Truckslide Installation

17,004 views

Published on

It's no fun crawling into the back of your pickup or reaching over the side rails to pick up that 5-gallon bucket of paint, a tool box, groceries, or maybe even a compressor. Especially if you have a camper shell or tonneau cover. It's not that it's heavy, it's an awkward lifting position your body was not made for. (Those are the ones that get ya!)

With a Truckslide™ everything easily rolls out to where it can be reached. The Truckslide™ works great in pickup trucks, vans, service bodies, motor homes, and fifth wheel trailers. Your friends will be in awe when you pull out everything in the back of your truck with one hand. Your back will love it too!

Don’t hurt your back or your knees. Put a Truckslide™ to work.

Published in: Automotive
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
17,004
On SlideShare
0
From Embeds
0
Number of Embeds
14,484
Actions
Shares
0
Downloads
4
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Truckslide Installation

  1. 1. Installation Guide Roller Coaster™ www.highwayproducts.com
  2. 2. Roller Coaster™
  3. 3. Supplied Material List • 6 3/8" rubber washer • 6 3/8 - 16 rev lock nuts • 6 3/8 - 16 X 1-1/2" hex head bolts • 6 3/8" flat washer
  4. 4. Tools Needed • 9/16” socket • drill • 3/8" drill bit • 9/16” wrench • tape measure • rubber mallet • 1/4" pilot drill bit
  5. 5. 1. Un-crate Roller Coaster2. With the help of others, place Roller Coaster in bed of truck
  6. 6. 3. Place Roller Coaster all the way up against the cab side of bed
  7. 7. 4. Slide the tray out to the second click
  8. 8. 5. Move the unit so the it is flush with cab side of bed6. Make sure holes in the “Rear Flange” line up with the up slope of the corrugated bed 5 6
  9. 9. 7. Center the unit by measuring from side of bed to edge of unit
  10. 10. 8. Measure both sides multiple times to insure a centered install
  11. 11. 9. Some trucks have a cross member or fuel tank under the bed10.Inspect the undercarriage of your vehicle so you don’t drill through cross member or fuel tank
  12. 12. 11.Drill a pilot hole on the upside of the corrugated bed12.Inspect, then drill 3/8" hole13.Place rubber washer between the bottom of flange and bed of truck14.Insert 3/8" bolt through Roller Coaster and bed of truck
  13. 13. 15.Drill a pilot hole on the other side16.Inspect, then drill 3/8" hole17.Place rubber washer between the bottom of flange and bed of truck18.Insert 3/8" bolt through flange and bed of truck
  14. 14. 19.One person under the vehicle with 9/16 wrench, flat lock washers and lock nuts20.Place flat lock washer on the bolt showing underneath truck bed, place nut on bolt, and fasten.
  15. 15. 21.Tighten down both bolts
  16. 16. 22.Pull the tray out just far enough to see the middle mounting plates23.There are 4 mounting brackets (1 bolt for each bracket) drill on the up slope of bed24.Insert bolts, washers and nuts25.Tighten down all bolts
  17. 17. Questions?We Will Help You 800-866-5269 www.highwayproducts.com

×