8.1
Chapter 8
Switching
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
8.2
Figure 8.1 Switched network
8.3
Figure 8.2 Taxonomy of switched networks
8.4
8-1 CIRCUIT-SWITCHED NETWORKS8-1 CIRCUIT-SWITCHED NETWORKS
A circuit-switched network consists of a set of switchesA c...
8.5
A circuit-switched network is made of a
set of switches connected by physical
links, in which each link is
divided int...
8.6
Figure 8.3 A trivial circuit-switched network
8.7
In circuit switching, the resources need
to be reserved during the setup phase;
the resources remain dedicated for the...
8.8
As a trivial example, let us use a circuit-switched network
to connect eight telephones in a small area.
Communication...
8.9
Figure 8.4 Circuit-switched network used in Example 8.1
8.10
As another example, consider a circuit-switched network
that connects computers in two remote offices of a private
co...
8.11
Figure 8.5 Circuit-switched network used in Example 8.2
8.12
Figure 8.6 Delay in a circuit-switched network
8.13
Switching at the physical layer in the
traditional telephone network uses
the circuit-switching approach.
Note
8.14
8-2 DATAGRAM NETWORKS8-2 DATAGRAM NETWORKS
In data communications, we need to send messagesIn data communications, we...
8.15
In a packet-switched network, there
is no resource reservation;
resources are allocated on demand.
Note
8.16
Figure 8.7 A datagram network with four switches (routers)
8.17
Figure 8.8 Routing table in a datagram network
8.18
A switch in a datagram network uses a
routing table that is based on the
destination address.
Note
8.19
The destination address in the header of
a packet in a datagram network
remains the same during the entire
journey of...
8.20
Figure 8.9 Delay in a datagram network
8.21
Switching in the Internet is done by
using the datagram approach
to packet switching at
the network layer.
Note
8.22
8-3 VIRTUAL-CIRCUIT NETWORKS8-3 VIRTUAL-CIRCUIT NETWORKS
A virtual-circuit network is a cross between a circuit-A vir...
8.23
Figure 8.10 Virtual-circuit network
8.24
Figure 8.11 Virtual-circuit identifier
8.25
Figure 8.12 Switch and tables in a virtual-circuit network
8.26
Figure 8.13 Source-to-destination data transfer in a virtual-circuit network
8.27
Figure 8.14 Setup request in a virtual-circuit network
8.28
Figure 8.15 Setup acknowledgment in a virtual-circuit network
8.29
In virtual-circuit switching, all packets
belonging to the same source and
destination travel the same path;
but the ...
8.30
Figure 8.16 Delay in a virtual-circuit network
8.31
Switching at the data link layer in a
switched WAN is normally
implemented by using
virtual-circuit techniques.
Note
8.32
8-4 STRUCTURE OF A SWITCH8-4 STRUCTURE OF A SWITCH
We use switches in circuit-switched and packet-We use switches in ...
8.33
Figure 8.17 Crossbar switch with three inputs and four outputs
8.34
Figure 8.18 Multistage switch
8.35
In a three-stage switch, the total
number of crosspoints is
2kN + k(N/n)2
which is much smaller than the number of
cr...
8.36
Design a three-stage, 200 × 200 switch (N = 200) with
k = 4 and n = 20.
Solution
In the first stage we have N/n or 10...
8.37
According to the Clos criterion:
n = (N/2)1/2
k > 2n – 1
Crosspoints ≥ 4N [(2N)1/2
– 1]
Note
8.38
Redesign the previous three-stage, 200 × 200 switch,
using the Clos criteria with a minimum number of
crosspoints.
So...
8.39
Figure 8.19 Time-slot interchange
8.40
Figure 8.20 Time-space-time switch
8.41
Figure 8.21 Packet switch components
8.42
Figure 8.22 Input port
8.43
Figure 8.23 Output port
8.44
Figure 8.24 A banyan switch
8.45
Figure 8.25 Examples of routing in a banyan switch
8.46
Figure 8.26 Batcher-banyan switch
Upcoming SlideShare
Loading in...5
×

Chapter 8 switching -computer_network

551

Published on

computer_network

Published in: Education
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
551
On Slideshare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
44
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Chapter 8 switching -computer_network

  1. 1. 8.1 Chapter 8 Switching Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
  2. 2. 8.2 Figure 8.1 Switched network
  3. 3. 8.3 Figure 8.2 Taxonomy of switched networks
  4. 4. 8.4 8-1 CIRCUIT-SWITCHED NETWORKS8-1 CIRCUIT-SWITCHED NETWORKS A circuit-switched network consists of a set of switchesA circuit-switched network consists of a set of switches connected by physical links. A connection between twoconnected by physical links. A connection between two stations is a dedicated path made of one or more links.stations is a dedicated path made of one or more links. However, each connection uses only one dedicatedHowever, each connection uses only one dedicated channel on each link. Each link is normally dividedchannel on each link. Each link is normally divided into n channels by using FDM or TDM.into n channels by using FDM or TDM. Three Phases Efficiency Delay Circuit-Switched Technology in Telephone Networks Topics discussed in this section:Topics discussed in this section:
  5. 5. 8.5 A circuit-switched network is made of a set of switches connected by physical links, in which each link is divided into n channels. Note
  6. 6. 8.6 Figure 8.3 A trivial circuit-switched network
  7. 7. 8.7 In circuit switching, the resources need to be reserved during the setup phase; the resources remain dedicated for the entire duration of data transfer until the teardown phase. Note
  8. 8. 8.8 As a trivial example, let us use a circuit-switched network to connect eight telephones in a small area. Communication is through 4-kHz voice channels. We assume that each link uses FDM to connect a maximum of two voice channels. The bandwidth of each link is then 8 kHz. Figure 8.4 shows the situation. Telephone 1 is connected to telephone 7; 2 to 5; 3 to 8; and 4 to 6. Of course the situation may change when new connections are made. The switch controls the connections. Example 8.1
  9. 9. 8.9 Figure 8.4 Circuit-switched network used in Example 8.1
  10. 10. 8.10 As another example, consider a circuit-switched network that connects computers in two remote offices of a private company. The offices are connected using a T-1 line leased from a communication service provider. There are two 4 × 8 (4 inputs and 8 outputs) switches in this network. For each switch, four output ports are folded into the input ports to allow communication between computers in the same office. Four other output ports allow communication between the two offices. Figure 8.5 shows the situation. Example 8.2
  11. 11. 8.11 Figure 8.5 Circuit-switched network used in Example 8.2
  12. 12. 8.12 Figure 8.6 Delay in a circuit-switched network
  13. 13. 8.13 Switching at the physical layer in the traditional telephone network uses the circuit-switching approach. Note
  14. 14. 8.14 8-2 DATAGRAM NETWORKS8-2 DATAGRAM NETWORKS In data communications, we need to send messagesIn data communications, we need to send messages from one end system to another. If the message isfrom one end system to another. If the message is going to pass through a packet-switched network, itgoing to pass through a packet-switched network, it needs to be divided into packets of fixed or variableneeds to be divided into packets of fixed or variable size. The size of the packet is determined by thesize. The size of the packet is determined by the network and the governing protocol.network and the governing protocol. Routing Table Efficiency Delay Datagram Networks in the Internet Topics discussed in this section:Topics discussed in this section:
  15. 15. 8.15 In a packet-switched network, there is no resource reservation; resources are allocated on demand. Note
  16. 16. 8.16 Figure 8.7 A datagram network with four switches (routers)
  17. 17. 8.17 Figure 8.8 Routing table in a datagram network
  18. 18. 8.18 A switch in a datagram network uses a routing table that is based on the destination address. Note
  19. 19. 8.19 The destination address in the header of a packet in a datagram network remains the same during the entire journey of the packet. Note
  20. 20. 8.20 Figure 8.9 Delay in a datagram network
  21. 21. 8.21 Switching in the Internet is done by using the datagram approach to packet switching at the network layer. Note
  22. 22. 8.22 8-3 VIRTUAL-CIRCUIT NETWORKS8-3 VIRTUAL-CIRCUIT NETWORKS A virtual-circuit network is a cross between a circuit-A virtual-circuit network is a cross between a circuit- switched network and a datagram network. It hasswitched network and a datagram network. It has some characteristics of both.some characteristics of both. Addressing Three Phases Efficiency Delay Circuit-Switched Technology in WANs Topics discussed in this section:Topics discussed in this section:
  23. 23. 8.23 Figure 8.10 Virtual-circuit network
  24. 24. 8.24 Figure 8.11 Virtual-circuit identifier
  25. 25. 8.25 Figure 8.12 Switch and tables in a virtual-circuit network
  26. 26. 8.26 Figure 8.13 Source-to-destination data transfer in a virtual-circuit network
  27. 27. 8.27 Figure 8.14 Setup request in a virtual-circuit network
  28. 28. 8.28 Figure 8.15 Setup acknowledgment in a virtual-circuit network
  29. 29. 8.29 In virtual-circuit switching, all packets belonging to the same source and destination travel the same path; but the packets may arrive at the destination with different delays if resource allocation is on demand. Note
  30. 30. 8.30 Figure 8.16 Delay in a virtual-circuit network
  31. 31. 8.31 Switching at the data link layer in a switched WAN is normally implemented by using virtual-circuit techniques. Note
  32. 32. 8.32 8-4 STRUCTURE OF A SWITCH8-4 STRUCTURE OF A SWITCH We use switches in circuit-switched and packet-We use switches in circuit-switched and packet- switched networks. In this section, we discuss theswitched networks. In this section, we discuss the structures of the switches used in each type ofstructures of the switches used in each type of network.network. Structure of Circuit Switches Structure of Packet Switches Topics discussed in this section:Topics discussed in this section:
  33. 33. 8.33 Figure 8.17 Crossbar switch with three inputs and four outputs
  34. 34. 8.34 Figure 8.18 Multistage switch
  35. 35. 8.35 In a three-stage switch, the total number of crosspoints is 2kN + k(N/n)2 which is much smaller than the number of crosspoints in a single-stage switch (N2 ). Note
  36. 36. 8.36 Design a three-stage, 200 × 200 switch (N = 200) with k = 4 and n = 20. Solution In the first stage we have N/n or 10 crossbars, each of size 20 × 4. In the second stage, we have 4 crossbars, each of size 10 × 10. In the third stage, we have 10 crossbars, each of size 4 × 20. The total number of crosspoints is 2kN + k(N/n)2 , or 2000 crosspoints. This is 5 percent of the number of crosspoints in a single-stage switch (200 × 200 = 40,000). Example 8.3
  37. 37. 8.37 According to the Clos criterion: n = (N/2)1/2 k > 2n – 1 Crosspoints ≥ 4N [(2N)1/2 – 1] Note
  38. 38. 8.38 Redesign the previous three-stage, 200 × 200 switch, using the Clos criteria with a minimum number of crosspoints. Solution We let n = (200/2)1/2 , or n = 10. We calculate k = 2n 1 =− 19. In the first stage, we have 200/10, or 20, crossbars, each with 10 × 19 crosspoints. In the second stage, we have 19 crossbars, each with 10 × 10 crosspoints. In the third stage, we have 20 crossbars each with 19 × 10 crosspoints. The total number of crosspoints is 20(10 × 19) + 19(10 × 10) + 20(19 ×10) = 9500. Example 8.4
  39. 39. 8.39 Figure 8.19 Time-slot interchange
  40. 40. 8.40 Figure 8.20 Time-space-time switch
  41. 41. 8.41 Figure 8.21 Packet switch components
  42. 42. 8.42 Figure 8.22 Input port
  43. 43. 8.43 Figure 8.23 Output port
  44. 44. 8.44 Figure 8.24 A banyan switch
  45. 45. 8.45 Figure 8.25 Examples of routing in a banyan switch
  46. 46. 8.46 Figure 8.26 Batcher-banyan switch
  1. A particular slide catching your eye?

    Clipping is a handy way to collect important slides you want to go back to later.

×