Your SlideShare is downloading. ×
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Overview Of Chapter 8
Upcoming SlideShare
Loading in...5
×

Thanks for flagging this SlideShare!

Oops! An error has occurred.

×
Saving this for later? Get the SlideShare app to save on your phone or tablet. Read anywhere, anytime – even offline.
Text the download link to your phone
Standard text messaging rates apply

Overview Of Chapter 8

180

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
180
On Slideshare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
0
Comments
0
Likes
0
Embeds 0
No embeds

Report content
Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
No notes for slide

Transcript

  • 1. Overview of Chapter 8 Standard Gary Nelson Iain Walker Brett Dillon RESNET Conference 2011, Orlando FLMonday, March 14, 2011
  • 2. Presenter Info • Gary Nelson • Iain Walker • Scientist • Brett Dillon • President • Lawrence • Chair, TC • The Energy Berkeley National • IBS Advisors, LLC Conservatory LaboratoryMonday, March 14, 2011
  • 3. TC Litmus Test 1. Accuracy 2. Profitability 3. EasierMonday, March 14, 2011
  • 4. Technical Committee Process • Work assigned to Performance Testing Subcommittee • Draft created & reviewed by full Technical Committee for comments • Technical Committee comments addressed by Subcommittee • 2nd version released for Technical Committee vote to go out for public comment • Sent to Board of Directors for vote to release for public comment • Public comments received • Public comments addressed by Subcommittee • Revised version sent to full Technical Committee for vote • If approved, sent to Standards Committee & then Board for approval • If not approved, sent back to Subcommittee for further revisionMonday, March 14, 2011
  • 5. Chapter 8 Content • Infrared (already approved & released by Board of Directors), session 7, Wednesday Salon 7 • Combustion Safety & Work Scope (already approved & released by Board of Directors), session 8, Wednesday Salon 3 • Infiltration Testing • Duct Leakage Testing • Ventilation & Exhaust Flow Testing • Static Pressure Testing (to be done next)Monday, March 14, 2011
  • 6. Infiltration • Standard Level of Accuracy • Reduced Level of Accuracy • Single Point Test • Multi-point Test • Repeated Single Point TestMonday, March 14, 2011
  • 7. Standard Level of Accuracy • Baseline pressure < 5.0 Pa • Record indoor & outdoor temperatures within 10º F • Record altitude if > 5,000 ft above sea levelMonday, March 14, 2011
  • 8. Reduced Level of Accuracy • Baseline pressure > 5.0 Pa, < 10 Pa • Record indoor & outdoor temperatures within 10º F • Record altitude if > 5,000 ft above sea level • Corrected CFM50 x extending factor (1 + (0.1 x (50 / induced building pressure)))Monday, March 14, 2011
  • 9. Single Point Test • Baseline readings • ∆ 50 Pa • If above 5,000 feet or ∆ T > 30º F, CFM50 must be corrected • Altitude correction = 1 + (0.000006 x altitude) • Temperature correction found in table • Nominal CFM50 x altitude correction x temperature correction = corrected CFM50Monday, March 14, 2011
  • 10. Multi-point Test • Baseline readings • ∆ 60 Pa • 7 additional readings between 15 Pa & 60 Pa, equally spaced • If uncertainty < 10%, Standard Level of Accuracy • If uncertainty > 10%, Reduced Level of AccuracyMonday, March 14, 2011
  • 11. Monday, March 14, 2011
  • 12. Repeated Single Point Test • Baseline readings • ∆ 50 Pa 5x • Performed 5 x • Average CFM50 readings • Average corrected CFM50 = average nominal CFM50 x altitude correction x temperature correctionMonday, March 14, 2011
  • 13. Duct Leakage • Leakage to Outside • RESNET Standard • ASHRAE Std 152, Annex B • ASTM Std E-1554, Method A • ASTM Std E-1554, Method B • Total Leakage • RESNET Standard • ASHRAE Std 152, Annex CMonday, March 14, 2011
  • 14. Air Handler Flow Measured airflow OR 400 cfm/ton A/C OR 400 cfm/ton Heat Pump OR 200 cfm/12,000 Btu/hr Furnace whichever is greatestMonday, March 14, 2011
  • 15. Monday, March 14, 2011
  • 16. Monday, March 14, 2011
  • 17. Leakage to Outside • RESNET Std • 25 Pa • 1/2 supply, 1/2 return • ASHRAE Std 152, B • 25 Pa • 1/2 plenum pressure for supply & return individually • Separate supply & return • ASTM E-1554 “A” (Delta Q) • Normal operation • Separate supply & return • Not used for compliance • Enclosure leakage < 2500 CFM50 • ASTM E-1554 “B” • 25 Pa • 1/2 plenum pressure for supply & return individually • Separate supply & returnMonday, March 14, 2011
  • 18. Total Leakage • RESNET Std • 25 Pa • 1/2 supply, 1/2 return • ASHRAE Std 152, C • 25 Pa • 1/2 plenum pressure OR 62.5 Pa • 1/2 supply, 1/2 return • 2.5% airhandler flow added if airhandler not present • 2.5% airhandler flow added if registers/grilles not presentMonday, March 14, 2011
  • 19. Ventilation & Exhaust Flows •Powered Flow Hood •Air Flow Resistance •Garbage BagMonday, March 14, 2011
  • 20. Monday, March 14, 2011
  • 21. Dr. Iain Walker iswalker@lbl.gov Gary Nelson info@energyconservatory.com Brett Dillon info@ibsadvisorsllc.comMonday, March 14, 2011

×