LG Commercial Front End Dryer User Manual

8,832
-1

Published on

LG Electric & Gas Dryer Service Manual
http://equipesolutions.net.au/lg-commercial-dryers.html

Published in: Self Improvement, Business
0 Comments
3 Likes
Statistics
Notes
  • Be the first to comment

No Downloads
Views
Total Views
8,832
On Slideshare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
136
Comments
0
Likes
3
Embeds 0
No embeds

No notes for slide

LG Commercial Front End Dryer User Manual

  1. 1. ELECTRIC & GAS DRYERSERVICE MANUALCAUTIONREAD THIS MANUAL CAREFULLY IN ORDER TOPROPERLY DIAGNOSE PROBLEMS AND TO SAFELY SIGNPROVIDE QUALITY SERVICE ON THESE DRYERS. DEMODEL : RN1329AN1/RV1329AN1 RN1329AN4/RV1329AN4 ER C D TIFIE RN1329AN7/RV1329AN7 RN1329AD6/RV1329AD6 RN1329AD1/RV1329AD1 RN1329AD5/RV1329AD5 RN1329A1/RV1329A1 RN1329A4/RV1329A4 RN1329A7/RV1329A7
  2. 2. April 2011 PRINTED IN KOREA P/No. : MFL62119935
  3. 3. IMPORTANT SAFETY NOTICEThe information in this service guide is intended for use by individuals possessing skill and experience inelectrical, electronic, and mechanical appliance repair. Any attempt to repair a major appliance may resultin injury to persons and property damage. The manufacturer or seller cannot be responsible for theinterpretation of this information, nor can it assume any liability in connection with its use. ! WARNING To avoid injury to persons disconnect power before se rvicing this product. If electrical power is required for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks. RECONNECT ALL GROUNDING DEVICES If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for service, they must be returned to their original position and properly fastened. WHAT TO DO IF YOU SMELL GAS: ■ Do not try to light a match, or cigarette, or turn on ■ Immediately call your gas supplier from a neighborís any gas or electrical appliance. phone. Follow the gas supplierís instructions ■ Do not touch any electrical switches. Do not use any carefully. phone in your building. ■ If you cannot reach your gas supplier, call the fire ■ Clear the room, building or area of all occupants. department. IMPORTANT Electrostatic Discharge (ESD) Sensitive Electronics ESD problems are present everywhere. ESD may damage or weaken the electronic control assembly. The new control assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress. ■ Use an anti-static wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the appliance. - OR - Touch your finger repeatedly to a green ground connection point or unpainted metal in the appliance. ■ Before removing the part from its package, touch the anti-static bag to a green ground connection point or unpainted metal in the appliance. ■ Avoid touching electronic parts or terminal contacts. Handle electronic control assembly by edges only. ■ Observe above instructions when repackaging failed electronic control assembly in an anti-static bag. 2
  4. 4. CONTENTS1. IMPORTANT SAFETY INSTRUCTIONS .............................................................................. 42. SPECIFICATIONS ................................................................................................................ 93. FEATURES AND BENEFITS .............................................................................................. 114. INITIAL STEPS FOR INSTALLING YOUR DRYER ............................................................ 135. INSTALLATION INSTRUCTIONS ....................................................................................... 196. ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS ............................................ 297. ELECTRICAL REQUIREMENTS FOR GAS DRYERS ...................................................... 378. GAS REQUIREMENTS AND INSTRUCTIONS .................................................................. 389. EXHAUST REQUIREMENTS AND MAINTENANCE .......................................................... 3910. DRYER CYCLE PROCESS ............................................................................................. 4311. COMPONENT TESTING INFORMATION ....................................................................... 4412. MOTOR DIAGRAM AND SCHEMATIC............................................................................. 4713. CONTROL LAYOUT ........................................................................................................ 4814. WIRING DIAGRAM ........................................................................................................... 4915. DIAGNOSTIC TEST.......................................................................................................... 50 15-1. TEST 1 240V AC ELECTRICAL SUPPLY ............................................................ 51 15-2. TEST 2 THERMISTOR TEST ................................................................................ 54 15-3. TEST 3 MOTOR TEST ......................................................................................... 55 15-4. TEST 4 MOISTURE SENSOR............................................................................... 56 15-5. TEST 5 DOOR SWITCH TEST.............................................................................. 57 15-6. TEST 6 HEATER SWITCH TEST - ELECTRIC MODEL ....................................... 58 15-7. TEST 7 GAS VALVE TEST - GAS MODEL .......................................................... 5916. ERROR MODE ................................................................................................................ 6017. CHANGE GAS SETTING (NATURAL GAS, PROPANE GAS) ....................................... 6118. DISASSEMBLY INSTRUCTIONS .................................................................................... 6319. EXPLODED VIEW ........................................................................................................... 71 19-1-1. Control Panel & Plate Assembly - Coin Type ....................................................... 71 19-1-2. Control Panel & Plate Assembly - Card Type ....................................................... 72 19-2-1. Cabinet & Door Assembly - Electric Stack Upper Type ........................................ 73 19-2-2. Cabinet & Door Assembly - Electric Stack Lower Type ........................................ 74 19-2-3. Cabinet & Door Assembly - Gas Stack Upper Type ............................................. 75 19-2-4. Cabinet & Door Assembly - Gas Stack Lower Type ............................................. 76 19-3-1. Drum & Motor Assembly: Electric Type ................................................................ 77 19-3-2. Drum & Motor Assembly: Gas Type ..................................................................... 78 3
  5. 5. 1 IMPORTANT SAFETY INSTRUCTIONSREAD ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual must be followed to minimize the riskof fire or explosion, electric shock, or to prevent property damage, injury to persons , or death. Your Safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER or WARNING. These words mean: DANGER: You can be killed or seriously injured if you don’t immediately follow instructions. WARNING: You can be killed or seriously injured if you don’t follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.BASIC SAFETY PRECAUTIONS WARNING: To reduce the risk of fire, electric shock, or injury to persons when usingthis appliance, follow basic precautions, including the following:• Read all instructions before using the dryer. discarded, remove the door to the drying• Before use, the dryer must be properly installed as compartment. described in this manual. • Do not allow children to play on or in the dryer.• Do not place items exposed to cooking oils in your Close supervision of children is necessary when dryer. Items contaminated with cooking oils may the dryer is used near children. contribute to a chemical reaction that could cause • Do not use fabric softeners or products to a load to catch fire. eliminate static unless recommended by the• Do not dry articles that have been previously manufacturer of the fabric softener or product. cleaned in, washed in, soaked in, or spotted with • Do not use heat to dry articles containing foam gasoline, dry-cleaning solvents, or other rubber or similarly textured rubber-like materials. flammable or explosive substances as they give • Keep area around the exhaust opening and off vapors that could ignite or explode. adjacent surrounding areas free from the• Do not reach into the dryer if the drum or any other accumulation of lint, dust, and dirt. part is moving. • The interior of the dryer and exhaust vent should• Do not repair or replace any part of the dryer or be cleaned periodically by qualified service attempt any servicing unless specifically personnel. recommended in this Use and Care Guide or in • Do not install or store the dryer where it will be published user-repair instructions that you exposed to the weather. understand and have the skills to carry out. • Always check the inside of the dryer for foreign• Do not tamper with controls. objects.• Before the dryer is removed from service or • Clean lint screen before or after each load. 4
  6. 6. READ ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual must be followed to minimize the risk offire or explosion, electric shock, or to prevent property damage, injury to persons, or death.• Do not store or use gasoline or other flammable • Installation and service must be performed by a vapors and liquids in the vicinity of this appliance or qualified installer, service agency, or the gas any other appliances. supplier.WHAT TO DO IF YOU SMELL GAS:1. Do not try to light a match or cigarette, or turn on 4. Immediately call your gas supplier from a any gas or electrical appliance. neighbor’s phone. Follow the gas supplier’s2. Do not touch any electrical switches. Do not use instructions carefully. any phone in your building. 5. If you cannot reach your gas supplier, call the fire3. Clear the room, building, or area of all occupants. department.CALIFORNIA SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACTThis act requires the governor of California to publish a list of substances known to the state tocause cancer, birth defects, or other reproductive harm and requires businesses to warn customersof potential exposure to such substances.Gas appliances can cause minor exposure to four of these substances, namely benzene, carbonmonoxide, formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas orLP fuels.Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances canbe minimized further by properly venting the dryer to the outdoors. 5
  7. 7. READ ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual must be followed to minimize the riskof fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.GROUNDING INSTRUCTIONSThis appliance must be grounded. In the event of person if you are in doubt as to whether themalfunction or breakdown, grounding will reduce the appliance is properly grounded.risk of electric shock by providing a path of least Do not modify the plug provided with the appliance.resistance for electric current. This appliance must If it will not fit the outlet, have a proper outletbe equipped with a cord having an equipment- installed by a qualified electrician.grounding conductor and a grounding plug. The plugmust be plugged into an appropriate outlet that is This appliance must be connected to a groundedproperly installed and grounded in accordance with metal, permanent wiring system or an equipment-all local codes and ordinances. grounding conductor must be run with the circuit conductors and connected to the equipment- WARNING — Improper connection of grounding terminal or lead on the appliance.the equipment-grounding conductor can result in a Electric shock can result if the dryer is not properlyrisk of electric shock. Check with a qualified grounded.electrician or serviceSAFETY INSTRUCTIONS FOR INSTALLATION WARNING To reduce the risk of fire, electric shock, or injury to persons when using thisappliance, follow basic precautions, including the following:• Properly ground dryer to conform with all • To reduce the risk of electric shock, do not governing codes and ordinances. Follow details install the dryer in humid spaces. Failure to in the installation instructions. Electric shock can follow this warning can cause serious injury, fire, result if the dryer is not properly grounded. electric shock, or death.• Before use, the dryer must be properly • Connect to a properly rated, protected, and installed as described in this manual. sized power circuit to avoid electrical overload. Electric shock can result if the dryer is not properly Improper power circuit can melt, creating electric grounded. shock and/or fire hazard.• Install and store the dryer where it will not be • Remove all packing items and dispose of all exposed to temperatures below freezing or shipping materials properly. Failure to do so can exposed to the weather. result in death, explosion, fire, or burns.• All repairs and servicing must be performed by • Place dryer at least 18 in. above the floor for a an authorized servicer unless specifically garage installation. Failure to do so can result in recommended in this Owner’s Guide. Use only death, explosion, fire, or burns. authorized factory parts. Failure to follow this • Keep all packaging from children. Packaging warning can cause serious injury, fire, electric material can be dangerous for children. There is a shock, or death. risk of suffocation. 6
  8. 8. READ ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual must be followed to minimize the riskof fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.SAFETY INSTRUCTIONS FOR INSTALLATIONExhaust/Ducting:• Gas dryers MUST be exhausted to the outside. • The openings must not beobstructed by a carpet. Failure to follow these instructions can result in fire or • Rigid or semi rigid metal ducting is recommended death. for use between the dryer and the wall. In special• The dryer exhaust system must be exhausted to installations when it is impossible to make a the outside of the dwelling. If the dryer is not connection with the above recommendations, a exhausted outdoors, some fine lint and large UL-listed flexible metal transition duct may be amounts of moisture will be expelled into the used between the dryer and wall connection only. laundry area. An accumulation of lint in any area of The use of this ducting will affect drying time. the home can create a health and fire hazard. Failure to follow these instructions can result in fire or• Use only rigid metal or flexible metal 4-in. death. diameter ductwork inside the dryer cabinet or for • Do not use sheet metal screws or other fasteners exhausting to the outside. Use of plastic or other which extend into the duct that could catch lint combustible ductwork can cause a fire. Punctured and reduce the efficiency of the exhaust system. ductwork can cause a fire if it collapses or becomes Secure all joints with duct tape. For complete otherwise restricted in use or during installation. details, follow the Installation Instructions. Failure• Ductwork is not provided with the dryer, and you to follow these instructions can result in fire or death. should obtain the necessary ductwork locally. • Keep the area underneath and around your The end cap should have hinged dampers to appliances free of combustible materials such as prevent backdraft when the dryer is not in use. lint, paper, rags, chemicals, etc. Failure to do so Failure to follow these instructions can result in fire or can result in fire. death.• The exhaust duct must be 4 in. (10 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow these instructions can result in fire or death. 7
  9. 9. READ ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual must be followed to minimize the riskof fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY WARNING: To reduce the risk of fire, electric shock, or injury to persons when using thisappliance, follow basic precautions, including the following:• Do not, under any circumstances, cut or • Never unplug your dryer by pulling on the remove the ground prong from the power cord. power cord. Always grip plug firmly and pull To prevent injury to persons or damage to the straight out from the outlet. The power cord can dryer, the electrical power cord must be plugged be damaged, resulting in a risk of fire and electric into a properly grounded outlet. shock.• For personal safety, this dryer must be • Repair or replace immediately all power cords properly grounded. Failure to do so can result in that have become frayed or otherwise electric shock or injury. damaged. Do not use a cord that shows cracks• Refer to the installation instructions in this or abrasion damage along its length or at manual for specific electrical requirements for either end. The power cord can melt, creating your model. Failure to follow these instructions electric shock and/or fire hazard. can create an electric shock hazard and/or a fire • When installing or moving the dryer, be careful hazard. not to pinch, crush, or damage the power cord.• This dryer must be plugged into a properly This will prevent injury and prevent damage to the grounded outlet. Electrical shock can result if dryer from fire and electric shock. the dryer is not properly grounded. Have the • To reduce the risk of injury to persons, wall outlet and circuit checked by a qualified adhere to all industry recommended safety electrician to make sure the outlet is properly procedures including the use of long sleeved grounded. Failure to follow these instructions can gloves and safety glasses. Failure to follow all of create an electric shock hazard and/or a fire the safety warnings in this manual could result in hazard. property damage, injury to persons or death.• The dryer should always be plugged into its • Connect the power cord to the terminal block. own individual electrical outlet which has a Each colored wire should be connected to voltage rating that matches the rating plate. same color screw. Wire color indicated on This provides the best performance and also manual is connected to the same color screw prevents overloading house wiring circuits which in block. Failure to follow these instructions may could cause a fire hazard from overheated wires. result in a short or overload. SAVE THESE INSTRUCTIONS 8
  10. 10. 2 SPECIFICATIONS ■ Type : Electric and Gas Dryer ■ Rating : Please refer to the rating label regarding detailed information. ■ Size : 686mm(W) x 764mm(D) x 983mm(H) ■ Capacity : 10Kg ■ Weight : 59.4 kg ❋ Specifications are subject to change by manufacturer. 9
  11. 11. RV1329AN1 RN1329AN1 RV1329AN4 RN1329AN4 RV1329AN7 RN1329AN7 RV1329AD6 RN1329AD6 ITEM RV1329AD1 RN1329AD1 REMARK RV1329AD5 RN1329AD5 RV1329A1 RN1329A1 RV1329A4 RN1329A4 RV1329A7 RN1329A7 TYPE Electric Gas (LNG) POWER SUPPLY 240V, 17Amps - Color Blue white Porcelain :RV1329AN4/RN1329AN4 RV1329AD1/RN1329AD1 Top Plate Painted MATERIAL & RV1329A4/RN1329A4 FINISH Door Trim Stainless Deco (Hair line) Door Frame Chrom C/Panel Color Blue white MOTOR 250W (4.5V) AC 240V ELECTRICITYCONSUMPTION HEATER 4000W (17A) - AC 240V GAS VALVE - - CONTROL TYPE Electronic DRUM CAPACITY 10Kg Weight (lbs.) - Net/Gross 126/144 No. of Programs 4 Audible End of Cycle Beeper Available Time dry Available Reversible Door Available Drum Stainless Steel Product (WxHxD) 686mm(W) x 764mm(D) x 983mm(H) Packing (WxHxD) 744mm(W) x 385mm(D) x 1140mm(H) 10
  12. 12. 3 FEATURES AND BENEFITS ■ CARD TYPE - SIDE BY SIDE(RN1329AD1, RV1329AD1) - STACK UPPER(RN1329AD5, RV1329AD5) - STACK LOWER(RN1326AD6, RV1326AD6) 4 1 2 3 ■ OPL TYPE - SIDE BY SIDE(RN1329A4, RV1329A4) - STACK UPPER(RN1329A7, RV1329A7) - STACK LOWER(RN1326A1, RV1326A1) 4 1 2 31. DISPLAY LED 3. START BUTTON2. CYCLE BUTTON 4. STATUS LED 11
  13. 13. ■ COIN TYPE - SIDE BY SIDE(RN1329AN4, RV1329AN4) 4 1 2 3■ COIN TYPE - STACK UPPER(RN1329AN7, RV1329AN7) 4 1 2 3■ COIN TYPE - STACK LOWER(RN1329AN1, RV1329AN1) 4 1 2 3 1. DISPLAY LED 3. START BUTTON 2. CYCLE BUTTON 4. STATUS LED 12
  14. 14. 4 INITIAL STEPS FOR INSTALLING YOUR DRYER The following instructions will help guide you through the initial steps of setting up your dryer for use. Please note that every section of this manual provides important information regarding the preparation and use of your dryer, and it is important that you review this entire manual before proceeding with any installation or use. More detailed instructions concerning electrical connections, gas connections, and exhaust requirements are provided at other parts of this manual. STEP 1 Positioning the Dryer. Certain minimum clearances are required above, behind, and to the sides of the unit, as Choose a location with a solid floor for your dryer. shown below. Those required minimum clearances Place the dryer at least eighteen inches above the are set forth in the picture below. Please also keep the floor for a garage installation. After placing the following instructions in mind when installing in a dryer in the desired location, please make sure that closet or recessed area: it has the required clearances shown below, and Consider allowing additional clearance for sections on Exhaust and Maintenance requirements. installation and servicing. Wall, door and floor molding may force additional clearances. An additional inch of clearance is recommended to 49.8¡± minimize noise transfer . (126.4 cm) Consider space needed for companion appliances. 38.7¡± For closet installations, the picture below shows the(98.3 cm) minimum required ventilation openings for the door. A louvered door with comparable ventilation openings is also acceptable. ventilation 27¡± 29.96¡± hole (68.6 cm) (76.1 cm) * Most installations require a minimum 5 1/2 in. (14 cm) clearance behind the dryer for the exhaust vent with elbow. Note Level the dryer using the leveling legs and tighten ventilation the adjusting nuts to hold them in place. hole r. Closet door Closet-Side view If the d ryer is not level, the clothes will not tumble properly and the sensor will not be able to de tect the dryness level accurately. Adjust the le veling legs carefully to avoid injury. Note No other fuel-burning appliance shall be installed in the same closet as the drye r. This applies only to dryers suitable for installation in a closet. WARNING The applian ces are he avy. Two or more people a re requi red when moving or installing the appliance. 13 Closet-Front view There is a risk of serious back injury or other injuries.
  15. 15. Once in position, adjust the leveling legs of the dryer All four leveling feet must rest solidl y on theuntil it is level from left to right and from front to floo r. Gently push on the top co rners of theback. The leveling legs must remain firmly on the dryer to make sure that the dryer doe s not rock f rom co rner to co rner.floor and the dryer should not rock. The maximum If you are installing the dryer on the optionalslope of the dryer from left to right or from front to pedestal, you must use the leveling feet on theback should not exceed 2.5 cm (1 inch). If the dryer pedestal to level the dryer. The dryer leveling feetis not level, and if the slope exceeds 2.5 cm (1 inch), should be fully retracted.a load may not tumble properly and internal sensorsmay malfunction. Note: Other sections of thismanual also provide important informationconcerning the placement of and clearances for yourdryer. Please review this entire manual before STEP 2 Leveling the Dryer. wWARNING Use an adjustable or open ended spanner to turn the leveling feet. Turn clockwise to raise To ensure that the dryer provides optimal drying the dryer or counte rclockwise to lower it. performance, it must be level. To minimize Raise or lower the leveling feet until dryer is vibration, noise, and unwanted movement, the level from floor must be a perfectly level, solid surface. side to side and front to back. NOTE: Adjust the leveling feet only as far as Make sure that all 4 leveling feet are in firm necessary to level the dryer. Extending the contact with the floo r. leveling feet more than necessary can cause the dryer to vibrate. Level Leveling Feet Position the dryer in the final location. Place a level across the top of the dryer. 14
  16. 16. STEP 3 Procedure for Reversing the DoorThe door on your dryer can be installed to openeither to the left or the right. Follow theseprocedures to reverse the direction in which yourdoor opens: Note Door and l atch should be ali gned at the center when closed. O the rwise, the door will not open, close, or latch prope rly. ! 15
  17. 17. STEP 4 Connecting the Exhaust ° ALTERNATE EXHAUST DIRECTIONS and Venting System. 1. Remove the screw that attaches the ducts tab to the dryer. ! WARNING Use a heavy metal vent. Do not use plastic or thin foil duct. Clean old ducts before installing this dryer Failure to follow these instructions can result in death or fire. 2-1. Detach and remove the knockout that matches the desired venting direction Note (Right side not available on Gas Dryers) V Follow steps 1, 2, and 3, as shown smaller endsfacing away from the dryer. below. Incorrect installation of the vent and imp roper taping of the joi nts will interfere with correct d ryer and vent fun ction.In addition to the following warnings, please refer tomanual section on Exhaust Requirements andMaintenance. IMPORTANT: To reduce the risk of fire,combustion, and gas accumulation, the dryer must bevented to the outdoors. Please follow the instructions(and all others in this manual) very carefully. 2-2. Reconnect the duct to the blower housing and attach the duct to the base. The side vent kit is available as a service part, #383EEL9001B. Do not use plastic or thin foil duct. 3-1. Pre-assemble a 4 elbow with a 4 duct. Use 4 (10.2 cm) diameter rigid or semi-rigid Wrap duct tape around joint. metal duct (note: venting materials are not supplied with the dryer, and you must obtain the venting materials necessary for proper installation) Position the dryer so the exhaust duct run is as short as possible. Clean old ducts before installing this dryer The male end of each section of exhaust duct must point away from the dryer Use as few elbow joints as possible. 3-2. Insert the elbow duct assembly first through Use duct tape on all duct joints the side opening and connect the elbow to Insulate ductwork that runs through unheated the internal duct. areas in order to reduce condensation and lint build-up on pipe walls; and PLEASE BE AWARE THAT FAILURE TO EXHAUST THE DRYER CORRECTLY WILL VOID THE DRYER’S WARRANTY. 16
  18. 18. STEP 5 Connection of Gas Supply STEP 6 Electrical Plug Connection(Gas dryer only). In addition to the following, Following are several warnings and instructionsplease refer to manual section on Gas Requirements concerning making the electrical connection for electricand Instructions. dryers. More detailed information concerning the electrical connection is provided at the manual section entitled Electrical Requirements for Electric Dryer. 1 It is important that you thoroughly review that section, and the remainder of this manual before taking any 2 steps to install or use this dryer. 5 3 1. Use only a new U.L. listed No. 10 (copper wire only) three conductor power supply cord kit rated 240 4 1. New stainless steel flexible connector. Use this type of Volts (minimum) 30 Amperes and labeled as suitable connector only if allowed by local codes. Use Design AGA for use in a clothes dryer. Certified Connector. 2. Four-wire cord is required for manufactured (mobile) 2. 1/8 NPT Pipe Plug (for checking inlet gas pressure) home installations and use and where local codes do 3. Equipment Shut-Off Valve- not allow grounding of this appliance through Installed within 6(1.8m) of dryer neutral. 4. Iron Pipe. Shorter than 20(6.1m) Use 3/8 pipe. Longer than 20(6.1m) - Use 1/2 pipe. 3. Electrical Plug Connections. 5. 3/8 N.P.T. Gas Connection 4. For additional instruction on connecting the dryer to 6. Apply pipe joint compound or about 1 1/2 wraps of Teflon an electrical power source, please refer to this tape over all threaded connection manual’s section on Electrical Requirements and Note Electric Dryer. gas you are pr ovided with. Note Burner input requirements: Adjusting burner input setting is not needed (at the dryer will not have a ny problem with the BTU rating. If your house is at ab ove 10,000 feet, you are required to adjust a four percent (4%) reduction of the burner BTU rating indicated on the model/serial rating plate.1. Confirm that the type of gas available in your laundry WARNING room is appropriate for the dryer. The dryer is prepared for Natural Gas with a 3/8 NPT gas connection. !2. Remove the shipping cap from the gas connection at the • Use a new UL approved 30 amp power back of the dryer. Make sure that you don’t damage the supply cord or 10 gauge solid copper wire. threads of the gas connection pipe when you remove the • Use a UL approved strain relief. shipping cap. • Disconnect power before making electrical3. Connect the dryer to your laundry room’s gas supply connections. using a new flexible stainless steel connector (as noted • Connect neutral wire (white or center wire) below, only use a new stainless steel flexible connector if to center terminal. allowed by your local codes). • Ground wire (green or bare wire) must be4. Securely tighten all connections between the dryer and connected to green ground connector. your laundry room’s gas supply. Turn on your laundry • Securely tighten all electrical connections room’s gas supply and check all pipe connections (both • See installation instructions for complete internal and external) for gas leaks with a non-corrosive instructions. leak detection fluid. Refer to Part 7 (page 20) • Failure to do so can result in fire or electrical shock.5. For LP (Liquefied Petroleum) gas connection, refer to 17 this manual’s section entitled Gas Requirements and Instructions.
  19. 19. STEP 7 Preparation of the Dryer STEP 9 Dryer AirflowPrior to the first use of this appliance, use all- Effective dryer operation requires appropriate dryerpurpose cleaning products or a solution of detergent airflow. The adequacy of the airflow can beand water, with damp clothes to remove from the measured by evaluating the static pressure. Staticinside of the dryer drum/drying compartment any pressure in the exhaust duct can be measured with adust or dirt that may have accumulated the inside of manometer, placed on the exhaust ductthe dryer. Plug-in your dryer after reviewing the approximately 2 ft. (60.9 cm) from the dryer. Staticfollowing parts on your dryer’s Electrical pressure in the exhaust duct should not exceed 0.6Requirements. inches (1.5 cm). The dryer should be checked with the dryer running with no load. Measuring Static Pressure STEP 8 Confirming Heat Source OperationConfirming Heat Source in Gas Dryers ManometerClose the door to the dryer drum/dryingcompartment and, after completing all steps in thismanual for proper installation of this dryer, start thedryer on a heat setting, as described more fully inthe operating instructions that accompany the dryer.After the dryer starts, the igniter will glow red andthe main burner will ignite. Note If all air is not purged from the gas line, main burner have ignited. If this happens, the igniter will re-attempt gas ignition after approximately two minutes. Exhaust Duct MAXIMUM STATIC PRESSURE INConfirming Heat Source in Electric Dryers WATER COLUMNClose the door to the dryer drum/drying 0.6 inche (1.5 cm) WARNINGcompartment and, after completing all steps in thismanual for proper installation of this dryer, start the !dryer on a heat setting, as described more fully in • The dryer must be disconnected from thethe operating instructions that accompany the dryer. gas supply piping system during pressureThe exhaust air or the exhaust pipe should be warm testing.after the dryer has been operating for three minutes. • Failure to do so can result in death, explosion, or fire. 18
  20. 20. 4) Electric dryers may be vented to the outside STEP 9 Additional Instructions using the back, left, right, or bottom panel. for Installation of Your 5) Gas dryers may be vented to the outside using the Dryer in a Manufactured back, left, or bottom panel. Gas dryer may not be or Mobile Home. vented to the outside using the right side panel because of the burner housing. 6) The dryer exhaust duct must be affixed securelyThe following instructions are applicable to to the manufactured or mobile home structure,installations of the dryer in a manufactured or and the exhaust duct must be made of a materialmobile home. Any installation in a manufactured or that will resist fire and combustion, and it ismobile home must comply with the Manufactured recommended that you use a rigid or flexibleHome Construction and Safety Standards Title 24 metal pipe.CFR, Part 32-80 or Standard CAN/CSA0Z240 MHand local codes and ordinances. If you are 7) DO NOT connect the exhaust duct with any otheruncertain whether your proposed installation will duct, vent, chimney, or other exhaust duct.comply with these standards, please contact a 8) Make sure the dryer has adequate access toservice and installation professional for assistance. outside fresh air to ensure proper operation. The opening for outside fresh air must be at least 25 in2 (163 cm2).The following instructions apply to any installationof the dryer in a manufactured or mobile home: 9) It is important that the clearance of the duct from any combustible construction be at least 2 inches (5 cm), and, when venting the dryer to the1) The gas dryer must be permanently attached to outdoors, the dryer can be installed with a the floor. clearance of 1 inch at the sides and back of the2) The electrical connection for an electric dryer dryer. must be a 4-wire connection. More detailed 10) Please be aware that venting materials are not information concerning the electrical connection supplied with the dryer. You should obtain the is provided at the manual section entitled venting materials necessary for proper Electrical Requirements for Electric Dryer installation.3) To reduce the risk of combustion and fire, the dryer must be vented to the outside. WARNING WARNING Do not connect exhaust ducts with Do not vent the exhaust duct under the metal screws or fasteners that extend manufactured or mobile home. into the duct. 19
  21. 21. 5 INSTALLATION INSTRUCTIONSSingle Coin Card1 Coin/Card housingHow to connect the housingThe dryer has a connector for both a coin collector and a card reader. Use the one you need and tuck the other oneaway safely.2 COIN TYPE When power on the machine at ❇ first time without connecting card reader or coin housing ,display will show LqC1 Coin housing Card reader housing3 CARD TYPE (Single) WARNING • Disconnect power before service. • Failure to follow these instructions can result in death or electric shock. Note The Coin drop assembly operates on DC12V in dryer. The Card reader assembly operates on DC12V in dryer. 20
  22. 22. 4 STACK TYPE Installation Method (Dryer) - Coin Type Lower Stacking CoinDisassemble the control plate Disconnect the connectors. Remove 2 screwsDisassemble the top plate Remove 4 pieces 21
  23. 23. Installation Method (Dryer) – Coin Type Lower Stacking Coin Coin Harness – provided by Munzprufer Assemble the switchInsert the switch into the recess on the The connectors should be visible on theback of the coin box. Face it toward the rear of the box for connection to thefront so the coin box will press the button harness later. Connect the coin box switchwhen it is in place. at this time.Use an adhesive tie fastener and a cabletie to affix the service switch to the frontpanel. 22
  24. 24. Assemble the security bracketAttach the security lock bracket if it wasn’t Installed at the factory. Assemble the top plate Install the top plate on the dryer. 23
  25. 25. Installation Method (Dryer) – Coin Type Upper Stacking Coin Disassemble the control plate Remove the lower control panel. (Remember, this is the TOP dryer when they are stacked.) Stack the machine Disassemble the lowerStack the upper dryer onto panel frame Connect the boltthe lower dryer.Remove the lower panelfrom the upper dryer. 24
  26. 26. Disassemble the lower panel frame Remove the lower control panel. (Remember, this is the TOP dryer when they are stacked.)Coin Harness – provided by Munzprufer 25
  27. 27. Installation Method (Dryer) – Coin TypeStacking CoinCoin Drop – provided by MunzpruferInstall the double coin drop mechanism onto the back of the upper dryer control panel.Attach the bolts using the nuts provided.Connect the harness to the upper dryer and secure the wiring harness.Route the wiring to the lower control panel. Be careful to avoid confusing the upper andlower harness.After installing the coin drop module and coin box, replace the front panels on both machine.Be sure to secure all wiring harness parts to avoid vibration, pinching, chafing, or otherDamage using adhesive blocks and cable ties. 26
  28. 28. Assemble the control plate (Upper) Attach the control panel with the dual coin drop module to the bottom of top dryer. Assemble the control plate (Lower) Install security lockAttach the control panel withcoin drop box module to the topof the bottom dryer. 27
  29. 29. Install the stacking bracket at therear of the stacked dryers There are six (6) screws that hold the assembly in place.Installation Method (Dryer) – Card TypeStacking Card Different point between Coin type and Card type 28
  30. 30. Connect Gas Supply Pipe (Gas Dryer ONLY)For further assistance, refer to section on Gas Requirements.1. Make certain your dryer is equipped for use with the 3. Connect to gas supply pipe using a new flexible type of gas in your laundry room. Dryer is equipped stainless steel connector. at the factory for natural gas with a 3/8” NPT gas 4. Tighten all connections securely. Turn on gas and connection. check all pipe connections (internal external) for2. Remove the shipping cap from the gas connection gas leaks with a non-corrosive leak detection fluid. at the rear of the dryer. Make sure you do not 5. For L.P. (Liquefied Petroleum) gas connection, refer damage the pipe thread when removing the cap. to section on Gas Requirements. 1 2 5 3 4 1 New Stainless Steel Flexible Connector - Use 4 Black Iron Pipe only if allowed by local codes (Use Design Shorter than 20¡fl (6.1 m) - Use 3/8¡– pipe A.G.A. Certified Connector) Longer than 20¡fl (6.1 m) - Use 1/2¡– pipe 2 1/8¡– N.P.T. Pipe Plug 5 3/8¡– N.P.T. Gas Connection (for checking inlet gas pressure) 3 Equipment Shut-Off Valve-Installed within 6¡fl (1.8 m) of dryer 29
  31. 31. 6 ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERSCONNECTING ELECTRIC DRYERS! WARNING: To help prevent fire, electric shock, serious injury or death, the wiring andgrounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and allapplicable local regulations. Please contact a qualified electrician to check your home’s wiring andfuses to ensure that your home has adequate electrical power to operate the dryer.Electrical Requirements for Electric Models Only ! WARNING: To reduce the risk of fire, electric shock, or injury to persons when using thisappliance, follow basic precautions, including the following:• This dryer must be connected to a grounded • If branch circuit to dryer is 15 ft. (4.5 m) metal, permanent wiring system, or an or less in length, use UL (Underwriters equipment- rounding conductor must be run Laboratories) listed No.-10 AWG wire with the circuit conductors and connected (copper wire only), or as required by local to the equipment-grounding terminal or lead codes. If over 15 ft. (4.50 m), use UL-listed on the dryer. Failure to do so can result in fire, No.-8 AWG wire (copper wire only), or as explosion, or death. required by local codes. Allow sufficient• The dryer has its own terminal block that slack in wiring so dryer can be moved from must be connected to a separate 240V AC its normal location when necessary. Failure 50-Hertz, single-phase circuit, fused at 30 to do so can result in fire, explosion, or death. amperes (the circuit must be fused on both • The power cord (pigtail) connection between sides of the line). ELECTRICAL SERVICE wall receptacle and dryer terminal block FOR THE DRYER SHOULD BE OF THE IS NOT supplied with dryer. Type of pigtail MAXIMUM RATE VOLTAGE LISTED ON THE and gauge of wire must conform to local NAMEPLATE. DO NOT CONNECT DRYER TO codes and with instructions on the following 110-, 115-, OR 120-VOLT CIRCUIT. Heating pages. Failure to follow these instructions can elements are available for field installation result in fire, explosion, or death. in dryers which are to be connected to an • A 4-wire connection is required for all mobile electrical service of a different voltage than and manufactured home installations, as that listed on the rating plate. Failure to follow well as all new construction after January these instructions can result in fire, explosion, 1, 1996. A 4-wire connection must be used or death. where local codes do not permit grounding through the neutral wire. Failure to do so can result in fire, explosion, or death.Special Electrical Requirements for Mobile or Manufactured Homes ! WARNING: To reduce the risk of fire, electric shock, or injury to persons when using thisappliance, follow basic precautions, including the following:• Any installation in a manufactured or mobile • A 4-wire connection is required for all mobile home must comply with the Manufactured and manufactured home installations, as well Home Construction and Safety Standards as all new construction after January 1, 1996. Title 24 CFR, Part 32-80 or Standard CAN/ Failure to do so can result in fire, explosion, or CSA0Z240 MH and local codes and ordinances. death. 30
  32. 32. WARNING 31
  33. 33. WARNING 32
  34. 34. WARNING 33
  35. 35. WARNING 34
  36. 36. 35
  37. 37. 36
  38. 38. 7 ELECTRICAL REQUIREMENTS FOR GAS DRYERS 240 Volt, 50 Hertz, 60 Hertz, with 3-Prong Grounding PlugFollowing are additional instructions regarding electrical connections and requirements for gas dryers. WARNING: The wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1, and all applicable local regulations. Please contact a qualified electrician to check your homes wiring and fuses to ensure that your home has adequate electrical power to operate the dryer. Failure to do so can result in fire or electric shock.Electrical Requirements for Your Dryer:a) Please note that the wiring diagram is provided inside the dryer control hood. Label all wires prior to disconnection when servicing the dryer, because wiring errors can cause serious injury to you and your dryer.b) Your dryer is designed to be used on a separate branch, polarized, three-wire, effectively grounded, 240 Volt, 50 Hertz, AC (alternating current) circuit protected by a 17 Ampere fuse, equivalent fuse or circuit breaker.c) Use separately fused circuits for washers and STANDARD 240V Volt, 50 Hertz, 3-WIRE dryers, and DO NOT operate a washer and a EFFECTIVELY GROUNDED CIRCUIT dryer on the same circuit. 1 L1 WARNING 2 Ground • Do not overload the circuit by operating 3 Neutral Side 4 Round Grounding Prong other appliances on the same circuit 5 Neutral when this appliance is operating, by using an extension cord to connect the a) The dryer has a three-prong plug to help guard dryer to the power source, or by using against shock. The plug should be plugged any adapter to allow additional cords to directed into a properly grounded three-prong connect to the same outlet. receptacle that is rated 240Volts AC (alternating • Failure to do so can result in fire or current) 17 Amps. This plug, in order to be electric shock. properly and fully effective, must be plugged into a properly installed outlet that is grounded in accordance with all local codes and ordinances. b) The dryer must be grounded in order to reduce WARNING the risk of electric shock, including a • Do not modify the plug provided with malfunction or breakdown. the dryer. If it does not fit the outlet in c) If your laundry room does not meet the your laundry room, a proper outlet will specifications required by this manual, or if you need to be installed in your laundry are uncertain whether or not your laundry room room by a qualified service person or meets these specifications, please have a company. qualified service person or company. • Failure to do so can result in fire or Review your laundry room’s electrical supply for electric shock. any problems. 37
  39. 39. 8 GAS REQUIREMENTS AND INSTRUCTIONSFollowing are important instructions and information concerning the requirements for the gas supply and service forgas dryers. IMPORTANT WARNING: The gas supply and service for a gas dryer must comply with all localcodes and ordinances. In the absence of any local codes or ordinances in your area, the gas supply andservice for your gas dryer must comply with the latest edition of the National Fuel Gas Code, ANSIZ223.1/NFPA 54(USA) or Canadian gas installation code CAS B149.1(Canada).1. Gas supply requirements: Liquefied Petroleum 5. If using a rigid pipe, the rigid pipe should be 1/2 (L.P.) Gas (2,500 Btu/ft3 (93.1 MJ/m3)) service inch IPS. If acceptable under local codes and must be provided at 10 + 1.5 in. water column ordinances and when acceptable to your gas pressure. supplier, 3/8 inch approved tubing may be used where lengths are less than 20 feet (6.1 m).2. Do not attempt to connect the dryer to Liquified Larger tubing should be used for lengths in Petroleum (LP Gas) Gas service without a excess of 20 feet (6.1 m). It is also important that qualified professional. you use pipe joint compound that is insoluble in3. Isolate the dryer from the gas supply piping LP gas. system by closing its individual manual shut-off 6. To reduce the danger of gas leaks, explosion, and valve during any pressure testing of the gas fire, please follow and observe the following supply system at test pressure equal to or less instructions and WARNINGS. than 1/2 psi (3.45 kPa). • Connect the dryer to the type of gas shown on the4. Supply Line Requirements. Your laundry room nameplate. must have a rigid gas supply line to your dryer. In the United States, an individual manual shutoff • Use new flexible stainless steel connectors. valve MUST be installed within at least 6 feet • Use Teflon tape and pipe joint compound (1.8 m) of the dryer, in accordance with the insoluble in LP gas on all pipe threads. National Fuel Gas Code ANSI Z223.1 or • Purge gas supply of air and sediment before Canadian gas installation code CSA B149.1. connecting the gas supply to the dryer in order to A 1/8 in. N.P.T. pipe plug must be installed as prevent gas valve contamination. Before shown. tightening connection between gas supply and dryer, purge remaining air until odor of gas is identified. • DO NOT use an open flame to inspect for gas leaks; instead use a non-corrosive leak detection fluid. WARNING WARNING • Do not attempt any disassembly of the • Use a new AGA or CSA approved gas dryer. Any disassembly requires the supply line. attention and tools of an authorized • Install a shut-off valve. and qualified service person or • Securely tighten all gas connections. company. • If connected to LP, have a qualified • Failure to do so can result in person make sure gas pressure does not death,explosion, or fire. exceed 13 in. water column. • Examples of a qualified person include licensed heating personnel, authorized gas company personnel, and authorized service personnel. • Failure to do so can result in death, explosion, or fire. 38
  40. 40. 9 EXHAUST REQUIREMENTS AND MAINTENANCE 39
  41. 41. NATURAL MULTIPLE VENTING SYSTEM Over sum of area Over sum of area Over sum of area A + B+ C+ D A + B+ C A+B Over area A Exit Inspection Cap * Lg exhaust Duct Diameter: 100mm Use the exhaust duct over the inner diameter of exhaust pipe. Do not use too small inner diameter of exhaust pipe or too long exhaust duct, Because it makes bad ventilation and low drying performance and it will be cause of trouble. Follow the below guide in case of using gathering exhaust duct installed with over 2 duct. Incline the exhaust duct toward exit about an 45 angle when exhaust duct from dryer is connected to main exhaust duct. ( If you don’t make perpendicular connection, airflow is disturbed.) 40
  42. 42. FORCED MULTIPLE VENTING SYSTEMUse adjust damper to fit airflow velocity 5m/s at exit Blower Gas (Suction fan) Outdoor Dryer (Exit) Air flow velocity Adjust :5m/s Exhaust duct Damper Exhaust Main duct Exhaust Duct 41
  43. 43. Exhaust and Dryer Maintenance Cleaning the Lint Screen 1. Clean the lint filter either before drying each load or after drying each load. Always make sure the WARNING lint filter is clean before starting a new load, • Disconnect the dryer’s electric power because a clogged lint filter may increase drying prior to any cleaning or maintenance. times. • Failure to do so can result in fire or 2. To clean, pull the lint screen straight up and roll electric shock. any lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Push1. After one year of use, the interior and complete exhaust the lint screen firmly back into place. system of the dryer should be examined and cleaned if necessary. 3. Always ensure the lint screen is firmly secured before running the dryer. Running the dryer with2. Before one year of use, when drying performance has a loose lint screen may cause overheating and become unsatisfactory, please examine and clean the damage to the dryer and articles being dried. exhaust duct for better drying performance.3. Check the weather hoods frequently to ensure the 4. Some articles of clothing may shed more lint than dampers are moving freely, that the dampers are not others (towels for example), causing the lint pushed in and that nothing has been set against the screen to fill rapidly. Remove lint from the lint dampers. screen before and after drying these articles, such4. A qualified service person or company should be used as new towels. to perform this maintenance. 5. In the event lint falls off of the lint screen and5. A Flexible Metal Vent Kit, available at extra cost, can into the dryer during removal, inspect the exhaust be used to exhaust the dryer when it is placed in hard to hood and remove any lint. reach places. This Kit comes in two pieces, one of 6. Laundry detergent and fabric softener residue can which is attached to the dryer and the other is attached build up on the lint screen, causing longer drying to the wall exhaust outlet. Following attachment of the times. The screen is likely blocked if lint falls off two separate pieces to the dryer and the wall, the dryer the screen. In order to prevent this type of build may be returned to its final position, after which the up, and help ensure proper operation of your two pieces themselves can be connected. dryer, clean the lint screen with a nylon brush7. Ordinarily, the dryer drum will need no care. Wipe the every six months or, if necessary, more exterior of the dryer as required, and always wipe the frequently. The lint filter can also be washed as exterior of the dryer in the event any detergent, bleach, follows: or other washing products is spilled on the dryer. a) After rolling the lint off of the screen with your8. Clean the control panel with a damp cloth as fingers, wet both sides of the screen with hot or necessary. Warning: spray pre-wash products may warm water. damage the finish of the control panel.9. Please clean the lint filter either before drying each b) Wet a nylon brush with hot water and liquid load or after drying each load. detergent and scrub the lint screen with the brush10. Always make sure the lint filter is clean before to remove the buildup of detergent and fabric starting a new load, because a clogged lint filter may softener. increase drying times. c) After the residue has been removed, rinse screen11. Annually remove the lint filter and attach it to the with hot water. vacuum duct. See item #2 above. d) After drying the lint screen with a clean towel,12. Please note that the wiring diagram is provided inside firmly replace the lint screen in your dryer. the dryer control hood. Label all wires prior to disconnection when servicing the dryer, because wiring errors can cause serious injury to you and your dryer. 42
  44. 44. 10 DRYER CYCLE PROCESS Default Conditions of operation and termination Drying Cooling Cycle Temp- Dry Display erature Level time Electro- Temp- Default Temp- sensor Control time Control ** WHITES AND HIGH More Dry 50 min Saturation 68±4°C 2 min. 47±5°C COLORSTime PERMANENT MEDIUM More Dry 50 min Saturation 60±4°C 2 min. 47±5°CDry PRESS PRICE DELICATES Electric Model:52±3°C LOW More Dry 50 min Saturation 2 min. 38±5°C PRICE Gas Model:47±3°C Temperature Control for each cycle MOTOR LOAD HEATER 43
  45. 45. 11 COMPONENT TESTING INFORMATION 44
  46. 46. 45
  47. 47. 46
  48. 48. 12 MOTOR DIAGRAM AND SCHEMATIC 47
  49. 49. 13 CONTROL LAY - OUTPWB ASSEMBLY DISPLAY LAY-OUTPWB ASSEMBLY LAY-OUT 48
  50. 50. 14 WIRING DIAGRAMCAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper Operation after servicing.ELECTRIC DRYER WIRING DIAGRAM 49
  51. 51. 15 DIAGNOSTIC TEST1.This TEST should be used for Factory test /Service test. Do not use this DIAGNOSTIC TEST other than specified.2.Activating the heater manually with the door open may trip the thermostat attached to the heater, therefore do not activate it manually. (Do not press the door switch to operate the heater while the door is open). Diagnostic test: (display)This program has been added for testing the dryer and detecting errors. Entering the test mode Machine Data Name Button Display Description 1. Entering programming mode Insert service card (card type), Turn on/off toggle switch (Coin type).CARD 2. WHITES COLORS Press the WHITES COLORS button./COIN Then appears in the display. Entering 3. START Enter the diagnostic test mode. the test mode Push and hold the WHITES COLORS and DELICATES at the same time. 1. Entering programming mode. After that push PERM. PRESS button for 3 times. Push START button.OPL 2. WHITES COLORS Press the WHITES COLORS button. Then appears in the display. 3. START Enter the diagnostic test mode. 1 Pressing the START button cycles to the next test function. Number of times the START Checking point Display button is pressed None LqC 1 1 time Check the version and code of machine. Version and code of machine (All LED on) ELECTRIC TYPE : US:OE CA:OE or CA:Og and gU:XX GAS TYPE : US:Og alternately. OPL machine-Display CA:PE or CA:Pg and gU:XX alternately. XX is the version number 2 times Motor runs. Measured moisture value (70~239) 3 times ELECTRIC TYPE: Heater runs. Current temperature (5~70) Motor + Heater 1 (2700W) (Displays the temperature inside the drum in GAS TYPE: GAS valve runs. ° Celsius.) Motor + Valve ELECTRIC TYPE: Heater runs. Current temperature (5~70) 4 times Motor + Heater 1 +Heater 2 (5400W) (Displays the temperature inside the drum in GAS TYPE: GAS valve runs. ° Celsius.) Motor+Valve LED KEY CHECK Press WHITES COLORS button. Version and code of machine 5 times Press PERM.PRESS button. Press DELICATES button. 6 times Test ends. LqC 1 During check, if the door is open. Door switch dE (Motor Heater Off, Buzzer beeps seven (The door is open. Please close the door times) completely) During check, if the door is closed Test goes back at step 2. Measured moisture value (70~239) (Motor on Heater Off)NoteDuring LqC1 test, if no buttons are pressed for 4 minutes, machine will be turned off automatically.Do not use . 50
  52. 52. Test 1 240V Electrical Supply WARNING• When measuring power, be sure to wear insulated gloves to avoid an electric shock.• Failure to follow these instructions can result in death or electric shock.Trouble Symptom No power was applied to controller. (LED, LCD Display off)Measurement Condition With Dryer Power On; connector linked to controller. Check the outlet, is the voltage • Check the fuse or NO 240V AC? circuit breaker. YES BK2 or WH2 YL3 Check if the voltage measured between • Check if power Connector BK2 or WH2- 2 (Black Wire) NO cord is properly Linked to the Controller and YL3- 1 connected. (White Wire) Is 240V? YES 1 Check if the controller wire is disconnected. 2 Check if terminal block and power cord • Reconnect the NO controller. are connected (Check Plug). - Does Power Cord N (Natural) line match to Terminal Center N (Natural) line? YES Replace controIler. 51
  53. 53. WARNING 52
  54. 54. 53
  55. 55. Test 2 Thermistor Test --- Measure with Power Off 54
  56. 56. Test 3 Motor Test WARNING• Before measuring resistance, be sure to turn power off, and do voltage discharge. (When discharging, contact the metal plug of power cord with the earth line.)• Failure to follow these instructions can result in death or electric shock.Trouble Symptom Drum does not turn, fan does not blow, and heater does not operate.Measurement Condition Turn the dryer’s power off, then measure resistance. YL3 BL2 • Replace control. Is resistance below 3Ω between connector YL3- 1 (White wire) and BL2- 2 (Brown wire)? YES (Relay check) Measure while door is closed. • Check controller connector. NO • Check if door frame Is resistance below 3Ω between Connector presses door NO switch knob. YL3- 1 (White wire) and BL2- 2 Measure • Check door switch. while door is closed.(Yellow wire)? • Check harness YES connection. Is resistance below 3Ω between Connector • Replace control. BL2- 1 (Yellow wire) and BL2- 2 (Brown wire)? YES (Relay check) • Check controller connector. NO • Replace outlet Is resistance below 1Ω between terminals of • Thermostat. NO (Refer to outlet thermostat attached to blower housing? component) YES • Check idler assembly Does idle switch attached to motor bracket • Drum belt cuts off operate level by drum belt? YES • Drum belt takes off (Not operating lever is normal.) from motor pulley. Is resistance below 1Ω between idler switch • Replace idler NO switch. terminals? YES • Check motor. (Refer to Motor Diagram and Check) • Check if control connector is contacted. 55
  57. 57. Test 4 Moisture SensorWARNING 56
  58. 58. Test 5 Door switch test WARNING• Before measuring resistance, be sure to turn power off, and do voltage discharge. (When discharging, contact the metal plug of power cord with the earth line.)• Failure to follow these instructions can result in death or electric shock. Door opening is not sensed. (During operation, when opening door, drum motor andTrouble Symptom Heater run continuously) Door close is not sensed. (Drum motor will not operate. Display will flash at 1/Measurement Condition Turn the dryer’s power off, then measure resistance. BK2 YL3 Measure while door is closed. Check it resistance is • Door switch below 2500 Ω between YL3- 1 (White wire) and check (Refer to BK2- 2 Connector YES component YL3,BL2 after taking WH1,BL2 out from Controller. testing.) NO • Check lamp. (When Measure while door is open. Check it resistance is opening lamp, 300~60 Ω between YL3- 1 (White wire) and BK2- 2 replace then NO measure again.) (Black wire). Connector YL3,BL2 after taking YL3,BL2 out from controller. • Door switch check (Refer to YES component testing.) YL3 BL2 Measure while door is open. Check it resistance is • Door switch below 1 Ω between BL2- 1 (Yellow wire) and check (Refer to YES component YL3- 1 (White wire) after taking connector YL3,BL2 out from controller. testing.) NO Measure while door is closed. Check it resistance is • Door switch below 1 Ω between BL2- 1 (Yellow wire) and NO check (Refer to YL3- 1 (White wire) after taking connector YL3,BL2 component out from controller. testing.) YES Check hontroller. Check harness-linking connector. 57
  59. 59. Test 6 Heater switch test - Electric TypeWARNING 58
  60. 60. Test 7 GAS valve test - Gas TypeWARNING 59
  61. 61. 16 ERROR MODE Meaning of Error Codes that LED displays during occurrence or problem.Dryer error code PROBLEM POSSIBLE CAUSE SOLUTION It is displayed when thermistor is opened or shorted Thermistor should be replaced. It is displayed when thermistor temperature have Thermistor should be replaced. increased about 17 degrees for 10 seconds Disconnection of card reader wire. Check the card reader wire. 60
  62. 62. 17 CHANGE GAS SETTING (NATURAL GAS, PROPANE GAS) WARNING 61
  63. 63. 62
  64. 64. 18 DISASSEMBLY INSTRUCTIONS WARNING• Disassemble and repair the unit only after pulling out power plug from the outlet.• Failure to follow these instructions can result in death or electrical shock. CONTROL PANEL ASSEMBLY WARNING • When you disassemble the control panel, be sure to take gloves and careful panel frame’s edge. Failure to do so can cause serious injury. 1. Remove 2 screws on the control panel assembly. 2. Pull the control panel assembly upward and then forward. 3. Disconnct the connectors. 63
  65. 65. TOP PLATE WARNING • When you disassemble the top plate, be sure to take gloves and careful plate’s edge. Failure to do so can cause serious injury. 1. Remove 2 screws on the control panel frame. 2. Push the top plate backward forcefully. 3. Lift the plate. 64
  66. 66. LOWER COVER 1. Remove 2 screw on the lower cover. 2. Take out of the lower cover.COVER CABINET WARNING • When you disassemble the door switch connector, be sure to take gloves and careful cabinet edge. Failure to do so can cause serious injury. 1. Open the door assembly. 2. Remove 2 screws. 3. Remove 4 screws from the top of cabinet cover. 4. Disconnect the harness of door switch. 5. Disassemble the cover cabinet. 65
  67. 67. PANEL FRAME 1. Disconnect the housing of the panel frame. 2. Remove 4 screws on the panel frame. 3. Disassemble panel frame from pulling upside. Push Push LOWER FRAME 1. Disconnect the housing of the panel frame. 2. Remove 4 screw on the panel frame. 3. Disassemble lower frame from pulling forward with pushing down.PushPush 66
  68. 68. TUB DRUM [FRONT] 1. Disassemble the top plate. 2. Remove cover cabinet. 3. Disconnect the door lamp and electrode sensor connector. 4. Remove 4 screws. 5. Disassemble the tub drum front. DRUM ASSEMBLY-1 1. Disassemble the top plate. -1 2. Remove the cabinet cover and drum front. -2 3. Loosen belt from motor and idler pulleys. 4. Carefully remove the drum. 67

×