Your SlideShare is downloading. ×
Report Format 2009
Upcoming SlideShare
Loading in...5
×

Thanks for flagging this SlideShare!

Oops! An error has occurred.

×

Introducing the official SlideShare app

Stunning, full-screen experience for iPhone and Android

Text the download link to your phone

Standard text messaging rates apply

Report Format 2009

1,830
views

Published on

Published in: Technology, Business

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
1,830
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
32
Comments
0
Likes
0
Embeds 0
No embeds

Report content
Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
No notes for slide

Transcript

  • 1. Important Instructions for Report Writing for M E (Mechanical) Seminar II 1. Prepare 1 (Each per Student) + 1 (Guide) + 1(Department Library) seminar report. For example per student group 3 copies are required. 2. Limit the project report to Maximum 20 pages. 3. Footer i. “SCOE, Mechanical Engineering 2008-09” ii. Times New Roman, 10 pt, Centrally aligned. iii. Insert page number on next line of footer, center aligned, Times New Roman, 10 pt. 4. Report : i. Main part of report should be Times New Roman, 12 pt, justified, 1.5 line spacing ii. Paper Size A4 (8.5” x 11” ( 210 x 197 mm) iii. Margins Top : 1” (25 mm) Bottom : 1.32” (34 mm) Right : 1” (25 mm) Left : 1.5” (37 mm) iv. Paragraph Line spacing 1.5 Double space between two paragraphs Each paragraph shall begin with five space indentation. Times New Roman; 12 pt, Justified v. Titles (No chapters in seminar report) Section Titles Bold, 14 pt; Times New Roman; Center aligned; Title Case Sub Section Headings Bold, 12 pt; Capital (Upper Case); Left aligned; Sub Sub Section Titles Bold, 12pt; Title Case; Left aligned; 5. Illustrations (Charts, drawings, photographs, figures) are to be in the text. Use only illustrations really pertinent to the text. Illustrations must be sharp, clear, black and white, (Illustrations downloaded from internet are not acceptable.) i. Illustrations should not be more than two per page ii. Figure (and graph) No and title at bottom, Times New Roman 10 pt, center aligned iii. Graph Legends - below the title in Times New Roman 10 pt iv. Table Titles and no at top, Times New Roman 10 pt, left aligned v. Table, figures and graphs are to be center aligned. vi. Photographs if any should be on glossy prints vii. Blue prints if any are to be attached at end of report 6. Only SI system of units shall be followed in all calculations. Units other than SI units may be placed in brackets. 7. References should be in the alphabetical order by last name of first author. In case of one (or two) authors, write name and for more than two write first author with et. al. 8. Symbols and notations if any should be included in nomenclature section only.
  • 2. 9. Following will be order of report. i. Cover page and front page as per specimen on separate sheet. ii. Certificate from Institute as per specimen on separate sheet iii. Certificate from Industry on separate sheet iv. Acknowledgement v. List of figures vi. List of tables vii. List of plates viii.Nomenclature ix. Contents x. Abstract (A brief abstract of the report not more than 300 words. The heading “Abstract” should be bold, Times New Roman 12 pt, centrally aligned. Contents of abstract should be on new line without indentation.) 1. Introduction . . . .Other sections in continuation ( Please do not start next section on new page) References xi. Appendices are not allowed. 10. All section heading and subheadings should be numbered. For sections use numbers 1, 2, 3, .. and for sub section use 1.1, 1.2 etc. and sub sub section 2.1.1, 3.1.2 etc. 11. References should be given in the body of the text and well spread. No verbatim copy or excessive text from only one or two references. If figures and tables are taken from any reference then indicate source of it. Please follow following procedure for references. (Times New Roman, 12 pt, justified and numbered) i. Reference Books Collier G J and Thome J R, Convective boiling and condensations, 3/e, Oxford University Press, UK 1996, pp 110-112 ii. Papers from Journals or transactions Jund D S, and Radermacher, R, Transport properties and surface tension of pure and mixed refrigerants, ASHRAE Trans, 1991, 97(1), p 90-98 iii. Papers from conference Proceedings Colbourne D, and Ritter, T J, Quantitatve assessment of flammable refrierants in room air conditioners, Proceedings of the Sixteenth International Compressor Engineering Conference and Ninth International Refrigeration and Air Conditioning Conference, Purdue University, West Lafayette, Indinana, USA, 2002 iv. Reports, Handbooks etc, United Nations Environmental Programme, Report of the Refrigerations, Air Conditioning and Heat Pumps. Technical Option Committee, 2002 Assessment, 2002 v. Patent Patent no, Country ( in parenthesis), Date of applications, title, year. If taken from Abstract, give cross references as Cf, CA, ... vi. Internet www.(Complete site address)
  • 3. 12. Binding i. Hard Bound ii. Golden Embossing of Cover page
  • 4. A Report on PROJECT STAGE-I EXPERIMENTAL ANALYSIS OF SOLAR AIR HEATER BY MAKING THE ABSORBER PLATE ROUGH By Ashish N. Taywade Guide Prof. P. M. Khanwalkar Mechanical Engineering Department Sinhgad College of Engineering, Pune 411 041 [2009-10]
  • 5. Sinhgad Technical Education Society’s Sinhgad College of Engineering, Pune 41 CERTIFICATE This is to certify that Ashish N. Taywade, has successfully completed the seminar work entitled “EXPERIMENTAL ANALYSIS OF SOLAR AIR HEATER BY MAKING THE ABSORBER PLATE ROUGH” as Seminar II in the partial fulfillment of M. E. (Mechanical) in Design/ Heat Power/ Mechatronics Engineering. And this work has been carried out in my presence. Date : Place : Pune Guide Coordinator Name of Guide Designation Examinar Prof. (Dr) P J Awasare Head Mechanical Engineering Department
  • 6. ACKNOWLEDGEMENT I take this opportunity with great pleasure to express my deep sense of gratitude towards my esteemed guide Prof.P.M.Khanwalkar his valuable guidance and incessant encouragement and co-operation extended to me during this seminar work. I am also thankful to Prof.K.V.Mali and Prof.S.A.Kulkarni for his encouragement and moral support during seminar work. I am thankful to Dr.P.J.Awasare (Head of Department of Mechanical Engineering), Sinhgad College of Engineering, for providing all Departmental facilities for this work. I would also like to thank Dr.A.S.Padalkar (Principal, Sinhgad College of Engineering) for their unflinching help, support and cooperation during the seminar work. (Ashish N. Taywade)
  • 7. INDEX Sr. No Contents Page no 1 Introduction 1 2 Literature survey 5 3 Methodology 9 4 Activity chart 10 5 Conclusion 17 References 18