Your SlideShare is downloading. ×
How to make a vag com cable – obd2 support
How to make a vag com cable – obd2 support
How to make a vag com cable – obd2 support
How to make a vag com cable – obd2 support
How to make a vag com cable – obd2 support
How to make a vag com cable – obd2 support
Upcoming SlideShare
Loading in...5
×

Thanks for flagging this SlideShare!

Oops! An error has occurred.

×
Saving this for later? Get the SlideShare app to save on your phone or tablet. Read anywhere, anytime – even offline.
Text the download link to your phone
Standard text messaging rates apply

How to make a vag com cable – obd2 support

1,394

Published on

How to make a vag com cable – obd2 support

How to make a vag com cable – obd2 support

Published in: Self Improvement, Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
1,394
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
10
Comments
0
Likes
0
Embeds 0
No embeds

Report content
Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
No notes for slide

Transcript

  • 1. car diagnostic Software installation report- AUTOCOM 2013.1 1. Nagios:xp/win7/win8 2.Install the software steps 1) 1st Step: Pls install 2013.1 delphisoftware 2)Step: Open “Autocom Delphi Patcher v2013.1”, Then click "manual Patch", replace Main in the installation directory
  • 2. 3)Step: Open “AutocomDelphiPatch”, choose installation folder "DS150E (New VCI)", and click "Ok" 4)Step: Open well-installed "DS150E (New VCI)", click next step into activation page, Open “AGK2131”, input 100251 in Serial column, choose “Delphi” in brand Column, click "Generate", input well-activated hardwarekey and serial number into registrated page. click Ok.
  • 3. 5)Finish 3. Actual Test or ECU Demo Steps (1)Test vehicles or ECU name 2004 Toyato Camry (2)Detailed steps Autocom 2013 Introduction: Interface: There are two interfaces in total. One end is used to connect the PC via USB; other end should be plugged into the vehicle directly.
  • 4. Facade: 18 cm in length; 7 cm in width; black; plastic case. Autocom 2013 Actual Test First, connect the device with the USB interface of PC via USB cable Second, plug another interface of the device into vehicle (ECU interface). Third, start the ignition device of vehicle. Third, start the Autocom 2013 software. 4. Possible problems and solutions INSTALL XP Before install the new version 2013.R1 (Autocom/Delphi) 1.First uninstall previous versions . 2.Delete the following folders: WINDOWS XP: C:ProgramsAutocom C:ProgramsDelphi C:Documents and SettingsAll UsersApplication DataAutocom C:Documents and SettingsAll UsersApplication DataDelphi C:Documents and Settings**USER**Application DataAutocom C:Documents and Settings**USER**Application DataDelphi C:Documents and Settings**USER**Application DataMicrosoftSystemCertificatesMy C:Documents and SettingsDefault UserApplication DataMicrosoftSystemCertificatesMy C:Documents and SettingsLocalServiceApplication DataMicrosoftSystemCertificatesMy C:Documents and SettingsNetworkServiceApplication DataMicrosoftSystemCertificatesMy WINDOWS 7 & 8: C:Programsx86Autocom C:Programsx86Delphi C:users**USER**AppDataRoamingDelphi C:users**USER**AppDataRoamingAutocom C:users**USER**AppDataRoamingMicrosoftSystemCertificatesMy OTHER OS: Look similar folders. . 3.Edit with Notepad: C:WINDOWSsystem32driversetchosts
  • 5. and delete: 127.0.0.1 activation.autocom.se 127.0.0.1 activation2.autocom.se . 4.Run CCleaner and clean the registry . 5.Restart your computer . 6.Install new version 2013.R1 Article is edited by XCAR360.com original, reproduced please indicate the source, ths!
  • 6. and delete: 127.0.0.1 activation.autocom.se 127.0.0.1 activation2.autocom.se . 4.Run CCleaner and clean the registry . 5.Restart your computer . 6.Install new version 2013.R1 Article is edited by XCAR360.com original, reproduced please indicate the source, ths!

×