Your SlideShare is downloading. ×
0
4.electronics production(Feb 15)STUDENT: WALTER HECTOR GONZALES ARNAO                                        Fab academy 2...
Fabsummary -This week assigment is to make a FabISP. -using Roland MDX-20 Milling Machine -for this we will have to progra...
Fab academyFIRST STEP. WILL WORK WITH THE BOARTCLASS 4: electronics production (Feb 15)                                   ...
FabSTEP 2.-Then we setup the MDX-20,                                                                                  acad...
Fab                                           academySTEP 3.Downloading files,CLASS 4: electronics production (Feb 15)    ...
Fab                                                                       academySTEP 4.-Tools and materials, such as: sol...
Fab                                                            academySTEP 5.PRESENTED PROBLEMS TO FIND THE FILES to run I...
STEP 6.-upon completion of the construction of the card - Then following the tutorial I installed the AVR programming soft...
Conclusions.conclusions1. This has been a hardwork, especially . We had to calibrate the table of themilling machine,     ...
Upcoming SlideShare
Loading in...5
×

4.electronics production (feb 15)

403

Published on

4.electronics production (Feb 15)
WALTER GONZALES ARNAO

Published in: Technology, Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
403
On Slideshare
0
From Embeds
0
Number of Embeds
2
Actions
Shares
0
Downloads
1
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Transcript of "4.electronics production (feb 15)"

  1. 1. 4.electronics production(Feb 15)STUDENT: WALTER HECTOR GONZALES ARNAO Fab academy 2012 UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
  2. 2. Fabsummary -This week assigment is to make a FabISP. -using Roland MDX-20 Milling Machine -for this we will have to programmer in-circuit academy -then assemble the SMD components, test for shorts or open circuits and thentest and program the FabISP.CLASS 4: electronics production (Feb 15) UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
  3. 3. Fab academyFIRST STEP. WILL WORK WITH THE BOARTCLASS 4: electronics production (Feb 15) UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
  4. 4. FabSTEP 2.-Then we setup the MDX-20, academy-Installing the board on the milling table and also the milling tool (1/32" forcutting and 1/64" for milling). CLASS 4: electronics production (Feb 15) UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
  5. 5. Fab academySTEP 3.Downloading files,CLASS 4: electronics production (Feb 15) 2012 UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
  6. 6. Fab academySTEP 4.-Tools and materials, such as: soldering station, solder wire, thirdhand with magnifying loupe, tweezers and rosin flux 2012 UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
  7. 7. Fab academySTEP 5.PRESENTED PROBLEMS TO FIND THE FILES to run IN BOART, BUTAT THE END OF PLACING PROPERLY 2012 UNIVERSIDAD NACIONAL DE INGENIERÍACLASS 4: electronics production (Feb 15) FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
  8. 8. STEP 6.-upon completion of the construction of the card - Then following the tutorial I installed the AVR programming software and Fab academydownloaded the firmware.zip file for programming the FabISP.-Testing and programming the FabISP 2012 UNIVERSIDAD NACIONAL DE INGENIERÍACLASS 4: electronics production (Feb 15) FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
  9. 9. Conclusions.conclusions1. This has been a hardwork, especially . We had to calibrate the table of themilling machine, Fab 2. When connected the ATTiny to the programmer, first we got a red light, sowith the multimeter we measured the voltage supply of the ATTiny and found ashort circuit, wich was fixed.3. I asked for help to our colleagues, for the programming, the support was academyRoberto. STEP 7.SE turned on the LET CLASS 4: electronics production (Feb 15) 2012 UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
  1. A particular slide catching your eye?

    Clipping is a handy way to collect important slides you want to go back to later.

×