103320664 eigrp-sba


Published on

  • Be the first to comment

No Downloads
Total views
On SlideShare
From Embeds
Number of Embeds
Embeds 0
No embeds

No notes for slide

103320664 eigrp-sba

  1. 1. ERouting EIGRP PT Practice SBA
  2. 2. ERouting EIGRP PT Practice SBA A few things to keep in mind while completing this activity: 1. Do not use the browser Back button or close or reload any Exam windows during the exam. 2. Do not close Packet Tracer when you are done. It will close automatically. 3. Click the Submit Assessment button to submit your work.IntroductionIn this Packet Tracer Practice Skills-based Assessment, you will: • complete the configuration of a partially configured network • establish connectivity to the West Region and the Internet through the use of static and dynamic routing • verify connectivityAddressing Table Device Interface Address Subnet Mask Default Gateway S0/0/0 up N/A S0/0/1 do N/A EastHQ S0/1/0 up Internet S0/1/1 up Fa0/0 /25 N/A Fa0/1 /25 N/A E-Branch1 S0/0/0 /30 N/A S0/0/1 /30 N/A Fa0/0 /26 N/A Fa0/1 /26 N/A E-Branch2 S0/0/0 /30 N/A S0/0/1 N/A EPC1 NIC /28 EPC2 NIC EPC3 NIC /26 EPC4 NIC NetAdmin NIC /26 Note: The password for user EXEC mode is cisco. The password for privileged EXEC mode is class.Step 1: Configure the Device Basics. Note: Initially, you can only access router E-Branch2 through the console connection on NetAdmin.a. Configure the following on E-Branch2:• The router name is EB2.Router(config)# hostname EB2• The privileged EXEC mode uses the following encrypted password: class.
  3. 3. EB2(config)#enable secret class• Enable Telnet and console line logins and use the following password: cisco.EB2(config)#line vty 0 4EB2(config)#password classEB2(config)#loginEB2(config)#exit• Configure the banner message-of-the-day as Authorized access only!EB2(config)#banner motd %Authorized access only!%b. Using the Addressing Table, configure and activate all the necessary interfaces on E-Branch2.c. Configure correct host IP addressing.EB2#show ip interface briefEB2#show ip route• Configure EPC2 with the last IP address in the subnet. gateway• Configure EPC4 with the last IP address in the subnet. gateway 2: Discover the Network.a. Explore the network to determine the IP address of the serial interface that EastHQ uses to connect to E-Branch2.b. Remotely access EastHQ.EB2# show interfacesEB2# show cdp neighborsEB2# show ip routeEB2# telnet serial0/0/0EastHQ (config-if)#ip address
  4. 4. EastHQ (config-if)#no shutdownEastHQ (config-if)#exitEastHQ (config)#interface serial0/0/1EASTHQ(config-if)#ip address shutdownEASTHQ(config-if)#exitEASTHQ(config)#interface serial0/1/0EASTHQ(config-if)#ip address shutdownEASTHQ(config-if)#exitEASTHQ(config)#interface serial0/1/1EASTHQ(config-if)#ip address shutdownEASTHQ(config-if)#exitStep 3: Configure Static and Default Routing.a. Configure connectivity to the West Region.• Configure a static route on EastHQ to the entire West Region. The West Region uses the address space. Use the next-hop address argument.EastHQ#show ip routeEastHQ(config)#route ip• Configure a default route on EastHQ to send to the Internet all other traffic for destinations that are not found in the EastHQ routing table. Use the exit interface argument.EastHQ(config)#route ip serial0/1/0b. Verify static and default routing.EastHQ#show ip routeEastHQ#pingStep 4: Configure EIGRP Routing. Configure EIGRP on EastHQ, E-Branch1, and E-Branch2. a. Use AS number 100. b. b.Do not advertise the network between EastHQ and the Internet. c. Do not advertise the network between EastHQ and the West Region. d. Advertise all other attached networks. e. Disable automatic summarization. f. Disable EIGRP updates out interfaces where there are no EIGRP neighbors available. g. On EastHQ, enter the one command in the EIGRP routing process that will propagate the default and static routes to E-Branch1 and E-Branch2.
  5. 5. EastHQ(config)#router eigrp 100 EastHQ(config-router)#network EastHQ(config-router)#network EastHQ(config-router)#no auto-summary EastHQ(config-router)#ip default-network EastHQ(config)#interface serial0/1/0 EastHQ(config-if)#no eigrp 100 EastHQ(config)#interface serial0/1/1 EastHQ(config-if)#no eigrp 100 ----------------------------------------- EB1(config)#router eigrp 100 EB1(config-router)#network EB1(config-router)#network` EB1(config-router)#passive-interface fa0/0 EB1(config-router)#passive-interface fa0/1 EB1(config-router)#CTRL+Z ------------------------------------------ EB2(config)#router eigrp 100 EB2(config-router)#network EB2(config-router)#network EB2(config-router)#passive-interface fa0/0 EB2(config-router)#passive-interface fa0/1 EB2(config-router)#CTRL+ZStep 5: Modify the default EIGRP operation. a. Configure the link between EastHQ and E-Branch2 so that the correct bandwidth of 384 k/s is used in EIGRP calculations. b. Configure E-Branch1 to advertise a summary route for the subnets and to EastHQ and E-Branch2. c. Configure E-Branch2 to advertise a summary route for the subnets and to EastHQ and E-Branch1. EastHQ(config)#interface s0/0/1 EastHQ(config-if)#bandwidth 384 EastHQ(config-if)#ip bandwidth-percent eigrp 100 100 EB2(config)#interface s0/0/0 EB2(config-if)#bandwidth 384 EB2(config-if)#ip bandwidth-percent eigrp 100 100 EB1(config)#router eigrp 100 EB1(router-config)#network EB1(router-config)#end EB2(config)#router eigrp 100 EB2(router-config)#network EB2(router-config)#end
  6. 6. Step 6: Verify Full Connectivity. Although these are not scored, the following connectivity tests should be successful.• Test connectivity to the West Region.• Test connectivity to the Internet.Version 1.0Created in Packet Tracer and Marvel 1.0.1All contents are Copyright © 1992 - 2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.