Cisco Catalyst Switch Cable, Connector, and AC Power Cord GuideThis document is a guide to cables and connectors for Catal...
Hub            Switch            Router       WorkstationHub                 Crossover      Crossover         Straight    ...
This is used in order to connect toThis is used in order to connect to 100Base-FX,           1000Base-SX,    Long100Base-F...
This is used in order to connect to StackWise ports on the rear panel of Catalyst 3750switches. Cisco StackWise technology...
This uses LC fiber-optic connector or                                        RJ-45 for 1000Base-T SFP. Part numbers:This u...
WS-X6348-RJ45V                                                        GuideWS-X6548-RJ45           4810/100 or 10/100 inli...
WS-X6501-10GEX4 1 port10-GigabitEthernetWS-X6502-10GE with    Optical   Interface                             SMF         ...
10/100 Ethernet portsWS-X5015-MT 24        10Base-FL                                MT-RJ              SMF/MMFports WS-X52...
1000Base-SX/LX) or R t5, 5e, or 6                             J-45 (for 1000Base-T)                             RJ-45     ...
Four pair Cat                          RJ-45 (10/100/1000) SFPWS-C3560G-24TS,                                   5, 5e, or ...
Cable/ConnectPart Number                   Connector Type     Cable Type            or                                    ...
RJ-45           (for Category 5, 5e, or                        10/100/1000 ports) 6 UTPWS-C2970G-24TS 2410/100/1000 and 4 ...
2 1000BASE-SX ports    (for 1000BASE-SX                       ports)WS-C2955T-12WS-C2950T-24WS-C2950T-48-SI12,            ...
Specifications                             SC    fiber-optic                             (forWS-C3508G-XL 8          GBIC ...
ports WS-X2922-XL2 10/100                                              GuideEthernet portsWS-X2922-XL-V 2                 ...
detailed specifications you can. These few points are important to know:       The 950W (PWR-950-AC), 950W DC (PWR-950-DC)...
220Vac, 16A                 Not Connected               2900W       Not Connected               220Vac, 16A               ...
CAB-7513AC= AC Power                        Cord North America                        (110Vac, 20A)                       ...
CAB-AC-2500W-US1                        250Vac           16A,                        straight-blade NEMA                  ...
CAB-AC-2500W-US1=25                           0Vac 16A, straight-blade                           NEMA 6-20 plug           ...
CAB-7513ACCatalyst 4500/4000 Series Switch Power Supplies and CablesRefer to the Power Connection Guidelines for AC-Powere...
10 foot, male 180 degree to male                                              120 degree, Category 5 telco cable 5CAB-5-M1...
5                  Slate/White                 231                 Red/Blue                    36                  Blue/Re...
20                 Slate/Yellow                646                 Violet/Blue                 1                   1121   ...
Upcoming SlideShare
Loading in …5
×

Cisco catalyst switch cable, connector, and ac power cord guide

1,588
-1

Published on

Published in: Technology, Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
1,588
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
29
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Cisco catalyst switch cable, connector, and ac power cord guide

  1. 1. Cisco Catalyst Switch Cable, Connector, and AC Power Cord GuideThis document is a guide to cables and connectors for Catalyst 6500/6000,5500/5000, and 4500/4000 series switching modules and Catalyst 2900/3500 XL,2940, 2970, 2950/2955, 3550, and 3750 series fixed-configuration switches. ACpower supplies, connectors, and cords for these switches are also covered.PrerequisitesRequirementsYou should identify the part or model number of your switch/supervisor, switchingmodule, or power supply in order to use this document effectively. Do this by visualinspection, or issue the show module command where possible.NOTE: This document is not restricted to specific software and hardware versions.ConventionsRefer to Cisco Technical Tips Conventions for more information on documentconventions.Console and Aux Port CablesDifferent Catalyst Supervisor Engines use either a rolled or a straight-through cable inorder to connect a terminal or modem to the console port. Refer to these documentsfor information on how to connect a terminal or modem to the console port ofCatalyst series switches: Connecting a Terminal to the Console Port on Catalyst Switches Connecting a Modem to the Console Port on Catalyst SwitchesAuxiliary (AUX) ports on Layer 3 (L3) switches or modules behave much the sameway as AUX ports on routers and are used to connect modems. Referto Modem-Router Connection Guide for information on how to connect a modem toan AUX port.Which RJ-45 Ethernet Cable Do I Use?A common question that concerns RJ-45 unshielded twisted pair (UTP) Ethernetcable concerns how to distinguish between rolled, straight-through, and crossovercables, and when to use them. Use the comparison guide found in theTypes of RJ-45Cabling section of Cabling Guide for Console and AUX Ports in order to see thedifference between these cables.Cables to Hubs, Switches, Routers, and WorkstationsCrossover and straight-through cables are used in order to connect switch ports orinterfaces to network devices. Consult this table in order to see when to use each ofthese cable types. Find the device in the left-hand column and match it up withanother device in the top row. The intersection of these two devices gives you thecable type used to connect them together. http://www.router-switch.com/http://blog.router-switch.com/
  2. 2. Hub Switch Router WorkstationHub Crossover Crossover Straight StraightSwitch Crossover Crossover Straight StraightRouter Straight Straight Crossover CrossoverWorkstation Straight Straight Crossover Crossover ®Note: The ports on Catalyst switches that run Cisco IOS Software (Native) can beconfigured to act as Layer 2 (L2) or Layer 3 (L3) ports. When you connect the RJ-45cable from a Layer 3 port, which acts as a router port, to other devices, use theprevious table? In summary, the cables used do not change, regardless of whetherthe port is configured to be in Layer 2 (switch port) or Layer 3 (router port) mode.Most Common Cable ConnectorsThese diagrams show some of the most common cable types and connectors used onCatalyst switches.RJ-45 RJ-21 TelcoThis is used in order to connect to 10/100or 10/100/1000 Ethernet ports and This is used in order to connect to1000Base-T Gigabit Interface Converter 10/100BASE-TX RJ-21 telco interfaces.(GBIC) or small form factor pluggable Use Category 5 UTP cables with male(SFP) GBIC ports. 10/100/1000 Ethernet RJ-21.ports must use four twisted-pair Category5, 5e or 6 cables.MT-RJ Fiber-Optic SC Fiber-Optic http://www.router-switch.com/http://blog.router-switch.com/
  3. 3. This is used in order to connect toThis is used in order to connect to 100Base-FX, 1000Base-SX, Long100Base-FX fiber-optic ports. Use Wavelength/Long Haul (LX/LH) and ZXmultimode fiber (MMF) cables with MT-RJ fiber-optic ports or GBICs. Use MMF orconnectors. single-mode fiber (SMF) fiber-optic cable.LC Fiber-Optic GigaStack This is used in order to connect toThis is used in order to connect to SFP GigaStack GBIC ports. Cisco GigaStackfiber-optic module ports. technology uses proprietary GBICs and cables.StackWise http://www.router-switch.com/http://blog.router-switch.com/
  4. 4. This is used in order to connect to StackWise ports on the rear panel of Catalyst 3750switches. Cisco StackWise technology uses proprietary connectors and cables.GBIC and SFP ConnectorsMany Catalyst switches, Supervisor Engines and switching modules have removableGigabit Interface Converters (GBICs) or small form factor pluggable (SFP)-typeconnectors. These diagrams show some of the most common GBIC and SFPconnectors used on Catalyst switches.Note: A Catalyst 2950 switch is used for demonstration purposes.1000Base-X 1000Base-TThis uses SC fiber-optic connector andMMF or SMF cable. Part numbers: This uses RJ-45 connector and cable. PartWS-G5484 (1000Base-SX GBIC) number: WS-G5483 (1000Base-T GBIC)WS-G5486 (1000Base-LX/LH GBIC)WS-G5487 (1000Base-ZX GBIC)WS-X3500-XL GigaStack GBIC SFP Module http://www.router-switch.com/http://blog.router-switch.com/
  5. 5. This uses LC fiber-optic connector or RJ-45 for 1000Base-T SFP. Part numbers:This uses Cisco Gigastack connector and GLC-T (1000Base-T SFP) GLC-SX-MMcable. Part Number: WS-X3500-XL (1000Base-SX SFP) GLC-LH-SM(GigaStack GBIC) (1000Base-LX/LH SFP) GLC-ZX-SM (1000Base-ZX)GBIC and SFP support depends on the platform and software version. Refer to thesedocuments for GigabitEthernet system requirements, as well as GBIC systemrequirements, Coarse Wave Division Multiplexer (CWDM) GBIC, Gigastack GBIC, andSFP system requirements: System Requirements to Implement Gigabit Ethernet on Catalyst Switches Catalyst GigaStack Gigabit Interface Converter Switch Compatibility Matrix 1000BASE-T GBIC Installation Notes Gigabit Interface Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Installation Information and Specifications GBIC, SFP, and Passive Devices DocumentationCatalyst 6500/6000 Switch Connectors and CablesIdentify the switch chassis and switching module part number. Use this table in orderto match up the part number with the type of connector and cable used.Note: This guide does not cover cables for the Catalyst 6000 Optical Services Module(OSM) or port adapter cables for the FlexWAN card.Refer to Optical Services Module Installation and Verification Note for OSM cablingand specifications.Refer to FlexWAN Module Port Adapter Install/Config Notes for FlexWAN portadapter cabling and specifications. Cable/ConneSwitching Module Part Cable ctor Connector TypeNumber Description Specification sWS-X6148-RJ45V Catalyst RJ-45 (for 10/100 and Category 5,WS-X6248-RJ45 6500/6000 1000Base-T ports) 5e, or 6 UTPWS-X6348-RJ45 Hardware http://www.router-switch.com/http://blog.router-switch.com/
  6. 6. WS-X6348-RJ45V GuideWS-X6548-RJ45 4810/100 or 10/100 inlinepower Ethernetports WS-X6148-GE-TXWS-X6148V-GE-TXWS-X6548-GE-TXWS-X6548V-GE-TX 4810/100/1000 or10/100/1000 inline powerEthernet ports(1000Base-T) WS-X6748-GE-TX 48 10/100/1000Ethernet ports (used withSupervisor 720 only)WS-X6516-GE-TX 16 RJ-45 (for 1000Base-T Category 5,10/100/1000 Base-T GBIC) 5e, or 6 UTPGigabit Ethernet portsWS-X6148-RJ21VWS-X6248-TELWS-X6248A-TEL RJ-21 telco (4 Category 5WS-X6348-RJ21V connectors) UTP cableWS-X6548-RJ2148 Port10/100 Ethernet portsWS-X6024-10FL-MT 2410Base-FLports WS-X6224-100FX-MT SMF/MMFWS-X6324-100FX-MM MT-RJ fiber-optic fiber-opticWS-X6324-100FX-SMWS-X6524-100FX-MM24100Base-FX portsWS-X6416-GE-MT 16 MMF100Base-FX Gigabit MT-RJ fiber-optic fiber-opticEthernet ports (1000Mbps)WS-X6408-GBIC RJ-45 (for 1000Base-T Category 5,WS-X6408A-GBIC GBIC) 5e, 6 UTPWS-X6416-GBICWS-X6516-GBIC SCWS-X6516A-GBIC fiber-optic1(1000BaseSX MMFWS-X6816-GBIC8 or 16 /LX/ZX and CWDM fiber-opticGBIC module slots GBICs) http://www.router-switch.com/http://blog.router-switch.com/
  7. 7. WS-X6501-10GEX4 1 port10-GigabitEthernetWS-X6502-10GE with Optical Interface SMF orModule (OIM) 1-port dispersion-shi SC fiber-optic10-Gigabit fted SMFEthernetWS-X6704-10GE 4 fiber-opticport 10-Gigabit Ethernet(used with Supervisor 720only) RJ-45 (for 1000Base-T Category 5,WS-X6724-SFP 24 SFP SFP) 5e, 6 UTPmodule slots (used with LC fiber-optic (forSupervisor 720 only) SMF/MMF 1000Base-SX/LX/ZX SFP fiber-optic s)1 LX/LH GBICs require a mode-conditioning patch cord between the GBIC and MMF.Refer to the Mode-Conditioning Patch Cord section of the document Connector andCable Specifications for more information.Catalyst 5500/5000 Connectors and CablesIdentify the switching module part number. Use this table in order to match up thepart number with the type of connector and cable used.Note: This guide does not cover Catalyst 5000 Fiber Distributed Data Interface (FDDI)and Copper Distributed Data Interface (CDDI) cables, Catalyst 5000 ATM cables, orCatalyst 5000 Token Ring cables. Refer to Installation Preparationfor cabling andspecifications for these modules. Cable/Conne Connector CableSwitching Module Part Number ctor Type Description SpecificationsWS-X5013 WS-X501424 or 4810-Base-T Ethernetports WS-X5113 WS-X5223 12 or24 100Base-TX Ethernet Category 3 or 5ports WS-X5203 WS-X5213A 12 RJ-45 UTP cable1 Catalyst 500010/100 Ethernet ports WS-X5224WS-X5225R HardwareWS-X5234-RJ45J45 24 10/100 GuideEthernet portsWS-X5012 WS-X5012A Category 3 or 5WS-X502048 Port 10Base-T RJ-21 telco UTP cable1Ethernet ports WS-X5239-RJ2148 http://www.router-switch.com/http://blog.router-switch.com/
  8. 8. 10/100 Ethernet portsWS-X5015-MT 24 10Base-FL MT-RJ SMF/MMFports WS-X5236-FX-MT WS-X523 fiber-optic fiber-optic7-FX-MT 24 100Base-FX SC fiber-opticWS-X5114 WS-X5201 SMF/MMF (forWS-X5201R12 100Base-FX ports fiber-optic 100Base-FX) SC fiber-opticWS-X5403 3 port GBIC modules (for SMF/MMF2fiber-slotsWS-X5410 9 GBIC module 1000BaseSX/L opticslots X/ZX GBICs)1 Category 3 UTP cable can transmit data at speeds of up to 10 Mbps and therefore isonly used for 10 Mbps network devices. Catalyst 5000 10Base-T telco switchingmodules can use Category 3 cable, but Category 5 cable is required for all other10/100 Base-TX switching modules.2 LX/LH GBICs require a mode-conditioning patch cord between the GBIC and MMF.Refer to the Mode-Conditioning Patch Cord section of the document Connector andCable Specifications for more information.Catalyst 4500/4000 Switch Connectors and CablesRefer to Module Overview for the detailed specification for the Catalyst 4500switching modules.Refer to Catalyst 4000 Switching Modules for the detailed specification for theCatalyst 4000 switching modules.Catalyst 3750 Connectors and CablesIdentify the switch chassis part number. Use this table in order to match up the partnumber with the type of connector and cable used.Note: The Catalyst 3750 switch ships with a 0.5-meter StackWise cable that you canuse in order to connect the StackWise ports on the rear panel. You can also orderthese StackWise cables from your Cisco sales representative: CAB-STACK-50CM= (0.5-meter cable) CAB-STACK-1M= (1-meter cable) CAB-STACK-3M= (3-meter cable) Cable/ConnecPart Number Connector Type Cable Type tor SpecificationsWS-C3750-24TS RJ-45 (for 10/100 Category 5, 5e,WS-C3750-48TS 24 or 48 ports) or 6 UTP cable Catalyst 3750 Hardware10/100 Ethernet ports and SFP: LC fiber-optic SFP: SMF/MMF Guide2 or 4 SFP module slots (for fiber-optic, orCa http://www.router-switch.com/http://blog.router-switch.com/
  9. 9. 1000Base-SX/LX) or R t5, 5e, or 6 J-45 (for 1000Base-T) RJ-45 (for Category 5, 5e, 10/100/1000 ports) or 6 UTP cableWS-C3750G-24TS2410/100/1000 and 4 SFP SFP: LC fiber-optic SFP: SMF/MMFmodule slots (for fiber-optic, orCa 1000Base-SX/LX) or R t5, 5e, or 6 J-45 (for 1000Base-T)WS-C3750G-24T24 10/100/ Category 5, 5e, RJ-451000 Ethernet ports or 6 UTP cable SFP: LC fiber-optic SFP: SMF/MMFWS-C3750G-12S 12 SFP (for fiber-optic, orCamodule slots 1000Base-SX/LX) or R t5, 5e, or 6 J-45 (for 1000Base-T)Catalyst 3560/3560E Connectors and CablesIdentify the switch chassis part number. Use this table in order to match up the partnumber with the type of connector and cable used. Cable/ConnectorPart Number Connector Type Cable Type Specifications Two pair Cat RJ-45 (10/100) 5, 5e, or 6 UTP Four pair Cat Catalyst 3560WS-C3560-8PC RJ-45 (10/100/1000) 5, 5e, or 6 Hardware UTP GuideAlso refer to Cisco Small LC Form-Factor SFP (100Base-FX/LX/BX) Fiber-optic Pluggable (SFP) SMF/MMF Transceiver Two pair Cat Modules RJ-45 (10/100) SFPWS-C3560-24TS, 5, 5e, or 6 Maintenance and (1000Base-T)WS-C3560-48TS, UTP Troubleshooting.WS-C3560-24PS, LCWS-C3560-48PS SFP Fiber-optic (1000Base-LH/SX/ZX) SMF/MMF http://www.router-switch.com/http://blog.router-switch.com/
  10. 10. Four pair Cat RJ-45 (10/100/1000) SFPWS-C3560G-24TS, 5, 5e, or 6 (1000Base-T)WS-C3560G-48TS, UTPWS-C3560G-24PS, LCWS-C3560G-48PS SFP Fiber-optic (1000Base-LH/SX/ZX) SMF/MMF Four pair Cat RJ-45 (10/100/1000) SFP 5, 5e, or 6 (1000Base-T) UTPWS-C3560E-24TD,WS-C3560E-24PD, LCWS-C3560E-48TD, SFP (100Base-FX, Fiber-opticWS-C3560E-48PD, 1000Base-LH/SX/ZX) SMF/MMFWS-C3560E-48PD-F SC X2 Based Fiber-optic (10GBASE-SR/LR/ER) SMF/MMFNote: Cisco 3560 Series Purchasing:http://www.router-switch.com/Price-cisco-switches-cisco-switch-catalyst-3560_c22SFP Module Patch CableThe Catalyst 3560 switch supports the SFP module patch cable, a 1/2 meter, copper,passive cable with SFP module connectors at each end. The patch cable can connecttwo Catalyst 3560 switches in a cascaded configuration.Part Number Description Cisco Catalyst 3560 SFP InterconnectCAB-SFP-50CM= Cable (50 dcm)Catalyst 3550 Connectors and CablesIdentify the switch chassis part number. Use this table in order to match up the partnumber with the type of connector and cable used.Note: Some Catalyst 3550 switches support the GigaStack GBIC, which requires aCisco proprietary cable of either CAB-GS-50CM (0.5-meter cable) or CAB-GS-1M(1-meter cable). http://www.router-switch.com/http://blog.router-switch.com/
  11. 11. Cable/ConnectPart Number Connector Type Cable Type or SpecificationsWS-C3550-12T 10 RJ-45 (for10/100/1000 Ethernet ports 10/100 orand 2 GBIC module 10/100 inline Category 5, 5e, 6slots WS-C3550-12G 2 power or UTP10/100/1000 Ethernet ports 10/100/1000and 10 GBIC module ports)slots WS-C3550-24-SMI,WS-C3550-24-DC-SMIWS-C3550-48-SMI GBIC: RJ-45 forWS-C3550-24-EMI 1000Base-TWS-C3550-48-EMI 24 or 48 GBIC or SC GBIC: Cat 5, 5e, 610/100 Ethernet ports and 2 fiber-optic (for UTP orMMF/SMFGBIC module 1000Base-SX/LX/ fiber-opticorGigaStslots WS-C3550-24PWR-SMI ZX and CWDM ack cableWS-C3550-24PWR-EMI2410 GBICs) orGigasta Catalyst 3550/100 inline-power Ethernet ck GBIC Hardwareports and 2 GBIC module Guideslots MT-RJ fiber-optic (for MMF fiber-optic 100Base-FX ports)WS-C3550-24-FX-SMI24 GBIC: RJ-45 for100Base-FX ports and 2 GBIC 1000Base-Tmodule slots GBIC or SC GBIC: Cat 5, 5e, 6 fiber-optic (for UTP orMMF/SMF 1000Base-SX/LX/ fiber-opticorGigaSt ZX and CWDM ack cable GBICs) orGigasta ck GBICCatalyst 2970 Connectors and Cables Cable/ConnectorPart Number Connector Type Cable Type SpecificationsWS-C2970G-24T 24 Category 5, 5e, or Catalyst 297010/100/1000 RJ-45 6 UTP Hardware GuideEthernet http://www.router-switch.com/http://blog.router-switch.com/
  12. 12. RJ-45 (for Category 5, 5e, or 10/100/1000 ports) 6 UTPWS-C2970G-24TS 2410/100/1000 and 4 SFP: RJ-45 (for SFP: Cat5, 5e, or 6SFP module slots 1000Base-T) orLC UTPor SMF/MMF fiber-optic (for fiber-optic 1000Base-SX/LX/ZX)Catalyst 2950/2955 Connectors and CablesIdentify the switch chassis part number. Use this table in order to match up the partnumber with the type of connector and cable used.Note: This guide does not cover the Catalyst 2950 Long-Reach Ethernet (LRE)Switches. Refer to Long-Reach Ethernet Products for more information on cablingand specifications.Note: Some Catalyst 2950 switches support the GigaStack GBIC, which requires aCisco proprietary cable of either CAB-GS-50CM (0.5-meter cable) or CAB-GS-1M(1-meter cable). Cable/ConnectoPart Number Connector Type Cable Type r SpecificationsWS-C2950-12 andWS-C2950-24 12 or Category 5, 5e, or 6 RJ-4524 10/100 Ethernet UTP cableportsWS-C2955C-12 and RJ-45 (for 10/100 Category 5, 5e, or 6WS-C2950C-24 12 or ports) UTP cable24 10/100 Ethernetports and MT-RJ fiber-optic MMF fiber-optic2 100BASE-FX ports RJ-45 (for 10/100 Category 5, 5e, or 6 Catalyst 2950WS-C2950G-12-EI, ports) UTP HardwareWS-C2950G-24-EI, GuideCatalyst GBIC: RJ-45 forWS-C2950G-24-EI-DC 2955 Hardware 1000Base-T, and Guide GBIC or SC GBIC: Cat 5, 5e, 6WS-C2950G-48-EI 12, fiber-optic (for UTP orMMF/SMF24, or 48 10/100 1000Base-SX/LX/Z fiber-opticorGigaStacEthernet ports and 2 X and CWDM k cableGBIC module slots GBICs)or Gigastack GBICWS-C2950SX-24 and RJ-45 (for 10/100 Category 5, 5e, or 6WS-C2950SX-48-SI 24 ports) UTPor 48 10/100Ethernet ports and MT-RJ fiber-optic MMF/SMF fiber-optic http://www.router-switch.com/http://blog.router-switch.com/
  13. 13. 2 1000BASE-SX ports (for 1000BASE-SX ports)WS-C2955T-12WS-C2950T-24WS-C2950T-48-SI12, Category 5, 5e, or 624 or 48 10/100 RJ-45 UTP cableEthernet ports and2 10/100/1000Ethernet portsWS-C2955S-12 12 RJ-45 (for 10/100 Category 5, 5e, or 610/100 Ethernet ports) UTPports and 2100Base-LX ports MT-RJ fiber-optic SMF fiber-opticCatalyst 2940 Connectors and CablesIdentify the switch chassis part number. Use this table in order to match up the partnumber with the type of connector and cable used. Cable/ConnectorPart Number Connector Type Cable Type SpecificationsWS-C2940-8TT-S8 10/100 Category 5, 5e, orEthernet ports and 1 RJ-45 6 UTP10/100/1000 port Category 5, 5e, or RJ-45 6 UTP Catalyst 2940WS-C2940-8TF-S8 10/100 Hardware GuideEthernet ports, 1 MT-RJ fiber-optic MMF fiber-optic100BASE-FX port, and 1 SFP: RJ-45 (for SFP: Cat5, 5e, orSFP module slot 1000Base-T)or LC 6 fiber-optic (for UTP orSMF/MMF 1000Base-X) fiber-opticCatalyst 2900/3500 XL Connectors and CablesIdentify the switch chassis or expansion module part number. Use this table in orderto match up the part number with the type of connector and cable used.Note: This guide does not cover the WS-C2912-LRE-XL or WS-C2912-LRE-XL switches.Refer to theLong-Range Ethernet Ports section of Product Overview (Catalyst 2900Series XL switches) for more information on cabling and specifications.Note: Some Catalyst 3500XL switches support the GigaStack GBIC, which requires aCisco proprietary cable of either CAB-GS-50CM or CAB-GS-1M.Catalyst 2900/3500XL Switches Cable/ConnecSwitch Chassis Part Number Connector Type Cable Description tor http://www.router-switch.com/http://blog.router-switch.com/
  14. 14. Specifications SC fiber-optic (forWS-C3508G-XL 8 GBIC 1000Base-SX/LX MMF/SMFmodule slots /ZX fiber-optic GBICs) orGigasta ck GBIC RJ-45 (for Category 5 UTPWS-C3512-XL WS-C3524-XL 10/100 ports) CatalystWS-C3524-PWR-XL 3500XL GBIC: SCWS-C3548-XL 12, 24 or 48 fiber-optic (for Hardware10/100 or 10/100 inline 1000Base-SX/LX GBIC: MMF/SMF GuideCatalystpower Ethernet ports and 2 /ZX fiber-optic orGigaSt 2900XLGBIC module slots ack cable Hardware GBICs) orGigasta Guide ck GBICWS-C2912-XLWS-C2924-XL 12 or 24 RJ-45 Category 5 UTP10/100 Ethernet portsWS-C2924C-XL 22 10/100 SC fiber-opticEthernet ports and 2 (for 100Base-FX MMF fiber-optic100Base-FX ports ports)Catalyst 2900XL Switches with Expansion Slots Cable/ConnecSwitch Chassis Part Number Connector Type Cable Description tor SpecificationsWS-C2924M-XL 24 10/100Ethernet ports and 2 RJ-45 Category 5 UTP Catalystexpansion slots 2900XLWS-C2912MF-XL12 SC fiber-optic Hardware100Base-FX ports and 2 (for 100Base-FX MMF fiber-optic Guideexpansion slots ports)Catalyst 2900XL Expansion Modules Cable/ConnecSwitch Chassis Part Number Connector Type Cable Description tor SpecificationsWS-X2914-XL CatalystWS-X2914-XL-V 4 10/100 RJ-45 Category 5 UTP 2900XLEthernet Hardware http://www.router-switch.com/http://blog.router-switch.com/
  15. 15. ports WS-X2922-XL2 10/100 GuideEthernet portsWS-X2922-XL-V 2 SC fiber-optic100Base-FX (for 100 MMF fiber-opticportsWS-X2924-XL-V4 100Ba Base-FX)se-FX ports SC fiber-opticWS-X2931-XL 1 GBIC module (for SX/LX MMF fiber-opticslot GBICs) RJ-45 (forWS-X2932-XL 1 GBIC module 1000Base-Tslot GBIC) RJ-45 (forWS-X2951-XL 1 ATM-OC-3 Category 5 UTP ATM-OC-3) SC fiber-opticWS-X2961-XL 1 ATM-OC-3 MMF fiber-optic (for ATM-OC-3)WS-X2971-XL WS-X2972-XL 1 SC fiber-optic SMF fiber-opticATM-OC-3 (for ATM-OC-3)AC Power Supplies, Connectors, and Cords for Catalyst SwitchesIn this section you see the summary of AC power supplies, power connectors, andcords for Catalyst 6500/6000, 5500/5000 and 4500/4000 series, and Catalyst 3750,2950, 2940, and 2900/3500XL series switches. Refer to the Power InstallationGuidelines in the tables that correspond in the next section for international powerrequirements, DC power requirements, and other technical specifications.Different Modules require different amount of power. Inline Power modules suppliesthe power to the IP phones. Cisco has inline power module to power the IP phones.You have to choose the correct power supply in order to support the various linecards, modules and Supervisor Engines on the switch. Cisco offers a tool calledthe Cisco Power calculatorwhich can be used in order to choose the correct powersupply for your switch. Launch the Cisco Power calculatorand fill out the Productfamily, Supervisor Engine, Input voltage, line cards and the number of PoE devices. IPphones are the example for PoE devices and most of the IP phones belong to IEEE802.3af Device - Class 2 (7W). Then the power calculator shows the results ofdifferent choices of Power Supplies. From that you can choose the required powersupply. The power supplies successfully operate at their greatest capacity if the inputvoltage is between 200 and 240 volts AC.Catalyst 6500/6000 Series Switch Power Supplies and CablesThis table is a quick reference for the available power supplies and cables in NorthAmerican standard. Refer toCatalyst 6500 Power supply specifications for the http://www.router-switch.com/http://blog.router-switch.com/
  16. 16. detailed specifications you can. These few points are important to know: The 950W (PWR-950-AC), 950W DC (PWR-950-DC) and 1400W AC (PWR-1400-AC) are used only with the Catalyst 6503 and Catalyst 6503-E Switches. The Power supplies 1000W and 1300W can be used only with Catalyst 6506, 6509, and 6509-NEB-A switches. The Supervisor Engines SUP32 and SUP720 are incompatible when 1000W and 1300W power supplies are used. With a fully populated Catalyst 6513 switch, two 2500 W power supplies are not fully redundant. If you operate the 2500 W power supply at the low range input (100 to 120 VAC), it is not redundant in a fully populated Catalyst 6509, Catalyst 6509-E, Catalyst 6509-NEB, or Catalyst 6509-NEB-A switch. The Power supplies 2500W, 2700W, and 3000W can operate at two different voltage levels (110Vac and 220Vac). The Power supply output depends on the supplied input AC power. This table shows the power ouput: Power Output at Power Output at Power Supply 110Vac, 16A 220Vac, 16A 2500W 1300W 2500W 2700W 1350W 2700W 3000W 1400W 3000W The AC power cords are hardwired to the 4000W Power supplies (WS-CAC-4000W-US=). It supports only NEMA L6-30. The 6000W power supply cannot be installed in the Catalyst 6503, Catalyst 6503-E, and Catalyst 6504-E switch chassis. When 6000W power supply is used with the chassis Catalyst 6506, 6509, 6509-NEB, and 6509-NEB-A, it operates at 4000W maximum output. It operates at 6000W maximum output when it is used with Catalyst 6506-E, 6509-E, and 6513. 6000W power supply has two AC Power inputs. These are the various combinations of AC inputs and the corresponding net power output: 6000W Power Supply Power Options Net Power Supply AC Input 1 AC Input 2 Output 110Vac, 16A Not Connected No Power Output Not Connected 110Vac, 16A No Power Output 110Vac, 16A 110Vac, 16A 2900W http://www.router-switch.com/http://blog.router-switch.com/
  17. 17. 220Vac, 16A Not Connected 2900W Not Connected 220Vac, 16A 2900W 110Vac, 16A 220Vac, 16A 2900W 220Vac, 16A 110Vac, 16A 2900W 220Vac, 16A 220Vac, 16A 6000W Note: If you have 110Vac power inputs, you have to connect both the AC inputs of the 6000W power supply in order to power on the switch. The Catalyst 6500 series switches allow you to mix AC-input and DC-input power supplies in the same chassis.The modules have different power requirements, and some configurations requiremore power than a single power supply can provide. The power managementfeature allows you to power all installed modules with two power supplies. But,redundancy is not supported in this configuration because the total power drawnfrom both power supplies is at no time greater than the capability of one supply.Refer the Power Management and Environmental Monitoring of the Catalyst 6500Software Configuration Guide for the detailed explanation of Power redundancy.Note: This document does not discuss the total power available with the currentlyshipped power supplies for Catalyst 6500/6000 series switches or the amount drawnfrom each Catalyst 6500/6000 series line card. Refer to the documentPowerManagement for Catalyst 6000 Series Switches for this information.Catalyst 6500/6000 Power InstallatiPower Supply Part Power Cord Part Connector Type onNumber Number Guideline sPWR-950-AC 950W power CAB-7KAC-15 AC Powersupply WS-CAC-1000W10 Cord North America, 15A00W power supply Catalyst 6500/600 0 CAB-7513AC AC PowerWS-CAC-1300W1300W Cord North AmericaPower Supply (110Vac, 20A) http://www.router-switch.com/http://blog.router-switch.com/
  18. 18. CAB-7513AC= AC Power Cord North America (110Vac, 20A) CAB-AC-2500W-US1= 250Vac 16A,PWR-1400-AC 1400W straight-blade NEMAPower Supply 6-20 plug CAB-AC-C6K-TWLK= 250Vac 16A, twist-lock NEMA L6-20 plug CAB-7513AC AC Power Cord North America (110Vac, 20A) CAB-AC-2500W-US1 250Vac 16A,WS-CAC-2500W2500W straight-blade NEMAAC Power Supply 6-20 plug CAB-AC-C6K-TWLK 250Vac 16A, twist-lock NEMA L6-20 plug CAB-7513AC AC PowerPWR-2700-AC/42700W Cord North AmericaAC Power Supply (110Vac, 20A) http://www.router-switch.com/http://blog.router-switch.com/
  19. 19. CAB-AC-2500W-US1 250Vac 16A, straight-blade NEMA 6-20 plug CAB-AC-C6K-TWLK 250Vac 16A, twist-lock NEMA L6-20 plug CAB-7513AC=110Vac 20A, NEMA 5-20 plug CAB-AC-2500W-US1=25WS-CAC-3000W3000 W 0Vac 16A, straight-bladeAC-input power supply NEMA 6-20 plug CAB-AC-C6K-TWLK=250V ac 16A, twist-lock NEMA L6-20 plug Cable-attached to theWS-CAC-4000W-US4000 power supply 250VacW AC Power Supply 30AWS-CAC-6000W6000W CAB-7513AC=110VacAC Power supply 20A, NEMA 5-20 plug http://www.router-switch.com/http://blog.router-switch.com/
  20. 20. CAB-AC-2500W-US1=25 0Vac 16A, straight-blade NEMA 6-20 plug CAB-AC-C6K-TWLK=250V ac 16A, twist-lock NEMA L6-20 plugCatalyst 5500/5000 Series Switch Power Supplies and CablesThis table has a quick reference for the available power supplies and the Power cordpart number.Catalyst 5002, 5505, 5500, and 5509 PowerPower Supply Part Power Cord Connector Type InstallationNumber Part Number GuidelinesWS-C5008B(Catalyst CAB-7KAC5002 and 5505)WS-C5508(Catalyst Catalyst CAB-7513AC5500) 5500/5000WS-C5518(Catalyst CAB-7KAC5509) http://www.router-switch.com/http://blog.router-switch.com/
  21. 21. CAB-7513ACCatalyst 4500/4000 Series Switch Power Supplies and CablesRefer to the Power Connection Guidelines for AC-Powered Systems sectionin Catalyst 4500 Series Hardware Installation Guide - Preparing for Installation for thelist of Power supplies, cables and the corresponding part numbers.Refer to Catalyst 4000 Series Installation Guide - Site Planning for the list of Catalyst4000 Power supplies, cables and the corresponding part numbers.Catalyst 2900/3500XL, 2940, 2950, 3550 and 3750 Series Switch Power Suppliesand CablesCatalyst 2900/3500, 2940, 2950, 3550 and 3750 switches require standard 110V, 15Amp AC input Power. Refer to these Hardware Installation Guides for the detailedpower specifications: Catalyst 3750 Switch Hardware Installation Guide Catalyst 3550 Multilayer Switch Hardware Installation Guide Catalyst 2950 Switch Hardware Installation GuideCatalyst 2900/3500XL, 2940, 2950, 3550 and 3750 Power PowerPower Supply Part Cord Part Connector Type InstallationNumber Number GuidelinesInternalnon-replaceable AC CAB-AC= N/Apower supplyRJ-21 to RJ-45 Pin-Out PatternAll Catalyst family 10/100TX telco switching modules incorporate industry-standardRJ-21 connectors and require compatible Category 5 cabling systems to achieve 100Mbps data rates.Category 5 telco cables can be ordered directly from Cisco. Refer to Cisco.com forordering information. This is the information on Cisco part numbers.Model Number Description http://www.router-switch.com/http://blog.router-switch.com/
  22. 22. 10 foot, male 180 degree to male 120 degree, Category 5 telco cable 5CAB-5-M180M120-10= CAB-5-M180M120-5= foot, male 180 degree to male 120 degree, Category 5 telco cable 10 foot, male 120 degree to male 120 degree, Category 5 telco cable 5CAB-5-M120M120-10= CAB-5-M120M120-5= foot, male 120 degree to male 120 degree, Category 5 telco cable 10 foot, male 120 degree to (12) RJ-45s, Category 5 telco cable 5CAB-5-M120HYD-10= CAB-5-M120HYD-5= foot, male 120 degree to (12) RJ-45s, Category 5 telco cableThis table shows the pin-out pattern used on Catalyst 10/100TX (and 10BaseT) RJ-21switching modules.RJ-21 Pin RJ-45 Pin Wire Color Port NumberNumber Number26 White/Blue 1 11 Blue/White 227 White/Orange 32 Orange/White 628 White/Green 1 23 Green/White 229 White/Brown 34 Brown/White 630 White/Slate 1 3 http://www.router-switch.com/http://blog.router-switch.com/
  23. 23. 5 Slate/White 231 Red/Blue 36 Blue/Red 632 Red/Orange 1 47 Orange/Red 233 Red/Green 38 Green/Red 634 Red/Brown 1 59 Brown/Red 235 Red/Slate 310 Slate/Red 636 Black/Blue 1 611 Blue/Black 237 Black/Orange 312 Orange/Black 638 Black/Green 1 713 Green/Black 239 Black/Brown 314 Brown/Black 640 Black/Slate 1 815 Slate/Black 241 Yellow/Blue 316 Blue/Yellow 642 Yellow/Orange 1 917 Orange/Yellow 243 Yellow/Green 318 Green/Yellow 644 Yellow/Brown 1 1019 Brown/Yellow 245 Yellow/Slate 3 http://www.router-switch.com/http://blog.router-switch.com/
  24. 24. 20 Slate/Yellow 646 Violet/Blue 1 1121 Blue/Violet 247 Violet/Orange 322 Orange/Violet 648 Violet/Green 1 1223 Green/Violet 249 Violet/Brown 324 Brown/Violet 650 Violet/Slate NA NA25 Slate/Violet NA NAMore Notes: Cisco Hardware Purchasing---Router-switch.com, the World’s LeadingCisco Supplier http://www.router-switch.com/http://blog.router-switch.com/

×