• Share
  • Email
  • Embed
  • Like
  • Save
  • Private Content
Baby Frock
 

Baby Frock

on

  • 11,713 views

THIS PPT CONTAINS ALL THE NECESSARY DETAILS NEEDED TO CONSTRUCT A BABA SUIT.

THIS PPT CONTAINS ALL THE NECESSARY DETAILS NEEDED TO CONSTRUCT A BABA SUIT.

Statistics

Views

Total Views
11,713
Views on SlideShare
11,682
Embed Views
31

Actions

Likes
0
Downloads
45
Comments
0

1 Embed 31

http://www.slideshare.net 31

Accessibility

Upload Details

Uploaded via as Microsoft PowerPoint

Usage Rights

© All Rights Reserved

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Processing…
Post Comment
Edit your comment

    Baby Frock Baby Frock Presentation Transcript

    • BABY FROCK INTRODUCTION This is garment worn by girls of age groups 3 and more. It is also called A-line frock. It is worn in summer.
    • FLAT PATTERN
      • MEASUREMENTS REQUIRED
      • Chest=20”
      • Back width=9”
      • Back waist length=9”
      • Frock length=18”
      • Short sleeve length=4.5”
      • Lower arm circumference=8”
      • Full sleeve length=13”
      • Wrist circumference=5.5”
      • Hip=21”
      • Waist to hip=4”
    • FABRIC REQUIREMENT Fabric width=36” A-Line frock: Frock length+5”=23” A-Line frock with sleeve and collar: Frock length+sleeve length+6”=28.5 ” Frock with plain bodice, gathered skirt, peterpan collar and puff sleeve: Twice frock length+sleeve length+9”=49.5”
      • FABRIC TYPE
      • Poplin
      • Rubea
      • Lone
      • Cambric
      • Satin
      • Terricott
      • Net
    • DRAFTING PROCEDURE
      • BASIC BODICE
      • Construct rectangle ABCD with the following measurements
      • AB=1/4(chest + 5” ease allowance) =6.25”
      • AD=BC=back waist length+1/2”.
      • Mark AG=1/2 back width=4.5”
      • AF=1/12 Chest
      • AH=1”
      • AJ=1/12 chest+1/4”= AF+1/4”
      • GK=1”
      • Connect HF with a bold line as shown. This is the back neck line.
      • Connect JF with dotted line as shown. This is the front neck line.
      • Connect FK with a straight line. This is the shoulder seam.
      • Mark BL=1/4 chest=5”
      • Draws GO parallel to and equal to BL.
      • Mark KX=1/3 KO and XY=1/2”.
      • Connect KXL as shown with a bold line. This is the back armscye line.
      • Mark CM=1/2”.connect LM. This is the side seam.
      • BABY FROCK
      • This is adopted from the bodice pattern as below.
      • Trace the basic front bodice pattern on a large sheet of
      • paper and label it as JFKLMD.
      • Extend the center front line JD till T taking DT=skirt length.
      • Draw TT1=L1L+1 to 1.5” depending on the flare required.
      • Connect LT1 with a straight line.
      • Mark LU=L1T.
      • Connect TU as shown for hem line.
      • If you desire to have shaping near the waistline, connect
      • MU and take LMU as the side seam.
      • SEAM ALLOWANCE:
      • Leave ¼” for neckline and collar
      • Leave 3” for skirt hem
      • Leave 1” for sleeve hem.
      • Leave ½” for all other seams
    • CONSTRUCTION PROCEDURE
      • Join shoulder seams
      • Finish placket opening at the back
      • Finish the neckline with shaped facing
      • Finish the side seams
      • Finish bottom hem
    • LAY OUT
    • VARIATIONS
    •  
      • THANK YOU