Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces
Upcoming SlideShare
Loading in...5
×
 

Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces

on

  • 817 views

Huawei S5700 Layer 3 switch can replace a router to implement communication between VLANs using VLANIF interfaces. Stay with us!

Huawei S5700 Layer 3 switch can replace a router to implement communication between VLANs using VLANIF interfaces. Stay with us!

Statistics

Views

Total Views
817
Slideshare-icon Views on SlideShare
698
Embed Views
119

Actions

Likes
0
Downloads
33
Comments
0

2 Embeds 119

http://www.slideee.com 67
http://www.ipmax.it 52

Accessibility

Categories

Upload Details

Uploaded via as Adobe PDF

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

    Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces Huawei switch how to - implementing inter-vlan communication using VLANIF interfaces Presentation Transcript

    • HUAWEI QUIDWAY S5700 HOW-TO IMPLEMENTING INTER-VLAN COMMUNICATION USING VLANIF INTERFACES www.ipmax.it
    • GENERAL INFOS AND APPLICATION ENVIRONMENT S5700 Layer 3 switch can replace a router to implement communication between VLANs using VLANIF interfaces. Describing this brief procedure we will assume that departments of an enterprise are located on different network segments and use the same services, such as Internet access and VoIP. The departments are in different VLANs, so inter-VLAN communication must be implemented. In this semplified network environment, as shown in the picture, Department 1 and Department 2 use the same service, but they belong to different VLANs (vlan 10 and vlan 20) and network segments. Users in Department 1 and Department 2 need to communicate with each other. SwitchA SwitchB
    • CREATING VLANS ON THE SWITCHES FOR DIFFERENT DEPARTMENTS <SwitchB> system-view [SwitchB] vlan batch 10 20 1. Create vlans on SwitchB Enter the configuration view Create vlan 10 and vlan 20 2. Create vlans on SwitchA <SwitchA> system-view [SwitchA] vlan batch 10 20 Enter the configuration view Create vlan 10 and vlan 20
    • ADDING LAYER 2 INTERFACES TO THE VLANS (1) 3. Add layer 2 interfaces to vlans of SwitchB [SwitchB] interface gigabitethernet 0/0/1 [SwitchB-GigabitEthernet0/0/1] port link-type trunk [SwitchB-GigabitEthernet0/0/1] port trunk allow-pass vlan 10 20 [SwitchB-GigabitEthernet0/0/1] quit Enter the interface view Configure the port type Configure the vlans for the port Exit the interface view
    • ADDING LAYER 2 INTERFACES TO THE VLANS (2) [SwitchA] interface gigabitethernet 0/0/1 [SwitchA-GigabitEthernet0/0/1] port link-type trunk [SwitchA-GigabitEthernet0/0/1] port trunk allow-pass vlan 10 20 [SwitchA-GigabitEthernet0/0/1] quit [SwitchA] interface gigabitethernet 0/0/2 [SwitchA-GigabitEthernet0/0/2] port link-type access [SwitchA-GigabitEthernet0/0/2] port default vlan 10 [SwitchA-GigabitEthernet0/0/2] quit [SwitchA] interface gigabitethernet 0/0/3 [SwitchA-GigabitEthernet0/0/3] port link-type access [SwitchA-GigabitEthernet0/0/3] port default vlan 20 [SwitchA-GigabitEthernet0/0/3] quit 4. Add layer 2 interfaces to vlans of SwitchA Enter the interface view Configure the port type Configure the vlans for the port Exit the interface view
    • CREATING VLANIF INTERFACES AND CONFIGURING IP ADDRESSES ON LAYER 3 SWITCH (SWITCHB) 5. Create vlanif interfaces and assign IP address on SwitchB [SwitchB] interface vlanif 10 [SwitchB-Vlanif10] ip address 10.10.10.1 24 [SwitchB-Vlanif10] quit [SwitchB] interface vlanif 20 [SwitchB-Vlanif20] ip address 20.20.20.1 24 [SwitchB-Vlanif20] quit Create the vlanif and enter the vlanif view Exit the vlanif view Assign the IP address to the vlanif
    • CHECKING THE CONFIGURATION 6. Check the configuration on SwitchB [SwitchB] display current configuration # sysname SwitchB # vlan batch 10 20 # interface Vlanif10 ip address 10.10.10.1 255.255.255.0 # interface Vlanif20 ip address 20.20.20.1 255.255.255.0 # interface GigabitEthernet0/0/1 port link-type trunk port trunk allow-pass vlan 10 20 # return
    • CHECKING THE CONFIGURATION 7. Check the configuration on SwitchA [SwitchA] display current configuration # sysname SwitchA # vlan batch 10 20 # interface GigabitEthernet0/0/1 port link-type trunk port trunk allow-pass vlan 10 20 # interface GigabitEthernet0/0/2 port link-type access port default vlan 10 # interface GigabitEthernet0/0/3 port link-type access port default vlan 20 # return
    • MORE NEEDS? See hints on www.ipmax.it Or email us your questions to info_ipmax@ipmax.it You can buy our Remote Support assistance (1h, 4hs or 8hs pack) via PAYPAL by using your Teamviewer account. Contact us for any info!
    • IPMAX IPMAX is a Huawei GOLD Partner in Italy. IPMAX is the ideal partner for companies seeking quality in products and services. IPMAX guarantees method and professionalism to support its customers in selecting technologies with the best quality / price ratio, in the design, installation, commissioning and operation. IPMAX srl Via Ponchielli, 4 20063 Cernusco sul Naviglio (MI) – Italy +39 02 9290 9171