Rv park Whotspot network kit

IntroductionAll RV parks provide wireless Internet for guests. The important requirements for a WiFi wireless Internet Hotspot are:• Good wireless coverage throughout the property so visitors can connect anywhere• A login page with a disclaimer that can be changed• A landing page so that visitors are taken to the business website after login• Optional facility to create access codes and limit the Internet service to paying guests• Bandwidth control to prevent any visitor overloading the system• Content filter to ensure that Internet access is family friendly, some websites blocked• Firewall to prevent hackers getting access to the business computers• Timer-calendar to disable the Hotspot at specific times or days• Easy installation: no specialist network knowledge required The installation project and kit described in this document will provide good wireless coverage for a small to medium size RV park. For larger RV parks additional wireless equipment can be installed. Copyright © Guest Internet Solutions, 2011. All Rights Reserved 2

Guest Internet RV park starter kit contentsKit Contents:• GIS-R2 hotspot gateway with power supply• High Power outdoor wireless access points, Bullet 2HP• Power over Ethernet supply (PoE) for the wireless access point• Omni-directional antenna with pole mounting bracket• Three Ethernet cables, two of 3ft and one of 25ftCustomer provides:• Ethernet cable between the GIS-R2 and the wireless access point if the length exceeds 25ft Copyright © Guest Internet Solutions, 2011. All Rights Reserved 3

EquipmentUbiquiti Bullet 2HP Hotspot gateway GIS-R2Power output 800mW. The most 1 x 10/100 Ethernet port to DSL/ Cablepowerful access point currently 4 x 10/100 Ethernet ports for switchedavailable for long range outdoor and wireless access pointsapplicationsAccessories8dBi omni-directional antennawith pole mount bracketThree Ethernet cablesPower supplies Copyright © Guest Internet Solutions, 2011. All Rights Reserved 4

Wireless access point and antenna installation Antenna The wireless access point and antenna assembly fixes to the mast with the clamp provided. The antenna should be mounted as high as possible Wireless access point Copyright © Guest Internet Solutions, 2011. All Rights Reserved 6

Custom login pages• The GIS-R2 can have a custom login page installed: the custom login page is created using HTML programming by a web site designer Copyright © Guest Internet Solutions, 2011. All Rights Reserved 9

Installation step 1 • Install the wiring from the location of the DSL/cable router to the wireless access point/antenna • If the 25ft cable supplied is not long enough then a longer cable should be purchased or assembled • If the cable is assembled use a cable tester to verify that it is correct 25ft cable Copyright © Guest Internet Solutions, 2011. All Rights Reserved 10

Installation step 2 • Configure the GIS-R2 as shown on the Quick Start Guide Hotspot Gateway Product Setup - Quick Start Guide 1 Download the product manual at: http://www.guest-internet.com/gateway The Guest Internet GIS-R2 WiFi Hotspot Internet gateway product has four Ethernet ports that can be used to First Time Product Configuration connect wireless access points, Internet café kiosk computers, wired hotel rooms and business center computers. The Internet port must be connected to the DSL or cable modem Connect your laptop computer to one of the LAN ports of the GIS-R2. First connect the GIS-R2 Connect the Internet port to you DSL router. as shown in the diagram Open your computer browser. Instead of your login page you will see the to configure it using the page shown below. This page is the SETUP WIZARD. setup wizard. GIS-R2 Configuration GIS-R2 Connect your computer Ethernet connector to the LAN1 connector of the GIS-R2. Your computer Ethernet LAN port connector should be DSL configured for dynamic Internet port IP or as a DHCP client. It cannot be used with a fixed IP. Internet Connect the Internet connector of the GIS-R2 to the DSL or cable Configuration computer modem LAN Ethernet connector. The DSL of Hotspot Gateway Product Setup - Quick Start Guide 2 cable modem should Download the product manual at: http://www.guest-internet.com/gateway have the LAN network connector configured as Step 1: test the Internet access Step 2: set the wireless WiFi hotspot name Step 4: select free or paid access a DNCP server. Check GIS-R2 Application with the equipment GIS-R2 Your wireless unit must have a connection to the Internet Type in an appropriate name that will help your guests find If you select free access then your guests will click on a manual to verify the for the configuration process. If you see a green YES then your wireless network. disclaimer to access the Internet. If you select paid LAN connector proceed to step 2. If a red NO then click on the link to access then you will generate access codes using the configuration. diagnose the problem. The setup process has four steps. Follow the instructions to type in the menu option and sell these access codes to your guests. For operation the WiFi Wireless Internet DSL information requested on each page. Then click on the button to go to the Hotspot users will use circuit next page. When the setup process is completed You may need the help of a network technician to make your personalized the wireless network wireless Internet service will be ready for your guests Internetusing. The work. your to start connection or kiosk computers. setup process is shown overleaf: flip this page over to start the setup Connect wireless Switch process. You may have to set a ‘fixed IP’. Ask your network technician to provide this for you. access points and Internet kiosk computers to the GIS-R2 LAN ports. Login to the Admin pages at any time. Connect your computer to the GIS- Busine ss R2 via an Ethernet cable of wireless. Then open your browser and type in If you wish to connect center computer Wireless Internet the URL: more then 4 devices then connect a switch http://aplogin.com/admin to increase the The username is admin, and the password is the one that you entered number of ports. with the wizard. When the page opens select the option you need in the menu. See the Reset to Factory Defaults: With the GIS-R2 powered up, use a paperclip to press the reset button manual for more information about configuration. through the hole. Hold the reset button down for 10 seconds the release. All parameters will be reset. Support@guest-internet.com Copyright © Fire4 Systems Inc., 2009. All rights reserved. Step 3: type your business information Finished, click on reboot to start your hotspot Your guests will see this information on the login page After reboot wait two minutes then open your browser to see the login page you generated. If you want to make changes then login again as shown on the previous page. Charging for Internet access In addition to generating and selling codes, you can also sell scratch cards and purchase our credit cards processing option. Contact us for additional information. Support@guest-internet.com Copyright © Fire4 Systems Inc., 2009. All rights reserved. Copyright © Guest Internet Solutions, 2011. All Rights Reserved 11

Installation step 3 • Configure the wireless broadcast name (SSID) on the wireless access point. Use the RV park name for the hotspot: “RV park WiFi” • Set the computer IP to a fixed address • 192.168.1.2 Wireless access point configuration • Open the browser and type a fixed IP address into the URL line • 192.168.1.20 • A password box will open • Username: ubnt • Password: ubnt LAN port • The configuration screen will be displayed • Click on ‘wireless settings’ in the menu • Change the SSID name to the name selected, Configuration e.g. ‘RV park WiFi’ computer Copyright © Guest Internet Solutions, 2011. All Rights Reserved 12

Installation step 4 • Install the wireless access point on the mast, connect to the PoE power supply and connect that to the GIS-R2 • Check that the LED lights are glowing on the wireless access point • Check that both the orange and blue LED’s are glowing on the GIS-R2 Copyright © Guest Internet Solutions, 2011. All Rights Reserved 13

RV receivers• Install a WiFi Boost unit in Distance up each RV to 5 miles line of sight• The range between the central antenna and each RV site is greatly extended WIFI-BOOST power outlet Ethernet cable (Up to 300ft) 12v Power cord Laptop computer Copyright © Guest Internet Solutions, 2011. All Rights Reserved 14

Rv park Whotspot network kit

by Guest Internet

Accessibility

Categories

Upload Details

Usage Rights

Statistics

Rv park Whotspot network kit Presentation Transcript