CCNAAnswers.com

CCNA 2 Chapter 10 V4.0 Answers


1. What action does a link-state router take immediately upon receipt of...
CCNAAnswers.com




Host 192.168.1.66 in the network illustrated is unable to ping host 192.168.1.130. How
must EIGRP be c...
CCNAAnswers.com

forward the packet via the route to 10.16.1.0

forward the packet via the route to 10.16.1.64

use the de...
CCNAAnswers.com




Refer to the exhibit. Routers East and West are configured using RIPv1. Both routers are
sending updat...
CCNAAnswers.com

2.




Refer to the exhibit. Which address is a broadcast address for one of the subnets that are
shown i...
CCNAAnswers.com

Router1(config-router)# no network 192.168.10.0

Router1(config-router)# passive-interface fastethernet 0...
Upcoming SlideShare
Loading in …5
×

Ccna braindumps

481 views
403 views

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
481
On SlideShare
0
From Embeds
0
Number of Embeds
3
Actions
Shares
0
Downloads
7
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Ccna braindumps

  1. 1. CCNAAnswers.com CCNA 2 Chapter 10 V4.0 Answers 1. What action does a link-state router take immediately upon receipt of an LSP from a neighboring router? floods the LSP to neighbors calculates the SPF algorithm runs the Bellman-Ford algorithm computes the best path to the destination network 2. Why is it difficult for routing loops to occur in networks that use link-state routing? Each router builds a simple view of the network based on hop count. Routers flood the network with LSAs to discover routing loops. Each router builds a complete and synchronized view of the network. Routers use hold-down timers to prevent routing loops. Read more… CCNA 2 Chapter 9 V4.0 Answers 1. What two actions will the EIGRP DUAL FSM take if a link to a network goes down? (Choose two.) put the route into passive mode query neighbors for a new route search routing table for a feasible successor run the SPF algorithm to find a new successor search topology table for a feasible successor 2.
  2. 2. CCNAAnswers.com Host 192.168.1.66 in the network illustrated is unable to ping host 192.168.1.130. How must EIGRP be configured to enable connectivity between the two hosts? (Choose two.) R1(config-router)# network 192.168.1.128 R1(config-router)# auto-summary R1(config-router)# no auto-summary R2(config-router)# no auto-summary R2(config-router)# auto-summary R2(config-router)# network 192.168.1.64 Read more… CCNA 2 Chapter 8 V4.0 Answers 1. Refer to the exhibit. Router B receives a packet with a destination address of 10.16.1.97. What will router B do? drop the packet
  3. 3. CCNAAnswers.com forward the packet via the route to 10.16.1.0 forward the packet via the route to 10.16.1.64 use the default route 2. A network is converged and the routing tables are complete. When a packet needs to be forwarded, what is the first criterion used to determine the best path in the routing table? the route with the smallest AD the route with the longest address and mask match to the destination the route with the highest bandwidth the route with the best combination of AD and lowest cost Read more… CCNA 2 Chapter 7 V4.0 Answers 1. A network administrator has been told that the company IP address infrastructure must adhere to RFC 1918. What three IP address ranges from RFC 1918 could the administrator use on the network? (Choose three.) 10.0.0.0/8 127.0.0.0/8 169.254.0.0/16 172.16.0.0/12 192.168.0.0/16 209.165.201.0/27 2.
  4. 4. CCNAAnswers.com Refer to the exhibit. Routers East and West are configured using RIPv1. Both routers are sending updates about their directly connected routes. The East router can ping the West router serial interface and West can ping the serial interface of East. However, neither router has dynamically learned routes from the other. What is most likely the problem? A gateway of last resort is required. Subnetting is not supported by RIPv1. VLSM is not supported by RIPv1. One of the routers needs a clock rate on the serial interface. Read more… CCNA 2 Chapter 6 V4.0 Answers 1. What two advantages does CIDR provide to a network? (Choose two.) reduced routing table size dynamic address assignment automatic route redistribution reduced routing update traffic automatic summarization at classful boundaries
  5. 5. CCNAAnswers.com 2. Refer to the exhibit. Which address is a broadcast address for one of the subnets that are shown in the exhibit? 192.168.4.3/29 192.168.4.15/29 192.168.4.65/26 192.168.4.255/24 Read more… CCNA 2 Chapter 5 V4.0 Answers 1. Refer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers? Router1(config-router)# no router rip Router1(config-router)# network 192.168.10.0
  6. 6. CCNAAnswers.com Router1(config-router)# no network 192.168.10.0 Router1(config-router)# passive-interface fastethernet 0/0 Router1(config-router)# passive-interface serial 0/0/0 2. Refer to the output from the show ip route command. What can be concluded from the output of this router command? A preferred route to the destination has not been set. There are two equal cost paths to network 1.0.0.0. Both interfaces are being used equally to route traffic. A variance must be set to load-balance across multiple paths.

×