3 d scanning and printing (mar 21)

659 views

Published on

trabajo del fab

Published in: Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
659
On SlideShare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
7
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

3 d scanning and printing (mar 21)

  1. 1. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTESSTUDENT: WALTER HECTOR GONZALES ARNAOCLASS 9: Fab3D scanning and academyprinting (Mar 21) 2012
  2. 2. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academyFIRST STEP. is chosen in order to experience quick scan that is 10 cm highCLASS 9: 3D scanning and printing (Mar 21) 2012
  3. 3. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP TWO. scanner takes pictures in revolution, as seen in the images selectedfor this purpose 2012CLASS 9: 3D scanning and printing (Mar 21)
  4. 4. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 3. install the program to work the volume scanCLASS 9: 3D scanning and printing (Mar 21) 2012
  5. 5. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 4. then the volume identifies areas that have holes to coverthem and that the 3D printing machine Acknowledge it withoutproblem 2012CLASS 9: 3D scanning and printing (Mar 21)
  6. 6. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 5. commands that allow for the filling operation can bedisplayed in grid mode of amending the rhino also 2012CLASS 9: 3D scanning and printing (Mar 21)
  7. 7. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 6. the rhino is easier to change scaleCLASS 9: 3D scanning and printing (Mar 21) 2012
  8. 8. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 7. volume is entered in the software modified UP! 3Dprinting 2012CLASS 9: 3D scanning and printing (Mar 21)
  9. 9. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 8. once the 3D scan is taken supercie part of the contactand then proceeded to withdraw the burr that is in contact withthe scanned object 2012CLASS 9: 3D scanning and printing (Mar 21)
  10. 10. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 9. appreciated that the bed volume is scanned, whichallows easy disassembly, after completion of the operation 2012CLASS 9: 3D scanning and printing (Mar 21)
  11. 11. UNIVERSIDAD NACIONAL DE INGENIERÍA FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES Fab academySTEP 10. shown in the detail photos of the impression that it isnot as accurate 2012CLASS 9: 3D scanning and printing (Mar 21)
  12. 12. UNIVERSIDAD NACIONAL DE INGENIERÍAConclusions. FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES1. reproduction is not asaccurate, because the level ofdetail of the original ceramicfinishes imperfect2. volume changes were madein the rhino scanstudio and thento close the holes, the latter is Fabfaster academy STEP 11.SE turned on the LET CLASS 9: 3D scanning and printing (Mar 21) 2012

×