Learn PLC & Drives Online
Upcoming SlideShare
Loading in...5
×
 

Learn PLC & Drives Online

on

  • 2,695 views

This presentation explains:

This presentation explains:

How NFI deliver Online PLC Classes?
Online Training Content
Extra Benefits

Statistics

Views

Total Views
2,695
Views on SlideShare
1,904
Embed Views
791

Actions

Likes
2
Downloads
89
Comments
0

2 Embeds 791

http://www.nfiautomation.org 413
http://nfiautomation.org 378

Accessibility

Upload Details

Uploaded via as Adobe PDF

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

    Learn PLC & Drives Online Learn PLC & Drives Online Presentation Transcript

    • nfi LEARN PLC ONLINE for Design, Simulate & Run Transforming knowledge into education nfi Online Learning Methodology Free Software E- Certificate Free Circuits Motivational Learning Environment NFI – Industrial Automation Training Academy nfiautomation.org
    • www.nfiautomation.org Training Course PLC & Drives Certified Course Lesson 1 – PLC – Wiring & Programming Topic Software LIVE Hardware Demo Videos Available PLC Wiring Fundamentals Automation Studio No Yes PLC Programming (Basics) WPL Soft No Yes PLC Programming (Advanced) WPL Soft No Yes WPL Soft & Automation Studio No No Test nfi
    • www.nfiautomation.org Training Course PLC & Drives Certified Course Lesson 2 – 35 Delta PLC Programming Videos LD (NO Contact) Retentive Timer PLF (Falling Pulse Output) LDI (NC Contact) Subroutine MC, MCR OUT (Output) Step Commands Call Jump (CJ) SET (Set) Interrupts Invert Command RST (Reset) LDP (Rising Edge) Pulse Width Modulation LD=, LD>, LD< LDF (Falling Edge) Sequencer CMP (Compare) Mov (Move Command) Up-Down Counter CZP (Zone Compare) INC (Increment) Block Move TMR (Timer) DEC (Decrement) Fill Move CNT (Counter) PLS (Rising Pulse Output) ADD, SUB, MUL, DIV
    • This is a PLC Input Terminals FREE Presentation for Download PLC Troubleshooting & Maintenance Output Terminals D/A Card Programming Cable A/D Card RS 485
    • www.nfiautomation.org Training Course PLC & Drives Certified Course Lesson 2 – 24 Allen Bradley PLC Programming Videos XIO Increment & Decrement Sequencer Compare XIC Arithmetic FIFO Load & Unload OUT Scaling LIFO Load & Unload Latch/ Unlatch Copy & Fill Encoding & Decoding RST (Reset) Move with Masked High Speed Counter OSR (One Shot Rising) Jump Label Timers TOD & FRO Counters Jump Subroutine Comparison TND & MCR Data Registers Sequencer
    • This is a PLC FREE Presentation for Download PLC Allen Bradley Micrologix Input Terminals Programming Cable Output Terminals Power 24 VDC
    • www.nfiautomation.org Training Course PLC & Drives Certified Course Lesson 3 – PLC Box Sorting Project Topic Software LIVE Hardware Demo Videos Available Introduction to ITS PLC PE ITS PLC PE No Yes PLC Box Sorting Project Mission: Automatic Sorting of Boxes on Conveyor based on Height ITS PLC PE WPL Soft No Yes ITS PLC PE WPL Soft No No 5 Tasks Test nfi
    • This is a PLC Power 24 VDC Battery Input Terminals Output Terminals FREE Presentation for Download Programming Cable PLC Siemens S7 200
    • Authorized Access to NFI Knowledge Portal that have hundreds of Circuits, & Q/A
    • Downloadable PLC test & Solutions
    • LEARN PLC & Drives Design, Simulate & Run ONLINE for Advanced Course LIVE SESSIONS nfi Transforming knowledge into education nfi Free Software E- Certificate Free Circuits Motivational Learning Environment NFI – Industrial Automation Training Academy nfiautomation.org
    • www.nfiautomation.org Training Course PLC & Drives Certified Course Lesson 1 – Basic Industrial Control Topic Software LIVE Hardware Demo Videos Available Basic Fundamentals of Electronics & Electrical Automation Studio None No Sensor Fundamentals Limit Switches, Proximity, Color Sensor Automation Studio Yes Yes Relay Logic Control- Latching & Interlocking Automation Studio Yes No AC Motor Control using Contactor Automation Studio Yes No Sensor Relay Interfacing Automation Studio Yes No Test Automation Studio Yes No nfi
    • www.nfiautomation.org Training Course PLC & Drives Certified Course Lesson 4 – PLC Analogue Inputs/Outputs Topic Software LIVE Hardware Demo Videos Available Understanding Analog Signals 0 ~ 10 VDC 4 ~ 20 mA WPL Soft Yes No Reading Analog Signal (0 ~ 10 VDC) into PLC Analog Voltage Source: Potentiometer VFD Feedback Signal Use of Delta DVP 04AD WPL Soft Yes No Writing Analog Signal (0 ~ 10 VDC) from PLC Analog Outputs: VFD , Multimeter Use of Delta DVP 04DA WPL Soft Yes No Test WPL Soft Yes No nfi
    • www.nfiautomation.org Training Course PLC & Drives Certified Course Lesson 5 – Drives – Variable Frequency Drives (Basics) Software LIVE Hardware Demo Videos Available Introduction to VFD - Principle & its Parts/Terminals- How VFD saves Energy? Introduction to Delta L – Series- Flexible Trainer None Yes No Connection with Motor & Main Terminals Main Terminal Connection – Direct Use to Toggle Switch to Start/Stop the Drive Use of Relay to Start/Stop the Drive Connection of Motor Terminals/ Ratings None Yes No Source of Frequency Command – Explanation of all Sources None Yes No Source of Operation Command – Explanation of all Sources – Including 2 Wire/ 3 Wire Control None Yes No Test None None No Topic nfi
    • www.nfiautomation.org Training Course PLC & Drives Certified Course Lesson 6 – Drives – Variable Frequency Drives (Advanced) Software LIVE Hardware Demo Videos Available RUN/ Stop of VFD using Sensors None Yes No Automatic To & Fro motion of VFD using Limit Switch None Yes No Source of Frequency Command – Study of all Sources None Yes No Source of Operation Command – Study of all Sources – Including 2 Wire/ 3 Wire Control None Yes No Stop Method/ Acceleration Time/ Dec Time None Yes No Jog Operation/ Multi Speed Operation – Speed Change by Sensors None Yes No Test None No No Topic nfi
    • www.nfiautomation.org Training Course PLC & Drives Certified Course Lesson 6 – Drives – Variable Frequency Drives (Advanced) Software LIVE Hardware Demo Videos Available Internal PLC Operation – Step Frequency/Timing Control None Yes No Feedback Signal from VFD None Yes No Synchronization of VFD’s None Yes No VFD By pass/ Emergency Stop None Yes No Stop Method/ Acceleration Time/ Dec Time None Yes No VFD Faults & troubleshooting None Yes No PLC- VFD Control – Control & Monitoring VFD Operation using PLC None Yes No PLC/HMI- VFD MODBUS Communication None Yes No Course Review None Yes No Topic nfi
    • SCAN & GET Discount Code www.nfiautomation.org/Online