1.5MM ADD MATERIAL <ul><li>YELLOW INDICATES AREAS THAT WE NEED TO HAVE ADDED STOCK.  AREAS MARKED IN YELLOW ARE  ONLY  ARE...
 
 
 
4MM MATERIAL ADD <ul><li>RED ON YELLOW PAINT: </li></ul><ul><li>ADD 4MM TO WALL ON LEFT BANK DOWN IN WATER JACKET AREA. </...
 
 
ADD 3MM STOCK <ul><li>NEED TO ADD 3MM STOCK IN FOUR PLACES ON EACH BANK (8 TOTAL).  REFERENCE SLIDES 9 & 10. </li></ul><ul...
 
 
ADD 2.5MM STOCK <ul><li>BULKHEAD LOCKWIDTH (BEARING CAP INTERFERENCE PRESS FIT) </li></ul><ul><li>WHITE PAINT AREAS </li><...
<ul><li>4MM MACHINING STOCK MEASURED ON THESE 5 FACES </li></ul>
<ul><li>4MM MACHINING STOCK MEASURED ON THESE 5 FACES </li></ul>
<ul><li>4MM MACHINING STOCK MEASURED ON THESE 5 FACES </li></ul>
 
TILLER LOCATION-ORANGE PAINT <ul><li>SLIDE 17,  CYLINDER 5-LEFT DECK </li></ul><ul><li>SLIDE 18,  CYLINDER 5-LEFT DECK </l...
 
 
 
 
1.5 Ø  4.180 INCH (106.17MM) 55.88 MM 2.0 +/-1.4 2.0 +/-1.4
“C” LOCATOR  <ul><li>SLIDES 22,23,24 ARE REAR LOCATORS </li></ul><ul><li>SLIDES 25,26,27 ARE FRONT LOCATORS </li></ul>
 
 
 
 
 
 
Upcoming SlideShare
Loading in...5
×

Material Addition&Tillerdata

183

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
183
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
1
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Material Addition&Tillerdata

  1. 1. 1.5MM ADD MATERIAL <ul><li>YELLOW INDICATES AREAS THAT WE NEED TO HAVE ADDED STOCK. AREAS MARKED IN YELLOW ARE ONLY AREAS FOR ADDITIONAL MATERIAL, DO NOT ADD MATERIAL TO ENTIRE AREA!! REF. PIC 2, 3 & 4. </li></ul><ul><li>BEFORE CHANGE - 9.52MM (FROM CENTRELINE) </li></ul><ul><li>AFTER CHANGE – 10.97MM TO/ 11.23MM (FROM CENTRELINE) </li></ul><ul><li>(~1.5MM MATERIAL ADDED ON 8 BOSSES ON BOTH RH/LH SIDE) </li></ul>
  2. 5. 4MM MATERIAL ADD <ul><li>RED ON YELLOW PAINT: </li></ul><ul><li>ADD 4MM TO WALL ON LEFT BANK DOWN IN WATER JACKET AREA. </li></ul><ul><li>SLIDES 4, 6 & 7 (RED PAINT IS FAINT ON 7) </li></ul><ul><li>BEFORE CHANGE - 10.52 (FROM CENTRELINE) </li></ul><ul><li>AFTER CHANGE – 15.20MM (FROM CENTRELINE) </li></ul><ul><li>(4.6MM MATERIAL ADDED AT SLIDE NO.7) </li></ul><ul><li>ONLY FOR SLIDE NO 7 (RED PAINT MARKED) </li></ul>
  3. 8. ADD 3MM STOCK <ul><li>NEED TO ADD 3MM STOCK IN FOUR PLACES ON EACH BANK (8 TOTAL). REFERENCE SLIDES 9 & 10. </li></ul><ul><li>RED PAINT AREAS </li></ul><ul><li>BEFORE CHANGE - R 8.15mm (FROM CENTRELINE) </li></ul><ul><li>AFTER CHANGE – R 11.28 mm (FROM CENTRELINE) </li></ul><ul><li>(3MM MATERIAL IN RADIUS ADDED AT 8 PLACES </li></ul>
  4. 11. ADD 2.5MM STOCK <ul><li>BULKHEAD LOCKWIDTH (BEARING CAP INTERFERENCE PRESS FIT) </li></ul><ul><li>WHITE PAINT AREAS </li></ul><ul><li>10 PLACES (5 ON EACH SIDE) </li></ul><ul><li>REFERENCE SLIDE 12, 13, & 14 </li></ul><ul><li>MACHINING DIMENSION = 211.624 MM </li></ul><ul><li>ACTUAL MEASURED AS CAST DIMENTION = 202.260 MM </li></ul><ul><li>AVERAGE MACHINING STOCK 4.15 TO 4.72 MM ON EACH SIDE </li></ul>
  5. 12. <ul><li>4MM MACHINING STOCK MEASURED ON THESE 5 FACES </li></ul>
  6. 13. <ul><li>4MM MACHINING STOCK MEASURED ON THESE 5 FACES </li></ul>
  7. 14. <ul><li>4MM MACHINING STOCK MEASURED ON THESE 5 FACES </li></ul>
  8. 16. TILLER LOCATION-ORANGE PAINT <ul><li>SLIDE 17, CYLINDER 5-LEFT DECK </li></ul><ul><li>SLIDE 18, CYLINDER 5-LEFT DECK </li></ul><ul><li>SLIDE 19, CYLINDER 6-RIGHT DECK </li></ul><ul><li>SLIDE 20, CYLINDER 6-RIGHT DECK </li></ul><ul><li>2.5mm THICKNESS TILLER USED. </li></ul><ul><li>DETAIL OF LOCATION IN SLIDE NO.21 </li></ul>
  9. 21. 1.5 Ø 4.180 INCH (106.17MM) 55.88 MM 2.0 +/-1.4 2.0 +/-1.4
  10. 22. “C” LOCATOR <ul><li>SLIDES 22,23,24 ARE REAR LOCATORS </li></ul><ul><li>SLIDES 25,26,27 ARE FRONT LOCATORS </li></ul>
  1. A particular slide catching your eye?

    Clipping is a handy way to collect important slides you want to go back to later.

×