• Share
  • Email
  • Embed
  • Like
  • Save
  • Private Content
9.3 d scanning and printing (mar 21)
 

9.3 d scanning and printing (mar 21)

on

  • 867 views

9.3D scanning and printing (Mar 21)

9.3D scanning and printing (Mar 21)
WALTER GONZALES ARNAO

Statistics

Views

Total Views
867
Views on SlideShare
763
Embed Views
104

Actions

Likes
0
Downloads
60
Comments
0

3 Embeds 104

http://academy.cba.mit.edu 99
http://jasonlabs.com 4
http://fabacademy.org 1

Accessibility

Categories

Upload Details

Uploaded via as Adobe PDF

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

    9.3 d scanning and printing (mar 21) 9.3 d scanning and printing (mar 21) Presentation Transcript

    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTESSTUDENT: WALTER HECTOR GONZALES ARNAOCLASS 9: Fab3D scanning and academyprinting (Mar 21) 2012
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academyFIRST STEP. is chosen in order to experience quick scan that is 10 cm highCLASS 9: 3D scanning and printing (Mar 21) 2012
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP TWO. scanner takes pictures in revolution, as seen in the images selectedfor this purpose 2012CLASS 9: 3D scanning and printing (Mar 21)
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 3. install the program to work the volume scan CLASS 9: 3D scanning and printing (Mar 21) 2012
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 4. then the volume identifies areas that have holes to coverthem and that the 3D printing machine Acknowledge it withoutproblem 2012CLASS 9: 3D scanning and printing (Mar 21)
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 5. commands that allow for the filling operation can bedisplayed in grid mode of amending the rhino also 2012CLASS 9: 3D scanning and printing (Mar 21)
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 6. the rhino is easier to change scaleCLASS 9: 3D scanning and printing (Mar 21) 2012
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 7. opens the file in the software up to prepare for printingCLASS 9: 3D scanning and printing (Mar 21) 2012
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 8. volume is entered in the software modified UP! 3Dprinting 2012CLASS 9: 3D scanning and printing (Mar 21)
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 9. once the 3D scan is taken supercie part of the contactand then proceeded to withdraw the burr that is in contact withthe scanned object 2012CLASS 9: 3D scanning and printing (Mar 21)
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 10. appreciated that the bed volume is scanned, whichallows easy disassembly, after completion of the operation 2012CLASS 9: 3D scanning and printing (Mar 21)
    • UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 11. shown in the detail photos of the impression that it isnot as accurate 2012CLASS 9: 3D scanning and printing (Mar 21)
    • UNIVERSIDAD NACIONAL DE INGENIERÍAConclusions. FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES1. reproduction is not asaccurate, because the level ofdetail of the original ceramicfinishes imperfect2. volume changes were madein the rhino scanstudio and thento close the holes, the latter is Fabfaster academy STEP 12.SE turned on the LET CLASS 9: 3D scanning and printing (Mar 21) 2012