave machine. With using this machine, I could reduce time for this work and then the surface of branch shelf become smoothy than before.<br />In this picture, I'm shaving surface of branch shelf by using flat plane,<br />Changes to my plan<br />I think my plane become to be along my gantt plane, therefore it doesn't need any changes.<br />Why<br />Because I finished cutting branch shelf out this class.<br />What is next time?<br />I need finish shaving surface of branch shelf to be smoothy.<br />Emotion<br />Today,I was completely happy because I finally finish the branch shelf parts.<br />Learner profile<br />Today, I was observer because when my instructor was using the machine to help me to make branch shelf to be smoothy , I gained knowledge how to use this machine and how to make to be smoothy and flat.<br />2011-03-11-Friday<br />Jointing branch shelf with body part of my tree shelf<br />Today, I finished shaving the surface of branch shelf of my tree bookshelf by using the machine and flat plane, and then finished making branch parts. After that, I started marking and measuring where the branch shelf joint with body part, and I also decided about size of plate which will be putted on branch shelf. However , I couldn't decide specific detail by myself, then my instructor helped me to decide about these things. Then, we started making hole on the body part to screw branch shelf with body part by using a drill,after we decide size of this plate and cut it out. After finished this work, I screw body part to body part by using screw and screw driver.<br />Changes to my plane<br />In my plan, I had decided that plate , which will be putted on, length is 300mm but I changed it to be smaller than before.<br />Why<br />Because It is too big to joint the body part of my tree book shelf.<br />What is next time ?<br />I need make other hole to joint branch shelf with body part by using drill.<br />Emotion<br />I was completely happy because I could see how my product will become.<br />Learner profile<br />Today, I was observer because when my instructor was making hole to join branch shelf with the body part, I gained knowledge how to use and make this kind of hole.<br />2011-03-14-Monday<br />Jointing branch shelf with body part of my tree bookshelf<br />Today, I kept working on jointing branch shelf with body part of my tree bookshelf. To joint branch shelf with body part, I first found pair of branch which mostly fit each other. After that I made hole at one of branch ,where I tapped nail to leave point for knowing exact place, to connect with body part by using drill and then I screw it to body part by using a screw and screw driver. But, I was failed to screw to be flat at first time, therefore I took out the screw and then fixed it by using wooden mallet. After I finished this progress, I started marking and measuring body part to decide place where branch shelf will be connect by using pencil and ruler .<br />In this picture, I' m making hole at surface of branch shelf by using drill.<br />Changes to my plane<br />I have to decide where branch shelf will be jointed with body part, because I didn't decide exact place in my plan.<br />Why<br />Because I forgot thinking about this part detail when I considered about it.<br />What is next time?<br />I have to finish marking and measuring where branch shelf will be jointed with body part.<br />Emotion<br />I was completely happy because I could see how my product will become.<br />Learner profile<br />Today,I was thinker because I consider about how the branch shelf connect with body shelf to be flat, and then I found way to fixe it .<br />2011-03-15-Tuesday<br />Making hole at the body part<br />Today, I kept working on marking and making hole at the body part of my tree bookshelf to join with branch shelf. First, I was marking and measuring body part to decide place where branch shelf will be connect by using pencil and ruler , but I took much time to decide it because first time I marked out near from the inserted shelf. So, I had to change this place. After that, I started making hole at the body part by using drill at inside and outside of the body plate. To make hole at inside, the drill's length was too long for the space and then it couldn't reach at the place where I will make hole. Therefore, I changed to smaller one and then could finish making one part of hole.<br />In this picture, I'm making hole by using a drill.<br />Changes to my plan<br />I think my plane become to be along my gantt plane, therefore it doesn't need any changes.<br />Why<br />Because I think I could finish making hole at the body par and jointing branch shelf.<br />What is next time?<br />I need to finish making hole at the body par and jointing branch shelf.<br />Emotion<br />I was completely happy because I could see how my product will become.<br />Learner profile<br />Today, I was thinker because I tried to find best way when I was at a loss about making hole.<br />2011-03-18-Friday<br />Making hole at the body part and jointing branch shelf with body part<br />What I did<br />Today, I kept working on make hole at body part, and joint branch shelf with branch part of my tree bookshelf. To make hole, I first measure place of last one where the branch shelf will be joint,but I was at a loss about deciding palace and an interval between shelf. Then my instructor helped me to decide it, and then we decide the branch would connect bottom of body part. After that, I started making hole at the bottom of body part by using drill. First, making hole at inside and outside of body part,and then I was taping screw through the hole by using a hammer to examine exact place where I will make hole at surface of branch shelf to connect. Then, I started glueing and jointing branch shelf with body part by using glue, screw and screw driver after these process.<br />In this picture, I'm screwing branch shelf with body part of my tree bookshelf by using a screw and a driver.<br />Changes to my plan<br />I think my plane become to be along my gantt plane, therefore it seems be ok.<br />Why<br />Because I almost finished process of my project therefore I think I could finish my product as soon as.<br />What is next<br />I have to finish jointing branch shelf and making shelf which will be putted on branch shelf.<br />Emotion<br />Today, I was completely happy because I could see how my branch part become.<br />Learner Profile<br />I was thinker because I find way to solve my problem when I was at a loss about making hole to be fit with a screw.<br />2011-0321-Monday<br />Jointing branch shelf with body part of my tree book shelf<br />What I did<br />Today, I finished jointing branch shelf with body part of my tree book shelf. To finish it, I first take out one of branch shelfs , which was connected with body part at first time, because I didn't glue this before. After take it out, I glue surface of branch shelf and connect it with body part by using a glue , 5mm screw and a screw driver. In order to these step, I finished this process, then I intended to start making shelf which will be putted on the branch shelf. However, I couldn't find stuff to make it by myself, then I asked my instructor about it. When I asked my instructor about it, I was noticed about the surface of my branch shelf is not exact flat , then it will be tilt when the shelf putted on branch shelf by this problem. So, I recognized that I will have to fixed it by putting thin plate between the shelf and branch shelf next time. After that, I backed in my work,and then I made hole at the shelf which my instructor cut it out before by using drill and clump during I wait to find the stuff of the shelf.<br />In this picture, I 'm making hole at the shelf to help jointing by using the drill.<br />Changes to my plan<br />I think my plane become to be along my gantt plan, therefore it seems be ok,but I have to be hurry little bit.<br />Why<br />because I think I can finish this process at next class.<br />What is next time ?<br />I have to cut the shelf which will be putted on branch shelf out next time.<br />Emotion<br />I was completely happy because I finished jointing branch shelf with body part today.<br />Learner Profile<br />I was thinker because I find way to solve my problem when I was find problem as thus.<br />2011-03-22-Tuesday<br />Changing my plan<br />Today, I first finished making hole at the surface of the shelf, which will be putted on the branch shelf by using drill. Secondary, I shave the surface and circumference of body part and branch part of my tree bookshelf to make it be flat. When I finished this work, my instructor pointed out problem of my tree bookshelf. The problem is that using plywood for shelf ,which will be putted on branch shelf,will make my bookshelf heavy and the body part will not withstand from this weight.To fixed this problem, I changed material light one than the plywood one. Then, I started and finished cutting this shelf, which size is length 250mm, width 180mm, by using a tenon saw and clamps.<br />In this picture, I' m cutting shelf, which will be putted on branch shelf, by using a saw.<br />Changes to my plan<br />I changed material of the shelf to light one from plywood.<br />Why<br />because it will make my tree bookshelf heavy and my body part couldn't withstand.<br />What is next time<br />I have to finish joint the shelf with branch shelf.<br />Emotion<br />I was completely happy because I solve my problem as thus.<br />Learner profile<br />I was thinker because I find way to solve my problem when I was find problem.<br />Link to biomimicry<br />I think my bookshelf is becoming close to biomimicry. The part of branch shelf will hold book and stuff is close to natural tree because natural tree is kind of support things.<br />2011-03-25-Friday<br />Planing and Making hole at the shelf of my tree bookshelf<br />Today, I kept working on making the shelf which I changed material to light one from plywood. To joint this shelf with branch part, I have to shave surface of this shelf and make hole. First, I shaved surface and circumference of these shelfs to be flat and same size by using plane, clump. With using the plane and clump to shave, I took much time for this work. Therefore I changed equipment to shaving machine. By this changing, I could reduce time and my shelf was completely flat.<br />After I finished this work, I started working on making hole at surface of this shelf to joint branch shelf part. To make hole,I first measured and marked out where I will make hole by using pencil and ruler. Then, I started making hole by using drill.<br />In this picture, I'm making hole at this plate by using drill as thus.<br />Changes to my plane<br />I think my plane become to be along my gantt plane, therefore it seems be ok, but I still have to hurry little bit.<br />Why<br />Because I think I can joint the shelf with my branch part at next class.<br />What is next time ?<br />I have to finish making hole at this shelf and joint with branch shelf.<br />Emotion<br />I was in harry little bit today because I have to finish my product up until next week.<br />Learner Profile<br />Today, I was thinker because I used my knowledge for my work.<br />Link to biomimicry<br />I think my product become close to biomimicry because the branch part of my tree bookshelf will support book as natural tree<br />2011-03-29-Tuesday<br />Jointing the shelf with branch part of my tree bookshelf<br />Today, I was working on jointing the shelf with my bookshelf. To joint it with branch part, I first have to finish making drill at the shelf where I measured before by using drill and clumps. After I finished it, I taped screw through the hole to examine about where I should make hole at surface of branch part to joint it by using hammer. Then I made hole each surface of branch part by using drill, and joint shelf and branch part by using screw and a screw driver. When I finished this process, I encountered one problem that the branch part and the shelf don't fit as well. Therefore, I had to fix the problem by making other hole elsewhere.<br />Changes to my plan<br />I have to fix the problem as thus, therefore It takes much time to finish my product before I expected.<br />Why<br />Because, I didn't estimate time for fixing problem in my gantt chart.<br />What is next time ?<br />I have to fix this problem by inserting thin wood under the branch shelf at next time.<br />Emotion<br />Today, I was upset about this problem but it slightly was changed because I found way to fix it.<br />Learner profile<br />I think I was inquirer because I tried to ask how I will fix this problem, and then I could gain the measures of this problem.<br />2011-04-01-Friday<br />Planing all surface of my tree book shelf and fix the problem<br />Today, I first worked on fixing the problem which is one of branch part and shelf didn't fit . To fix this problem, I have to cut thin wood to triangle shape for inserting under the branch part. However cutting thin wood was too hard to me, and then I was helped by my instructor. After making triangle shape, I tried to insert the one under the branch shelf, and It became definitely fit with the branch shelf. But I encountered other problem again; that is the hole at the shelf and where I have to screw didn't match because the two branches were not parallel. Therefore it couldn't connect through triangle and branch fitted. For solving this problem, I push two branch shelf to inside by my hand, and then I screw it at same time.After I finished these activities as thus, I started planning all surface of my tree book shelf by using sandpaper to lose square.<br />In this picture, I'm planning all surface of my tree shelf to lose square by using sandpaper.<br />Change to my plan<br />I think my plane become to be along my gantt plane, therefore it seems be ok.<br />Why<br />Because I fixed problem and my product seems near the end.<br />What is next time?<br />I need to joint base part and body part by using screw, screw driver and glue. Also, I want to start painting if I can.<br />Emotion<br />Today, my feeling was changed to happy from upset because I fixed problem and then my uneasiness was disappeared.<br />Learner profile<br />I think I was observer because I gained knowledge by looking at work of my instructor when my instructor helped me to fix my problem of product.<br />2011-04-12-Tuesday<br />Planning all surface of my tree bookshelf and examining for jointing body part with base part<br />Today, I kept working on planning all circumference of my tree bookshelf, to lose square for safety by using sandpaper same as yesterday. After I finished that, I tested whether the base part and body part fit or not, and then the result of the testing is they fitted each other fortunately. I also tested about body part and base part are fitting as perpendicular by using level , and then it was definitely perpendicular. However the balance of these was not well because it didn't have support things, therefore , I decided to make support things later. In additional, I have to make canceling, where I made hole before to joint body part with base part, by using drill.<br />Changes to my plan<br />The change I have made is making support things where is between body part and base part because there is instability. In my gantt plan, there wasn't included this process therefore it will take much time than I expected before.<br />Why<br />Because I thought my product would be solid without support, therefore I didn't estimate that it would be instability and I have to make support for it.<br />What is next time ?<br />In next class, I have to finish many things which are making canceling, making support and jointing body part and base part. Also, I have to clean a pencil mark off ,before jointing body part and base part, for preparation of painting.<br />Emotion<br />At the first of this class, I was enjoying with my work, but my feeling was suddenly changed to nervous when I found problem of my product that I didn't expect.<br />Learner profile<br />Today, I was communicator because I asked my instructor about measures of problem when I encountered problem as thus.<br />2011-04-15<br />Erasing a pencil mark<br />Today, I first made canceling at the point ,where I will screw, to joint base part and body part by using drill. Then I started erasing the pencil mark that I had wrote for preparation to joint body and base parts. To erase the pencil mark, I first had used eraser but the pencil mark was thick and too hard to erase by using eraser. Therefore, my instructor recommended me to use sandpaper for it, then I changed method to this from using eraser. After that, I used two different kind of sandpaper, which are coarse one and fine one, and then pencil mark was erased as easy. In addition, I made change ,that I will not painting my product , when I erased pencil mark.<br />In this picture, I'm erasing pencil mark by using sandpaper.<br />Changes to plan<br />The change I have made is that I will not paint my product. In my final design, it is intended to paint to brown as natural tree, but I changed my plan as thus.<br />Why<br />Because I though material that I used is untouched tree color, and then I wanted to make natural product such as close to natural tree.<br />What is next time ?<br />I have to finish erasing pencil mark and jointing body and base part of my tree bookshelf.<br />Emotion<br />I was enjoyed to today's work because I could see how my branch part become.<br />Learner Profile<br />I think I was observer because I gained knowledge by looking at work of my instructor when my instructor helped me to fix my problem of product.<br />2011-04-18-Monday<br />Erasing pencil mark 2<br />Today, I kept working on erasing pencil mark by using sandpaper same as yesterday. Firstly, I started erasing outer of my tree bookshelf, and then it was hard to erase pencil mark because there are many protuberances, specifically branch part. my tree bookshelf has three branch shelf as random, therefore it interrupt me to erase pencil mark when I tried to erase pencil mark nearing the branch part . Because of that, I was regretted about I didn't erase pencil mark before I joint body part and branch part. As thus, erasing pencil mark was much hard than I expected before, and then I actually couldn't finish this work at this class.<br />In this picture, I' m erasing the pencil mark by using sandpaper.<br />Changes to my plan<br />I think my plan become to be along my gantt plan, therefore it seems be ok,but I have to be hurry little bit.<br />Why<br />Because I have taken much time to erase pencil mark as thus than I had expected before. therefore I have to do my work more early.<br />What is next time? <br />I have to finish erasing pencil mark and jointing body and base part of my tree bookshelf.<br />Emotion<br />I was completely happy because my product become near to the end.<br />Learner Profile<br />I think I was thinker because I considered how can I erase pencil mark easy as keep out of branch shelf.<br />2011- 04-19- Tuesday<br />Cleaning my tree bookshelf up<br />Today, I was still continuing erasing the pencil mark by using sandpaper same as yesterday. As I mentioned about how was difficult to erase pencil mark yesterday, erasing pencil mark around the branch part was still hard to me. Around this part, there is many line because I had measured many things ,such as length and width, to make all branch parts same when I was working on this part. Therefore, it always interrupt me to do it. In additional, there is other reason of this difficult is that I have to erase the pencil along direction of a wood line. Because of the difficult, I couldn't finish this work at this class.<br />In this picture, I' m cleaning pencil mark up by using the sandpaper.<br />Changes to my plan<br />I think my plan become to be along my gantt plan, therefore it seems be ok,but I have to be hurry little bit same as yesterday.<br />Why<br />Because I couldn't finish this work at this class although I planned it.<br />What is next time?<br />I have to finish erasing pencil mark and jointing body and base part of my tree bookshelf.<br />Emotion<br />Today, I was upset because I noticed I took much time to finish this work.<br />Learner profile<br />I think I was thinker because I considered how can I finish this work fast.<br />2011-04-22-Friday<br />Cleaning my tree bookshelf up and screwing<br />Firstly, I finished cleaning my tree bookshelf up by using sandpaper and then I plane circumference of my product by using flat plane. In planing process, I was careful to plane circumference to rounded as for finishing. Secondly, I started jointing body and base part of my tree bookshelf after I finished these processes . To joint base part and body part, I had to examine pair of base part and body part that I had decided such as A and B. Then I measure that my product is straight or not by using level before I screw it. After I confirmed my product is straight, I started screwing it by using screws and a screw driver<br />.<br /> <br />In these picture, I was planning and screwing my tree bookshelf.<br />Changes to my plan <br />I think my plan become to be along my gantt plan, therefore it seems be ok.<br />Why<br />Because I almost finished process that I have in my gent plan, also my product become tree shape as you can see in the picture.<br />What is next time?<br />I have to screw body part and base part of my tree shelf as level by using screw and screw driver after I confirm my product is straight or not.<br />Emotion<br />I was completely happy because my product become near to the end.<br />Learner profile<br />Today I was reflective because I was working on my product by using technique that I have leant until now.<br />2011-04-26-Tuesday<br />Planning circumference of my tree book shelf<br />Today, I was working on jointing body part and base part by using screw and screwdriver, however there were some gap between body part and base part when it is connected. Therefore I asked about it to my instructor and then my instructor said that I have to take screw out and cut the top of triangle shape base part. After I asked it, I took screw out and then cleaned some pencil mark, which I didn’t notice, up.<br />←(In this picture, all screw are taken)                   <br />            ( In this picture, I ‘ m cleaning the pencil mark up)<br />Change to my plan<br />The change that I have made is that I have to cut top of triangle shape base part to lost gap between body part and base part, as my instructor told me.<br />Why<br />Because the top of base part is not flat and then it is hard to join with body part of tree bookshelf.<br />What is next time?<br />I have to finish cutting the top of base part and screw body part and base part together again.<br />Emotion<br />Today, I was upset about the changes because I expected that I could finish this process in this class.<br />Learner Profile<br />I think I was inquirers because I asked my instructor about measures of the problem when I encountered it.<br />2011-04-29-Friday<br />Painting my tree bookshelf with varnish<br />Today, I finally finished cleaning pencil mark up by using a sandpaper, and then I jointed base part and body part. For joining base part and body part, I used level to make it straight, and then I screw these part together by using a screw and screw driver after I examined that body part and base part are jointed as straight. Then, I had big change that I will not paint my tree bookshelf with color, and then paint it with varnish instead of color. Before paint my tree bookshelf, I clean dust up by using brush not to stick on bookshelf with varnish. After that, I started painting bookshelf with varnish. <br />In this picture, I’m painting my tree bookshelf with varnish.<br />Change to my plan<br />Today, I had big change that I will not paint my tree bookshelf with color, and then it will be painted by varnish instead of color paint.<br />Why<br />Actually, I intended to paint it with brown color in my gent chart because I thought natural tree color is brown, however I noticed about the material I used is made by wood and the color is definitely nearest natural tree color.<br />What is next time?<br />Next time, I have to finish painting my tree shelf with varnish and finish my product.<br />Emotion<br />Today, I was completely happy because I finally finish jointing base part and body part and enter the process of painting.<br />Learner profile<br />Today, I was reflective because I used technique that I have learnt to joint base part and body part as straight by using level.<br />2011-05-03-Tuesday<br />Painting my tree bookshelf with varnish<br />Today, I was painting my tree bookshelf with varnish. Firstly, I painted the inside part of my tree bookshelf and dry these part while I was painting outside part of my product. After I finished painting all part of my product, I checked whether or not it has place that is not painted. By checking, I found place that is not painted and then paint the place again. Then, I finally finished making my product as well as I have expected before. After making, I showed my product instructor and test my product by storing many different types of books. The result of testing is very good and it is like ' tree of knowledge' when books were stored into my product.<br /> <br />In these pictures, I 'm testing my product whether or not it works by storing books.<br />Change to my plan<br />There were not any changes.<br />Why<br />Today, I was working on finishing of my product, therefore my product didn't need any change.<br />What is next time?<br />I'm going to start writing my final evaluation of this project.<br />Emotion<br />I was completely happy because I finally finished making my product and my product's looks become very nice.<br />Learner profile<br />Today, I was reflective because I used technique that I have learnt through this project.<br />