Ic2200h Manual
Upcoming SlideShare
Loading in...5
×
 

Ic2200h Manual

on

  • 3,012 views

 

Statistics

Views

Total Views
3,012
Views on SlideShare
3,012
Embed Views
0

Actions

Likes
0
Downloads
10
Comments
1

0 Embeds 0

No embeds

Accessibility

Categories

Upload Details

Uploaded via as Adobe PDF

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
  • HELLO,

    It's my pleasure to write you at this moment.My name is miss CYNTHIA i saw your profile today on www.slideshare.net and i wish to request for your true friendship.I have an important reason of contacting you and i hope we can share great experiences together beyond here. Write to me direct to my e-mail box:(cynthiayaya1@hotmail.com) and i will send you my picture for you to know whom i am, thanks for your understanding. I wish to hear from you soon, God bless you.

    Yours friend,
    CYNTHIA.

    cynthiayaya1@h/otmail.c/om
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

Ic2200h Manual Ic2200h Manual Presentation Transcript

  • INSTRUCTION MANUAL VHF TRANSCEIVER i2200H This device complies with Part 15 of the FCC rules. Operation is sub- ject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • FOREWORD IMPORTANT READ ALL INSTRUCTIONS carefully and completely Thank you for purchasing this Icom product. The IC-2200H VHF TRANSCEIVER is designed and built with Icom’s superior before using the transceiver. technology and craftsmanship. With proper care, this product SAVE THIS INSTRUCTION MANUAL— This in- should provide you with years of trouble-free operation. struction manual contains important operating instructions for We want to take a couple of moments of your time to thank the IC-2200H. you for making your IC-2200H your radio of choice, and hope you agree with Icom’s philosophy of “technology first.” Many hours of research and development went into the design of EXPLICIT DEFINITIONS your IC-2200H. WORD DEFINITION D FEATURES Personal injury, fire hazard or electric shock R WARNING! may occur. ❍ 65 W* of high transmit output power Equipment damage may occur. CAUTION (except Korea/Taiwan versions) Recommended for optimum use. No risk of ❍ Tone squelch, DTCS squelch standard NOTE personal injury, fire or electric shock. ❍ Dual color (amber & green) LCD backlight ❍ Remote control microphone available (optional for some versions) ❍ Optional Digital modulator/demodulator ❍ Optional DTMF decoder Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Ger- many, France, Spain, Russia and/or other countries. i
  • PRECAUTION RWARNING RF EXPOSURE! This device emits NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. Radio Frequency (RF) energy. Extreme caution should be ob- served when operating this device. If you have any questions re- DO NOT push the PTT when not actually desiring to transmit. garding RF exposure and safety standards please refer to the DO NOT allow children to play with any radio equipment con- Federal Communications Commission Office of Engineering and taining a transmitter. Technology’s report on Evaluating Compliance with FCC Guide- lines for Human Radio frequency Electromagnetic Fields (OET During mobile operation, DO NOT operate the transceiver Bulletin 65) without running the vehicle’s engine. When the transceiver’s RWARNING! NEVER connect the transceiver to an AC power is ON and your vehicle’s engine is OFF, the vehicle’s bat- outlet. This may pose a fire hazard or result in an electric shock. tery will soon become exhausted. RWARNING! NEVER operate the transceiver while dri- BE CAREFUL! The transceiver will become hot when op- ving a vehicle. Safe driving requires your full attention—anything erating it continuously for long periods. less may result in an accident. AVOID placing the transceiver against walls or putting any- NEVER connect the transceiver to a power source of more thing on the top of the transceiver. This will obstruct heat dissi- than 16 V DC. This will ruin the transceiver. pation. NEVER connect the transceiver to a power source using re- AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below –10°C (+14˚F) or above +60°C verse polarity. This will ruin the transceiver. (+140˚F). NEVER cut the DC power cable between the DC plug and AVOID the use of chemical agents such as benzine or alcohol fuse holder. If an incorrect connection is made after cutting, the when cleaning, as they can damage the transceiver’s surfaces. transceiver may be damaged. USE Icom microphones only (supplied or optional). Other man- NEVER expose the transceiver to rain, snow or any liquids. The transceiver may be damaged. ufacturer’s microphones have different pin assignments and may damage the transceiver if attached. NEVER operate or touch the transceiver with wet hands. This may result in an electric shock or ruin the transceiver. ii
  • SUPPLIED ACCESSORIES AND OPTIONS I Supplied Accessories I Options q Microphone (HM-133V)* . . . . . . . . . . . . . . . . . . . . . . . . . 1 UT-108 DTMF DECODER UNIT w Fuse (20 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 UT-115 DIGITAL UNIT e DC power cable (3 m) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 HM-118TAN/TN DTMF MICROPHONES r Mobile mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . 1 HM-118N HAND MICROPHONE t Mounting screws, nuts and washers . . . . . . . . . . . . 1 set HM-133V REMOTE-CONTROL MICROPHONE y Microphone hanger† . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SP-10 EXTERNAL SPEAKER u Insulation sheet‡ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 OPC-440/OPC-647 MIC EXTENSION CABLES *HM-118TN DTMF MICROPHONE supplied versions are also available. OPC-441 SPEAKER EXTENSION CABLE Depending on version. † Used for optional unit installation, see p.91 for details. ‡ OPC-1132/OPC-347 DC POWER CABLES OPC-589 ADAPTER CABLE CS-2200H CLONING SOFTWARE q w e + OPC-478/OPC-478U CLONING CABLE OPC-474 CLONING CABLE r t y u iii
  • TABLE OF CONTENTS I Transmitting ................................................................................. 15 FOREWORD ........................................................................................... i I Selecting output power ................................................................ 16 IMPORTANT ............................................................................................ i I One-touch PTT function ............................................................... 16 EXPLICIT DEFINITIONS ......................................................................... i PRECAUTION ........................................................................................ ii 4 REPEATER OPERATION ......................................................... 17–23 I Accessing a repeater ................................................................... 17 SUPPLIED ACCESSORIES AND OPTIONS ......................................... iii I Subaudible tones ......................................................................... 19 TABLE OF CONTENTS ......................................................................... iv I Offset frequency .......................................................................... 21 QUICK REFERENCE GUIDE ............................................................ I–VI I Installation ....................................................................................... I I Repeater lockout .......................................................................... 21 I Your first contact ........................................................................... IV I Reversed duplex mode ................................................................ 22 I Repeater operation ........................................................................ V I Auto repeater ............................................................................... 23 I Programming memory .................................................................. VI 5 MEMORY OPERATION ............................................................ 24–34 I General description ...................................................................... 24 1 PANEL DESCRIPTION ................................................................. 1–8 I Front panel ..................................................................................... 1 I Memory channel selection ........................................................... 24 I Function display ............................................................................. 3 I Programming a memory channel ................................................. 25 I Rear panel ..................................................................................... 5 I Transferring memory contents ..................................................... 27 I Microphone (HM-133V) .................................................................. 6 I Programming channel names ....................................................... 29 I Microphone keypad ........................................................................ 7 I Memory clearing .......................................................................... 31 I Memory bank selection ................................................................ 32 2 SETTING A FREQUENCY .......................................................... 9–12 I Preparation .................................................................................... 9 I Memory bank setting .................................................................... 33 I Using the tuning dial ...................................................................... 9 I Transferring bank contents .......................................................... 34 I Using the keypad ......................................................................... 10 6 CALL CHANNEL OPERATION ................................................ 35–36 I Using the [Y]/[Z] keys ................................................................. 10 I Call channel selection .................................................................. 35 I Tuning step selection ................................................................... 11 I Call channel transferring .............................................................. 35 I Lock functions .............................................................................. 12 I Programming a call channel ........................................................ 36 3 BASIC OPERATION ................................................................. 13–16 7 SCAN OPERATION .................................................................. 37–42 I Receiving ..................................................................................... 13 I Scan types ................................................................................... 37 I Monitor function ........................................................................... 13 I Scan start/stop ............................................................................. 38 I Audio mute function ..................................................................... 14 I Scan edges programming ............................................................ 39 I Squelch attenuator ....................................................................... 14 I Skip channel setting ..................................................................... 41 I S-meter squelch ........................................................................... 15 I Scan resume condition ................................................................ 42 iv
  • 1 2 I Weather channel operation .......................................................... 83 3 8 PRIORITY WATCH .................................................................... 43–44 I Priority watch types ...................................................................... 43 I Microphone keys .......................................................................... 84 4 I Priority watch operation ............................................................... 44 I Partial reset .................................................................................. 85 I All reset ........................................................................................ 85 9 DTMF MEMORY ENCODER ..................................................... 45–47 5 I Programming a DTMF code ......................................................... 45 I Data cloning ................................................................................. 86 I Transmitting a DTMF code .......................................................... 46 14 SPECIFICATIONS ........................................................................... 88 6 I DTMF speed ................................................................................ 47 15 MAINTENANCE ........................................................................ 89–91 I Troubleshooting ........................................................................... 89 10 POCKET BEEP AND TONE SQUELCH ................................... 48–51 7 I Pocket beep operation ................................................................. 48 I Fuse replacement ........................................................................ 90 I Tone/DTCS squelch operation ..................................................... 50 I Optional unit installation ............................................................... 91 8 I Tone scan ..................................................................................... 51 16 CE .................................................................................................... 92 9 11 PAGER/CODE SQUELCH (Required Optional UT-108).......... 52–57 17 MODE ARRANGEMENT ........................................................... 93–94 I Pager function .............................................................................. 52 10 I Code programming ...................................................................... 52 I Pager operation ........................................................................... 55 11 I Code squelch ............................................................................... 57 12 DIGITAL MODE OPERATION (Required Optional UT-115) .... 58–73 12 I Digital mode operation ................................................................. 58 I Call sign programming ................................................................. 58 13 I Digital voice mode operation ........................................................ 61 I When receiving a Digital call ........................................................ 63 14 I Break-in communication .............................................................. 65 15 I Emergency communication .......................................................... 66 I Digital code/Call sign squelch operation ...................................... 67 16 I Slow data communication ............................................................ 68 I Other setting items ....................................................................... 69 17 I GPS operation ............................................................................. 72 13 OTHER FUNCTIONS ................................................................ 74–87 I Set mode ...................................................................................... 74 I Initial set mode ............................................................................. 79 v
  • QUICK REFERENCE GUIDE I Installation D Location D Using the mounting bracket ➀ Drill 4 holes where the mounting bracket is to be installed. Select a location which can support the weight of the trans- • Approx. 5.5–6 mm (1⁄4″) when using nuts; approx. 2–3 mm (1⁄8″) ceiver and does not interfere with driving in any way. We rec- when using self-tapping screws. ommend the locations shown in the diagram below. ➁ Insert the supplied screws, nuts and washers through the NEVER place the transceiver where normal operation of the mounting bracket and tighten. ➂ Adjust the angle for the clearest view of the function dis- vehicle may be hindered or where it could cause bodily injury. play. NEVER place the transceiver where air bag deployment may be obstructed. Nut Spring washer DO NOT place the transceiver where hot or cold air blows di- rectly onto it. Flat washer Mounting bracket AVOID placing the transceiver in direct sunlight. When using self-tapping screws Mounting nut Spring washer IMPORTANT! Detailed installation notes for Icom mobile transceivers to be fitted into vehicles are available. Contact your Icom dealer or distributor. I
  • QUICK REFERENCE GUIDE D Battery connection D DC power supply connection
  • NEVER connect the transceiver directly to a 24 V battery. Use a 13.8 V DC power supply with at least 15 A capacity.
  • DO NOT use the cigarette lighter socket for power con- Make sure the ground terminal of the DC power supply is nections. (See p. 5 for details) grounded. Attach a rubber grommet when passing the DC power cable through a metal plate to prevent short circuiting. • CONNECTING TO A DC POWER SUPPLY • See p. 90 for fuse replacement. • CONNECTING TO A DC POWER SOURCE • See p. 90 for fuse replacement. Grommet IC-2200H IC-2200H DC power − black ⊕ red + red supply 13.8 V _ black Fuses 20 A to an − AC ⊕ outlet 12 V battery Fuses 12 V Supplied − black 20 A DC power cable ⊕ red Crimp Solder NOTE: Use terminals for the cable connections. II
  • QUICK REFERENCE GUIDE D Antenna installation • Antenna connector The antenna uses a PL-259 connector. • Antenna location To obtain maximum performance from the transceiver, select • PL-259 CONNECTOR a high-quality antenna and mount it in a good location. A non- q Slide the coupling ring 30 mm radial antenna should be used when using a magnetic mount. down. Strip the cable jacket and soft solder. Trunk-mount Roof-mount antenna Coupling ring 10 mm (soft solder) antenna w Strip the cable as shown (Drill a hole or use a magnetic mount.) 10 mm Soft solder at left. Soft solder the cen- Gutter-mount antenna ter conductor. 1–2 mm e Slide the connector body solder solder on and solder it. r Screw the coupling ring onto the connector body. (10 mm ≈ 3⁄8 in) NOTE: There are many publications covering proper an- tennas and their installation. Check with your local dealer for more information and recommendations. D Connecting a microphone Connect a microphone to the eight-pin modular socket on the front panel of the transceiver. *HM-133V; A different microphone may be supplied with some versions of the IC-2200H. to antenna III
  • QUICK REFERENCE GUIDE I Your first contact 2. Tune the desired frequency [DIAL] will allow you to dial in the frequency you want to op- Now that you have your IC-2200H installed in your car or erate. Pages 9 and 11 will instruct you on how to set the tun- shack, you are probably excited to get on the air. We would ing speed. like to take you through a few basic operation steps to make your first “On The Air” an enjoyable experience. 1. Turning ON the transceiver Before powering up your IC-2200H, you may want to make [DIAL] sure the audio volume and squelch level controls are set in Using the HM-133V 9–10 o’clock positions. You can directly enter the frequency with the HM-133V keypad. [VOL] [EXAMPLE]: Setting frequency to 145.3625 MHz. [SQL] DIGITAL PRIO AO BUSY MUTE NAR Push MID Set both [VOL] and [SQL] controls to LOW LOCK PRIO ANM T-SCAN SCAN DUP 9–10 o’clock positions. SET TONE M/CALL V/ MHz MONI LOW DIGITAL PRIO AO BUSY MUTE Although you have purchased a brand new transceiver, some NAR Push MID LOW settings may be changed from the factory defaults because LOCK ANM T-SCAN PRIO SCAN DUP SET TONE M/CALL V/ MHz MONI LOW of the QC process. Resetting the CPU is necessary to start Push DIGITAL PRIO AO BUSY from factory default. MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW DIGITAL PRIO AO BUSY MUTE Push NAR MID LOW [PWR] [SET LOCK] [S.MW MW] LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW ➥ While pushing [SET LOCK ] and [S.MW MW ], push We hope these pointers have been helpful. Now you [PWR] for 1 sec. to reset the CPU. are ready to call CQ. IV
  • QUICK REFERENCE GUIDE I Repeater operation 1. Setting duplex Using the HM-133V Plus or minus duplex selection and the repeater tone setting Push [LOW DUP ] for 1 sec. once or twice to select minus can be made easily via HM-133V. duplex or plus duplex. S Push [DUP– 7(TONE)] for minus duplex; [DUP+ 8(TSQLS)] • The USA version has an auto repeater function, therefore, setting for plus duplex selection, push [FUNC] then [DUP– 7(TONE)] duplex is not required. to turn the repeater tone ON. DIGITAL PRIO AO BUSY MUTE DIGITAL PRIO AO BUSY NAR MUTE MID NAR Push LOW MID LOCK T-SCAN PRIO ANM SCAN DUP LOW SET TONE M/CALL V/ MHz MONI LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW DIGITAL PRIO AO BUSY MUTE NAR Push MID 2. Repeater tone LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW Push [TONE T-SCAN ] several times until “ ” appears, if the repeater requires a subaudible to be accessed. DIGITAL PRIO AO BUSY MUTE NAR Push , then MID LOW LOCK T-SCAN PRIO ANM SCAN DUP DIGITAL PRIO AO BUSY SET TONE M/CALL V/ MHz MONI LOW MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW V
  • QUICK REFERENCE GUIDE I Programming memory channels The IC-2200H has a total of 207 memory channels (including Using the HM-133V 6 scan edges and 1 call channel) for storing often used oper- q In VFO mode, set the desired operating frequency, includ- ating frequency, repeater settings, etc. ing offset direction, tone settings, etc. w Push [FUNC] then [CLR A(MW)]. 1. Setting a frequency • “M” indicator and memory channel number blink. In VFO mode, set the desired operating frequency with re- peater, tone and tuning steps, etc. DIGITAL PRIO AO BUSY Push , MUTE 2. Selecting a memory channel NAR MID LOW then Momentarily push [S.MW MW ], then rotate [DIAL] to select LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW the desired memory channel. • “M” indicator and memory channel number blink. e Push [Y]/[Z] to select the desired memory channel. YZ r Push [FUNC] then push [CLR A(MW)] for 1 sec. to pro- DIGITAL PRIO AO BUSY MUTE NAR gram. MID LOW • 3 beeps sound LOCK ANM T-SCAN PRIO SCAN DUP SET TONE M/CALL V/ MHz MONI LOW • Memory channel number automatically increases when continu- [S.MW MW] [DIAL] ing to push [CLR A(MW)] after programming. 3. Writing a memory channel Push and hold [S.MW MW ] for 1 sec. to program. • 3 beeps sound • Memory channel number automatically increases when continuing to push [S.MW MW ] after programming. VI
  • 1 PANEL DESCRIPTION I Front panel !3 Function display (p. 3) q PWR S.MW MW w e BANK OPT r t y u i o !0 !1 !2 q POWER KEY [PWR] e MICROPHONE CONNECTOR Turns power ON and OFF when pushed for 1 sec. Connects the supplied microphone. w MEMORY WRITE KEY [S.MW MW ] (p. 25) r VOLUME CONTROL [VOL] (p. 13) ➥ Selects a memory channel for programming. Adjusts the audio level. ➥ Programs the selected memory channel when pushed t SQUELCH CONTROL [SQL] (p. 13) for 1 sec. Varies the squelch level. • Continue to hold the key to increment the memory channel • The RF attenuator activates and increases the attenuation when automatically. rotated clockwise to the center position and further. 1
  • 1 PANEL DESCRIPTION y SET•LOCK KEY [SET LOCK ] !1 VFO/MHz TUNING•SCAN KEY [V/MHz SCAN ] 1 ➥ Enters set mode when pushed. (p. 74) ➥ Selects and toggles VFO mode and 1 MHz (or 10 MHz ➥ Keys the lock function ON and OFF when pushed for for some versions) tuning when pushed. (p. 9) ➥ Starts scan when pushed for 1 sec. (p. 38) 1 sec. (p. 12) • Cancels a scan when pushed during a scan. u MONITOR•CHANNEL NAME KEY [MONI ANM ] !2 BANK•OPTION KEY [BANK OPT ] ➥ Push to switch the monitor function ON and OFF. (p. 13) ➥ Push to select memory bank condition during memory ➥ In memory and call channel mode, switches the channel mode. (p. 32) names or number ON and OFF. (p. 29) ➥ Push for 1 sec. to enter the DTMF or option set mode. i OUTPUT POWER•DUPLEX KEY [LOW DUP ] !3 TUNING DIAL [DIAL] ➥ Each push changes the output power selection. (p. 16) ➥ Select DUP–, DUP+ and simplex operation when Selects the operating frequency (p. 9), memory channel (p. 24), the setting of the set mode item and the scanning pushed for 1 sec. (p. 17) direction (p. 38). o TONE•TONE SCAN KEY [TONE T-SCAN ] ➥ Each push selects a tone function. (pgs. 17, 48) D Microphone connector (front panel view) • Tone encoder, pocket beep, tone squelch or tone function q +8 V DC output (Max. 10 mA) OFF can be selected. w Channel up/down ➥ Push for 1 sec. to start/stop the tone scan function. e 8 V control IN (p. 51) r PTT ❍ While in the digital mode operation with the installing an q i t GND (microphone ground) optional Digital unit UT-115. y MIC (microphone input) ➥ Each push select the digital code (CSQL) squelch func- u GND tion, call sign (DSQL) squelch, pocket beep function i Data IN (CSQL or DSQL). (p. 67) !0 MEMORY/CALL•PRIORITY KEY [M/CALL PRIO ] ➥ Push to select and toggle memory, call and weather channel* modes. (pgs. 24, 35, 83) *Weather channels available for USA versions only. ➥ Starts priority watch when pushed for 1 sec. (p. 44) 2
  • 1 PANEL DESCRIPTION I Function display !7 !6 !5 !4 !3 !2 !1 q DIGITAL PRIO AO BUSY w !0 e MUTE NAR r o MID i t LOW u T- SCAN PRIO LOCK SCAN ANM DUP y SET M/CALL TONE V/MHz LOW MONI q FREQUENCY READOUT e AUDIO MUTE INDICATOR (p. 14) Shows the operating frequency, channel names, set mode Appears when the audio mute function is activated via mi- contents, etc. crophone control. • Frequency decimal point flashes while scanning. (p. 38) r NARROW MODE INDICATOR (p. 78) • “d” appears in place of the 1st digit while the DTMF memory Appears when the narrow mode is selected. function is in use. (p. 45) Narrow mode is not available with some versions. w TRANSMIT INDICATOR t OUTPUT POWER INDICATORS (p. 16) ➥ Appears while transmitting. (p. 15) “LOW” appears when low output power; “MID” and “LOW” ➥ Flashes while transmitting with the one-touch PTT func- appear when mid low output power; “MID” appears when tion. (p. 16) middle output power is selected. • Mid. low power is not available with some versions. 3
  • 1 PANEL DESCRIPTION y KEY INDICATORS !4 DIGITAL INDICATOR (p. 61) 1 Indicate the function(s) of the front panel keys directly Appears when digital mode is selected. below the function display. !5 LOCK INDICATOR (p. 12) u SKIP INDICATOR (p. 41) Appears when the lock function is activated. Appears when the selected memory channel is specified !6 TONE INDICATORS as a skip channel. ➥ “ ” appears while the subaudible tone encoder is in i MEMORY CHANNEL NUMBER INDICATORS use. (p. 17) ➥ Shows the selected memory channel number. (p. 24) ➥ “ ” appears while the tone (CTCSS) squelch function is ➥ “C” appears when the call channel is selected. (p. 35) in use. (p. 48) ➥ “ ” appears while the tone (DTCS) squelch function is o MEMORY INDICATOR (p. 24) in use. (p. 48) Appears when memory mode is selected. ➥ “ ” appears with the “ ” or “ ” indicator while the !0 S/RF INDICATORS pocket beep function (CTCSS or DTCS) is in use. (p. 48) ➥ Shows the relative signal strength while receiving sig- ❍ While in the digital mode operation with the installing an nals. (p. 13) optional Digital unit UT-115. ➥ Shows the output power level while transmitting. (p. 16) ➥ “ ” appears while the digital code (CSQL) squelch func- tion is in use. (p. 67) !1 BUSY INDICATOR (p. 13) ➥ “ ” appears while the call sign (DSQL) squelch function ➥ Appears when a signal is being received or the squelch is in use. (p. 67) is open. ➥ “ ” appears with the “ ” or “ ” indicator while the ➥ Flashes while the monitor function is activated. pocket beep function (CSQL or DSQL) is in use. (p. 67) !2 AUTO POWER-OFF INDICATOR (p. 81) !7 DUPLEX INDICATORS (p. 17) Appears while the auto power-off function is in use. “+” appears when plus duplex, “–” appears when minus !3 PRIORITY WATCH INDICATOR (p. 44) duplex operation is selected. Appears while the priority watch is activated; blinks while the watch is paused. 4
  • 1 PANEL DESCRIPTION I Rear panel q w r e q SPEAKER JACK [SP] e POWER RECEPTACLE [DC13.8V] Accepts an 8 Ω speaker. Accepts 13.8 V DC ±15% with the supplied DC power • Audio output power is more than 2.4 W. cable.51 w DATA JACK [DATA] NOTE: DO NOT use a cigarette lighter socket as a Connects to a PC or GPS receiver via an RS-232C cable power source when operating in a vehicle. The plug (D-sub 9-pin) for data communication in the RS-232C for- may cause voltage drops and ignition noise may be su- mat. perimposed onto transmit or receive audio. RS-232C (DB-9 female) r ANTENNA CONNECTOR [ANT] to [DATA] jack 5 Connects a 50 Ω antenna with a PL-259 connector and a 1 TxD GND 50 Ω coaxial cable. RxD 9 6 2.5(d) mm Pin 2 (RxD), Pin 3 (TxD), Pin 5 (GND) Make sure the connection between transceiver and PC, oth- erwise misreading may occur for data communication. 5
  • 1 PANEL DESCRIPTION I Microphone (HM-133V*) e UP/DOWN KEYS [Y]/[Z] 1 ➥ Push either key to change operating frequency, mem- ory channel, set mode setting, etc. (pgs. 10, 24) !1 ➥ Push either key for 1 sec. to start scanning. (p. 38) !0 q r ACTIVITY INDICATOR o w ➥ Lights red while any key, except [FUNC] and [DTMF-S], i e is pushed, or while transmitting. u ➥ Lights orange while the microphone keypad lock func- r y tion is activated. Mic element ➥ Lights green while the one-touch PTT function is in use. t t KEYPAD (pgs. 7, 8) y FUNCTION INDICATOR ➥ Lights orange while [FUNC] is activated—indicates the secondary function of keys can be accessed. ➥ Lights green when [DTMF-S] is activated—DTMF sig- nals can be transmitted with the keypad. *A different microphone u FUNCTION KEY [FUNC] (pgs. 7, 8) may be supplied de- pending on version. i DTMF MEMORY SELECT KEY [DTMF-S] (p. 46) o FUNCTION KEYS [F-1]/[F-2] (p. 84) Program and re-call your desired transceiver conditions. q VFO/LOCK KEY [VFO/LOCK] ➥ Push to select VFO mode. (p. 9) !0 BANK/OPTION KEY [BANK/OPTION] ➥ Push for 1 sec. to switch the lock function ON and OFF. ➥ Push to selects memory bank condition during memory (p. 12) mode. (p. 32) ➥ Push for 1 sec. to enter the DTMF or option set mode. w PTT SWITCH ➥ Push and hold to transmit; release to receive. !1 MEMORY/CALL KEY [MR/CALL] ➥ Switches between transmitting and receiving while the ➥ Push to select memory mode. (p. 24) ➥ Push for 1 sec. to select call channel. (p. 35) one-touch PTT function is in use. (p. 16) 6
  • 1 PANEL DESCRIPTION I Microphone keypad KEY FUNCTION SECONDARY FUNCTION ( +key) OTHER FUNCTIONS Switches between opening and closing the In memory mode switches the channel names squelch. (p. 13) or number indication ON and OFF. (p. 30) Starts and stops scanning. (p. 38) Starts and stops tone scanning. (p. 51) Starts and stops priority watch. (p. 44) Turns the one-touch PTT function ON and OFF. (p. 16) Selects high output power. (p. 16) Turns the DTCS squelch ON. (p. 50) After pushing : *Turns the DSQL function. (p. 67) Transmits the appropriate Selects mid. output power. (p. 16) Turns the DTCS pocket beep function ON. (p. 49) DTMF code. (pgs. 20, 46) *Turns the DSQL pocket beep function. When the DTMF memory en- (p. 16) Turns the DTMF memory encoder function coder is activated, push [0] to Selects low output power (p. 45) [9] to transmit the appropriate ON. DTMF memory contents. Selects minus duplex operation. (p. 18) Turns the subaudible tone encoder ON. (p. 46) (p. 18) Selects plus duplex operation. (p. 18) Turns the CTCSS pocket beep function ON.(p. 49) *Turns the CSQL pocket beep function. Selects simplex operation. (p. 18) Turns the tone squelch function ON. (p. 50) *Turns the CSQL function. (p. 67) No primary function. Sends a 1750 Hz tone signal while pushing and holding. (p. 20) *While in the digital mode operation with the installing an optional Digital unit UT-115. 7
  • 1 PANEL DESCRIPTION 1 KEY FUNCTION SECONDARY FUNCTION ( +key) OTHER FUNCTIONS ➥ Cancels frequency entry. (p. 10) ➥ Selects a memory channel for program- ➥ Cancels the scan or priority watch. ming. (p. 26) (pgs. 38, 44) ➥ Advances the memory channel number ➥ Exit set mode. (p. 74) when continuously pushed after pro- gramming is completed. (p. 26) ➥ Enters set mode (p. 74) DTMF memory OFF. (p. 46) ➥ Advances the set mode selection order after entering set mode. (p. 74) ➥ Sets the keypad for numeral input. Turns the subaudible tone encoder, pocket (p. 10) beep or CTCSS/DTCS tone squelch OFF. After pushing : ➥ Reverses the set mode selection order (pgs. 18, 49, 50) Transmits the appropriate after entering set mode. (p. 74) *Turns the pocket beep or CSQL/DSQL OFF. (p.63) DTMF code. (pgs. 20, 46) Adjusts the squelch level increments. Mutes the audio. (p. 14) (p. 13) • Mute function is released when any operation is performed. Sends a 1750 Hz tone signal for 0.5 sec. No primary function. (p. 20) Locks the digit keys on the keypad (includ- Adjusts the squelch level decrement. (p. 13) ing the A to D, # and M keys. (p. 12) • Lights orange while the microphone keypad lock function is activated. *While in the digital mode operation with the installing an optional Digital unit UT-115. 8
  • 2 SETTING A FREQUENCY I Preparation I Using the tuning dial D Turning power ON/OFF qRotate [DIAL] to set the frequency. ➥ Push [PWR] for 1 sec. to DIGITAL PRIO AO BUSY MUTE turn power ON and OFF. NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW [DIAL] Push [PWR] for 1 sec. • If VFO mode is not selected, push [V/MHz SCAN ] to select VFO D VFO mode selection mode. • The frequency changes according to the selected tuning steps. The transceiver has 2 basic operating modes: VFO mode and (p. 11) memory mode. wTo change the frequency in 1 MHz (10 MHz for some ver- ➥ Push [V/MHz SCAN ] to sions) steps, push [V/MHz SCAN ], then rotate [DIAL]. select VFO mode. • Pushing [V/MHz SCAN ] for DIGITAL PRIO AO BUSY 1 sec. starts scan function. MUTE NAR MID If scan starts, push [V/MHz LOW LOCK T-SCAN PRIO ANM SCAN DUP DIGITAL PRIO AO BUSY SCAN ] again to cancel it. SET TONE M/CALL V/ MHz MONI LOW MUTE NAR MID The display shows that the LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 1 MHz tuning step is selected. ➥ Push [VFO/LOCK] to select VFO mode. VFO/LOCK Note that in this manual, sections beginning with a micro- phone icon (as above), designate operation via the HM- 133V microphone. 9
  • 2 SETTING A FREQUENCY I Using the keypad I Using the [Y]/[Z] keys 2 ➥ Push [Y] or [Z] to select the desired frequency. The frequency can be directly set via numeral keys on the mi- Y Z crophone. YZ YZ • Pushing [Y]/[Z] for 1 sec. activates a scan. If scan YZ starts, push [Y]/[Z] again or push [CLR A(MW)] to z Push [VFO/LOCK] to VFO mode, if necessary. cancel it. ENT x Push [ENT C(T-OFF)] to activate the keypad for C digit input. c Push 6 keys to input a frequency. • When a digit is mistakenly input, push [ENT C(T-OFF)] to clear the input, then repeat input from the 1st digit. • Pushing [CLR A(MW)] clears input digits and retrieves the frequency. [EXAMPLE]: Setting frequency to 145.3625 MHz. DIGITAL PRIO AO BUSY MUTE NAR Push MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW DIGITAL PRIO AO BUSY MUTE NAR Push MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW Push DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW DIGITAL PRIO AO BUSY MUTE Push NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 10
  • 2 SETTING A FREQUENCY I Tuning step selection SET MODE USING Tuning steps are the minimum frequency change increments z Push [VFO/LOCK] to select VFO mode, if YZ when you rotate [DIAL] or push [Y]/[Z] on the microphone. VFO/LOCK necessary. The following tuning steps are available. x Push [SET B(D-OFF)] to enter set mode. c Push [SET B(D-OFF)] or [ENT C(T-OFF)] • 5 kHz • 10 kHz • 12.5 kHz • 15 kHz several times until “TS” appears. • 20 kHz • 25 kHz • 30 kHz • 50 kHz v Push [Y] or [Z] to select the desired tun- Y Z NOTE: For convenience, select a tuning step that matches ing step. the frequency intervals of repeaters in your area. b Push [CLR A(MW)] to exit set mode. q Push [V/MHz SCAN ] to se- lect VFO mode, if neces- sary. w Push [SET LOCK ] to enter [DIAL] set mode. e Push [SET] or [MONI] sev- 15 kHz tuning step eral times until “TS” appears DIGITAL PRIO AO BUSY MUTE as shown at left. NAR MID LOW r Rotate [DIAL] to select the LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW desired tuning step. t Push any key other than in- dicated function keys to exit set mode. 11
  • 2 SETTING A FREQUENCY I Lock functions 2 D Microphone keypad lock To prevent accidental channel changes and unnecessary function access, use the lock function. The transceiver has 2 This function locks the microphone keypad. different lock functions. ➥ Push [FUNC] then [SQLZ #(16KEY-L)] to Z D Frequency lock 16KEY-L switch the microphone keypad lock function This function locks [DIAL] and keys electronically and can be ON and OFF. • Lights orange while the microphone keypad lock used together with the microphone lock function. function is activated. ➥ Push [SET LOCK ] for • [PTT], [VFO/LOCK], [MR/CALL], [BANK/OP- 1 sec. to turn the lock func- Y Z TION], [Y], [Z], [F-1], [F-2], [DTMF-S] and tion ON and OFF. [FUNC] on the microphone can be used. • [PTT], [MONI ANM ], [VOL] • All keys on the transceiver can be used. Appears and [SQL] can be used while • The keypad lock function is released when the the channel lock function is in power is turned OFF then ON again. DIGITAL PRIO AO BUSY use. Also, TONE-1, TONE-2, MUTE NAR DTMF tones or DTMF mem- MID LOW LOCK T-SCAN PRIO ANM SCAN DUP ory contents can be transmit- SET TONE M/CALL V/ MHz MONI LOW ted from the microphone. ➥ Push [VFO/LOCK] for 1 sec. to switch the VFO/LOCK lock function ON and OFF. 12
  • 3 BASIC OPERATION I Receiving I Monitor function q Push [PWR] for 1 sec. to turn power ON. This function is used to listen to weak signals without disturb- w Set the audio level. ing the squelch setting or to open the squelch manually even ➥ Push [MONI ANM ] to open the squelch. when mute functions such as the tone squelch are in use. ➥ Rotate the [VOL] control to adjust the audio output ➥ Push [MONI ANM ] to open level. the squelch. ➥ Push [MONI ANM ] again to close the squelch. • “BUSY” blinks. e Set the squelch level. • Push [MONI ANM ] again to ➥ Rotate [SQL] fully counterclockwise in advance. cancel the function. ➥ Rotate [SQL] clockwise until the noise just disappears. ➥ When interference is received, rotate [SQL] clockwise DIGITAL PRIO AO BUSY MUTE again for attenuator operation. (p. 14) NAR MID LOW r Set the operating frequency. (pgs. 9, 10) LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW t When receiving a signal on the set frequency, squelch opens and the transceiver emits audio. • “BUSY” appears and the S/RF Appears when receiving a signal. indicator shows the relative ➥ Push [MONI 1(ANM)] to open the squelch. signal strength for the re- DIGITAL PRIO AO BUSY MONI • Push [MONI 1(ANM)] again to cancel the function. MUTE ceived signal. NAR 1 MID LOW LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW NOTE: When [SQL] adjustment is set too far clockwise, ✔CONVENIENT! (12–17 o’clock position) the squelch attenuator is acti- The squelch level can also be adjusted with vated. To monitor weak signals on the operating frequency, SQLY [SQLY D(MUTE)] and [SQLZ #(16KEY-L)]. Y Z deactivate the squelch attenuator function. See p. 82 for D details. DIGITAL PRIO AO BUSY MUTE NAR SQLZ MID LOW # LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 13
  • 3 BASIC OPERATION I Audio mute function I Squelch attenuator This function temporarily mutes the audio without disturbing The transceiver has an RF attenuator related to the squelch the volume setting. level setting. Approx. 10 dB attenuation is obtained at maxi- 3 mum setting. ➥ Push [FUNC] then [SQLY D(MUTE)] to mute Y ➥ Rotate [SQL] clockwise past the 12 o’clock position to ac- MUTE audio signals. tivate the squelch attenuator. • “MUTE” appears. • Attenuation level can be adjusted up to 10 dB (approx.) between • Push [CLR A(MW)] (or any other key) to cancel the 12 o’clock and fully clockwise position. function. • When setting the squelch from the microphone, a level greater Appears than ‘19’ activates the squelch attenuator. DIGITAL PRIO AO BUSY Noise squelch MUTE NAR Squelch MID LOW LOCK ANM T-SCAN PRIO SCAN DUP threshold SET TONE M/CALL V/ MHz MONI LOW Squelch Squelch is attenuator open. Shallow Deep NOTE: The squelch attenuator functions even when the monitor function is in use. Thus set the [SQL] within 10 to 12 o’clock position (12 to 19 level when setting with the HM-133V) is recommended when using the monitor func- tion. 14
  • 3 BASIC OPERATION I S-meter squelch I Transmitting INITIAL SET MODE USING CAUTION: Transmitting without an antenna will damage the transceiver. The transceiver has an S-meter squelch. The S-meter squelch allows you to set minimum signal level needed to NOTE: To prevent interference, listen on the channel be- open the squelch. fore transmitting by pushing [MONI ANM ], or q Turn the transceiver power OFF. [MONI 1(ANM)] on the microphone. wWhile pushing [SET LOCK ], push [PWR] for 1 sec. to q Set the operating frequency. (pgs. 9, 10) enter initial set mode. • Select output power if desired. See section at right for details. w Push and hold [PTT] to transmit. • “$” appears. • The S/RF indicator shows the output power selection. • A one-touch PTT function is available. See p. 16 for details. [SET LOCK ] [PWR] e Speak into the microphone using your normal voice level. • DO NOT hold the microphone too close to your mouth or speak ePush [SET] or [MONI] to select “SSQ” (S-meter squelch) too loudly. This may distort the signal. item. r Release [PTT] to return to receive. r Rotate [DIAL] to set the S-meter level or OFF. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE IMPORTANT! (for 65 W transmission): NAR NAR MID MID LOW LOW The IC-2200H is equipped with current detector circuit to LOCK ANM T-SCAN PRIO SCAN LOCK DUP ANM DUP T-SCAN PRIO SCAN SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW protect the power amplifier circuit from high current flowing. S-meter squelch OFF (default) S2 level (2 indicator level) When a high SWR (Standing Wave Ratio) antenna or no antenna is connected, or when the connected power sup- t Push [PWR] to exit initial set mode. ply’s voltage includes, the transceiver reduces transmit out- put power to 10–20 W (approx.) automatically. 15
  • 3 BASIC OPERATION I Selecting output power I One-touch PTT function The transceiver has 4* output power levels to suit your oper- The PTT switch can be operated as a one-touch PTT switch ating requirements. Low output powers during short-distance (each push switches between transmit/receive). Using this 3 communications may reduce the possibility of interference to function you can transmit without pushing and holding the other stations and will reduce current consumption. PTT switch. *The Taiwan version has only 3 levels. To prevent accidental, continuous transmissions with this Push [LOW DUP ] several times to select the output power. function, the transceiver has a time-out timer. See p. 80 for details. POWER OUTPUT S/RF INDICATOR Taiwan z Push [FUNC] then [PRIO 3(PTT-M)] to turn the PTT-M 65 W (50 W†) 24 W High: one-touch PTT function ON. • The activity indicator lights green. 25 W* 10 W* Mid.: x Push [PTT] to transmit and push again to re- 10 W* N/A ceive. Mid. Low: • Two beeps sound when transmission is started and a 5 W* 5 W* Low: long beep sounds when returning to receive. • “$” flashes when transmitting with the one-touch *approx., †Korea version PTT function. • The output power can be changed while transmitting. The microphone can also be used to select output power. DIGITAL PRIO AO BUSY MUTE ➥ Push [HIGH 4(DTCS)] for high output power; NAR MID LOW S HIGH [MID 5(DTCSS)] for middle output power LOCK ANM T-SCAN PRIO SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 4 (push again for mid. low output power); and [LOW 6(DTMF)] for low output power. c Push [FUNC] then [PRIO 3(PTT-M)] to turn the MID • The output power can be changed via the microphone 5 one-touch PTT function OFF. during receive only. • The activity indicator goes out. LOW 6 16
  • 4 REPEATER OPERATION I Accessing a repeater q Set the receive frequency (repeater output frequency). r Push and hold [PTT] to transmit. • The displayed frequency automatically changes to the transmit (pgs. 9, 10) w Push [LOW DUP ] for 1 sec., once or twice, to select frequency (repeater input frequency). • If “OFF” appears, confirm that the offset frequency (p. 21) is set minus duplex or plus duplex. correctly. • “–” or “+” appears to indicate the transmit frequency for minus t Release [PTT] to receive. shift or plus shift, respectively. • When the auto repeater function is turned ON (available for the DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY USA version only), steps w and e are not necessary. (p. 23) MUTE MUTE NAR NAR MID MID LOW LOW Either “–” or “+” appears. LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW DIGITAL PRIO AO BUSY While receiving While transmitting MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP yPush [MONI ANM ] to check whether the other station’s SET TONE M/CALL V/ MHz MONI LOW transmit signal can be received directly. uTo return to simplex operation, push [LOW DUP ] for e Push [TONE T-SCAN ] several times to turn ON the sub- 1 sec., once or twice, to clear the “–” or “+” indicator. audible tone encoder, according to repeater requirements. iTo turn OFF the subaudible tone encoder, push • “ ” appears [TONE T-SCAN ] several times until no tone indicators ap- • 88.5 Hz is set as the default; refer to p. 19 for tone frequency set- pear. tings. • When the repeater requires a different tone system, see p. 20. Appears DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 17
  • 4 REPEATER OPERATION z Set the receive frequency (repeater output fre- m Push [SIMP 9(TSQL)] to return to simplex oper- DUP– SIMP quency). (pgs. 9, 10) ation. 7 9 x Push [DUP– 7(TONE)] to select minus duplex; • “+” or “–” indicator disappears. , To turn OFF the subaudible tone encoder, push S push [DUP+ 8(TSQLS)] to select plus duplex. DUP+ [FUNC] then [ENT C(T-OFF)]. 8 Push DIGITAL PRIO AO BUSY 4 MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW Push DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW c Push [FUNC] then [DUP– 7(TONE)] to turn ON the subaudible tone encoder according to re- peater requirements. • Refer to p. 19 for the tone frequency setting. • When the repeater requires a different tone system, see p. 20. Push , MUTE DIGITAL PRIO AO BUSY NAR MID then . LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW v Push and hold [PTT] to transmit. b Release [PTT] to receive. n Push [MONI 1(ANM)] to check whether the other station’s transmit signal can be received directly. 18
  • 4 REPEATER OPERATION I Subaudible tones z Set the mode/channel you wish to set the sub- SET MODE USING SET audible tones to, such as VFO mode or mem- (Encoder function) B ory/call channel. • The subaudible tone frequency is independently pro- D Subaudible tones grammed into each mode or channel. q Select the mode/channel you wish to set the subaudible x Push [SET B(D-OFF)] to enter set mode. tones to, such as VFO mode or memory/call channel. c Push [SET B(D-OFF)] or [ENT C(T-OFF)] several w Push [SET LOCK ] to enter set mode. times until “ ” and “rt” appears; or until “ ” and e Push [SET] or [MONI] several times until “ ” and “rt” ap- “Ct” appears for tone squelch or pocket beep pears; or until “ ” and “Ct” appears for tone squelch or use. pocket beep use. • When “d” is displayed in place of the 100 MHz digit, • When “d” is displayed in place of the 100 MHz digit, cancel the cancel the DTMF memory encoder in advance. (p. 46) DTMF memory encoder in advance. (p. 46) DIGITAL PRIO AO BUSY MUTE DIGITAL PRIO AO BUSY NAR MUTE MID NAR LOW MID Push LOCK T-SCAN PRIO ANM SCAN DUP LOW SET TONE M/CALL V/ MHz MONI LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW r Rotate [DIAL] to select and set the desired subaudible fre- v Push [Y] or [Z] to select and set the desired Y Z quency. subaudible tone frequency. t Push any key other than [SET] or [MONI] to exit set mode. YZ • Push and hold [Y]/[Z] to change the above tones continuously. NOTE: The subaudible tone encoder frequency can be set b Push [CLR A(MW)] to exit set mode. in a memory/call channel temporarily. However, the set fre- quency is cleared once another memory channel or VFO • Subaudible tone frequency list (unit: Hz) mode is selected. To store the tone frequency permanently, 67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1 overwrite the channel information. 69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6 71.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.8 74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3 77.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1 19
  • 4 REPEATER OPERATION D DTMF tones D 1750 Hz tone ➥ Push [DTMF-S], then push the keys of the de- The microphone has 1750 Hz tone capability, used for ring DTMF-S sired DTMF digits. tone when calling, etc. • The function indicator lights green. z Push [FUNC]. • 0–9, A–D, M(E) and #(F) are available. 4 TONE-1 • The function indicator lights orange. • When “d” is displayed in place of the 100 MHz digit, x Push [M(TONE-1)] to transmit a 1750 Hz tone M cancel the DTMF memory encoder in advance. (p. 46) call signal for 0.5 sec.; push and hold TONE-2 • Push [DTMF-S] again to return the keypad to nor- [0(TONE-2)] to transmit a 1750 Hz tone call mal function control. signal for an arbitrary period. • The transceiver has 10 DTMF memory channels • The function indicator goes out automatically. for autopatch operation. See p. 45 for details. Push , Push , then push desired keys. then or . 20
  • 4 REPEATER OPERATION I Offset frequency I Repeater lockout SET MODE USING INITIAL SET MODE USING When communicating thorough a repeater, the transmit fre- quency is shifted from the receive frequency by an amount This function helps prevent interference to other stations by determined by the offset frequency. inhibiting your transmission when a signal is received. The transceiver has two inhibiting conditions, repeater and busy. q Push [SET LOCK ] to enter set mode. w Push [SET] or [MONI] until “±” and offset frequency appear. q Push [PWR] to turn power OFF. w While pushing [SET LOCK ], turn power ON to enter ini- DIGITAL PRIO AO BUSY MUTE NAR tial set mode. MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW [DIAL] e Rotate [DIAL] to set the desired offset frequency. • Push [V/MHz] to select the 1 MHz tuning steps. [SET LOCK ] [PWR] r Push any key other than indicated function keys to exit e Push [SET] or [MONI] several times until the “RLO” dis- set mode. play appears as shown below. z Push [SET B(D-OFF)] to enter set mode. r Rotate [DIAL] to turn the repeater lockout function to “RP,” SET x Push [SET B(D-OFF)] or [ENT C(T-OFF)] until “±” “BU” or OFF. B and offset frequency appear. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR MID MID LOW LOW DIGITAL PRIO AO BUSY LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP MUTE SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW NAR MID Push LOW LOCK T-SCAN PRIO ANM SCAN DUP • “RP”: Transmit is inhibited when a signal with un-matched sub- SET TONE M/CALL V/ MHz MONI LOW audible tone is received. • “BU”: Transmit is inhibited when a signal is received. t Push [PWR] to exit initial set mode. c Push [Y] or [Z] to set the desired offset. Y Z • Direct frequency entry from the keypad is not possi- ble. v Push [CLR A(MW)] to exit set mode. 21
  • 4 REPEATER OPERATION I Reversed duplex mode SET MODE USING z Push [SET B(D-OFF)] to enter set mode. When the reversed duplex mode is selected, the receive fre- SET x Push [SET B(D-OFF)] or [ENT C(T-OFF)] until quency shifts. (Transmit frequency shifts in normal duplex mode.) 4 B Each receive and transmit frequency is shown in the table “REV” appears. below with the following conditions; DIGITAL PRIO AO BUSY Input frequency : 145.30 MHz MUTE NAR MID Direction : – (negative) Push LOW LOCK T-SCAN PRIO ANM SCAN DUP SET Offset frequency : 0.6 MHz TONE M/CALL V/ MHz MONI LOW Reversed OFF ON Rx frequency 145.30 MHz 144.70 MHz c Push [Y] or [Z] to set the reversed duplex Y Z Tx frequency 144.70 MHz 145.30 MHz mode ON and OFF. v Push [CLR A(MW)] to exit set mode. q Push [SET LOCK ] to enter set mode. w Push [SET] or [MONI] several times until the “REV” dis- play appears as shown below. e Rotate [DIAL] to turn the reversed duplex mode ON or OFF. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW r Push any key other than [SET] or [MONI] to exit set mode. 22
  • 4 REPEATER OPERATION I Auto repeater (U.S.A. version only) INITIAL SET MODE USING r Rotate [DIAL] to turn the auto repeater function to “R1,” The USA version automatically activate the repeater settings (DUP– or DUP+ and tone encoder ON/OFF) when the operating “R2” or OFF. frequency falls within the general repeater output frequency DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE range and deactivate them when outside of the range. NAR NAR MID MID LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW D Setting the auto repeater function ON/OFF Auto repeater function is Auto repeater function is ON, q Push [PWR] to turn power OFF. turned OFF. tone encoder is ON. w While pushing [SET LOCK ], turn power ON to enter initial • “R1”: auto repeater is ON, tone encoder is OFF. • “R2”: auto repeater is ON, tone encoder is ON. set mode. t Push [PWR] to exit initial set mode. D Frequency range and offset direction [SET LOCK ] [PWR] Frequency range Duplex direction 145.200–145.495 MHz e Push [SET LOCK ] several times until the “RPT” display “–” appears 146.610–146.995 MHz appears as shown above right. 147.000–147.395 MHz “+” appears 23
  • 5 MEMORY OPERATION I General description D Using the [Y]/[Z] keys The transceiver has 207 memory channels including 6 scan edge memory channels (3 pairs), and 1 call channel. Each of z Push [MR/CALL] to select memory mode. these channels can be individually programmed with operat- MR/CALL x Push [Y] or [Z] to select and set the desired Y Z 4 ing frequency (pgs. 9, 10), duplex direction (p. 17) and offset memory channel. (p. 21), subaudible tone encoder or tone squelch and its tone YZ • Pushing [Y]/[Z] for 1 sec. activates a scan. 5 Y/Z frequency (pgs. 19, 48–50) and skip information* (p. 41). YZ • If scan is activated, push [Y]/[Z] again or push In addition, a total of 10 memory banks, A to J, are available [CLR A(MW)] to stop it. for usage by group, etc. *except for scan edge memory channels. D Using the keypad z Push [MR/CALL] to select memory mode. MR/CALL x Push [ENT C(T-OFF)] to activate the keypad I Memory channel selection for numeral input. c Push 3 appropriate digit keys to input a chan- D Using the tuning dial Y/Z nel number. q Push [M/CALL PRIO ] • When inputting non-programmed channel num- once or twice to select bers, the previous memory channel appears. • Push only 1 appropriate digit key, [MONI 1(ANM)], memory mode. [SCAN 2(T-SCAN)] or [PRIO 3(PTT-M)], then push • “M” indicator appears. [DIAL] M [M(TONE-1)] or [SQLZ #(16KEY-L)] to select scan Z w Rotate [DIAL] to select M edge channels. “M” and “#” can be used for “A” Appears the desired memory and “b” respectively. channel. DIGITAL PRIO AO BUSY MUTE NAR • Programmed memory MID LOW channels only can be se- LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW lected. 24
  • 5 MEMORY OPERATION I Programming a memory channel e Rotate [DIAL] to select the memory channel to be pro- VFO settings, including the set mode contents such as sub- audible tone frequency, etc., can be programmed into a mem- grammed. ory channel. • Memory channels not yet programmed are blank. r Push [S.MW MW ] for 1 sec. to program. q Set the desired frequency in VFO mode. • 3 beeps sound. ➥ Push [V/MHz SCAN ] to select VFO mode. • Memory channel number automatically increases when contin- ➥ Set the frequency using [DIAL]. uing to push [S.MW MW ] after programming. ➥ Set other data (e.g. tone frequency, duplex information, etc.) if required. ✔CONVENIENT w Push [S.MW MW ] momentarily. Memory programming can be performed in versatile ways • “M” indicator and the memory channel number blink. e.g. memory channel to the same (or different) memory chan- nel, memory channel to the call channel, etc. [EXAMPLE]: Programming 145.870 MHz into memory channel 20 (blank channel) via the front panel. S.MW MW () SCAN Push Rotate for setting frequency, etc. Push momentarily. V/ MHz DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM ANM SCAN DUP DUP DUP SET SET SET TONE M/CALL TONE M/CALL TONE M/CALL V/ MHz V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW S.MW MW Push for 1 sec. ➠ Rotate and continue to push “ “Beep DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE “ Beep NAR NAR NAR MID MID MID “ Beep LOW LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM SCAN DUP ANM DUP “ SET TONE M/CALL V/ MHz LOW SET SET MONI TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW 25
  • 5 MEMORY OPERATION D Programming a memory channel via the microphone The microphone can also be used to program mem- MW ory channels. z Set the desired frequency in VFO mode. v Push [FUNC] then [CLR A(MW)] for 1 sec. to program. ➥ Push [VFO/LOCK] to select VFO mode. ➥ 3 beeps may sound and the VFO contents (including ➥ Set the frequency using the keypad. 5 the subaudible tone frequency, etc.) are programmed. ➥ Set other data (e.g. offset frequency, duplex direction, sub- ➥ Memory channel number increases when continuing to audible tone encoder ON/OFF and its frequency), if neces- push [CLR A(MW)] after programming. sary. x Push [FUNC] then [CLR A(MW)] momentarily. c Select the memory channel to be programmed. ➥ Push [Y] or [Z] to select the memory channel (direct nu- Y Z meral input cannot be used). [EXAMPLE]: Programming 145.870 MHz into memory channel 20 (blank channel) via the microphone. Push then momentarily. Push Push DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM ANM SCAN DUP DUP DUP SET SET SET TONE M/CALL TONE M/CALL TONE M/CALL V/ MHz V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW Push then 1 sec. ➠ Push and continue to push “ “Beep DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE “ Beep NAR NAR NAR MID MID MID “ Beep LOW LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP “ SET TONE M/CALL V/ MHz LOW SET SET MONI TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW 26
  • 5 MEMORY OPERATION I Transferring memory contents This function transfers a memory channel’s contents to VFO (or another memory/call channel). This is useful when search- ing for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency etc. D Memory/call➪VFO z Select the memory/call channel to be MR/CALL transferred. q Select the memory/call channel to be transferred. ➥ Push [MR/CALL] to select memory mode, ➥ Push [M/CALL PRIO ] to select memory mode, then ro- then select the desired memory channel tate [DIAL] to select the desired memory channel. MW YZ via [Y]/[Z] or keypad. ➥ Push [M/CALL PRIO ] for 1 sec. to select the call chan- ➥ Push [MR/CALL] for 1 sec. to select the nel. call channel. w Push [S.MW MW ] for 1 sec. to transfer the selected mem- [Y]/[Z] x Push [FUNC], then [CLR A(MW)] for 1 sec. to ory/call channel contents to the VFO. transfer the selected memory/call channel • VFO mode is selected automatically. contents to the VFO. • VFO mode is selected automatically. [EXAMPLE]: Transferring memory channel 30 contents to VFO. Front panel operation: S.MW MW (M/CALL) to select memory mode. Rotate for setting memory channel. PRIO Push Push for 1 sec. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM ANM SCAN DUP DUP DUP SET SET SET TONE M/CALL TONE M/CALL TONE M/CALL V/ MHz V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW HM-133V operation: Push to select memory mode. Select memory channel. Push then push for 1 sec. 27
  • 5 MEMORY OPERATION z Select the memory/call channel to be trans- D Memory/call➪call/memory MR/CALL ferred. q Select the memory/call channel to be transferred. ➥ Push [MR/CALL] to select memory mode, ➥ Push [M/CALL PRIO ] to select memory mode, then ro- then select the desired memory channel tate [DIAL] to select the desired memory channel. MW YZ via [Y]/[Z] or keypad. ➥ Push [M/CALL PRIO ] for 1 sec. to select the call channel. ➥ Push [MR/CALL] for 1 sec. to select the w Push [S.MW MW ] momentarily. call channel. 5 • “M” indicator and “– –” indication blink, and shows VFO condi- [Y]/[Z] x Push [FUNC], then [CLR A(MW)] momentarily. tions. • “M” indicator and “– –” indication blink, and shows e Rotate [DIAL] to select the target memory channel. VFO conditions. • “C” blinks when the call channel is selected. c Push [Y]/[Z] to select the target memory YZ • Scan edge channels, 1A/1b, 2A/2b, 3A/3b, can also be selected. channel. r Push [S.MW MW ] for 1 sec. to transfer the selected mem- • “C” blinks when the call channel is selected. ory/call channel contents to the target memory. • Scan edge channels can also be selected. • The targeted memory and transferred contents are indicated. • The keypad cannot be used for the selection. v Push [FUNC] then push [CLR A(MW)] for 1 sec. to transfer the selected memory/call channel contents to the target memory. • The targeted memory and transferred contents are indicated. [EXAMPLE]: Transferring memory channel 30 contents to channel 31. Front panel operation: S.MW S.MW MW MW Select the target channel. Select the memory channel, then push . Push for 1 sec. DIGITAL PRIO AO BUSY AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK T-SCAN PRIO SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM ANM SCAN DUP DUP DUP SET SET SET TONE M/CALL M/CALL TONE M/CALL TONE M/CALL V/ MHz V/ MHz V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW HM-133V operation: Select the memory channel, push then push . Push then push for 1 sec. 28
  • 5 MEMORY OPERATION I Programming channel names r Push [SET LOCK ] to select the channel name program- Each memory channel and the call channel can be pro- grammed with an alphanumeric channel name for easy ming condition. • Frequency readouts disappear. recognition and can be indicated independently by channel. t Rotate [DIAL] to select the desired character. Names can be a maximum of 6 characters— see the table • The selected character blinks. below for available characters. y Push [SET] or [MONI] to move the cursor to left or right, (space) (+) (–) (=) (✱) (/) (() ()) (|) (0) respectively. u Repeat steps t and y until the desired channel names (1) (2) (3) (4) (5) (6) (7) (8) (9) (A) are displayed. i Push any key other than [SET] or [MONI] to program the (B) (C) (D) (E) (F) (G) (H) (I) (J) (K) name and exit the channel name programming condition. o Push [MONI ANM ] for 1 sec. to return to frequency indi- (L) (M) (N) (O) (P) (Q) (R) (S) (T) (U) cation if desired. (V) (W) (X) (Y) (Z) IMPORTANT!: Once channel name indication mode is selected, always access the channel name programming q Push [M/CALL PRIO ] to select memory mode. condition when [SET LOCK ] is pushed. w Rotate [DIAL] to select the desired memory channel. When set mode accessing is necessary, cancel the chan- e Push [MONI ANM ] for 1 sec. to select channel name indi- nel name indication by pushing [MONI ANM ] for 1 sec., cation mode. then access to set mode. • 1 short and 1 long beep sound. [EXAMPLE]: Programming “CLUB” into memory channel 1. ( SET ) or () Select memory channel 15, Push any other keys than Push LOCK ANM Rotate to select the MONI (MONI) for 1 sec. ( SET ) or (MONI) . then push to move the cursor. ANM LOCK ANM character. Repeat DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY previous MUTE MUTE MUTE MUTE NAR NAR NAR NAR steps. MID MID MID MID LOW LOW LOW LOW LOCK T-SCAN PRIO SCAN LOCK LOCK LOCK T-SCAN PRIO ANM ANM ANM ANM SCAN DUP DUP DUP DUP SET SET SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW MONI LOW 29
  • 5 MEMORY OPERATION Channel names can also be programmed via the mi- crophone. z Select the memory/call channel to be assigned memory b Push [SET B(D-OFF)] or [ENT C(T-OFF)] to move the cur- names. sor to left or right, respectively. ➥ Push [MR/CALL] to select memory mode, then select n Repeat steps v and b until the desired channel names YZ the desired memory channel via [Y]/[Z] or keypad. are displayed. 5 m Push [CLR A(MW)] to program the name and exit the • Scan edge channels can also be selected. ➥ Push [MR/CALL] for 1 sec. to select the call channel. channel name programming condition. x Push [FUNC], then [MONI 1(ANM)] momentarily. , Push [FUNC], then push [MONI 1(ANM)] to return to fre- c Push [SET B(D-OFF)]. quency indication if desired. • Frequency readouts disappear. v Push [Y]/[Z] to select the desired character. YZ • The selected character blinks. [EXAMPLE]: Programming “CLUB” into memory channel 15. Select memory channel 15, Push or to move Push to select the character. Push . push , then push . the cursor. Repeat DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY previous MUTE MUTE MUTE MUTE NAR NAR NAR NAR steps. MID MID MID MID LOW LOW LOW LOW LOCK PRIO PRIO ANM T-SCAN SCAN LOCK DUP ANM LOCK ANM LOCK ANM T-SCAN SCAN DUP DUP DUP SET SET SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW MONI LOW 30
  • 5 MEMORY OPERATION I Memory clearing r Push [S.MW MW ] momentarily, then push [S.MW MW ] Contents of programmed memories can be cleared (blanked), if desired. again for 1 sec.
  • This operation must be performed within 1.5 sec. q Push [V/MHz SCAN ] to select VFO mode. • 3 beeps sound, then the frequency is cleared. w Push [S.MW MW ] momentarily. • “M” indicator blinks continuously. • When clearing the call channel, the current VFO conditions are • “M” indicator and the memory channel number blink. re-programmed into the call channel automatically. e Rotate [DIAL] to select the memory channel to be cleared. t Push any key, except [S.MW MW ], to return to VFO • Memory channels not yet programmed are blank. mode. NOTE: Be careful!— the contents of cleared memories CANNOT be recalled. [EXAMPLE]: Clearing memory channel 20. S.MW MW ( ) to select VFO. SCAN Push Push momentarily. Rotate for selecting memory channel.. V/ MHz DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM ANM SCAN DUP DUP DUP SET SET SET TONE M/CALL TONE M/CALL TONE M/CALL V/ MHz V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW S.MW MW S.MW MW S.MW MW Push momentarily, then push again for 1 sec. Push any other keys than . “ “Beep DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE “ Beep NAR NAR MID MID “ Beep LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO ANM SCAN DUP “ SET TONE M/CALL V/ MHz LOW SET MONI TONE M/CALL V/ MHz MONI LOW 31
  • 5 MEMORY OPERATION I Memory bank selection The IC-2200H has a total of 10 banks (A to J). Regular mem- z Push [MR/CALL] to select memory mode. ory channels, 0 to 199, are assigned into the desired bank for BANK/OPTION x Push [BANK/OPTION] to select memory easy memory management. bank condition. • Bank initial blinks q Push [M/CALL PRIO ] to select memory mode. c Push [Y]/[Z] to select the desired bank, A YZ 5 w Push [BANK OPT ] to select memory bank condition. to J. • Bank initial blinks • Only programmed memory bank can be se- lected. [DIAL] v Push [CLR A(MW)] to set the bank. [Y]/[Z] DIGITAL PRIO AO BUSY MUTE • Initial stops blinking. NAR MID b Push [Y]/[Z] to select the desired con- YZ LOW LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW tents in the bank. [BANK OPT ] • No channel numbers are displayed for memory bank operation. e Rotate [DIAL] to select the desired bank, A to J. n To return to regular memory condition, • Banks that have no programmed contents are skipped. push [BANK/OPTION] then [CLR A(MW)]. r Push [BANK OPT ] to set the bank. • Initial stops blinking. t Rotate [DIAL] to select the contents in the bank. • No channel numbers are displayed for memory bank operation. y To return to regular memory condition, push [BANK OPT ] twice. 32
  • 5 MEMORY OPERATION I Memory bank setting z Push [MR/CALL] then select the desired BANK/OPTION YZ memory channel via [Y]/[Z] or keypad. q Push [M/CALL PRIO ] to select memory mode, then se- x Push [SET B(D-OFF)] to enter set mode. c Push [SET B(D-OFF)] or [ENT C(T-OFF)] lect the desired memory channel via [DIAL]. MW w Push [SET LOCK ] enter the set mode. several times until “BAK” appears. e Push [SET] or [MONI] several times until “BAK” appears. v Push [Y] or [Z] to select the desired bank Y Z • “– –” indication blinks as follows. to be set. [Y]/[Z] b Push [CLR A(MW)] to set the channel into DIGITAL PRIO AO BUSY the bank and exit set mode. MUTE NAR MID n Repeat steps z to b to set an another LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW memory channel into the same or another bank. r Rotate [DIAL] to select the desired bank to be set. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW [DIAL] t Push any key other than [SET] or [MONI] to set the chan- nel into the bank and return to regular memory condition. y Repeat steps q to t to set another memory channel into the same or another bank. 33
  • 5 MEMORY OPERATION I Transferring bank contents y Repeat steps q to t for transferring or erasing an an- Contents of programmed memory banks can be cleared or transferred to another bank. other banks contents. INFORMATION: Even if the memory bank contents are z Select the desired bank contents to be trans- cleared, the memory channel contents still remain pro- BANK ferred or erased. 5 grammed. ➥ Push [MR/CALL] to select memory mode. ➥ Push [BANK/OPTION], then select the de- q Select the desired bank contents to be transferred or erased. SET YZ sired memory bank via [Y]/[Z]. ➥ Push [M/CALL PRIO ] to select memory mode. ➥ Push [CLR A(MW)] to select the bank then ➥ Push [BANK OPT ] then rotate [DIAL] to select the de- YZ select the desired contents via [Y]/[Z]. sired memory bank. [Y]/[Z] x Push [SET B(D-OFF)] to enter set mode. • Bank initial blinks. c Push [SET B(D-OFF)] or [ENT C(T-OFF)] sev- ➥ Push [BANK OPT ] to select the bank then rotate eral times until “BAK” appears. [DIAL] to select the desired contents. v Push [Y]/[Z] to select the desired bank initial YZ • Bank initial stops blinking. w Push [SET LOCK ] enter the set mode. to transfer or erase. e Push [SET] or [MONI] several times until “BAK” appears. • Select “-- --” indication when erasing the contents from the bank. • Bank initial appears. b Push [CLR A(MW)] to set the bank and exit set DIGITAL PRIO AO BUSY mode. MUTE NAR MID n Repeat steps z to b for transferring or eras- LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW ing an another banks contents. r Rotate [DIAL] to select the desired bank initial to transfer or erase. • Select “– –” indication when erasing the contents from the bank. t Push any key other than [SET] or [MONI] to transfer or erase. and return to regular memory condition. 34
  • 6 CALL CHANNEL OPERATION I Call channel selection I Call channel transferring ➥ Push [M/CALL PRIO ] once q Push [M/CALL PRIO ] several times to select the call or twice to select the call channel. • “C” appears. channel. w Push [S.MW MW ] momentarily, then rotate [DIAL] to se- • “C” appears instead of mem- ory channel number indication. lect the memory channel to transfer the contents to. Appears • Push [M/CALL PRIO ] to re- • “M” indicator and memory channel number blink. turn to memory mode, or push • To transfer to the VFO, push [S.MW MW ] for 1 sec. DIGITAL PRIO AO BUSY MUTE [V/MHz SCAN ] to select VFO e Push [S.MW MW ] for 1 sec. to transfer when a momen- NAR MID mode. LOW tary push was used in the previous step. LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW • If channel names have been programmed into the call channel, the names are also transferred. z Push [MR/CALL] for 1 sec. to select the call MR/CALL channel. ➥ Push [MR/CALL] for 1 sec. to select the call x Push [FUNC], [CLR A(MW)] momentarily, MR/CALL channel. YZ then push [Y]/[Z] to select the memory MW • Push [MR/CALL] to select memory mode, or push channel to transfer the contents to. [VFO/LOCK] to select VFO mode. • To transfer to the VFO, push [FUNC], then push [CLR A(MW)] for 1 sec. [Y]/[Z] c Push [FUNC], then [CLR A(MW)] for 1 sec. to transfer when a momentary push was used in ✔INFORMATION the previous step. When the VFO mode is se- • If channel names have been programmed into the Small “c” shows VFO was selected from the call channel. lected from the call channel, call channel, the names are also transferred. a small “c” appears instead DIGITAL PRIO AO BUSY MUTE of memory channel number. NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 35
  • 6 CALL CHANNEL OPERATION I Programming a call channel r Push [S.MW MW ] for 1 sec. to program. Operating frequency, duplex information, subaudible tone in- • 3 beeps sound and the unit returns to VFO mode automatically. formation (tone encoder or tone squelch ON/OFF and its fre- quency) and alphanumeric channel names can also be z Set the desired frequency in VFO mode. programmed into the call channel. ➥ Push [VFO/LOCK] to select VFO mode. VFO/CALL ➥ Set the frequency. q Set the desired frequency in VFO mode. ➥ Set other data as desired. ➥ Push [V/MHz SCAN ] to select VFO mode. 6 MW x Push [FUNC], then [CLR A(MW)] momentarily. ➥ Set the frequency using [DIAL]. c Select the call channel via [Y] or [Z]. ➥ Set other data as desired. Y Z v Push [FUNC] then [CLR A(MW)] for 1 sec. to w Push [S.MW MW ] momentarily. [Y]/[Z] e Rotate [DIAL] to select the call channel program. • 3 beeps sound and the unit returns to VFO mode • “M” indicator and “C” blink. automatically. [EXAMPLE]: Programming 145.120 MHz into the call channel via the microphone. Set the frequency. Push to select VFO mode. Push , then momentarily. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM ANM SCAN DUP DUP DUP SET SET SET TONE M/CALL TONE M/CALL TONE M/CALL V/ MHz V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW ➠ Push until large “C” appears. Push then for 1 sec. “ “Beep DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE “ Beep NAR NAR NAR MID MID MID “ Beep LOW LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP “ SET TONE M/CALL V/ MHz LOW SET SET MONI TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW 36
  • 7 SCAN OPERATION I Scan types Scanning searches for signals automatically and makes it There are 3 scan types and 4 resume conditions to suit your easier to locate new stations for contact or listening purposes. operating needs. Repeatedly scans all frequen- Repeatedly scans between FULL SCAN (p. 38) PROGRAMMED SCAN cies over the entire band. two user-programmed fre- (p. 38) Used as the simplest scan quencies. Used for checking Band Band edge edge without any preliminary set- for frequencies within a speci- Band Scan edges Band tings necessary. fied range such as repeater edge edge Scan output frequencies, etc. 3 Scan pairs of scan edges are avail- able. Jump Jump Repeatedly scans memory 4 resume conditions are avail- MEMORY SCAN (p. 38) SCAN RESUME channels except those set as able: 3 timer scans and pause CONDITION (p. 42) skip channels. Used for often- scan. When receiving a sig- SKIP called channels and for by- nal, pause scan pauses until Receiving a signal M1 M2 M3 passing normally busy the signal disappears; timer Pause channels such as repeater scans pause for 5, 10 or M0 scan M4 frequencies. 15 sec. SKIP 2 sec. M 199 M6 M5 Timer scan Pausing NOTE: A tone scan function is available to search for subaudible tones (e.g. when you want to find a subaudible tone fre- quency necessary to open a repeater). See p. 51 for details. 37
  • 7 SCAN OPERATION I Scan start/stop D Preparation z Push [VFO/LOCK] to select VFO mode for Scan resume condition (p. 42); program the scan edges SCAN full/programmed scan; push [MR/CALL] to se- (pgs. 39, 40); program 2 or more memory channels (pgs. 25, 2 lect memory mode for memory scan. 26); set skip settings, if desired (p. 41). • Push [BANK/OPTION] to select a bank for bank SET D Operation scan. B x Set the squelch to the point where noise is just q Select VFO mode for full/programmed scan with muted. [V/MHz SCAN ]; or memory mode for memory scan with c Push [SCAN 2(T-SCAN)] to start the scan. 7 [M/CALL PRIO ]. Y Z • Push [Y] or [Z] for 1 sec. also starts the scan. • Select the desired bank with [BANK OPT ] for bank scan. v Push [SET B(D-OFF)] to switch full and pro- w Set the squelch to the point where noise is just muted. grammed scan (P1, P2 and P3). e Push [V/MHz SCAN ] for 1 sec. to start the scan. b To stop the scan push [SCAN 2(T-SCAN)] or • To change the scanning direction, rotate [DIAL]. [CLR A(MW)]. • The memory channel readout blinks the scan type as follows: r Push [SET LOCK ] to switch full and programmed scan (P1, P2 and P3). t To stop the scan, push [SET LOCK ] or [V/MHz SCAN ]. • During full scan • During programmed scan • During memory scan • During Bank scan DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE MUTE NAR NAR NAR NAR MID MID MID MID LOW LOW LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM DUP ANM DUP ANM DUP ANM SCAN DUP SET SET SET SET TONE M/CALL TONE M/CALL TONE M/CALL TONE M/CALL V/ MHz V/ MHz V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW MONI LOW ( SET ) to select full, LOCK Push Indicates scan edge channels. When AM and FM frequencies are programmed into memory band* (A1, AA) or programmed • P1 stands for 1A/1b channel disorderly, memory scan takes a lot of time (very slow). scan (P1, P2 and P3) in se- • P1 to P3 are available when Because changing mode takes a time. quence. (*Depends on versions) they are programmed, and In this case, assign AM and FM frequencies into the separate ( SET ) . A1 : FM band (136–174 MHz) LOCK switches with bank respectively. And using the bank scan is helpful. AA : AM band (118–136 MHz) 38
  • 7 SCAN OPERATION I Scan edges programming r Push [S.MW MW ] for 1 sec. to program. Scan edges can be programmed in the same manner as • 3 beeps sound and VFO is automatically selected. memory channels. Scan edges are programmed into scan • Scan edge 1b, 2b or 3b is automatically selected when continu- edges, 1A/1b to 3A/3b, in memory channels. ing to push [S.MW MW ] after programming. t To program a frequency for the other pair of scan edges, q Set the edge frequency of the desired frequency range in 1b, 2b or 3b, repeat steps q and r. VFO mode: ➥ Set the frequency using [DIAL]. • If the same frequency is programmed into a pair of scan edges, ➥ Set other data (e.g. repeater settings, etc.) if desired. programmed scan will not function. w Push [S.MW MW ] momentarily. • “M” indicator and channel number blink. e Rotate [DIAL] to select one of scan edge channel, 1A, 2A or 3A. [EXAMPLE]: Programming 145.300 MHz into scan edges 1A. S.MW MW () SCAN Push Rotate for setting frequency, etc. Push momentarily. V/ MHz DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK T-SCAN PRIO ANM SCAN LOCK ANM T-SCAN PRIO SCAN LOCK PRIO ANM T-SCAN SCAN DUP DUP DUP SET SET SET TONE M/CALL TONE M/CALL TONE M/CALL V/ MHz V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW S.MW MW Push for 1 sec. ➠ Rotate and continue to push “ “Beep DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE “ Beep NAR NAR NAR MID MID MID “ Beep LOW LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP “ SET TONE M/CALL V/ MHz LOW SET SET MONI TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW 39
  • 7 SCAN OPERATION D Programming scan edges via microphone z Set the desired frequency in VFO mode. b To program a frequency for the other scan edge channels, ➥ Push [VFO/LOCK] to select VFO mode. MW repeat steps z to v. ➥ Set the frequency via the keypad or [Y]/[Z]. YZ x Push [FUNC] then [CLR A(MW)] momentarily. c Push [Y] or [Z] to select scan edge channels, Y Z 1A, 2A or 3A. v Push [FUNC], then push [CLR A(MW)] for 1 sec. to program. • 3 beeps sound and VFO is automatically selected. 7 • Memory channel number advances to the next scan edge channel, 1b, 2b or 3b, when continuing to push [CLR A(MW)] after programming. [EXAMPLE]: Programming 145.800 MHz into scan edges 1b. Push then momentarily. Push Push DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM ANM SCAN DUP DUP DUP SET SET SET TONE M/CALL TONE M/CALL TONE M/CALL V/ MHz V/ MHz V/ MHz MONI LOW MONI LOW MONI LOW Push then 1 sec. ➠ Push and continue to push “ “Beep DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE “ Beep NAR NAR NAR MID MID MID “ Beep LOW LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP “ SET TONE M/CALL V/ MHz LOW SET SET MONI TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW 40
  • 7 SCAN OPERATION I Skip channel setting SET MODE USING z Select a memory channel. The memory skip function speeds up scanning by checking ➥ Select memory mode by pushing [MR/CALL]. SET only those memory channels not set as skip channels. Set B ➥ Push [Y] or [Z] to select the desired channel Y Z skip channels as follows. to be a skip channel. x Push [SET B(D-OFF)] to enter set mode. The display shows that DIGITAL PRIO AO BUSY MUTE memory channel 15 is c Push [SET B(D-OFF)] or [ENT C(T-OFF)] several NAR MID set as a skip channel. LOW times until “CHS” appears as shown at left. LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW v Push [Y] or [Z] to set or cancel the skip setting. Y Z • See item r at left for skip indicator details. b Push [CLR A(MW)] to exit set mode. q Select a memory channel: ➥ Push [M/CALL PRIO ] to select memory mode. NOTES: ➥ Rotate [DIAL] to select the desired channel to be a skip Even though scan edge channels cannot be set as skip channel. channels, they ARE skipped during memory scan. w Push [SET LOCK ] to enter set mode. SET mode cannot be accessed when memory names are e Push [SET] or [MONI] several times until “CHS” appears displayed. To set the scan resume condition, return to fre- as shown above. quency indication by pushing [MONI ANM ] on the front r Rotate [DIAL] to turn the skip function ON or OFF for the panel for 1 sec., or push [FUNC] then [MONI 1(ANM)] (HM- selected channel. 133V) to cancel the channel name indication, then set as • “~” appears : The channel is skipped during scan. described on this page. (CHS-ON) • “~” disappears : The channel is scanned during scan. (CHS-OFF) t Push any key other than [SET] or [MONI] to exit set mode. 41
  • 7 SCAN OPERATION I Scan resume condition SET MODE USING z Push [SET B(D-OFF)] to enter set mode. The scan resume condition can be selected as timer or pause SET x Push [SET B(D-OFF)] or [ENT C(T-OFF)] several scan. The selected resume condition is also used for priority B watch. (p. 44) times until “SCT” or “SCP” appears as shown at left. c Push [Y] or [Z] to select the scan resume condi- Y Z The display shows that DIGITAL PRIO AO BUSY MUTE the scan will resume tion. NAR MID 15 sec. after it stops. LOW • See item e at left for scan resume condition details. LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW v Push [CLR A(MW)] to exit set mode. 7 NOTE: Set mode cannot be accessed when memory names are q Push [SET LOCK ] to enter set mode. displayed. To set the scan resume condition, return to fre- w Push [SET] or [MONI] several times until “SCT” or “SCP” quency indication by pushing [MONI ANM ] on the front appears as shown above. panel for 1 sec., or push [FUNC] then [MONI 1(ANM)] (HM- • When “d” is displayed in place of the 100 MHz digit, cancel the 133V) to cancel the channel name indication, then set as DTMF memory encoder in advance. (p. 46) e Rotate [DIAL] to set the desired timer: described on this page. • “SCT-15” : Scan pauses 15 sec. while receiving a signal. • “SCT-10” : Scan pauses 10 sec. while receiving a signal. • “SCT-5” : Scan pauses 5 sec. while receiving a signal. • “SCP-2” : Scan pauses until the signal disappears and then resumes 2 sec. later. r Push any keys than [SET] or [MONI] to exit set mode. 42
  • 8 PRIORITY WATCH I Priority watch types Priority watch checks for signals on a VFO frequency every MEMORY CHANNEL WATCH 5 sec. while operating on a memory channel. The transceiver While operating on a VFO fre- 5 sec. has 3 priority watch types to suit your needs. You can transmit quency, priority watch checks for 50 msec. on the VFO frequency while the priority watch operates. a signal on the selected memory VFO Memory channel every 5 sec. frequency channel The watch resumes according to the selected scan resume condition. See previous page for details. NOTE: If the pocket beep function is activated, the trans- ceiver automatically selects the tone squelch function MEMORY SCAN WATCH when priority watch starts. While operating on a VFO fre- 50 msec. 5 sec. quency, priority watch checks for Mch 1 signals on each memory chan- Mch 2 SKIP VFO nel in sequence. Mch 3 frequency • The memory skip function is useful Mch 199 to speed up the scan. CALL CHANNEL WATCH While operating on a VFO fre- 5 sec. quency, priority watch checks for 50 msec. signals on the call channel every VFO Call 5 sec. frequency channel 43
  • 8 PRIORITY WATCH I Priority watch operation q Select VFO mode; then, set an operating frequency. z Select VFO mode; then, set an operating fre- PRIO w Set the watching channel(s). quency. 3 x Set the watching channel(s). For memory channel watch: Select the desired memory channel. For memory channel watch: Y Z For memory scan watch: Push [MR/CALL] then [Y] or [Z] to select the Select memory mode; then, push [V/MHz SCAN ] for desired memory channel. 1 sec. to start memory scan. For memory scan watch: For call channel watch: Push [MR/CALL], then push [SCAN 2] to start the Select the call channel by pushing [M/CALL PRIO ] once memory scan. or twice. For call channel watch: 8 e Push [M/CALL PRIO ] for 1 sec. to start the watch. Push [MR/CALL] for 1 sec. to select the call • The transceiver checks the memory or call channel every 5 sec. channel. • The watch resumes according to the selected scan resume con- c Push [PRIO 3(PTT-M)] to start the watch. dition. (p. 42) • The transceiver checks the memory or call channel • While the watch is pausing, pushing [M/CALL PRIO ] resumes every 5 sec. the watch manually. • The watch resumes according to the selected scan re- r Push [M/CALL PRIO ] to stop the watch. sume condition. (p. 42) • To resume the watch manually when paused, push While pausing or receiving [PRIO 3(PTT-M)] or [CLR A(MW)]. DIGITAL PRIO AO BUSY MUTE a signal on the memory or NAR v To stop the watch, push [CLR A(MW)]. MID call channel, “PRIO” blinks. LOW LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 44
  • 9 DTMF MEMORY ENCODER I Programming a DTMF code t Push [SET] or [MONI]. DTMF codes are used for autopatching, controlling other • The first digit blinks. equipment, etc. The transceiver has 16 DTMF memory chan- y Rotate [DIAL] to select the desired code. nels (d0–dF) for storage of often-used DTMF codes of up to u Push [MONI] to select the next digit. 24 digits. • Push [SET] to move the cursor backward. q Push [BANK OPT ] for 1 sec. to enter the DTMF setting. i Repeat the steps y and u to set the desired DTMF tone w Rotate [DIAL] to turn the DTMF encoder ON. sequence. e Push [SET] or [MONI] to enter the DTMF programming • The S/RF indicator shows the digit group. The indication in- creases every 6 digit. condition. o Push [V/MHz], then push any key other than indicated • Push [V/MHz] to return to the DTMF setting. r Rotate [DIAL] to select the desired DTMF memory chan- function keys to exit DTMF memory programming condi- tion. nel. • The DTMF memory channel indication blinks. [EXAMPLE]: Programming “5428AB453” into DTMF memory channel “d4.” () ( ). Rotate to turn the DTMF encoder ON. Push or Push for 1 sec. BANK OPT SET MONI DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET TONE M/CALL V/ MHz MONI LOW SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW Repeat the previous step () Rotate . Push then rotate . until the desired code is entered. SET DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW SET TONE M/CALL V/ MHz MONI LOW SET TONE M/CALL V/ MHz MONI LOW DIGITAL PRIO AO BUSY (V/MHz), then any other keys MUTE Push NAR MID than indicated function keys. LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 45
  • 9 DTMF MEMORY ENCODER I Transmitting a DTMF code D Automatic transmission (DTMF memory) Transmitting a DTMF memory directly— continued NOTE: When no DTMF code programmed chan- z Push [FUNC] then [LOW 6(DTMF)] to turn the DTMF-S nel number is pushed, it transmits previously DTMF DTMF memory encoder ON. transmitted DTMF memory code. • “d” appears in place of the 100 MHz digit. v Push [DTMF-S] again to deactivate the DTMF x Push [BANK/OPTION] for 1 sec. then memory direct selection. [SET B(D-OFF)] to enter the DTMF memory pro- b Push [FUNC] then [SET B(D-OFF)] to cancel gramming condition. the DTMF memory encoder. c Push [Y] or [Z] to select the desired channel. Y Z v Push [PTT] to transmit the selected memory. • Exit the programming condition automatically. D Manual transmission • Each push of [PTT] transmits the DTMF code. z Deactivate the DTMF memory encoder by 9 b Push [FUNC] then [SET B(D-OFF)] to cancel the DTMF-S pushing [FUNC] then [SET B(D-OFF)]. DTMF memory encoder. x Push [DTMF-S] to turn the DTMF direct selec- • When the DTMF encoder is turned ON continuously, tion ON. each push of the PTT transmits the previously se- • The function indicator (microphone) lights green. lected DTMF code. c Push one of “A” to “F” keys momentarily, then push the desired DTMF keys, 0–9 and A to F. D Transmitting a DTMF memory directly • A: [CLR A(MW)] B: [SET B(D-OFF)], z Push [FUNC] then [LOW 6(DTMF)] to turn the C: [ENT C(T-OFF)] D: [SQLY D(MUTE)], Y DTMF-S M E: [M(TONE-1)] F: [SQLZ #(16KEY-L)] DTMF memory encoder ON. Z • Automatically transmits without pushing PTT. • “d” appears in place of the 100 MHz digit. x Push [DTMF-S] to turn the DTMF memory di- • The first code, one of “A” to “F,” is not transmitted. DTMF code transmission starts from the 2nd code. rect selection ON. v Push [DTMF-S] again to deactivate the DTMF • The function indicator (microphone) lights green. direct selection. c Push the desired DTMF channel number. • “0” to “9” are available for channel numbers. • The selected DTMF code is automatically transmit- ted without pushing PTT. 46
  • 9 DTMF MEMORY ENCODER I DTMF speed INITIAL SET MODE USING The rate at which DTMF memories send individual DTMF characters can be set to accommodate operating needs. The display shows the DIGITAL PRIO AO BUSY MUTE fastest DTMF speed is NAR MID selected. LOW LOCK ANM T-SCAN PRIO SCAN DUP SET TONE M/CALL V/ MHz MONI LOW q Push [PWR] for 1 sec. to turn power OFF. w While pushing [SET LOCK ], push [PWR] for 1 sec. to turn power ON and enter initial set mode. e Push [SET] or [MONI] several times until “DTD” appears as shown above. r Rotate [DIAL] to select the desired speed as shown in the table below. t Push [PWR] to exit initial set mode. DISPLAY INTERVAL SPEED DTD-- 1 100 msec. 5.0 cps DTD-- 2 200 msec. 2.5 cps DTD-- 3 300 msec. 1.6 cps DTD-- 5 500 msec. 1.0 cps cps=characters/sec 47
  • 10 POCKET BEEP AND TONE SQUELCH I Pocket beep operation u Push [TONE T-SCAN ] several times until “ This function uses subaudible tones for calling and can be ” or “ ” used as a “common pager” to inform you that someone has are displayed to turn ON the pocket beep with tone called while you were away from the transceiver. squelch or DTCS squelch, respectively. D Waiting for a call from a specific station DIGITAL PRIO AO BUSY MUTE NAR q Set the operating frequency. MID LOW LOCK PRIO ANM T-SCAN SCAN DUP w Push [SET LOCK ] to enter set mode. SET TONE M/CALL V/ MHz MONI LOW e Push [SET] or [MONI] several times until “Ct” for tone squelch or “dt” for DTCS squelch appears. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MID MID MUTE MUTE LOW LOW NAR NAR LOCK T-SCAN PRIO ANM SCAN LOCK T-SCAN PRIO SCAN DUP ANM DUP 9 MID MID SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW Appears when the pocket beep Appears when the pocket beep 10 Tone squelch frequency setting DTCS code setting with tone squelch is activated. with DTCS squelch is activated. i When a signal with the matched tone is received, the r Rotate [DIAL] to select the desired tone squelch frequency transceiver emits beep tones and blinks “ ”. or DTCS code. • Beep tones sound for 30 sec. and “ ” blinks. To stop the beeps t When operating the pocket beep function with DTCS and blinking manually, push any key. When the beep tones are squelch, push [SET] once then rotate [DIAL] to select the not stopped manually, “ ” continues flashing until step o is DTCS polarity. operated. o Push [PTT] to answer. DIGITAL PRIO AO BUSY MUTE NAR • “ ” disappears and cancels the pocket beep function automati- MID LOW cally. LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW !0 Push [TONE T-SCAN ] several times until “ ” or “ ” dis- appears to cancel the tone squelch or DTCS squelch func- DTCS polarity setting tion. y Push any key other than [SET] or [MONI] to exit set mode. 48
  • 10 POCKET BEEP AND TONE SQUELCH D Available tone frequency list Waiting for a call from a specific station—continued z Set the operating frequency. 67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1 TSQLS x Program the CTCSS tone frequency or DTCS 69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6 71.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.8 code in set mode. 74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3 ➥ Push [SET B(D-OFF)] to enter set mode. 77.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1 DTCSS ➥ Push [SET B(D-OFF)] or [ENT C(T-OFF)] several times until “Ct” for tone squelch or NOTE: The transceiver has 50 tone frequencies and con- “dt” for DTCS squelch appears. sequently their spacing is narrow compared to units having • “ ” blinks when tone squelch (“Ct”), or “ ” 38 tones. Therefore, some tone frequencies may receive blinks when DTCS squelch (“dt”) is selected. interference from adjacent tone frequencies. ➥ Push [Y]/[Z] to select the desired tone YZ To prevent interference from adjacent tone frequencies, frequency or DTCS code. using the frequencies as in the following table, is recom- ➥ Push [SET B(D-OFF)] to select “DTP” then mended. YZ push [Y]/[Z] to select the DTCS polarity. ➥ Push [CLR A(MW)] to exit set mode. • Recommended tone frequencies c Push [FUNC] then push [DUP+ 8(TSQLS)] S 67.0 77.0 88.5 100.0 114.8 131.8 151.4 173.8 203.5 233.6 S or [MID 5(DTCSS)] to turn ON the pocket 69.3 79.7 91.5 103.5 118.8 136.5 156.7 179.9 210.7 241.8 71.9 82.5 94.8 107.2 123.0 141.3 162.2 186.2 218.1 250.3 beep with tone squelch or DTCS squelch, re- 74.4 85.4 97.4 110.9 127.3 146.2 167.9 192.8 225.7 spectively. v When a signal with the matched tone is re- ceived, the transceiver emits beep tones for D Calling a waiting station using pocket beep 30 sec. and blinks “ ”. A subaudible tone matched with the station’s CTCSS tone fre- b Push [PTT] to answer or push [CLR A(MW)] quency or 3-digit DTCS code with polarity is necessary. Use to stop the beeps and flashing. the tone squelch on the next page or a subaudible tone en- • “ ” disappears and cancels the pocket beep func- coder (pgs. 19, 50) tion automatically. n To cancel the tone squelch or DTCS squelch function, push [FUNC] then [ENT C(T-OFF)]. • “ ” or “ ” disappears 49
  • 10 POCKET BEEP AND TONE SQUELCH I Tone/DTCS squelch operation z Set the operating frequency. The tone or DTCS squelch opens only when receiving a sig- TSQL x Program the CTCSS tone frequency or DTCS nal with the same pre-programmed subaudible tone or DTCS code, respectively. code in set mode. • See p. 49 for programming details. DTCS c Push q Set the operating frequency. [FUNC] then [SIMP 9(TSQL)] or w Program the CTCSS tone frequency or DTCS code in set [HIGH 4(DTCS)] to turn the tone squelch or DTCS mode. squelch ON. v When a signal with the matched tone is received, • See p. 48 for programming details. e Push [TONE T-SCAN ] several times until “ ” or “ ” ap- the squelch opens and the signal can be heard. pears in the function display. • When the received signal includes an unmatched • “ ” for tone squelch; “ ” for DTCS squelch operation. tone, the squelch does not open. However, the S/RF r When a signal with the matched tone is received, the indicator shows the received signal strength. • To open the squelch manually, push [MONI 1(ANM)]. squelch opens and the signal can be heard. 10 b Operate the transceiver in the normal way (push • When the received signal includes an unmatched tone, the [PTT] to transmit; release [PTT] to receive. squelch does not open. However, the S/RF indicator shows the n To cancel the tone squelch, push [FUNC] then received signal strength. • To open the squelch manually, push [MONI ANM ]. [ENT C(T-OFF)]. t Operate the transceiver in the normal way (push [PTT] to • “ ” or “ ” disappears transmit; release [PTT] to receive). y To cancel the tone squelch, push [TONE T-SCAN ] sev- eral times until “ ” or “ ” disappears. 50
  • 10 POCKET BEEP AND TONE SQUELCH I Tone scan r When the CTCSS tone frequency or 3-digit DTCS code is By monitoring a signal that is being operated with pocket beep, tone or DTCS squelch function, you can determine the matched, the squelch opens and the tone frequency is tone frequency or DTCS code necessary to open a squelch. temporarily programmed into the selected condition such as memory or call channel. q Set the channel to be checked for a tone frequency or • The tone scan pauses when a CTCSS tone frequency or 3-digit code. DTCS code is detected. w Push [TONE T-SCAN ] several times to select the tone • The decoded CTCSS tone frequency or 3-digit DTCS code is used for the tone encoder or tone encoder/decoder depending condition or type to be scanned. on the selected tone condition or type in step w. • One of “ ,” “ ” or “ ” appears - No indication : Cannot be used for operation. e Push [TONE T-SCAN ] for 1 sec. to start the tone scan. -“ ” : CTCSS tone encoder • To change the scanning direction, rotate [DIAL]. -“ ” : CTCSS tone encoder/decoder -“ ” : DTCS tone encoder/decoder DIGITAL PRIO AO BUSY MUTE t Push [V/MHz SCAN ] to stop the scan. NAR MID LOW LOCK ANM T-SCAN PRIO SCAN DUP SET TONE M/CALL V/ MHz MONI LOW z Set the channel to be checked for a tone fre- T-SCAN quency. x Selects the tone condition or type to be DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE scanned. NAR NAR MID MID LOW LOW • Push [FUNC] then push; [DUP– 7(TONE)] for re- LOCK PRIO PRIO ANM T-SCAN SCAN LOCK T-SCAN SCAN DUP ANM DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW peater tone; [SIMP 9(TSQL)] for tone squelch; [HIGH 4(DTCS)] for DTCS squelch. During CTCSS tone scan During DTCS code scan c Push [FUNC] then [SCAN 2(T-SCAN)] to start the tone scan. v When the tone frequency is matched, the NOTE: The decoded tone frequency is programmed tem- squelch opens and the tone frequency is pro- porarily when a memory or call channel is selected. How- grammed into the selected mode such as ever, this will be cleared when the memory/call channel is memory or call channel. b Push [CLR A(MW)] to stop the scan. re-selected. 51
  • 11 PAGER/CODE SQUELCH Required Optional UT-108 I Pager function I Code programming D Before programming This function uses DTMF codes for paging and can be used as a “message pager” to inform you of a caller’s identification The pager and code squelch functions require ID codes and a even when you leave the transceiver temporarily unattended. group code. These codes are 3-digit DTMF codes and must be written into the code channels before operation. Pager selective code (push [PTT]) q Decide the ID code of each transceiver and a group code for your group. w Decide whether you want to return to normal operation or Beep Beep Beep code squelch operation after a connection is made. e Program the ID code, group code and transmit codes (other station’s codes) as below. D Code channel assignment Answer back (manual) 10 ID OR CODE CHANNEL “RECEIVE ACCEPT” OR GROUP CODE NUMBER “RECEIVE INHIBIT” 11 Your ID code 0 “Receive accept” only eep pB Bee Beep Other parties’ “Receive inhibit” should be 1–6 ID code programmed in each channel. “Receive accept” must be Group code One of 1–6 programmed. Set both transceivers to either code squelch or Memory space* P “Receive inhibit” only. non-coded operation *Channel CP automatically memorizes an ID code when receiving a pager call. The contents in channel CP cannot be changed manually. Communication 52
  • 11 PAGER/CODE SQUELCH D Code programming y Push [MONI] (or [SET]) to select 2nd digit, then rotate An ID code MUST be programmed into code channel C0. Up [DIAL] to set the desired code. to 6 transmit codes are programmable into code channels, C1 • 2nd digit blinks (1st digit stop blinking). to C6, if required. • Repeat this step for 3rd digit programming. q Push [BANK OPT ] for 1 sec. then rotate [DIAL] to turn DIGITAL PRIO AO BUSY Pager mode ON. MUTE NAR MID • “PG” appears. LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW DIGITAL PRIO AO BUSY MUTE NAR u Push [MONI] (or [SET]) to program the ID code. MID LOW LOCK T-SCAN PRIO ANM SCAN DUP • Long beep sounds and the “C0” indication blinks. SET TONE M/CALL V/ MHz MONI LOW i Rotate [DIAL] to select a transmit code channel from “C1” to “C6.” w Push [SET] or [MONI]. o Repeat steps r to u to set transmit code channel. • One of either “CP” or “C0” to “C6” flashes. !0 Push [S.MW MW ] to set the channel for “receive inhibit” • “C0” is the ID code and “C1” to “C6” are transmit codes. or “receive accept.” e Rotate [DIAL] to select code channel C0. • When “receive inhibit” is set, “SKIP” appears as follows. • A different ID code must be programmed into each transceiver. • Code channel C0 cannot be set as “receive inhibit.” • See p. 54 for “receive accept” and “receive inhibit” details. DIGITAL PRIO AO BUSY MUTE NAR MID DIGITAL PRIO AO BUSY LOW MUTE LOCK PRIO ANM T-SCAN SCAN DUP NAR SET TONE M/CALL V/ MHz MONI LOW MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW r Push [MONI] (or [SET]) to set into code programming condi- Appears when “receive inhibit” tion. is set to the code channel. • The 1st digit blinks and “C0” indication stops blinking. t Rotate [DIAL] to set the desired code. !1 Push any key other than indicated function keys to exit code set mode. 53
  • 11 PAGER/CODE SQUELCH z Push [BANK/OPTION] for 1 sec. then • Receive accept/receive inhibit ➥ “Receive accept” (“SKIP” indicator does not appear) ac- BANK/OPTION Y Z push [Y] or [Z] to turn Pager mode ON. x Push [SET B(D-OFF)] to enter to the code cepts pager calls when the transceiver receives a signal with a code the same as that in the code channel. set mode. ➥ “Receive inhibit” (“SKIP” indicator appears) rejects calls • One of either “CP” or “C0” to “C6” blinks. • “C0” is the ID code and “C1” to “C6” are the even when the transceiver receives a code the same as transmit code. that in the code channel. Transmit codes should therefore c Push [Y] or [Z] to select the desired code Y Z be programmed for “receive inhibit,” otherwise the trans- channel. ceiver will not reject unnecessary calls. v Enter the desired 3-digit code via the key- • Pager/code squelch operation during channel indication pad. b Push [SET B(D-OFF)] to set the channel To use these functions in channel indication, the pager/code squelch setting must be programmed with other memory con- for “receive inhibit” or “receive accept.”. • When “receive inhibit” is set, “SKIP” appears. tents before selecting channel number indication. • Code channel C0 cannot be set as “receive in- hibit.” • See right above for “receive accept” and “re- 11 ceive inhibit” details. n Repeat steps c to b to set additional code channels, if desired. m Push [CLR A(MW)] to exit code set mode. 54
  • 11 PAGER/CODE SQUELCH I Pager operation D Calling a specific station z Program the desired code channel in ad- q Program the desired code channel in advance (p. 53). BANK/OPTION vance (p. 54). w Set the operating frequency. x Set the operating frequency. • Set the [VOL] and [SQL] to the desired level as in normal opera- c Push [BANK/OPTION] for 1 sec. then tion. YZ push [Y]/[Z] to turn Pager mode ON. e Push [BANK OPT ] for 1 sec. then rotate [DIAL] to turn v Select the desired transmit code channel: Pager mode ON. ➥ Push [SET B(D-OFF)]. r Select the desired transmit code channel: ➥ Push [Y]/[Z] to select the code chan- YZ ➥ Push [SET] or [MONI]. nel. ➥ Rotate [DIAL] to select the code channel. ➥ Push [CLR A(MW)] to return to the pager ➥ Push any key other than indicated function keys to return operating condition. to the pager operating condition. b Push [PTT] to transmit the pager code. • 100 MHz digit shows “P.” n Wait for an answer back. DIGITAL PRIO AO BUSY MUTE • When the transceiver receives an answer back NAR MID code, the function display shows the other LOW LOCK PRIO ANM T-SCAN SCAN DUP member’s ID or group code. SET TONE M/CALL V/ MHz MONI LOW m After confirming a connection, push t Push [PTT] to transmit the pager code. [BANK/OPTION] for 1 sec. then push • Transmits the selected transmit codes and your ID automatically. y Wait for an answer back. YZ [Y]/[Z] to select the code squelch opera- • When the transceiver receives an answer back code, the func- tion, or repeat the previous key operation tion display shows the other member’s ID or group code. again to select non-selective calling sys- u After confirming a connection, push [BANK OPT ] for tem. 1 sec. then turn the [DIAL] to select the code squelch op- , Communicate with the other party as nor- eration, or repeat the previous key operation again to se- mal: push [PTT] to transmit; release to re- lect non-selective calling system. ceive. i Communicate with the other party as normal: push [PTT] to transmit; release to receive. 55
  • 11 PAGER/CODE SQUELCH D Waiting for a call from a specific station q Set the operating frequency. • PERSONAL CALLS This display appears when w Push [BANK OPT ] for 1 sec then rotate [DIAL] to turn DIGITAL PRIO AO BUSY you are called with your ID MUTE Pager mode ON. NAR MID code and the calling station’s LOW • 100 MHz digit shows “P.” LOCK T-SCAN PRIO ANM SCAN DUP ID code is 424. SET TONE M/CALL V/ MHz MONI LOW e Wait for a call. CP and blink. • When receiving a call, the caller’s ID or group code appears as shown at right. r Push [PTT] to send an answer back call and display the • GROUP CALLS operating frequency. This display appears when t After confirming a connection, push [BANK OPT ] for DIGITAL PRIO AO BUSY you are called with the group MUTE NAR 1 sec. then rotate [DIAL] to select code squelch operation, MID code, 888, and 888 has been LOW LOCK T-SCAN PRIO ANM SCAN DUP or repeat the previous key operation again to select non- programmed into code chan- SET TONE M/CALL V/ MHz MONI LOW nel C6. selective calling system. Code channel z Set the operating frequency. BANK/OPTION x Push [BANK/OPTION] for 1 sec. then 11 • ERROR INFORMATION YZ push [Y]/[Z] to turn Pager mode ON. When the transceiver re- • 100 MHz digit shows “P.” DIGITAL PRIO AO BUSY ceives an incomplete signal, MUTE c Wait for a call. NAR MID “E” and previously received LOW • When receiving a call, the caller’s ID or group LOCK PRIO ANM T-SCAN SCAN DUP code appear. SET TONE M/CALL V/ MHz MONI LOW code appears as shown at right. • DO NOT push any digit keys while code chan- Previously received code. nels C0 to C6 are displayed, or code channel contents will be changed. v Push [PTT] to send an answer back call and display the operating frequency. b After confirming a connection, push [BANK/OPTION] for 1 sec. to select code squelch operation, or repeat the previous key operation again to select non-selective 56 calling system.
  • 11 PAGER/CODE SQUELCH I Code squelch z Set the operating frequency. Code squelch provides communications with quiet standby BANK/OPTION x Push [BANK/OPTION] for 1 sec. then since you will only receive calls from stations which know YZ push [Y]/[Z] to select code squelch mode. your ID or group code. Each push of [PTT] sends a 3-digit • “CS” appears. code in order to open the receiving station’s code squelch c Select the desired transmit code channel: prior to voice transmission. ➥ Push [SET] or [MONI]. ➥ Push [Y]/[Z]. q Set the operating frequency. YZ ➥ Push [CLR A(MW)] to return to previous • Set the AF and squelch to the desired level as in normal opera- tion. condition. w Push [BANK OPT ] for 1 sec. then rotate [DIAL] to select v Communicate with the other party as nor- code squelch mode. mal: push [PTT] to transmit; release to re- • “CS” appears. ceive. e Select the desired transmit code channel: b To cancel the code squelch, push ➥ Push [SET] or [MONI]. [BANK/OPTION] for 1 sec then rotate ➥ Rotate [DIAL] to select the code channel. [DIAL]. ➥ Push any other keys than indicated function keys to exit code set mode. • 100 MHz digit shows “C.” DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW r Operate the transceiver in the normal way (push [PTT] to transmit; release [PTT] to receive). t To cancel the code squelch, push [BANK OPT ] for 1 sec. then rotate [DIAL]. • 100 MHz digit shows “1” when the function is cancelled. 57
  • 12 DIGITAL MODE OPERATION Required Optional UT-115 I Digital mode operation The IC-2200H with optional digital unit UT-115 can be oper- DIGITAL PRIO AO BUSY MUTE ated for digital voice mode and slow data operation for both NAR MID transmit and receive. Also available for connecting GPS re- LOW LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW ceiver (compatible with an RS-232C output/NMEA for- w Rotate [DIAL] to select the desired call sign channel then mat/4800 bps) and transmit/receive position data. push [SET] or [MONI]. NOTE: Digital mode operation MUST be set AM/FM mode DIGITAL PRIO AO BUSY MUTE selection to “FM” and Wide/Narrow setting to ”Wide’ in set NAR MID LOW mode. (pgs. 74, 78) LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW e Push [MONI] (or [SET]) to set into call sign programming condition. I Call sign programming • The 1st digit blinks and channel indication stops blinking. r Rotate [DIAL] to set the desired character or code. • Push [MONI] or [SET] to move the cursor to left or right, re- 4 kind of call sign memories are available for your own call 11 spectively. sign “MYC,” other station call sign “YUC” and nearest re- t Push [MONI] (or [SET]) to select 2nd digit, then rotate 12 peater call sign “R1C” and another zone’s repeater call sign [DIAL] to set the desired character or code. “R2C.” Each call sign memory can be stored up to 6 call • 2nd digit blinks (1st digit stop blinking). signs, and each call sign programmed up to 8 characters. • Repeat this step for programming your call sign. D Your call sign programming DIGITAL PRIO AO BUSY MUTE NAR Your call sign must be programmed for both Digital voice and MID LOW LOCK T-SCAN PRIO ANM SCAN DUP slow data communications (including GPS transmission). SET TONE M/CALL V/ MHz MONI LOW y Push [V/MHz] to fix the call sign. q Push [BANK OPT ] for 1 sec. then push [BANK OPT ] or u Rotate [DIAL] to select an another channel from “C1” to [V/MHz] several times to select the call sign select mode. “C6.” • “MYC” appears. i Repeat steps w to y to program your call sign channels. 58
  • 12 DIGITAL MODE OPERATION D Station/Repeater1/2 call sign programming Your call sign programming—continued Station call sign must be programmed for the specified sta- z Push [BANK/OPTION] for 1 sec. then tion call as well as repeater operation in both Digital voice and BANK/OPTION push [BANK/OPTION] or [MR/CALL] to slow data communications. select the call sign select mode. • “MYC” appears. q Push [BANK OPT ] for 1 sec. then push [BANK OPT ] or x Push [Y] or [Z] to select the desired call Y Z [V/MHz] several times to select the call sign select mode. sign channel then push [SET B(D-OFF)]. • “YUC” appears for station call sign. c Push [SET B(D-OFF)] to set into call sign • “R1C” or “R2C” appears for repeater call sign. programming mode. • The 1st digit blinks and channel indication DIGITAL PRIO AO BUSY MUTE NAR stops blinking. MID LOW v Push [Y] or [Z] to set the desired charac- Y Z LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW ter or code. w Rotate [DIAL] to select the desired call sign channel then • Push [SET B(D-OFF)] or [ENT C(T-OFF)] to push [SET] or [MONI]. move the cursor to left or right, respectively. b Push [SET B(D-OFF)] or [ENT C(T-OFF)] to DIGITAL PRIO AO BUSY Y Z MUTE select 2nd digit, then push [Y] or [Z] to set NAR MID the desired character or code. LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW • 2nd digit blinks (1st digit stops blinking). • Repeat this step for programming your call e Push [MONI] (or [SET]) to set into call sign programming con- sign. dition. n Push [CLR A(MW)] to fix the call sign and • The 1st digit blinks and channel indication stops blinking. exit programming condition. r Rotate [DIAL] to set the desired character or code. • Push [MONI] or [SET] to move the cursor to left or right, re- spectively. 59
  • 12 DIGITAL MODE OPERATION t Push [MONI] (or [SET]) to select 2nd digit, then rotate z Push [BANK/OPTION] for 1 sec. then BANK/OPTION [DIAL] to set the desired character or code. push [BANK/OPTION] or [MR/CALL] to • 2nd digit blinks (1st digit stop blinking). select the call sign select mode. • Repeat this step for programming station/repeater call sign. • “YUC” appears for station call sign. • “R1C” or “R2C” appears for repeater call sign. DIGITAL PRIO AO BUSY x Push [Y] or [Z] to select the desired call Y Z MUTE NAR MID sign channel then push [SET B(D-OFF)]. LOW LOCK T-SCAN PRIO ANM SCAN DUP c Push [SET B(D-OFF)] to set into call sign SET TONE M/CALL V/ MHz MONI LOW programming mode. y Push [V/MHz] to fix the call sign. • The 1st digit blinks and channel indication u Rotate [DIAL] to select an another channel from “C1” to stops blinking. “C6.” v Push [Y] or [Z] to set the desired charac- Y Z i Repeat steps w to y to program another station/repeater ter or code. call sign channels. • Push [SET B(D-OFF)] or [ENT C(T-OFF)] to move the cursor to left or right, respectively. b Push [SET B(D-OFF)] or [ENT C(T-OFF)] to ✔ For your information: Y Z select 2nd digit, then push [Y] or [Z] to set Station and/or repeater call sign can be programmed from the desired character or code. Received call record when a call is received. 12 • 2nd digit blinks (1st digit stops blinking). See page 64 for details. • Repeat this step for programming your call sign. ✔ For your information: n Push [CLR A(MW)] to fix the call sign and exit programming condition. Repeater call sign can be programmed gateway connection capabilities at step r for connecting to the other Area or NOTE: The digital repeater for an amateur radio operation is Zone. not available at present of December 2003. It will be de- • “G” appears or disappears at the 8th digit when each pushing [LOW]. signed in the future. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 60
  • 12 DIGITAL MODE OPERATION I Digital voice mode operation q Set the desired frequency in VFO mode. (pgs. 9, 10) D When sending a CQ • Select output power, if desired. (p.15) y Select “CQ” as the call sign. w Push [BANK OPT ] for 1 sec. then push [BANK OPT ] or - Push [BANK OPT ] twice to select the call sign select [V/MHz] several times to select the digital select mode. mode. • “DG” appears. • “YUC” appears. e Rotate [DIAL] to turn the digital mode ON. - Rotate [DIAL] to select the desired channel then push Appears [SET] or [MONI]. - Push [S.MW MW ] for 1 sec. to edit “CQCQCQ.” DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR MID MID DIGITAL PRIO AO BUSY LOW LOW MUTE LOCK ANM T-SCAN PRIO SCAN LOCK PRIO DUP ANM T-SCAN SCAN DUP NAR SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW MID LOW r Push [BANK OPT ] to select the your call sign select mode. LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW • “MYC” appears. t Rotate [DIAL] to select the desired your call sign channel, if you have programmed several call signs. n Select “CQ” as the call sign. z Set the desired frequency in VFO mode. BANK/OPTION - Push [BANK/OPTION] twice to select the • Select output power, if desired. (p.15) BANK/OPTION call sign select mode. x Push [BANK/OPTION] for 1 sec. then • “YUC” appears. push [BANK/OPTION] or [MR/CALL] to Y Z - Push [Y] or [Z] to select the desired select the digital select mode. channel then push [SET B(D-OFF)] or • “DG” appears. [ENT C(T-OFF)]. c Push [Y] to turn the digital mode ON. Y - Push [FUNC] then [CLR A(MW)] for 1 v Push [BANK/OPTION] to select the your sec. to edit “CQCQCQ.” call sign select mode. • “MYC” appears. b Push [Y] or [Z] to select the desired your Y Z call sign channel, if you have programmed several call signs. 61
  • 12 DIGITAL MODE OPERATION D When calling the desired station n Select the desired call sign. y Select the desired call sign. BANK/OPTION - Push [BANK/OPTION] twice to select the - Push [BANK OPT ] twice to select the call sign select mode. call sign select mode. • “YUC” appears. • “YUC” appears. - Rotate [DIAL] to select the desired call sign (pre-pro- Y Z - Push [Y] or [Z] to select the desired call grammed), or set the desired call sign. (see pgs. 59, 60) sign (pre-programmed), or set the desired DIGITAL PRIO AO BUSY call sign. (see p. 60) MUTE NAR MID - Push [CLR A(MW)] to exit option set LOW LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW mode. m Push and hold [PTT] to transmit and speak - Push any key other than indicated function keys to exit option set mode. into the microphone at normal voice level. • Transmit indicator appears and the RF meter DIGITAL PRIO AO BUSY MUTE shows the output power. NAR MID , Release [PTT] to return to receive. LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW • The other station call sign will be received. • Received call signs can be stored into the re- uPush and hold [PTT] to transmit and speak into the micro- ceived call record automatically. See page 63 12 for details. phone at normal voice level. • Transmit indicator appears and the RF meter shows the output power. i Release [PTT] to return to receive. • The other station call sign will be received. • Received call signs can be stored into the received call record automatically. See page 63 for details. NOTE: The digital mode operation is vastly different than FM mode. One of the differences is in the digital mode the squelch does not function as FM mode, changing the squelch setting will not open to hear the hiss of “White Noise,” only activate for digital squelch function as CSQL (Digital code squelch), DSQL (Call sign squelch) or S-meter squelch. 62
  • 12 DIGITAL MODE OPERATION I When receiving a Digital call z Push [BANK/OPTION] for 1 sec. then When an individual station call is received, the calling station BANK/OPTION call sign can be stored into the received call record. push [BANK/OPTION] or [MR/CALL] to The record is cleared once turning power OFF. select the received call indication. • “RXCALL,” “R1CALL,” and “R2CALL” are avail- D Received call record able for the received station call sign, repeater 1/2 call signs, respectively. q Push [BANK OPT ] for 1 sec. then push [BANK OPT ] or x To confirm the received call, push [V/MHz] several times to select the received call indication. [SET B(D-OFF)] or [ENT C(T-OFF)] to enter • “RXCALL,” “R1CALL,” and “R2CALL” are available for the re- the received call sign indication mode. ceived station call sign, repeater 1/2 call signs, respectively. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM T-SCAN PRIO SCAN DUP SET TONE M/CALL V/ MHz MONI LOW w To confirm the received call, push [SET] or [MONI] to enter the received call sign indication mode. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 63
  • 12 DIGITAL MODE OPERATION D To reply a call q Push [BANK OPT ] or [V/MHz] several times to select the z Push [BANK/OPTION] or [MR/CALL] to call sign select mode. BANK/OPTION select the call sign select mode. • “YUC” appears for station call sign. • “R1C” or “R2C” appears for repeater call sign. • “YUC” appears for station call sign. • “R1C” or “R2C” appears for repeater call sign. DIGITAL PRIO AO BUSY x Push [Y] or [Z] to select the blank chan- Y Z MUTE NAR MID nel or erasable channel. LOW LOCK PRIO ANM T-SCAN SCAN DUP c Push [BANK/OPTION] three times to select SET TONE M/CALL V/ MHz MONI LOW the received call indication. v To confirm the received call, push w Rotate [DIAL] to select the blank channel or erasable [SET B(D-OFF)] or [ENT C(T-OFF)] to enter channel. the received call sign indication mode. b Push [FUNC] then [CLR A(MW)] for 1 sec. DIGITAL PRIO AO BUSY MUTE NAR to store the call sign into the selected sta- MID LOW tion call sign channel. LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW n Push and hold [PTT] to reply a call. 12 e Push [BANK OPT ] three times to select the received call in- dication. r To confirm the received call, push [SET] or [MONI] to enter the received call sign indication mode. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW tPush [S.MW MW ] for 1 sec. to store the call sign into the selected station call sign channel. yPush and hold [PTT] to reply a call. 64
  • 12 DIGITAL MODE OPERATION I Break-in communication z While receiving an another stations com- The break-in function allows you to break into an another sta- BANK/OPTION tions communications in both Digital voice and slow data op- munication, push [BANK/OPTION] for eration. 1 sec. to enter the option set mode, then set the either station/repeater call sign into q While receiving an another stations communication, push “MYC,” “YUC,” “R1C” and “R2C.” [BANK OPT ] for 1 sec. to enter the option set mode, then x Push [BANK/OPTION] or [MR/CALL] sev- set the either station/repeater call sign into “MYC,” “YUC,” eral times to select the break-in setting, “R1C” and “R2C.” then turns the break-in setting ON. w Push [BANK OPT ] or [V/MHz] several times to select the • “BRK” appears. break-in setting, then turns the break-in setting ON. c When both stations are in standby, trans- • “BRK” appears. mit to send a break-in call. • Programmed call sign station receives the DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE break-in call as well as your call sign. NAR NAR MID MID v Wait for the reply call from the station who LOW LOW LOCK ANM T-SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN DUP ANM DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW receive the break-in call. b After receive the reply call, communicate eWhen both stations are in standby, transmit to send a normal way. break-in call. n To cancel the break-in, push [BANK/OP- • Programmed call sign station receives the break-in call as well Y Z TION] for 1 sec., then push [Y] or [Z] to as your call sign. rWait for the reply call from the station who receive the turn OFF. break-in call. t After receive the reply call, communicate normal way. yTo cancel the break-in, push [BANK OPT ] for 1 sec., then rotate [DIAL] to turn OFF. 65
  • 12 DIGITAL MODE OPERATION I Emergency communication z Set the desired frequency then The emergency communication mode is available for Digital BANK/OPTION modes operation. In the emergency call, no call sign setting is [BANK/OPTION] for 1 sec. to enter the op- necessary. tion set mode. x Push [BANK/OPTION] or [MR/CALL] sev- q Set the desired frequency then push [BANK OPT ] for 1 eral times to select the emergency setting, sec. to enter the option set mode. then turns the emergency setting ON. w Push [BANK OPT ] or [V/MHz] several times to select the • “EMG” appears. emergency setting, then turns the emergency setting ON. c Operate the transceiver normal way. • “EMG” appears. v To cancel the emergency communication mode, push [BANK/OPTION] for 1 sec., DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE Y Z then push [Y] or [Z] to turn OFF. NAR NAR MID MID LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW eOperate the transceiver normal way. rTo cancel the emergency communication mode, push [BANK OPT ] for 1 sec., then rotate [DIAL] to turn OFF. 12 66
  • 12 DIGITAL MODE OPERATION I Digital code/Call sign squelch operation z Set the operating frequency. The digital code (CSQL) or call sign (DSQL) squelch opens TSQL x Program the digital code or call sign in setting mode. only when receiving a voice signal with the same pre-pro- grammed digital code or call sign, respectively. The digital • See p. 69, “Digital code setting” or pgs. 59, 60 “Call sign programming.” code or call sign squelch does not function while in a slow DTCS c Push [FUNC] then [SIMP 9(TSQL)] or [HIGH 4(DTCS)] data communication. to turn the digital code or call sign squelch ON. q Set the operating frequency. v When a signal with the matched digital code or w Program the digital code or call sign in setting mode. call sign is received, the squelch opens and the • See p. 69, “Digital code setting” or pgs. 59, 60 “Call sign programming.” signal can be heard. e Push [TONE T-SCAN ] several times until “ ” or “ ” ap- • When the received signal includes an unmatched digital pears in the function display. code or call sign, the squelch does not open. However, • “ ” for digital code squelch; “ ” for call sign squelch operation. the S/RF indicator shows the received signal strength. r When a signal with the matched digital code/call sign is re- Z • To open the squelch manually, push [SQLZ #(16KEY-L)] ceived, the squelch opens and the signal can be heard. several times until less than squelch level 7. • When the received signal includes an unmatched digital DIGITAL PRIO AO BUSY code/call sign, the squelch does not open. However, the S/RF MUTE NAR MID indicator shows the received signal strength. LOW LOCK T-SCAN PRIO ANM SCAN DUP • To open the squelch manually, rotate [SQL] counter clockwise. SET TONE M/CALL V/ MHz MONI LOW t Operate the transceiver in the normal way (push [PTT] to b Operate the transceiver in the normal way (push transmit; release [PTT] to receive). [PTT] to transmit; release [PTT] to receive. y To cancel the digital code/call sign squelch, push [TONE n To cancel the digital code or call sign squelch, T-SCAN ] several times until “ ” or “ ” disappears. push [FUNC] then [ENT C(T-OFF)]. NOTE: While in the digital mode operation, the monitor • “ ” or “ ” disappears. function (pushing [MONI ANM ]) works as the analog mon- ✔ While scanning in digital mode: itor for receiving an FM signal. The digital monitor function • The call sign squelch function deactivate, then after can- is activate using the Squelch control knob [SQL]. celling the scan it will activate again. • Scan stops near channel in a 5 kHz tuning steps, and then no sound comes out. 67
  • 12 DIGITAL MODE OPERATION I Slow data communication t Start up the slow data communication application. In addition to the digital voice communication, a slow data ySet the application as follows. communication is available (Refer p. 5 about the transceiver- PC connection details). • Port : The same COM port number as IC-2200H’s • Baud rate : 4800 bps or 9600 bps (same as step r) q Set the desired frequency. • Data : 8 bit wSet another settings, such as repeater call, digital code • Parity : None squelch, transmit output power. • Stop : 1 bit e Push [BANK OPT ] for 1 sec. then push [BANK OPT ] or • Flow control : Xon/Xoff [V/MHz] several times to select the automatic data trans- uTransceiver automatically transmits or receive the data mission setting. (see p. 69) when you sending data to transceiver. Or push and hold • “ATX” appears. [PTT] to transmit, release to receive the data manually. • Skip this setting, if you want to transmit manually. • Refer to the instruction of the application that how to send or re- ceive data. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR MID MID z Set the desired frequency. LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW BANK/OPTION x Set another settings, such as repeater, dig- 12 r Push [BANK OPT ] once to select the data communica- ital code squelch, transmit output power. c Push [BANK/OPTION] for 1 sec. then tion speed setting. (see p. 70) • “SPD” appears. push [BANK/OPTION] or [MR/CALL] to • Select suitable data speed for your PC or application. select the automatic transmission setting. • “ATX” appears. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY • Skip this setting, if you want to transmit manually. MUTE MUTE NAR NAR MID MID v Push [BANK/OPTION] to select the data LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW communication speed. • “SPD” appears. • Select suitable data speed for your PC or ap- plication. b Start up the slow data communication ap- plication, then follow step y at above. 68
  • 12 DIGITAL MODE OPERATION I Other setting items qPush [BANK OPT ] for 1 sec. then push [BANK OPT ] or D Digital Code [V/MHz] several times to select the desired item. Sets the desired digital code for digital code squelch opera- w Rotate [DIAL] to select the desired value or condition. tion. Total of 100 codes (00–99) are available. (default: 00) z Push [BANK/OPTION] for 1 sec. then DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR BANK/OPTION push [BANK/OPTION] or [MR/CALL] sev- MID MID LOW LOW eral times to select the desired item. LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW x Push [Y] or [Z] to select the desired value Y Z or condition. D Auto data Transmission During slow data operation, auto data transmission function D Auto Reply is available. This function transmits when data are input from During Digital mode operation, auto reply function is avail- PC via the [DATA] jack. (default: OFF) able. This function replys to an individual station call even you After the manual transmission (pushing [PTT]), the Auto are away from the transceiver. (default: OFF) Transmission setting is return to OFF automatically. After the manual transmission (pushing [PTT]), the Auto Reply setting is return to OFF automatically. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR MID MID LOW LOW DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP MUTE MUTE SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW NAR NAR MID MID LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW 69
  • 12 DIGITAL MODE OPERATION D Data Speed D Auto RxCall Write Select the communication speed between the transceiver and When an individual station call is received, the calling station PC from 4800 baud or 9600 baud. call sign can be stored automatically. The stored call sign can (default: 9600) be re-called when selecting a station call sign. (default: OFF) DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MID MID MUTE MUTE LOW LOW NAR NAR LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP MID MID SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW D Standby Beep D Auto Rx RepeaterCall Write Turns the beep emission capability when the communicating station finishes transmitting or the receive signal disappears. When an individual station call via the repeater is received, (default: OFF) the repeater call sign can be stored automatically. The stored repeater’s call sign can be re-called when selecting a re- DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY peater call sign. MUTE MUTE NAR NAR MID MID (default: OFF) 12 LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR MID MID LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW 70
  • 12 DIGITAL MODE OPERATION D Message Transmission D TX message programming Select the Message transmission function ON and OFF. A TX message channel C1 must be programmed, if you want When ON is selected, transceiver transmits a text message to use the GPS message. The GPS message is transmitted (pre-programmed). from channel C1 only. (default: OFF) q Push [MONI] (or [SET]) to edit for 1 sec. then rotate After the manual transmission (pushing [PTT]), the Message [DIAL] to select the message channel. Transmission setting is return to OFF automatically. • One of either “C1” to “C6” flashes. w Push [MONI] (or [SET]) to set into message programming DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE condition. NAR NAR MID MID LOW LOW • The 1st digit blinks and channel indication stops blinking. LOCK PRIO ANM T-SCAN SCAN LOCK ANM T-SCAN PRIO SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW e Rotate [DIAL] to set the desired character. r Push [MONI] (or [SET]) to select 2nd digit, then rotate [DIAL] to set the desired character. • 2nd digit blinks (1st digit stop blinking). D TX message • Repeat this step for programming. TX messages are available up to 6 channels and each chan- t Push [V/MHz] to set the message. nel can be programmed up to 20 characters message. Avail- y Repeat steps w to t to set another message channels. able characters are 0 to 9, A to Z (capital letters only), some u Push any key other than indicated function keys to exit the symbols and space. (shown at right table) option set mode. DIGITAL PRIO AO BUSY (space) (!) (#) ($) (%) (&) (’) (( ) ( )) (✱) MUTE NAR MID LOW (+) (,) (–) (.) (/) (0) (1) (2) (3) LOCK T-SCAN PRIO ANM SCAN DUP (4) (5) SET TONE M/CALL V/ MHz MONI LOW (>) (?) (@) (:) (;) (<) (=) (6) (7) (8) (9) (E) (F) (G) (H) (I) (J) (K) (A) (B) (C) (D) (L) (M) (N) (O) (P) (Q) (R) (S) (T) (U) (V) (W) (X) (Y) (Z) ([) () (]) (^) 71
  • 12 DIGITAL MODE OPERATION I GPS operation rPush [BANK OPT ] twice to select the position indication. The IC-2200H can indicate the current position (Latitude and Lon- gitude) when a GPS receiver (compatible with an RS-232C out- DIGITAL PRIO AO BUSY MUTE put/NMEA format/4800 bps) is connected to [DATA] jack. And NAR MID also can transmit the position data and message to other stations. LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW t Push [MONI] (or [SET]) to enter the position indication. D Position indication • Latitude and longitude date appear in order as below. q While connecting a GPS receiver, push [BANK OPT ] for DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY 1 sec. to enter the option set mode. MUTE MUTE NAR NAR w Push [BANK OPT ] or [V/MHz] several times to select the MID MID LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO ANM SCAN DUP GPS setting. SET TONE M/CALL V/ MHz MONI LOW SET TONE M/CALL V/ MHz MONI LOW Minutes Seconds North or South Degrees • “GPS” appears. () Push LOCK SET DIGITAL PRIO AO BUSY MUTE () Push NAR MONI MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE 12 NAR NAR e Rotate [DIAL] to set the suitable sentence formatter for the MID MID LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP connecting GPS receiver. LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW SET TONE M/CALL V/ MHz MONI LOW • For your position indication is necessary to select “GGA” or “RMC.” Minutes Seconds East or West Degrees DIGITAL PRIO AO BUSY yAfter checking the current position, push any key other MUTE NAR MID than indicated function keys to return to normal operating LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW mode. • Sentence formatters IMPORTANT: When set the sentence formatter at step e 1 GLL 6 GLL, GGA 11 GGA, GSA 16 GLL, GGA, RMC 21 GLL, GSA, VTG for connecting GPS receiver, and already programmed your 2 GGA 7 GLL, RMC 12 GGA, VTG 17 GLL, GGA, GSA 22 GGA, RMC, GSA call sign, GPS automatic transmission is activate every 3 3 RMC 8 GLL, GSA 13 RMC, GSA 18 GLL, GGA, VTG 23 GGA, RMC, VTG minutes. The automatic transmission can be changed inter- 4 GSA 9 GLL, VTG 14 RMC, VTG 19 GLL, RMC, GSA 24 GGA, GSA, VTG 5 VTG 10 GGA, RMC 15 GSA, VTG 20 GLL, RMC, VTG 25 RMC, GSA, VTG val time or deactivated, if desired. (see next page) 72
  • 12 DIGITAL MODE OPERATION D GPS Automatic transmission IMPORTANT: GPS Automatic transmission transmits at every setting interval even while receiving an another sta- q While connecting a GPS receiver, push [BANK OPT ] for tions communication. To prevent interfere the another sta- 1 sec. to enter the option set mode. tions, set the GPS transmission together with the Repeater w Push [BANK OPT ] or [V/MHz] several times to select the lockout item “RLO” (set to “BU” busy lockout) in initial set GPS automatic transmission. mode. (p. 84) • “GTX” appears. DIGITAL PRIO AO BUSY MUTE D Receiving a GPS transmission NAR MID LOW q Push [BANK OPT ] for 1 sec. to enter the option set LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW mode. e Rotate [DIAL] to set the interval time for the GPS auto- w Push [BANK OPT ] or [V/MHz] several times to select the matic transmission. received position. • Interval time is selectable from 0.5 (30 sec.), 1, 3, 5, 10, 30 min. • “RX POS” appears. DIGITAL PRIO AO BUSY MUTE DIGITAL PRIO AO BUSY NAR MUTE MID NAR LOW MID LOCK T-SCAN PRIO ANM SCAN DUP LOW SET TONE M/CALL V/ MHz MONI LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW rPush [SET] or [MONI] several times to edit transmit mes- e Push [MONI] (or [MONI]) to enter the position indication. sage, if desired. (see page 71) • Latitude data and longitude date appear alternately. • When TX message channel “C1” is programmed, GPS transmis- rPush [BANK OPT ] twice to select the received GPS mes- sion automatically transmits TX message “C1.” sage. tPush any key other than indicated function keys to exit op- tPush [MONI] (or [SET]) to enter the message. tion set mode. • Received message is indicated, push [MONI] or [SET] to move the cursor to left or right, respectively. yAfter checking a received position and message, push any key other than indicated function keys to return to normal operating mode. 73
  • 13 OTHER FUNCTIONS I Set mode • Set mode operation z Push [SET B(D-OFF)] to enter set mode. q Push [SET LOCK ] to enter the set mode. SET x Push [SET B(D-OFF)] or [ENT C(T-OFF)] to select w Push [SET] or [MONI] to select the desired item. B the desired item. e Rotate [DIAL] to select the condition or value. c Push [Y] or [Z] to select the condition or value. Y Z r Push any key other than [SET] or [MONI] to exit set mode. v Push [CLR A(MW)] to exit set mode. • Set mode items • Display dimmer • Repeater tone frequency • DTCS code • Tone squelch • Display color • DTCS polarity frequency • Weather alert* • Offset frequency ( ) (front panel); or LOCK : Push (microphone) SET 12 ( ) (front panel); or • Reverse mode • AM/FM mode select* ANM : Push (microphone) MONI 13 *Available for USA version only. † Appears when accessing set mode from VFO mode only. ‡ • Wide/Nar. setting* • Tuning step Appears when accessing set mode from memory mode only. • Scan resume timer • Channel skip setting‡ • Bank link function‡ • Bank setting‡ • Transmit permission 74
  • 13 OTHER FUNCTIONS D Display dimmer D Tone squelch tone Adjust to suit lighting conditions. Sets subaudible tone frequency (both encoder and decoder) The levels 1 (dark) to 4 (bright: default) are available. for tone squelch operation. Total of 50 tone frequencies (67.0–254.1 Hz) are available. (default: 88.5 Hz) DIGITAL PRIO AO BUSY MUTE NAR DIGITAL PRIO AO BUSY MID MUTE LOW NAR LOCK T-SCAN PRIO ANM SCAN DUP MID SET TONE M/CALL V/ MHz MONI LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW • Available subaudible tone frequencies D Display color 67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1 69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6 The display color can be set to amber (default) or green. 71.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.8 74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3 DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY 77.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1 MUTE MUTE NAR NAR MID MID LOW LOW D DTCS code and polarity LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW Sets DTCS code (both encoder and decoder) for DTCS Amber setting (default) Green setting squelch operation. Total of 104 codes are available. (default: 023) D Repeater tone DIGITAL PRIO AO BUSY MUTE NAR MID Sets subaudible tone frequency (encoder only) for repeater LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW operation. Total of 50 tone frequencies (67.0–254.1 Hz) are available. (default: 88.5 Hz) D DTCS polarity DIGITAL PRIO AO BUSY Sets DTCS polarity for transmission and reception from “NN,” MUTE NAR “NR,” “RN,” “RR.” (default: NN) MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW 75
  • 13 OTHER FUNCTIONS D Offset frequency D Scan resume timer Sets the duplex offset frequency within 0 to 20 MHz range. Selects scan resume timer from SCT-15 (default), SCT-10, During duplex (repeater) operation, transmit frequency (or re- SCT-5 and SCP-2. ceive when reverse function is set to ON) shifts the set fre- • SCT-15/10/5 : Scan pauses for 15/10/5 sec., then re- quency. (default value may differ depending on versions) sumes. • SCP-2 : Pause on a signal until signal disap- DIGITAL PRIO AO BUSY MUTE pears, then resumes 2 sec. after the sig- NAR MID nal disappears. LOW LOCK PRIO ANM T-SCAN SCAN DUP SET TONE M/CALL V/ MHz MONI LOW DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR MID MID LOW LOW LOCK T-SCAN PRIO ANM SCAN LOCK DUP ANM DUP T-SCAN PRIO SCAN SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW D Reverse mode Sets the reverse function ON and OFF (default). DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY D Transmit permission MUTE MUTE NAR NAR MID MID LOW LOW Turns transmission permission ON and OFF. This function LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM SCAN DUP ANM DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW can be set for each memory, call channel and VFO, indepen- Reverse function OFF (default) Reverse function ON dently. 13 DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR MID MID D Tuning step LOW LOW LOCK PRIO ANM SCAN LOCK DUP T-SCAN ANM DUP T-SCAN PRIO SCAN SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW Selects tuning step from 5 (default), 10, 12.5, 15, 20, 25, 30 Transmission is permitted. Transmission is inhibited. and 50 kHz for [DIAL] or [Y]/[Z] operation. (default) DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET TONE M/CALL V/ MHz MONI LOW 76
  • 13 OTHER FUNCTIONS D Channel skip setting D Memory bank link function Sets channel skip setting from ON and OFF for memory skip Sets the memory bank link function ON and OFF (default). scan operation. The link function provides continuous banks scan, that scans This item appears when set mode is accessed from memory all contents in the selected banks during bank scan. mode only. This item appears when set mode is accessed from memory mode only. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MID MID MUTE MUTE LOW LOW NAR NAR LOCK ANM T-SCAN PRIO SCAN LOCK DUP ANM DUP T-SCAN PRIO SCAN MID MID SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW LOW LOW LOCK PRIO PRIO ANM T-SCAN SCAN LOCK ANM T-SCAN SCAN DUP DUP Scans the memory channel. Does not scan the memory SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW (does not skip; default) channel (skips). D Memory bank setting • Bank link setting Sets the desired memory bank (A to J and OFF) to assign the q Rotate [DIAL] to select the memory bank link function ON. regular memory channels. w Push [SET] or [MONI] to select the desired bank to be This item appears when set mode is accessed from memory linked. mode only. • BLA: Bank A, BLB: Bank B, BLC: Bank C, BLD: Bank D, BLE: Bank E, BLF: Bank F, BLG: Bank G, BLH: Bank H, DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY BLI: Bank I, BLJ: Bank J MUTE MUTE NAR NAR MID MID LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW MUTE MUTE NAR NAR MID MID LOW LOW LOCK ANM T-SCAN PRIO SCAN LOCK PRIO SCAN DUP ANM DUP T-SCAN SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW e Rotate [DIAL] to select “ON” to linking the bank. r Repeat steps w and e to set the link condition. 77
  • 13 OTHER FUNCTIONS D Wide/Narrow setting D Weather alert function U.S.A. versions only Sets both the transmission and reception passband width Turns weather alert function ON and OFF. from wide and narrow. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY When narrow is set, the transmission deviation and reception MUTE MUTE NAR NAR MID MID passband width become half of the wide setting (approx.). LOW LOW LOCK PRIO PRIO ANM T-SCAN SCAN LOCK ANM SCAN DUP DUP T-SCAN This setting can be set for each memory, call and VFO inde- SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW Weather alert OFF (default) Weather alert ON pendently. NOTE: This item MUST be set “W” (WIDE) when operating the digital mode. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR MID MID LOW LOW LOCK T-SCAN PRIO ANM SCAN LOCK PRIO DUP ANM SCAN DUP T-SCAN SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW Wide setting (default) Narrow setting D AM/FM mode selection Sets the operating mode for receiving from AM or FM mode (default). 13 NOTE: This item MUST be set “FM” when operating the digital mode. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR MID MID LOW LOW LOCK PRIO SCAN LOCK PRIO ANM SCAN DUP T-SCAN ANM DUP T-SCAN SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW FM mode selection (default) AM mode selection 78
  • 13 OTHER FUNCTIONS I Initial set mode POWER ON AT D Entering initial set mode The initial set mode is accessed at power ON and al- q While pushing [SET LOCK ], push [PWR] for 1 sec. to lows you to set seldom-changed settings. In this way, enter initial set mode. you can “customize” transceiver operations to suit your w Push [SET] or [MONI] to select the desired item. preference and operating style. e Rotate [DIAL] to select the condition or value. r Push [PWR] to exit initial set mode. • Initial set mode items • Auto power OFF • Auto repeater* • Time-out timer DIGITAL DIGITAL DIGITAL MUTE MUTE MUTE NAR NAR NAR MID MID MID • Key-touch beep LOW LOW LOW LOCK ANM DUP T-SCAN LOCK ANM DUP T-SCAN LOCK ANM DUP T-SCAN SET TONE SET MONI LOW TONE MONI LOW SET TONE MONI LOW DIGITAL MUTE NAR MID LOW • Repeater lockout LOCK ANM DUP T-SCAN SET TONE MONI LOW DIGITAL MUTE NAR • ALC setting MID LOW ( ) (front panel); or LOCK ANM DUP T-SCAN LOCK : Push (microphone) SET TONE MONI LOW DIGITAL SET MUTE NAR ( ) (front panel); or MID ANM : Push (microphone) LOW MONI LOCK ANM DUP T-SCAN • Squelch delay SET TONE MONI LOW DIGITAL *Available in USA version only. MUTE NAR • Squelch attenuator MID LOW LOCK ANM DUP T-SCAN SET TONE MONI LOW DIGITAL MUTE NAR MID • S-meter squelch • Display type • DTMF speed LOW LOCK ANM DUP T-SCAN SET TONE MONI LOW DIGITAL DIGITAL DIGITAL MUTE MUTE MUTE NAR NAR NAR MID MID MID LOW LOW LOW LOCK ANM DUP T-SCAN LOCK ANM DUP T-SCAN LOCK ANM DUP T-SCAN SET TONE MONI LOW SET TONE MONI LOW SET TONE MONI LOW 79
  • 13 OTHER FUNCTIONS D Key-touch beep D Auto repeater U.S.A. version only The key-touch beep can be turned OFF for silent operation. The auto repeater function automatically turns ON or OFF the (default: ON) duplex operation with a specified shift direction and tone en- coder, when the operating frequency falls within or outside of DIGITAL PRIO AO BUSY 145.200–145.495 MHz, 146.610–146.995 MHz and MUTE NAR MID 147.000–147.395 MHz range. The offset and repeater tone LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW frequencies are not changed by the auto repeater function, reset these frequencies, if necessary. • OF : The auto repeater function is turned OFF. D Time-out timer • R1 : Activates for duplex only. (default) • R2 : Activates for duplex and tone. To prevent accidental prolonged transmission, etc., the trans- ceiver has a time-out timer. This function cuts a transmission DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE OFF after 1–30 min. of continuous transmission. This timer NAR NAR MID MID LOW LOW can be cancelled. LOCK PRIO PRIO ANM SCAN LOCK SCAN DUP T-SCAN ANM DUP T-SCAN SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW • TOT-OF : The time-out timer is turned OFF. (default) • TOT-1–30 : The transmission is cut OFF after the set period elapses. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY 13 MUTE MUTE NAR NAR MID MID LOW LOW LOCK PRIO ANM T-SCAN SCAN LOCK T-SCAN PRIO ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW 80
  • 13 OTHER FUNCTIONS D Auto power OFF D Squelch delay The transceiver can be set to automatically turn OFF after a Selects squelch delay from short and long to prevent re- specified period with a beep when no key operations are per- peated opening and closing of the squelch during reception formed. of the same signal. •S : Short squelch delay (default) 30 min., 1 hour, 2 hours and OFF (default) can be specified. •L : Long squelch delay The specified period is retained even when the transceiver is DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY turned OFF by the auto power OFF function. To cancel the MUTE MUTE NAR NAR function, select “OF” in this set mode. MID MID LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY Short squelch delay setting Long squelch delay setting MUTE MUTE NAR NAR MID MID LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW D S-meter squelch Selects S-meter squelch threshold level from OFF and D Repeater lockout S1–S7. Selects lockout type from repeater, busy and OFF. This setting allows you to set a minimum signal level needs to • OF : No lockout is activated (default) open the squelch. • RP : The repeater lockout is turned ON • BU : The busy lockout is turned ON DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR MID MID LOW LOW DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP MUTE MUTE SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW NAR NAR MID MID LOW LOW S-meter squelch OFF (default) S2 level (2 indicator level) LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW Busy lock-out setting Repeater lock-out setting 81
  • 13 OTHER FUNCTIONS D DTMF speed D Squelch attenuator The rate at which DTMF memories send individual DTMF Turns the squelch attenuator function ON and OFF. characters can be set to accommodate operating needs. • ON : The squelch attenuator activates when [SQL] •1 : 100 msec. interval; 5.0 cps speed (default) control is set between 12 o’clock and fully •2 : 200 msec. interval; 2.5 cps speed clockwise position. (default) •3 : 300 msec. interval; 1.6 cps speed • OF : The squelch attenuator does not function. •5 : 500 msec. interval; 1.0 cps speed DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR DIGITAL PRIO AO BUSY MID MID MUTE LOW LOW NAR LOCK ANM T-SCAN PRIO SCAN LOCK PRIO ANM T-SCAN SCAN DUP DUP MID SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW D ALC function D Display type Sets the ALC (Automatic Level Control) function ON and OFF Selects LCD indication type from frequency, channel number (default). and channel names. The ALC function reduces the microphone gain automatically • FR : Shows frequency (default) when the transmission audio is distorted. • CH : Shows channel number* DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY 13 • NM : Shows channel names MUTE MUTE NAR NAR MID MID *Programmed memory channels only can be selected. LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY ALC function OFF (default) ALC function ON MUTE MUTE NAR NAR MID MID LOW LOW LOCK T-SCAN PRIO SCAN LOCK T-SCAN PRIO ANM ANM SCAN DUP DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW Frequency indication setting Memory channel name indication setting 82
  • 13 OTHER FUNCTIONS I Weather channel operation U.S.A. versions only D Weather channel selection q Select the desired weather channel. w Turn the weather alert function ON in set mode. q Push [M/CALL PRIO ] sev- ➥ Push [SET LOCK ] to enter set mode. eral times to select weather ➥ Push [SET LOCK ] or [S.MW MW ] to select the channel group. weather alert item, then rotate [DIAL] to set ON. w Rotate [DIAL] to select the ➥ Push [TONE T-SCAN ] to exit set mode. desired weather channel. DIGITAL PRIO AO BUSY e Sets the desired stand-by condition. MUTE e Push [M/CALL PRIO ] to NAR MID • Selects VFO, memory or call channel. LOW select memory mode, or LOCK ANM T-SCAN PRIO SCAN DUP • Scan or priority watch operation can also be selected. SET TONE M/CALL V/ MHz MONI LOW push [V/MHz SCAN ] to se- r When the alert is detected, a beep sounds and the follow- lect VFO mode. ing indication will be displayed. DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR D Weather alert function MID MID LOW LOW LOCK ANM T-SCAN PRIO SCAN LOCK T-SCAN PRIO SCAN DUP ANM DUP SET SET TONE M/CALL TONE M/CALL V/ MHz V/ MHz MONI LOW MONI LOW NOAA broadcast stations transmit weather alert tones before Shows above indications alternately. important weather announcements. When the weather alert t Turn the weather alert function OFF in set mode. function is turned ON, the selected weather channel is moni- tored each 5 sec. for the announcement. When the alert sig- nal is detected, the “AL.T” and the WX channel are displayed NOTE: While receiving a signal (on a frequency other than alternately and sounds a beep tone until the transceiver is op- the weather alert ON frequency), the receiving signal or erated. The previously selected (used) weather channel is audio will be interrupted momentarily every 5 sec. (approx.) checked periodically during standby or while scanning. in case the alert function is turned ON. This symptom is caused by the WX alert function. To cancel these symp- toms, set the weather alert item OFF in set mode. 83
  • 13 OTHER FUNCTIONS I Microphone keys D [UP]/[DN] keys on a microphones The supplied HM-133V’s (optional for some versions) [F-1] and [F-2] keys memorize the transceiver conditions. (other than HM-133V) POWER ON AT The [UP]/[DN] keys of the standard or an optional micro- The following functions are assigned to the [UP]/[DN] keys phone (other than the HM-133V) can be assigned functions on the other microphones (HM-118N/TAN, etc.) when first ap- like the function keys on the transceiver’s front panel. plying power. D [F-1]/[F-2] keys on HM-133V [UP] : channel up; push and hold to start scan, push again The following conditions can be memorized into [F-1] and to stop scan. [F-2] keys, independently. [DN] : channel down; push and hold to start scan, push again to stop scan. • Operating frequency • Repeater setting (offset direction and frequency, tone ➥ Assigning a function ON/OFF and frequency) q Turn the power OFF. • Tone/DTCS squelch (ON/OFF, frequency/code and polarity) w While pushing the desired key on the transceiver and one • Transmit output power selection of either [UP]/[DN] keys on the microphone, turn the • Set mode settings power ON. • Initial set mode settings (except display type item) • The function is programmed into the key. 13 ➥ Programming the condition ➥ Clearing an assignment [F-1]/[F-2] Set the desired contents of each condition, q Turn the power OFF. then push [F-1]/[F-2] for 1 sec. w While pushing the desired [UP] or [DN] key on the micro- • 3 beeps sound. phone, turn the power ON. ➥ Re-calling the condition Push [F-1]/[F-2] momentarily. 84
  • 13 OTHER FUNCTIONS I Partial reset I All reset POWER ON POWER ON AT AT If you want to initialize the operating conditions (VFO fre- The function display may occasionally display erroneous in- quency, VFO settings, set mode contents) without clearing formation (e.g. when first applying power). This may be the memory contents, a partial resetting function is available caused externally by static electricity or by other factors. for the transceiver. If this problem occurs, turn power OFF. After waiting a few ➥ Turn power OFF, if transceiver is powered ON. seconds, turn power ON again. If the problem persists, per- ➥ While pushing [V/MHz SCAN ], turn the power ON to par- form the following procedure. • Partial resetting is also available. See left for details. tially reset the transceiver. IMPORTANT!: DIGITAL PRIO AO BUSY MUTE Resetting the transceiver CLEARS all memory information NAR MID LOW and initializes all values in the transceiver. LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW [PWR] ➥ While pushing [SET LOCK ] and [S.MW MW ], turn the power ON to reset the CPU. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW [S.MW MW] [PWR] 85
  • 13 OTHER FUNCTIONS I Data cloning POWER ON AT Cloning allows you to quickly and easily transfer the pro- w While pushing [M/CALL grammed contents from one transceiver to another; or , data PRIO ], turn power ON to from a personal computer to a transceiver using the optional enter cloning mode (mas- CS-2200H CLONING SOFTWARE. ter transceiver only— ( ), PRIO While pushing M/ CALL power on only for sub- D Cloning between transceivers turn power ON. transceiver). q Connect the OPC-474 cloning cable to the [SP] jack of the DIGITAL PRIO AO BUSY • “CLONE” appears and the MUTE NAR master and sub-transceivers. transceivers enter the clone MID LOW • The master transceiver is used to send data to the sub-trans- LOCK PRIO ANM T-SCAN SCAN DUP standby condition. SET TONE M/CALL V/ MHz MONI LOW ceiver. e Push [S.MW MW ] on the master transceiver. • “CL OUT” appears in the master transceiver’s display S.MW MW and the S/RF indicator shows Push to start cloning 13 that data is being transferred (master transceiver). to the sub-transceiver. DIGITAL PRIO AO BUSY • “CL IN” appears automati- MUTE NAR cally in the sub-transceiver’s MID LOW LOCK T-SCAN PRIO ANM SCAN DUP display and the S/RF indica- SET TONE M/CALL V/ MHz MONI LOW tor shows that data is being received from the master transceiver. r When cloning is finished, turn power OFF, then ON to exit cloning mode. 86
  • 13 OTHER FUNCTIONS D Cloning using a personal computer D Cloning error Data can be cloned to and from a personal computer (Mi- NOTE: DO NOT push any key on the sub-transceiver dur- crosoft® Windows® 98/98SE/2000/Me/XP) using the optional ing cloning. This will cause a cloning error. CS-2200H CLONING SOFTWARE and the optional OPC-478 When the display at left ap- (RS-232C type) or OPC-478U (USB type) CLONING CABLE. DIGITAL PRIO AO BUSY MUTE pears, a cloning error has oc- NAR Consult the CS-2200H CLONING SOFTWARE HELP file for de- MID curred. LOW LOCK ANM T-SCAN PRIO SCAN DUP tails. SET TONE M/CALL V/ MHz MONI LOW In such a case, both trans- ceivers automatically return to the clone standby condition and cloning must be repeated. Personal computer to RS-232C port OPC-478 or OPC-478U to USB port Microsoft and Windows are registered trademarks of Microsoft Corporation in the U.S.A. and other countries. 87
  • 14 SPECIFICATIONS GENERAL • Frequency coverage : (unit: MHz) • Max. frequency deviation : ±5.0 kHz [Wide]/±2.5 kHz [Narrow]‡ USA, Asia, Australia Tx: 144–148/Rx: 118–174* • Spurious emissions : Less than –60 dBc : 8-pin modular (600 Ω) Europe Tx: 144–146/Rx: 118–174* • Microphone connector Europe-1, Taiwan, Korea Tx/Rx: 144–146 *Guaranteed: 144–148 MHz range only. RECEIVER • Type of emission : FM, AM (Receive only) • Receive system : Double-conversion superheterodyne • Number of memory channels : 207 (incl. 6 scan edges and 1 call) • Intermediate frequencies : 1st: 21.7 MHz, 2nd: 450 kHz • Frequency resolution : 5, 10, 12.5, 15, 20, 25, 30, 50 kHz • Sensitivity (at 12 dB SINAD) : 0.14 µV typical • Operating temperature range : –10°C to +60°C; +14˚F to +140˚F • Squelch sensitivity (threshold): 0.1 µV typical • Frequency stability : ±10 ppm (–10°C to +60°C) • Selectivity : • Power supply requirement : 13.8 V DC ±15% [Wide] More than ±6 kHz/6 dB • Current drain (at 13.8 V DC: approx.): Less than ±14 kHz/60 dB Transmit at 65 W 15 A [Narrow]‡ More than ±3 kHz/6 dB Receive standby 0.8 A Less than ±9 kHz/55 dB max. audio 1.0 A • Spurious and image rejection : 75 dB typical : SO-239 (50 Ω) • Antenna connector • AF output power (at 13.8 V DC) : More than 2.4 W at 10% distortion with • Dimensions (proj. not included) : 140(W) × 40(H) × 146(D) mm an 8 Ω load 51⁄2(W)×19⁄16(H)×53⁄4(D) in : 3-conductor 3.5 (d) mm (1⁄8″)/8 Ω • Ext. speaker connector • Weight (approx.) : 1.25 kg; 2 lb 12 oz : 3-conductor 2.5 (d) mm (1⁄8″) • Ext. Data connector 13 TRANSMITTER Some version only ‡ 14 • Modulation system : Variable reactance frequency mod. • Output power : Power output Power (*approx., †Korea version) Selection Taiwan High 65 W (50 W†) 24 W Middle 25 W* 10 W* Mid. low 10 W* N/A Low 5 W* 5 W* All stated specifications are subject to change without notice or obligation. 88
  • 15 MAINTENANCE I Troubleshooting If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. PROBLEM POSSIBLE CAUSE SOLUTION REF. No power comes on. • Power connector has a poor contact. • Check the connector pins. — • Polarity of the power connection is reversed. • Re-connect the power cable observing the proper pgs. II, polarity. Replace the fuse if damaged. 90 • Blown fuse. • Check the cause, then replace the fuse. p. 90 No sound comes from the • Volume is too low. • Rotate [VOL] clockwise. p. 13 speaker. • The audio mute function is activated. • Push any switch or key to deactivate it. p. 14 • Squelch is set too tight. • Set the squelch level to the threshold. p. 13 • A selective call or squelch function is activated • Turn the appropriate function OFF. pgs. 48, such as pocket beep or tone squelch. 49, 50 Sensitivity is low and only • Antenna feedline or the antenna connector solder • Check, and if necessary, replace the feedline or sol- p. III strong signals are audible. has a poor contact or is short circuited. der the antenna connector again. • Squelch attenuator function is activated. • Set [SQL] between 10–12 o’clock position. p. 14 No contact possible with • The other station is using tone squelch. • Turn the tone squelch function ON. p. 50 another station. • The transceiver is set to duplex. • Set to simplex. p. 17 Repeater cannot be ac- • Wrong offset frequency is programmed. • Correct the offset frequency. p. 21 cessed. • Wrong subaudible tone frequency is programmed. • Correct the subaudible tone frequency. p. 19 Frequency cannot be set. • The frequency lock function is activated. • Turn the function OFF. p. 12 • Priority watch is paused on the watching frequency. • Push [M/CALL PRIO ] to cancel the watch. p. 44 Frequency cannot be set • The frequency lock function is activated. • Push [SET LOCK ] for 1 sec. to deactivate the fre- p. 12 via the microphone. quency lock function. • The microphone keypad lock function is activated. • Push [FUNC] then [#(16KEY-L)] to deactivate the p. 12 • Priority watch is paused on the watching fre- microphone keypad lock function. quency. • Push [M/CALL PRIO ] to cancel the watch. p. 44 89
  • 15 MAINTENANCE PROBLEM POSSIBLE CAUSE SOLUTION REF. Some memory channels • The input channel number has not yet been pro- • Rotate [DIAL] to check whether the channel has — cannot be selected via the grammed. been programmed or not. microphone keypad. Scan does not operate. • The squelch is open. • Set the squelch to the threshold point. p. 13 • Only 1 memory channel is programmed or other • Program other memory channels or cancel the pgs. 25, channels are set as skip channels. memory skip function in the desired channels. 26, 41 • Priority watch is activated. • Cancel the watch. p. 44 Transmission is automati- • Time-out timer is activated. • Set the timer to OFF. p. 80 cally cut off. Transmission continues • One-touch PTT function is activated. • Turn the function OFF. p. 16 even when the PTT is re- leased. The function display shows • The CPU is malfunctioning. • Reset the CPU. p. 85 erroneous information. I Fuse replacement If the fuse blows or the transceiver stops functioning, find the source of the problem if possible, and replace the damaged 20 A 15 fuse with a new, rated one (FGB 20 A) as shown at right. fuse 90
  • 15 MAINTENANCE I Optional unit installation q Remove [DIAL] and unscrew the 2 allen-socket bolts from t Install the unit as illustrated below. Insert tightly to avoid the front panel using with an allen wrench (2.5 mm; 1⁄10″) bad contact. Flat cable Allen-socket bolts w Detach the front panel from the main unit. Insulation sheet y Return the front panel and the allen-socket bolts to their original position. NOTE: When attaching the front panel to the main unit, make sure the flat cable are running in the groove to prevent catching between front panel and main unit. e Attach the insulation sheet (supplied as accessory) to IC on the Front unit. r Remove the protective paper attached to the bottom of the optional unit to expose the adhesive strip. 91
  • 16 CE DECLARATION OF CONFORMITY We Icom Inc. Japan 1-1-32, Kamiminami, Hirano-ku Osaka 547-0003, Japan Declare on our sole responsibility that this equipment complies with the Düsseldorf 8th Dec. 2003 essential requirements of the Radio and Telecommunications Terminal Place and date of issue Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suite measurements have been performed. Icom (Europe) GmbH Kind of equipment: FM TRANSCEIVER Himmelgeister straße 100 D-40225 Düsseldorf i2200H Type-designation: Authorized representative name T. Maebayashi General Manager Version (where applicable): This compliance is based on conformity with the following harmonised standards, specifications or documents: i) EN 301 489-1 v 1.3.1 (2001-09) 15 ii) EN 301 489-15 v 1.1.1 (2000-09) 16 iii) EN 301 783 v 1.1.1 (2000-09) Signature iv) EN 60950 (1992-08) + A11:1997 92
  • 17 MODE ARRANGEMENT VFO mode (p. 9) LOCK SET DIGITAL PRIO AO BUSY MUTE NAR MID LOW T-SCAN LOCK PRIO T-SCAN SCAN ANM DUP TONE SET TONE M/CALL V/MHz LOW MONI When the DTMF memory encoder is SCAN SCAN SCAN activated. PRIO V/MHz V/ MHz BANK OPT V/MHz M/CALL DTMF MEMORY DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE NAR NAR DIGITAL PRIO AO BUSY MID MID MUTE LOW LOW NAR PRIO LOCK PRIO ANM T-SCAN SCAN DUP LOCK PRIO ANM T-SCAN SCAN DUP MID SET TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz MONI LOW M/CALL LOW LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW MEMORY MODE (p. 24) CALL CHANNEL (p. 35) See p. 45 for details. DIGITAL PRIO AO BUSY MUTE ANM NAR MID MONI LOW CLONE MODE LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW for 1 sec. WEATHER CHANNEL (p. 83)*2 DIGITAL PRIO AO BUSY MUTE BANK OPT NAR MID LOW LOCK T-SCAN PRIO ANM SCAN DUP ANM SET TONE M/CALL V/ MHz MONI LOW MONI DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE MUTE See p. 86 for details. NAR NAR MID MID for 1 sec. LOW LOW LOCK T-SCAN PRIO ANM SCAN DUP LOCK T-SCAN PRIO ANM SCAN DUP SET TONE M/CALL V/ MHz MONI LOW SET TONE M/CALL V/ MHz MONI LOW *1Appears when accessing from memory mode only. CHANNEL NAME BANK CHANNEL (p. 32) *2Available for USA versions only. INDICATION (p. 29) *3Appears in some version only. 93
  • 17 MODE ARRANGEMENT SET MODE INITIAL SET MODE ( LOCK ). DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY Turn power ON while pushing SET DIGITAL Display dimmer (p. 75) Scan resume timer (p. 76) DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL Beep tone on/off (p. 80) Transmit permission (p. 76) Display color (p. 75) S-meter squlch (p. 81) DIGITAL DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL Time-out timer (p. 80) Skip setting*1 (p. 77) Repeater tone (p. 75) DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DTMF speed (p. 82) DIGITAL Memory bank selection*1 (p. 77) DIGITAL Tone squelch tone (p. 75) Auto repeater*2 (p. 80) DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY SET Display type (p. 82) SET MONI MONI Bank link function*1 (p. 77) DTCS code (p. 75) DIGITAL DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY DIGITAL Bank link setting*1 (p. 77) DTCS polarity (p. 75) Auto power-off (p. 81) DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY Squelch attenuator DIGITAL (p. 82) Wide/Nar. selection*3 (p. 78) Offset frequency (p. 76) 17 Repeater lockout DIGITAL DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY (p. 81) ALC function (p. 82) DIGITAL Reverse mode (p. 76) AM/FM mode select (p. 78) DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY Squelch delay (p. 81) 2 Tuning step (p. 76) Weather alert* (p. 78) 94
  • #02 Europe <Intended Country of Use> #12 Europe-1 I GER I FRA I ESP I SWE I AUT I NED I POR I DEN I GBR I BEL I ITA I FIN I IRL I LUX I GRE I SUI I NOR A-6329H-1EX Printed in Japan 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan © 2003 Icom Inc.