40120140504005

214 views

Published on

Published in: Technology, Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
214
On SlideShare
0
From Embeds
0
Number of Embeds
3
Actions
Shares
0
Downloads
2
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

40120140504005

  1. 1. International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 – 6464(Print), ISSN 0976 – 6472(Online), Volume 5, Issue 4, April (2014), pp. 36-42 © IAEME 36 EMBEDDED BASED ROBOTIC VEHICLE PROTECTION USING STISIM SOFTWARE Mr. Sarthak Pareek B.Tech Anand International College of Engineering Jaipur, Rajasthan ABSTRACT The Project mainly focuses on the design the project for a robotic Vehicle Protection with Embedded Technology and stisim software which is a driving simulator. In this project there Are two sections, one is a vehicle unit another one is a monitoring unit using stisim software. Temperature is measured with the help of temperature sensor. Fuel Level measurement using Float. That sensor’s output is given to the amplifier unit. After the amplification this output is given to the ATMEGA controller. Speed measurement using proximity sensor. This sensor’s output is given to ATMEGA controller via (Signal Conditioning Unit) SCU. ATMEGA calculate the speed from this signal. If the vehicles have very high speed immediately turn off the vehicle by relay circuit. Here we used flash type reprogrammable controller. In the event of Accident ATMEGA controller transmits all these signals to the (personnel computer) PC via (Global System for Mobile communication) GSM MODEM. Other unit is a monitoring unit.GSM MODEM will receive those signals where the PC act as the Police station server. In case of accident some voice sound can be generated in the PC for attention. RS 232 is a serial communication cable. All sensed parameters are displayed in the Police station server. If vehicle is theft means we can locate the vehicle with the help of (Global Positioning system) GPS by using Internet Maps. And also we can stop the vehicle with the help of relay. This project is helpful for Police investigation purposes. Now to have its complete safety it should be free from accidents too which can be prevented with the help of driving simulator. The simulator starting from what is happening in the real-world and developing software for it; not from developing software and then trying to apply it to the real-world. Simulator software is physically realistic, that allows one to get the data and driving behavior they need, and that produces evidence based results. New driving simulator research offers to help old and new drivers to stay safe. stisim drive asserted its driving simulation software is the best for it this software offer many benefits. INDEX TERMS: ATMEGA, STSIM, GPS. INTERNATIONAL JOURNAL OF ELECTRONICS AND COMMUNICATION ENGINEERING & TECHNOLOGY (IJECET) ISSN 0976 – 6464(Print) ISSN 0976 – 6472(Online) Volume 5, Issue 4, April (2014), pp. 36-42 © IAEME: www.iaeme.com/ijecet.asp Journal Impact Factor (2014): 7.2836 (Calculated by GISI) www.jifactor.com IJECET © I A E M E
  2. 2. International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 – 6464(Print), ISSN 0976 – 6472(Online), Volume 5, Issue 4, April (2014), pp. 36-42 © IAEME 37 I. INTRODUCTION Present industry is increasingly shifting towards automation. The principle component of today’s industrial automation is programmable robots. In order to aid the tedious work and serve to the mankind, today there is a general tendency to develop an intelligent operation. Road accidents and rear end crashing are human tragedy. They involve high human suffering and monetary cost in terms of untimely deaths injuries and loss of potential income. Although we have undertaken many initiatives and are implementing various road safety programs, During the year 2010, there were close to 5 lakhs road accidents in India, which resulted in more than 1.3 lakh deaths and inflicted injuries on 5.2 lakh person these numbers translate into one road accident every minute and one road accident deaths every 4 minutes unfortunately more than half the victims are in the economically active age group of 25-65 years. It means that In New Delhi, the capital of India, the frequency of traffic collisions is 40 times higher than the rate in London, the capital of the United Kingdom. Many a countries have curbed the menace of road accidents by adopting a multipronged approach to road safety that encompasses broad range of measures such as, traffic management, design and quality of road infrastructure, application of intelligent transport systems, safer vehicles, law enforcement etc. The Government alone cannot tackle road safety problems. There is a need for very active involvement of all stack- holders to promote policy reform and implementation of road safety measures. This Project Concern Different sensor like Vibration, Temperature, Speed, Level and also Limit switches those signals fed to ATMEGA. ATMEGA Microcontroller is the heart of the device which handles all the sub devices connected across it. the use of the driving simulation is that it provides the real time experience for the drivers. The focus of the Driving Simulation is on interdisciplinary research on transportation and human factors to help improve safety, considering the interaction among the driver, vehicle and surrounding environment. This project is very helpful for Police Investigating purposes. II. CONCOMITANT WORK In general Vehicle Black Box system should store position information and in-vehicle data have Store position information and in-vehicle data have reliable position solution Use wireless communications for data exchange with the box allow third party services . In this paper, we propose this model to enhance smart phone security and user privacy. It is likely that Smartphone will have a strong presence in the future mobile phone market. Smartphone are often equipped with additional functionality of many things such as GPS systems, cameras, Wi-Fi, FM radios, Bluetooth, and various sensors. They can support many new applications such as Internet services, photography applications, and location based services. There are many demands for smart phone securities models in today's world. We implement a prototype of Different User on a real Smartphone system, Android, which is an open source platform. Although Android is based on the Linux kernel, it is a new OS specifically designed for mobile devices. This system have three different users such as(1) administrative users, who have complete control over Smartphone; (2) normal users, who have many Smartphone privileges but cannot install or uninstall critical system applications; (3) guest users, who have very limited privileges. Finally this paper we cannot fix exiting security flaws in smart phone system with reference queries. Wireless Black Box Using MEMS Accelerometer and GPS Tracking for Accidental Monitoring of Vehicles. In this work, wireless black box using MEMS accelerometer and GPS tracking system is developed for accidental monitoring. The system consists of cooperative components of an accelerometer, microcontroller unit, GPS device and GSM module. In the event of accident, this wireless device will send mobile phone short massage indicating the position of vehicle by GPS system to family member, emergency medical service (EMS) and nearest hospital. The system is compact and easy to install under rider seat. The system has been tested in real world applications using bicycles. The test results show that it can detect linear fall, non-linear fall and normal ride with
  3. 3. International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 6464(Print), ISSN 0976 – 6472(Online), Volume 5, Issue 4, April (2014), pp. high accuracy. Only Possible for two Wheeler sere discussed in reference paper. from car black box system those paper concern will transmit the information from Black Box to the server through Smartphone. Initially Smartphone will authenticate to the server by means of password. After Authentication black box will tr smart phone to transmit the information to the vehicle. Here this method is difficult to transmit the information because during accident driver also .In many cases without VANET Infrastructure, networks can be used for transmitting video clip data. Every car is equipped with car black box,, Global Positioning System(GPS) and GSM MODEM. The devices are always turning ON When car moves. Car Black Box and can communicate with each other in order communication. III. TOOLS USED Now for the monitoring purpose the working of the software used in this project was STISIM driving simulation software. The software, the car and the three projectors were all simulated toge to make a working model of the system. The following axis system was followed. Simulation Axis Systems: STISIM Drive uses three completely different axis systems to specify the driving simulation environment: the roadway axis system, the screen axi system. Roadway Axis System: The roadway axis system is 3D and in relation to the driver in the driving environment. This axis system is used in the SDL when positioning vehicles, buildings, pedestrians and other 3D models in the virtual environment. Longitudinal Position (or Distance): going down the road. Positive values indicate forward and negative values indicate backwards along this axis. Lateral Position (or Distance): Refers to the Y axis, the lateral left/right line with the roadway dividing line as zero. Positive values indicate a position to the right the roadway dividing line. Negative values a position to the left. Note that the the center of the roadway, but the dividing line between traffic. Using this method allows in defining an uneven number of lanes on either side of the road. Vertical Position: Referring to the Z axis is defined at zero. Positive values indicate a position above the ground, negative values below. International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 6472(Online), Volume 5, Issue 4, April (2014), pp. 36-42 © IAEME 38 high accuracy. Only Possible for two Wheeler sere discussed in reference paper. Ev from car black box system those paper concern will transmit the information from Black Box to the server through Smartphone. Initially Smartphone will authenticate to the server by means of password. After Authentication black box will transmit the information to the smart phone. Driver handles the smart phone to transmit the information to the vehicle. Here this method is difficult to transmit the information because during accident driver also .In many cases without VANET Infrastructure, networks can be used for transmitting video clip data. Every car is equipped with car black box,, Global Positioning System(GPS) and GSM MODEM. The devices are always turning ON When car moves. Car Black Box and can communicate with each other in order to transmit data by wireless Now for the monitoring purpose the working of the software used in this project was STISIM driving simulation software. The software, the car and the three projectors were all simulated toge to make a working model of the system. The following axis system was followed. STISIM Drive uses three completely different axis systems to specify the driving simulation environment: the roadway axis system, the screen axis system, and the model axis The roadway axis system is 3D and in relation to the driver in the driving environment. This axis system is used in the SDL when positioning vehicles, buildings, pedestrians n the virtual environment. Longitudinal Position (or Distance): Refers to the X axis, the longitudinal line out from the driver going down the road. Positive values indicate forward and negative values indicate backwards along Refers to the Y axis, the lateral left/right line with the roadway dividing line as zero. Positive values indicate a position to the right the roadway dividing line. Negative values a position to the left. Note that the roadway’s dividing line, is not necessarily always the center of the roadway, but the dividing line between traffic. Using this method allows in defining an uneven number of lanes on either side of the road. Referring to the Z axis, the vertical up/down line from the roadway ground, which is defined at zero. Positive values indicate a position above the ground, negative values below. Roadway Axis System International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 – © IAEME Evidence collection from car black box system those paper concern will transmit the information from Black Box to the server through Smartphone. Initially Smartphone will authenticate to the server by means of password. ansmit the information to the smart phone. Driver handles the smart phone to transmit the information to the vehicle. Here this method is difficult to transmit the information because during accident driver also .In many cases without VANET Infrastructure, 3G networks can be used for transmitting video clip data. Every car is equipped with car black box,, Global Positioning System(GPS) and GSM MODEM. The devices are always turning ON When car to transmit data by wireless Now for the monitoring purpose the working of the software used in this project was STISIM driving simulation software. The software, the car and the three projectors were all simulated together STISIM Drive uses three completely different axis systems to specify the s system, and the model axis The roadway axis system is 3D and in relation to the driver in the driving environment. This axis system is used in the SDL when positioning vehicles, buildings, pedestrians Refers to the X axis, the longitudinal line out from the driver going down the road. Positive values indicate forward and negative values indicate backwards along Refers to the Y axis, the lateral left/right line with the roadway dividing line as zero. Positive values indicate a position to the right the roadway dividing line. ding line, is not necessarily always the center of the roadway, but the dividing line between traffic. Using this method allows for flexibility , the vertical up/down line from the roadway ground, which is defined at zero. Positive values indicate a position above the ground, negative values below.
  4. 4. International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 – 6464(Print), ISSN 0976 – 6472(Online), Volume 5, Issue 4, April (2014), pp. 36-42 © IAEME 39 Screen Axis System: The screen axis system is a 2D (X, Y) coordinate system in relation to the physical display screen. This axis system is often used for positioning screen-based objects that are not affected by the immediate simulation environment such as the driver’s dashboard displays, mirrors and any images you wish to “overlay” the virtual environment with. Horizontal Position: Refers to the X axis, left/right positions across the screen. Position values can range from 0 to 1 and can be conceptualized as proportion of the horizontal screen space. A value of 0 is the far left and a value of 1 is the far right. Vertical Position: Refers to the Y axis, vertical positions across the screen. Position values can range from 0 to 1 and can be conceptualized as the proportion of the vertical screen space. Screen Axis System Model Axis System: The final axis system is the model axis system. This system defines how the 3D graphics models are oriented in 3D space. When adding models or manipulating models in the roadway environment you will need to know how the model orients itself in the world and what the various axes are. The image to the right depicts the position and orientation axis for all STISIM Drive models. It should be noted that the orientation of the model aligns with the roadway axis system; with the longitudinal X axis being positive going down the road, the lateral Y axis going positive to the right of the model, and the vertical Z axis going positive up. This illustration also shows the angle orientation axis. Therefore in the documentation if the word Yaw (or heading) is used it refers to angular rotation about the vertical Z axis. Pitching refers to angular rotation about the lateral Y axis. Finally, roll refers to angular motion about the longitudinal X axis. Model Axis System
  5. 5. International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 – 6464(Print), ISSN 0976 – 6472(Online), Volume 5, Issue 4, April (2014), pp. 36-42 © IAEME 40 IV. WORKING MODULE The following is the piece of code in scenario description language written to make the scenario: -1 AUTHOR: SARTHAK PAREEK -1 DATE: 06-21-2013 -1 -1 DESCRIPTION: -1 small town shops- left on Opal St. -1 traffic light monitoring -1 -1 VEHICLE SPEED: 45 MPH -1 APPROX TOTAL DIST: 6500 ft -1 APPROX START DIST: 000 ft. {Tags Defiles = C:UserStudentsMyProjectPDEs Speed Limit = C:UserStudentsMyProjectSpeed Limit Textures = C:UserStudentsMyProjectTextures} -1 END SIMULATION: 8600 End Simulation -1 ----------------- CRASH SETTINGS --------------------- -1 0, Previously Defined Events, %Defiles%CrashSettings_Shops.pde -1 SPEED LIMIT: 45 mph 0, Speed Limit, 48, 0 0, Police Begin, 2 150, Sign, 100, 0, %Speed Limit%Sp45Mph.mesh 1200, Sign, 100, 0, %Speed Limit%Sp45Mph.mesh 2200, Sign, 100, 0, %Speed Limit%Sp45Mph.mesh 4800, Sign, 100, 0, %Speed Limit%Sp45Mph.mesh -1 ----------------- DATA SAVE -------------------------- -1 DIST, TIME, SPEED, LATP, VHEAD, SW, THROT, BRK, PANLT, PANRT 0, Begin Block Save, 1, .099, DATA, 6, 1, 4, 7, 10, 26, 27, 28, 33, 340, Previously Defined Events, %Defiles%Shops_4_A01.pde -1 INT-01 (2000 FT) 1000, Previously Defined Events, %Defiles%Shops_4_A02.pde -1 INT-02 (3000 FT) 2000, Previously Defined Events, %Defiles%Shops_4_A03.pde -1 INT-03 (4000 FT) ------------------------------------------------------------- RIGHT TURN 4200, Previously Defined Events, %Defiles%Shops_4_A04.pde -1 INT-04 (6000 FT) 5200, Previously Defined Events, %Defiles%Shops_4_A05.pde -1 INT-05 (7000 FT) 6200, Previously Defined Events, %Defiles%Shops_4_A06.pde -1 INT-06 (8000 FT) ------------------------------------------------------------- LEFT TURN -1 INITIATE TREE MODEL TYPE -1 all types except palm trees 0, Tree, 0, 0, 15, 0{0}, 0{0}, 0 -1 ROAD CURVE 0, Curve, 0, 500, 500, 500, 0.001 4700, Curve, 0, 500, 500, 500, -0.001 -1 ROAD: 4 lanes, double yellow, no medium, grass 0, Roadway, 12, 4, 2, 2, 1, 10, 10, 0.4, 0.4, 0, -1, %Textures%Road15.Jpg, 255/255/255, 6, 0, -1, %Textures%Road15.Jpg, 255/255/255, 6, 0, -5, 8, %Textures%Road15.Jpg, %Textures%Grass05.Jpg, 255/255/255, 12, 0, 0, , , , 0 Following is the glimpse of how the output looks like while the scenario is being tested.
  6. 6. International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 – 6464(Print), ISSN 0976 – 6472(Online), Volume 5, Issue 4, April (2014), pp. 36-42 © IAEME 41 Output of stisim V. CONCLUSION The progress in science & technology is a non-stop process. New things and new technology are being adding up continusely. As the technology grows day by day, we can imagine about the future in which thing we may occupy every place. The proposed system based on ATMEGA microcontroller is found to be more compact, user friendly and less complex, which are ready to be used in order to perform. Though it is designed keeping in mind about the need for industry, it can extended for other purposes such as commercial & research applications. Due to the probability of high technology (ATMEGA microcontroller) used this protection system is fully software controlled with less hardware circuit. The feature makes this system is the base for future systems. Driving simulators are very popular and valuable in gaming and training. However, their benefits don't end there. They have already expanded them to clinical industries. And according to Stisim Drive, they provide the most cost-effective software that could ensure those simulators produce accurate and reliable results. REFERENCES 1) Cahalan, D., Cisin, I. & Crossley, H. (1969). American drinking practices: A national study of drinking behavior and attitudes. New Brunswick, NJ: Rutgers Center of Alcohol Studies. 2) Monograph No 6. Iudice, A., Bonanni, E., Maestri, M., Nucciarone,B., Brotini, S., Manca, L., Iudice, G., & Murri,L. (2002). Lormetazepam effects on daytime vigilance, psychomotor performance and simulated driving in young adult healthy volunteers. International Journal of Clinical Pharmacology and Therapeutics. 40(7): 304-309. 3) Kay, GG, Feldman N. (in press) Effects of armodafinil on simulated driving and self- report measures in obstructive sleep apnea patients prior to treatment with continuous positive airway pressure. Journal of Clinical Sleep Research.
  7. 7. International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 – 6464(Print), ISSN 0976 – 6472(Online), Volume 5, Issue 4, April (2014), pp. 36-42 © IAEME 42 4) Kay GG, Michaels MA, Pakull, B. (2009). Simulated driving changes in young adults with ADHD receiving mixed amphetamine salts extended release and atomoxetine. Journal of Attention Disorders. 12(4): 316-329. 5) Lee, J., Fiorentino, D., Reyes, M., Brown, T., Ahmad, O., Fell, J., Ward, N. & Dufour, R. (2010). Assessing the Feasibility of Vehicle-Based Sensors to Detect Alcohol Impairment. Washington, DC: National Highway Traffic Safety Administration. DOT HS 811 358. 6) Partinen, M., Hirvonen, K., Hublin,C., Halavaara, M., & Hiltunen, H. (2003). Effects of after midnight intake of zolpidem and temazepam on driving ability in women with nonorganic insomnia. Sleep Medicine, 4(6): 553-561. 7) Saunders, J., Aasland, I., Babor, T., De La Fuente, J. & Grand, M. (1993). Development of the Alchol Use Disorders Identification Test (AUDIT): WHO Collaborative Project on Early Detection of Persons with Harmful Alcohol Consuption – II. Addiction. 88: 791- 804. 8) Thompson, I., Williams, G., Caldwell, B., Aldington, S., Dickson, S., Lucas, N., McDowall, J., Weatherall, M., Robinson, G. & Beasley, R. (2010). Randomised double- blind, placebocontrolled trial of the effects of the party pills ‟BZP/TFMPP alone and in combination with alcohol. J Psychopharmacol, 1299-1308). 9) Ramesh Kamath, Siddhesh Nadkarni, Kundan Srivastav and Dr. Deepak Vishnu Bhoir, “Data Acquisition System and Telemetry System for Unmanned Aerial Vehicles for Sae Aero Design Series”, International Journal of Electronics and Communication Engineering & Technology (IJECET), Volume 4, Issue 5, 2013, pp. 90 - 100, ISSN Print: 0976- 6464, ISSN Online: 0976 –6472. 10) I.Rajani Kumari and G.Krishna Kishore, “A New Method To Prevent Accidents In Railways Using Microcontroller Based On Gsm And Gps Technology”, International Journal of Electronics and Communication Engineering & Technology (IJECET), Volume 4, Issue 5, 2013, pp. 90 - 100, ISSN Print: 0976- 6464, ISSN Online: 0976 –6472.

×