• Share
  • Email
  • Embed
  • Like
  • Save
  • Private Content
Configuring nat on cisco asa
 

Configuring nat on cisco asa

on

  • 867 views

Network address translation (NAT) allows you to translate private to public addresses. ...

Network address translation (NAT) allows you to translate private to public addresses.
With CISCO ASA firewall, You can configure 2 types of NAT:
- Dynamic NAT (including PAT - port address translation)
- Static NAT

Statistics

Views

Total Views
867
Views on SlideShare
866
Embed Views
1

Actions

Likes
0
Downloads
14
Comments
0

1 Embed 1

http://www.pinterest.com 1

Accessibility

Categories

Upload Details

Uploaded via as Microsoft Word

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

    Configuring nat on cisco asa Configuring nat on cisco asa Document Transcript

    • How to Configure NAT on Cisco ASA Network address translation (NAT) allows you to translate private to public addresses. With CISCO ASA firewall, You can configure 2 types of NAT: - Dynamic NAT (including PAT - port address translation) - Static NAT Nat example (Web server must send responses to a client on public/mapped address): Dynamic NAT allows You to translate internal addresses to a predefined set or pool of public addresses You define. The "nat" command defines which internal hosts, and the "global" command defines public address range in which internal addresses will be translated. Number "1" in nat configuration defines NAT ID (number of NAT rule), and must match on "nat" and "global" command: ASA1(config)#nat (inside) 1 192.168.15.0 255.255.255.0 ASA1(config)#global (outside) 1 193.222.168.113-193.222.168.116 255.255.255.240 PAT translates a range of internal addresses to 1 public address by mapping them to a different ports: ASA1(config)#nat (inside) 1 192.168.15.0 255.255.255.0 ASA1(config)#global (outside) 1 193.222.168.113 Instead of ip address in a global command, it's possible to define word "interface". That way, the internal addresses will automatically be PAT-ed into the address of an outside inteface: ASA1(config)#nat (inside) 1 192.168.15.0 255.255.255.0
    • ASA1(config)#global (outside) 1 interface Static NAT, allows You to permanently map public ip address and port to an inside one (port forwarding). Along with that, cisco allows 1:1 NAT, or "mirroring", which translates all internal ports of a private address to the same ports on a public address (bi-directional). Of course, to enable traffic flow from the "outsude" to the "inside" interface, traffic also must be allowed with the Access control list. Port forwarding: Port forwarding of publicly available ports to an internal addresses. After configuring NAT, to enable traffic flow from outside to inside hosts, You must apply access-lists which will allow the traffic. Finally, to activate acl, bind it on a "outside" interface with the "access-group" command: ASA1(config)#static (inside,outside) tcp 209.165.201.3 http 10.2.2.28 http netmask 255.255.255.255 ASA1(config)#static (inside,outside) tcp 209.165.201.3 ftp 10.2.2.27 ftp netmask 255.255.255.255 ASA1(config)#static (inside,outside) tcp 209.165.201.3 smtp 10.2.2.29 smtpnetmask 255.255.255.255 ASA1(config)#access-list outside_in_acl extended permit tcp any host 209.165.201.3 eq http ASA1(config)#access-list outside_in_acl extended permit tcp any host 209.165.201.3 eq ftp
    • ASA1(config)#access-list outside_in_acl extended permit tcp any host 209.165.201.3 eqsmtp ASA1(config)#access-group outside_in_acl in interface outside Static 1:1nat, (every public port maped to the same internal port): ASA1(config)#static (inside,outside) 209.165.201.4 10.2.2.45 netmask 255.255.255.255 To allow traffic flow from lower security interface "outside", to higher security interface "inside", access control list must be applied. More Related Cisco ASA Tips: Site-to-Site IPSEC VPN between Two Cisco ASA 5520 How to Configure Dual ISP on Cisco ASA 5505? Cisco ASA 8.4 vs. Typical NAT/PAT Configuration Eight Commands on a Cisco ASA Security Appliance You Should Know VLAN Sub-Interfaces on Cisco ASA 5500 Firewall Configuration How to Configure Cisco ASA 5505 Firewall?